METHVEN KEA Installation Instructions Manual

Page 1
Maintenance
In the unusual event that your products performance may have deteriorated over a period of time . The bath shower mixer cartridge(s) (4 or 20) may require cleaning. To do so :-
1. Ensure that both the Hot and Cold water supplies are isolated.
2. Remove Cap(s) (1) and undo Grubscrew(s) (2). This will allow Handle(s) (3) to be removed. The Tap cartridge(s) (4 or 20) are now exposed.
3. Unscrew and remove the Cartridge(s) (4 or 20) from the bath shower mixer (5). Take note of which side each cartridge was removed from. ie left or right. This is important for correct operation after re-assembly.
4. Taking care with the Cartridge(s) (4 or 20), soak the Cartridge(s) (4 or 20) in a suitable de-scalant or mild detergent, taking care not to damage the cartridge(s) seals and then gently rinse the Cartridge(s) (4 or 20) clean.
5. Ensure there is no debris inside the Bath shower mixer (5), taking care not to damage any sealing faces.
6. Refit the Cartridge(s) (4 or 20) to the bath shower mixer body (5) (ensure each cartridge is fitted in the correct side) and tighten. Please do not over tighten the cartridge into the tap body as it may
permanently damage the cartridge.
7. Ensuring the Cartridge(s) (4 or 20) are in the ‘Off’ position , refit the Tap handle (3), tighten Grubscrew (2) and refit Cap (1).
8. Turn on the hot and cold water supplies to the bath filler , check the correct operation of the bath shower mixer and any joints around the bath shower mixer for leaks.
9. Turn off the bath shower mixer
KEA Bath Shower Mixer
Installation Instructions
Your product should be fitted in compliance with the Water Authority Regulations. If you are unsure as to what the regulations require, you can contact your Local Water Authority for further details.
Before commencing installation please ensure that you have :-
Product Care
To maintain a high quality finish of your product , you should avoid using any abrasive detergents. Some detergents will aggressively attack the surface over a period of time leading to irreversible damage. Instead, it is advisable to use a soft cloth with warm water . This will significantly prolong the life and looks of the product. If for some reason you need to use a detergent when cleaning , only use a low concentrated brand.
Warranty
Methven warrants this product against manufacturing defects and that it is suitable for use under the general operating conditions specified in this instruction sheet. However, regional regulations apply and may affect your warranty. Please refer to www.methven.com or call customer service for full details.
New Zealand Australia UK 0800 804 222 1300 638 483 0800 195 1602
INST 290 ISSUE C
1. Checked the contents of the box to ensure all parts are present and correct.
2. Read these instructions carefully to understand the installation requirement.
3. Obtained the correct tools to perform a trouble free installation.
4. Considered the surrounding environment where the installation is to take place and any potential hidden dangers.
Taking the above into consideration should result in a smoother, trouble free installation
Page 2
Operating Conditions
Part Code Description
1 T10060 Cap 2 30100595 Grubscrew 3 B50130-002 Handle 4 E20137 Hot Cartridge 5 B50150-001 Bath/shower mixer Body 6 40000048 Inlet Tail Sealing Washer 7 B50130-004 Inlet Tail 8 B50130-003 Plinth
9 40000082 Plinth Seal 10 B51031-008 Sealing Washer 11 B51031-009 Nut 12 40000024 13 A12500-007 14 30100119 15 A10040-003 16 B50150-002 17 B50150-003 18 B50150-005 19 B50150-007 20 E20136 Cold Cartridge 21 B55130-003 22 B55120-002 23 B55080-006 24 B55580-015 25 B55600-008 26 B50150-004 27 B28070-016 Flow Straightener
Your Bath shower mixer is designed to be used in conjunction with either High or Low water pressure systems. Your product should be fitted in compliance with the Water Authority Regulations. If you are unsure as to what the regulations require, You can contact your Local Water Authority for further details.
Minimum operating pressure = 0.5 bar Maximum operating pressure = 5 bar Maximum Static Pressure = 10 bar
Contents
Shower outlet Swivel Connector
Divertor Assembly
Important Note:­The swivel outlet (19) should be direct to either side of the bath spout to avoid interference with the water flow from the bath spout outlet.
Outlet position ok
Outlet position ok
Do not position in this direction
Product Dimensions
2
Important points to note before commencing Installation of your Bath shower mixer. You should have :-
a. Checked the contents of the box and all parts are present and correct. b Checked to ensure the minimum site operating conditions can be met. c. The correct tools to perform a trouble free installation. d. Considered the surrounding environment where the installation is to take place and any potential hidden dangers. e. Isolated both the hot and cold water supplies.
Note : If not already present , you may wish to consider installing isolation valves for ease of future maintenance. Isolation valves can be fitted anywhere prior to connecting the Bath shower mixer to the water supply pipes. However , they should always be installed in a safe and convenient place for ease of future access.
Installation
1. Ensure that both the Hot and Cold water supplies are isolated.
2. Taking the bath shower mixer, place the Plinth seal(s) (9) under the Plinth(s) (8), seat the bath shower mixer onto the bath, whilst still ensuring that the Plinth seal(s) (9) is correctly located under the Plinth(s)(8).
Failure to do this may result in water leakage during use between the base of the bath shower mixer and the bath.
3. Place Sealing washer(s) (10) onto the Inlet tail(s) (7) and then screw Nut(s) (11) onto the Inlet tail(s) (7), but do not fully tighten. Correctly align the bath shower mixer to the desired position on the bath and whilst holding the bath shower mixer, tighten Nut(s) (11) until the bath shower mixer is firmly fixed in the correct position.
4. Your bath shower mixer should now be firmly fixed in position.
5. Connect the ‘Hot’ water supply to the ‘Hot’ inlet tail (7). (This is usually the left inlet tail when viewed from the front) and the ‘Cold’ water supply to the ‘Cold’ inlet tail (7)
6. Check all joints are tight and the water connections have been made correctly.
7. Ensure that the shower outlet swivel connector (19) has the water outlet directed to either side of the spout (see diagram on page 2 , position ‘ok’) . Failure to do this will lead to the shower hose obstructing the bath fill outlet.
8. Connect the shower hose to the Handset and the Shower outlet swivel connector (19) at the other end.
9. Fit the shower handset into the wall mount bracket , place the wall mount bracket against the wall to find a suitable place to fix the wall mount bracket (Note - when deciding where to fix the wall mount bracket , please ensure that the shower hose will not be stretched or subjected to any unnecessary tight bends). Once a suitable place is found , mark the position of the wall mount bracket . Remove the shower handset and fix the wall mount bracket to the wall taking care of any hidden pipes when doing so.
10. Place the handset into the wall mount bracket
11. Turn on the ‘Cold’ water supply.
12. Slowly turn on the ‘Cold’ bath tap as there may be a sudden spurt of water. Then turn the bath tap on and off several times and ensure water flows through the tap outlet and also the tap turns off correctly whilst continuing to check all joints for any leaks. Please note, it is advisable to check the joints for several minutes to ensure all joints are water tight.
13. Turn off the ‘Cold’ bath tap.
14. Turn on the ‘Hot’ water supply and repeat the above process for the ‘Hot’ bath tap. Caution should be taken when working with ‘Hot’ water to prevent scalding.
15. Now turn on both hot and cold bath taps to ensure a mixed water temperature can be achieved.
16. Take hold of the shower handset , Lift the diverter knob and check that the water now diverts to the handset . Check all joints to ensure that there are no leaks
17. Turn off both hot and cold bath taps. Congratulations you have now successfully installed your new KEA bath shower mixer.
3
Loading...