Meteor ProMover P64 User Manual

P64 MOVING YOKE

USER MANUAL / OPERATION INSTRUCTION

ProMover P64 MOVING YOKE FIXTURE

Thank you for purchasing this truly unique
It is a fixture that is steadily getting more and more recognition and gaining popularity in the Theatrical Lighting Industry
as a “must have unit”. It was first introduced at the Orlando 2005 LDI show. The simplicity of the fixture is one of its truly
unique qualities. The efficiency and accuracy is the other two main features. The ProMover HPL 575 is capable of using
a variety of different lenses, depending on your specific needs, shapes and angles.

ProMover P64 MOVING YOKE FIXTURE

ProMover P64 MOVING YOKE FIXTUREProMover P64 MOVING YOKE FIXTURE

FEATURES:

4 or 6 channels of DMX

Built in Dimmer - controlled via DMX – full range
2 Variable Fans speeds via DMX
8 or 16 bit Resolution- Pan and Tilt

Uses the Any 500w or 1000w PAR 64 LAMP
LCD Display for DMX setting.
Various on board setting routines
Normal or Inverted Digital LCD Readout
Blue LED DMX signal input indicator
Flight Case – (optional –only available with 4-pack deal)

DMX CHANNELS:

Channel 1 – DIMMER – Built in to Channel 1. From 10 to 250 as a variable brightness to

Channel 2 –

DMX value (0 – 255)

Channel 3 –
Channel 4 –
Channel 5 –
Channel 6

FAN SPEEDS – Variable speeds from 0 – 126 (full speed)

STROBE / FLASH – The lamp will now be able to strobe / flash as you increase the

PAN
TILT
FINE ADJUST PAN – (16 BIT - if desired)

–

FINE ADJUST TILT - (16 BIT

– if desired

)

SAFTY FEATURES:

• Lamp change accessibility has been made so that it will be easier to replace a blown or broken lamp

• Wire mesh added to prevent lamp from falling or blown lamp going all over

• Your choice of either