meteor-kls C-240 Operator's Manual

C-240
DMX LIGHTING CONTROLLER
Operators Manual
MLSC Inc.
MLSC Inc.MLSC Inc.
MLSC Inc.
8000 Madison Pike, Madison, Alabama 35758
Tel (256) 461–8000 Fax: (256) 461–7708
Website: meteor-global.com e-mail: sales@meteor-usa.com
METEOR C
METEOR CMETEOR C
METEOR C----240
240240
240
CONTROLLER
Please read these instructions carefully before attempting to operate / program controller. Once you feel you understand the instructions, locate the instructions in a place where you will remember where they are for future reference and additional help in using your controller
CONTENTS:
1 -
INTRODUCTION / FEATURES
(PAGE 1)
2 -
FUNCTIONS
(PAGES 2 / 3)
3 -
OPERATING INSTRUCTIONS
(PAGES 3 – 11)
4 -
TROUBLE SHOOTING
(PAGES 11 / 12)
1.
INTRODUCTION / FEATURES
The C- 240 CONTROLLER is a standard DMX 512 Controller capable of controlling up to 240 DMX channels simultaneously. The main features include:
12 fixtures up to 20 channels each 30 banks of 8 Scenes each for a total of 240 scenes 6 Chases – each up to 240 Scenes
8 Faders to adjust DMX output level from 0 – 255. 2 Faders control Speed / Fade Time MIDI
control through MIDI Interface
Built in Microphone for Sound to Light / or Audio Jack
Blackout Button
Ease of Operation and Programming and copying scenes Mix and Match any DMX Lighting fixture
SPECIFICATIONS:
Power Input: DC9 – 12v 300mA DMX OUTPUT: 3 Pin Female XLR connector Size: 19” (rack-mountable) x 5.25” h x 3” d Power supply
: included
(1)
2 3
3
2
1
446 7 81 5
5
7
8
9
10
11
12
MIDI
METEOR-KLS
C-240
Program
Music
Bank-Copy
0.i /Sec.
10 Min
SPEED
FADE TIME
30 sec.
0
Scenes
PAN(9-19)
TILT(10-20)
RECORD
FINE MODE
DELETE
AUTO
TAP DISPLAY
BANK
BLACKOUT
CHASE 1
CHASE 4
CHASE2
CHASE 5
CHASE 6
HEATING ELEMENT
FOG
MACHINE
PAGES
A
PAGE
SELECT
B
2
FUNCTIONS / Buttons:
Front Control Panel
1) Scanners: to select any or all of the 12 units
2) Scenes: To store or run scenes
3) Page Select: To select Page A for Channel 1 to 8, or B for channels 9-16.
4)
LCD Display:
4 digit showing numeric
value of DMX channel / Level
5) Bank ( up / down) : 30 banks are available for use in selecting
6) Chases: To Select 1 – 6 Chases
7) Blackout – Disables all active channel outputs without going into a DMX reset
8) Program: to activate the program mode. Display flashes when activated
9) Midi / Add: To control MIDI operations of
activates save functions.
10) Auto/Del: to Select Auto Run in Chase mode or delete scenes and / or chases
11) Music / Bank Copy: to trigger the Sound Activation in Chase mode or to copy a bank of scenes from one to another in program mode
12) Tap SYNC/ Display: In Auto Chase mode used to change the Rate of Chase and in Program Mode to change LCD display value.
13) Fade Time Slider: To adjust the Fade Time – fade time is the time takes the
C-240 to
completely cross fade from one scene to another scene.
14) 2- Speed Slider: to adjust the chase rate in Auto Mode
15) Faders ( 1 – 8 ): to adjust the output level from 0 – 255 or the intensity from 0% ­ 100% of each channel
(2)
2
REAR CONTROL PANEL:
16)
Midi In:
to receive MIDI data.
17) DMX Polarity Select: make sure Polarity of your fixture and set the SCENEMASTER C-240 to the proper polarity.
18) DMX Output: to send All DMX signals to fixture or powerpacks / dimmers.
19) DC Input: to supply a DC 9 – 12v power, 300 mA minimum
20) ON / OFF switch
3 - OPERATION INSTRUCTION:
Standard DMX 512 Addressing Dip Switch Setting: Each Dip Switch has an address based on
Binary code
Dip Switch number: 1 2 3 4 5 6 7 8 9 DMX Value: 1 2 4 8 16 32 64 128 256
Select the address wanted: by adding the total of Dip Switches
on.
(note)
Dip switch # 10 is not used with DMX normally for selectable functions, i.e. master/slave or sound activation etc. Each of the 12 fixtures is assigned 16 Channels (whether you are using all those channels or not . The dip switches on your fixtures are set as per the diagram on next page.
(3)
2 3
3
2
1
446 7 81 5
5
7
8
9
10
11
12
MIDI
METEOR-KLS
C-240
Program
Music
Bank-Copy
0.i /Sec.
10 Min
SPEED
FADE TIME
30 sec.
0
Scenes
PAN(9-19)
TILT(10-20)
RECORD
FINE MODE
DELETE
AUTO
TAP DISPLAY
BANK
BLACKOUT
CHASE 1
CHASE 4
CHASE2
CHASE 5
CHASE 6
HEATING ELEMENT
FOG
MACHINE
PAGES
A
PAGE
SELECT
B
Scanners Channels Dip Switches ON
Fixture 1 1 - 20 1
Fixture 2 21 - 40 1, 3, 5 Fixture 3 41 - 60 1, 4, 6 Fixture 4 61 - 80 1, 3, 4, 5, 6 Fixture 5 81 - 100 1, 5, 7 Fixture 6 101 - 120 1, 3, 6, 7 Fixture 7 121 - 140 1, 4, 5, 6, 7 Fixture 8 141 - 160 1, 3, 4, 8 Fixture 9 161 - 180 1, 6, 8 Fixture 10 181 - 200
1, 3, 5, 6, 8
Fixture 11 201 - 220 1, 4, 7, 8 Fixture 12 221- 240 1, 3, 4, 5, 7, 8
note:
When addressing your fixtures, use the starting addresses used in this instruction manual, not the addressing found in your fixture manual. (every thing in groups of 20)
SCENE PROGRAMMING:
1) Press and HOLD PROGRAM BUTTON for three (3)
seconds to activate PROGRAM Mode. The LCD next to “PROGRAM” blinks. This indicates the program has been started.
2) Select the fixture to program by pressing any or all the scanner buttons 1 - 12.
3) Adjust / move the Faders / sliders to the desired output levels for all channels (i.e., color gobo, pan and tilt, etc.) of the fixture(s) you selected. Press PAGE SELECT A/B if the fixture has more then 8 channels. When selecting from page A to B, you have to move the sliders to activate the channels.
4)
If you have set the fixture to its correct position, color gobo and you wish to program another fixture – Press the Scanner button you have just finished adjusting. This will hold that fixture and its values in its final configuration. Select another fixture by pressing the target Scanner Button and proceed to adjust / set and change to the settings of your liking of fixture two
5) Repeat Steps 2 and 3 until you have set the fixture to its correct position
(4)
6) When all the fixtures you want to be programmed are in there correct position. Press the MIDI / ADD button
7) Select the desired Bank to store scene using the UP and DOWN bank select button. There are 30 BANKS you can store up to eight scenes per BANK. For a total of 240 Scenes.
8) Then Press the SCENE BUTTON 1-8 to store the SCENE. All LED’s will flash 3 times. The LCD Screen will display the BANK and the SCENE where your SCENE was stored.
9) Repeat Steps 2-8 to record all your desired SCENES. You can copy the settings from one Scanner button to another in case you want to add more fixtures to your show. Just press and HOLD the SCANNER Button you want to copy. Then press the Scanner Button you want to copy to.
10) To exit PROGRAMMING Mode – Press and HOLD the
PROGRAM
button for 3 – 5 seconds. (when you exit the Programming, the BLACKOUT LED is on. Press BLACKOUT Button to disable BLACKOUT function
SCENE EDITING:
This function allows you to make changes in an already programmed scene.
1) Press the PROGRAM button for three seconds to enter the
Program mode.
2) Use the BANK UP and DOWN button to select the bank that stores the scene you would like to edit.
3) Select the Scene you want to edit by pressing the SCENE button.
4) Use the faders / sliders to make your changes.
5) Press the MIDI / Add button then followed by the SCENE
Button that corresponds to the scene you selected earlier (otherwise you might accidentally record over an existing scene).
SCENE COPY:
This function allows you to copy the setting of one scene to another.
1. Press the PROGRAM button for three seconds to enter the Program mode.
2. Use the BANK Up and Down to locate the bank that has a. that particular scene in it.
3. Select the desired SCENE you want to copy by pressing the
SCENE Button.
4. Use the BANK buttons UP and DOWN to select the Bank
where you want the to store the copied SCENE.
5. Press MIDI / Add button followed by the SCENE button where
you want to copy to.
3.
SCENE DELETE:
This function will rest all the DMX channels incorporated within a SCENE to a DMX value of 0.
1) Select the desired SCENE you would like to delete.
2) While Pressing and Holding AUTO / Del. Press the SCENE
button (1 – 8) you want to delete.
3.
ERASE ALL SCENE:
This will ERASE all SCENES in ALL BANKS. All SCENES are reset to DMX value zero (0). Make double sure this is really what you are wanting to do
1) Press and hold down PROGRAM and BANK Down buttons
while turning power off.
2) Re-connect POWER. All SCENES should be erased.
NOTE: Once you have successfully erased all SCENES, there is no way to retrieve them.
3.
COPY A BANK
:
This function enables you to copy the setting of one BANK to another BANK.
1) Press and HOLD the PROGRAM Button for 3 seconds to activate the PROGRAMMING Mode.
2) Select the BANK you want to copy.
3)
Press and Release the
MIDI / Add button.
4) Select the BANK into which you want to copy to.
5) Press the MUSIC / BANK-Copy Button. The LCD Display
will flash momentarily to indicate the process / copy has been completed.
(6)
3
DELETE A BANK:
1)
Press and
HOLD
the
PROGRAM
Button for 3 seconds to
Activate the PROGRAM Mode.
2) Select the BANK to be deleted.. Press AUTO / Del and MUSIC / Bank Copy at the same time to delete the BANK. The LCD will flash momentarily to indicate it has been successfully deleted.
3
CHASE PROGRAMMING:
You must already have programmed SCENES before you can program any chases.
1) Press and HOLD the PROGRAM Button down for three (3) seconds to enter the PROGRAMMING MODE
2) Choose any CHASE ( 1 – 6 ) to be programmed.
3) Select the desired SCENE from any of the BANKS. SCENES run in the same order as they are entered into the PROGRAM CHASE.
4) Pre the MIDI / Add Button. All the LED’s will FLASH three (3) times.
5) Repeat steps 3 and 4 as many times as you want. You can
record up to
240 SCENES
in one
CHASE.
6) When you are finished PROGRAMMING a CHASE – PRESS and HOLD the PROGRAM Button for three (3) seconds.
3
COPY A BANK TO A CHASE:
1. Press and HOLD the PROGRAM Button for three (3)
Seconds to enter the Programming Mode.
2. Select the BANK of SCENES you wish to copy.
3.
Select the CHASE to which you want to copy the bank of SCENES. Press the MUSIC / BANK-Copy Button. The LCD Display will flash momentarily to indicate the process / copy has been completed.
4. Press MUSIC / Bank-Copy and MIDI / Add at the same
time. The SCENES of the BANK are now copied into the CHASE.
5. Press and HOLD the PROGRAM Button for three (3)
seconds to exit the Programming Mode.
3
EDITING CHASES:
This feature allows you to add / delete SCENES from an
already existing CHASE.
1) Press and HOLD the PROGRAM Button down for three (3)
Seconds to enter the Programming Mode.
2)
Select the
CHASE
(1-6) to which you want to add a step.
3) Press TAPSYNC / Display and the LCD shows the SCENE and the BANK. That is the BANK containing the SCENE you want to add to the CHASE.
4) Press TAPSYNC / Display again and the LCD shows the CHASE that you have selected to add to.
5) Use the UP or DOWN Buttons to scroll through the CHASE to reach the step AFTER which you wish to add.
6) Press MIDI / Add – the LCD will read one step number
higher.
7) Press the SCENE Button you wish to add.
8) Press the MIDI / Add again to add the new step.
9) Press and HOLD the PROGRAM Button down for three (3)
seconds to exit the Programming Mode.
3
DELETING A STEP OR TWO IN A CHASE:
1) Press and HOLD the PROGRAM Button for three (3)
Seconds to enter the Programming Mode.
2) Select the CHASE (1-6) from which you want to delete a step (scene).
3) Press TAPSYNC / Display and the LCD shows the
CHASE you have selected.
4) Use the UP and Down Buttons to scroll through the
CHASE to reach the step (scene) you want to delete.
5) Press AUTO / Del and the SCENE will be deleted.
6) Press and HOLD the PROGRAM Button for three (3)
seconds to exit the Programming Mode.
3
DELETE CHASE ( all SCENES still available)
1) Press and HOLD down the BANK Down and AUTO / Del.
while turning power off.
2) Reconnect the Power and the CHASES should all be
deleted
(8)
3
RUNNING SCENES:
MANUAL RUN SCENES
1) When the power is first turned on, the unit is in a MANUAL
Scene mode.
2) If in the Program Mode – Press and Hold the PROGRAM Button for three (3) seconds. The
Program LED
will go out.
The SCENEMASTER is now in its MANAUL Mode.
3) Be Sure that the AUTO and MUSIC Button LED’s are off.
4) Select the BANK – using the UP or DOWN Button that stores the SCENES you want to run.
5) Press the SCENE Button to run the SCENE you have
selected.
3
RUNNING SCENES:
AUTO RUN SCENES:
This function will run a BANK of PROGRAMMED
SCENES in a sequential loop.
1) Press AUTO / Del once to activate the AUTO RUN mode.
2) Use the UP or DOWN BANK Button to select a Bank of SCENES to run.
3)
Now you can use the
SPEED
and
FADE
sliders to adjust
the SCENES to your liking
NOTE:
The FADE setting should never be slower then the
SPEED setting or the SCENES will not be completed.
4) You can change the BANKS “on the fly” by pressing the UP or DOWN BANK Buttons.
3
RUNNING SCENES:
MUSIC RUN SCENES
1) Press the MUSIC / Bank-Copy Button and the Corresponding indicator light will come on in the LCD.
2) Select the desired BANK that stores the SCENES you
want to CHASE by using the UP or DOWN Button
3
RUNNING SCENES:
MIDI RUN SCENES
1) Select BANK to run SCENES using MIDI – in MANUAL /
Auto or MUSIC Run Mode.
1) Select BANK to run SCENES using MIDI – in MANUAL / Auto or MUSIC Run Mode.
3
RUNNING CHASES:
MANUAL RUN CHASES:
This function will enable you to manually step through a selected CHASE.
1) Press and HOLD the PROGRAM Button for three (3)
seconds to enter the Programming Mode.
2) Start a CHASE by selecting one of the six (6) CHASE
Buttons.
3) Press the TAP SYNC Button. Each time you press the
button, you will step through the CHASE.
4) Use the BANK Select Button to scroll through the CHASES.
5) Press and HOLD the PROGRAM Button for three (3)
seconds to exit the Programming Mode
3
RUNNING CHASES:
AUTO RUN CHASES:
1) Press ANY or all of the 6 CHASE Buttons to select the
desired CHASE.
2) Press and Release the AUTO / Del. Button. The
corresponding LED will flash.
3) Adjust the FADE Time and SPEED to your desired setting.
The
CHASE
will run according to your settings.
4) You can override the Speed and Fade time by tapping the TAP SYNC / Display button three (3) times. Then the CHASE will be run based on the time interval of your taps.
NOTE A: Never adjust the FADE TIME slower then the SPEED
setting. Otherwise your CHASES will not be completed
before a new SCENE is sent
NOTE B: If you wish to include all the CHASES, Press AUTO / Del. before selecting a CHASE.
3
RUNNING CHASES:
MUSIC RUN CHASES:
1) Press one of the six (6) CHASE Buttons to select the
CHASE desired. Press and Release the MUSIC / Bank-Copy Button
2) The corresponding LED will FLASH in the LCD.
3) The CHASE will now run via the Sound / Music.
NOTE: When you exit a CHASE by Pressing the CHASE Button, the Controller will automatically run the
SCENES that are in the last bank accessed. To stop the movements of the light, either use the BLACKOUT button or Press MUSIC if in the Music Mode or in the AUTO Mode.
3
MIDI CHANNEL SETTING
MIDI RUNNING
1) Press and HOLD the MIDI / Add Button. The third and Fourth digits on the LCD display will FLASH – indicating MIDI Mode.
2) Use the UP or Down Buttons to select the Midi channel
(1 – 16) you would like to use / run.
3) Press and Hold the MIDI / Add Button once more to end
MIDI mode
3
MIDI CHANNEL SETTING
NOTE “ON”: RECEIVE NOTE “ON” SIGNALS TO EXECUTE
CORRESPONDING FUNCTIONS
THE SCENEMASTER RECIEVES ONLY MIDI NOTES AND YOU MIGHT WANT TO TRANSPOSE YOUR KEYBOARD TO FIND THE PROPER MIDI NOTE.
ASSIGNING PAN & TILT CHANNELS TO THE JOYSTICK
1) Press “Program” button for 2 seconds to enter Program Mode (LED flashes). Turn off BLACKOUT LED
2) Press “FINE + MODE, (together- twice) it will Display SET 00 00 Up FI CH
3) Press SCANNER Button, to select fixture assigning
4) Adjust the slider on SPEED to Channel 1
5) Adjust the slider on FADE TIME to X (almost to the top).
6) Press Midi/Record (one button) to confirm the PAN on Ch.1
7) Adjust the slider on SPEED to channel 2 (or whatever)
8) Adjust the FADE SLIDER to read Y
Finished – Press FINE + MODE to exit
TROUBLE SHOOTING / OFTEN ASKED QUESTIONS:
COLORS DON’T RESPOND WHEN FADERS ARE MOVE
MAKE SURE DMX ADDRESS IS CORRECT / DIP SWITCHES IF XLR CABLE IS MORE THEN 30 METERS (100FT), CHECK TO SEE IF TERMINATED CORRECTLY.
MIRRORS DON’T RESPOND WHEN SLIDERS ARE MOVED
MAKE SURE DMX ADDRESS IS CORRECT / DIP SWITCHES
MAKE SURE SPEED IS ADJUSTED, IF AVAILABLE FOR
FASTER MIRROR MOVEMENT. NOT ALL UNITS HAVE SPEED ADJUSTMENT
IF XLR CABLE IS MORE THEN 30 METERS (100FT), CHECK TO SEE IF TERMINATED CORRECTLY.
SCENES DON’T RUN AFTER RECORDING THEM
MAKE SURE TO PRESS MIDI / ADD BUTTON BEFORE
PRESSING SCENE BUTTON. LED’s SHOULD FLASH AFTER PRESSING EACH SCENE BUTTON. BE SURE YOU ARE IN THE CORRECT BANK THAT THE SCENES WERE RECORDED IN.
SCENES DON’T RUN CORRECTLY AS RECORDED
MAKE SURE ALL FIXTURES WERE RECORDED IN SCENE MAKE SURE YOU ARE IN THE CORRECT BANK THAT THE SCENES WERE RECORDED IN
CHASES DON’T RUN AFTER RECORDING THEM
MAKE SURE TO PRESS THE MIDI/ADD BUTTON AFTER
PRESSING THE SCENE BUTTON. LED SHOULD FLASH AFTER PRESSING MIDI / ADD.
BE SURE YOU ARE IN THE CORRECT CHASE THAT HAS
THE STEPS RECORDED IN
IF IN AUTO MODE – DID YOU ADJUST SPEED AFTER
SELECTING AUTO
FADE TIME IS TOO LONG FOR SPEED SELECTED
FIXTURES AREN’T DOING ANYTHING
HAVE YOU READ THIS MANUAL COMPLETELY AND
FOLLOWED ALL THE RECORDING STEPS FOR SCENES AND CHASES
DID YOU SET YOUR DIP SWITCHES ACCORDING TO THIS
MANUAL
ARE ALL UNITS PROPERLY CONNECTED WITH POWER
ON AND PROPERLY CONNECTED VIA DMX.
EC DECLARATION OF CONFORMITY: We declare that this product complies with the following specifications and bears CE mark in accordance with the provisions of Electro- Magnetic Compatibility (EMC) Directive 89/336/EEC EN55014-1:1994, EN61000-3-2:1995, EN61000-3­3:1995EN55014-2:1997CATEGORY ll EN61000-4-2:1995, EN61000-4-3:1995, EN61000-4­4:1995EN61000-4-5:1995, EN61000-4-6:1995, EN61000-4-11:1994HARMONIZED STANDARD EN60598-1:1993 Safety of Household and similar electrical appliances Par 1: General Requirements Following the provisions of the Low voltage Directive 73/23 EEC and 93/68/EEC
FOR TECHNICAL HELP / SUPPORT
MLSC Inc.
MLSC Inc.MLSC Inc.
MLSC Inc.
8000 Madison Pike, Madison, Alabama 35758
Tel (256) 461–8000 Fax: (256) 461–7708
Website: meteor-global.com e-mail: sales@meteor-usa.com
Loading...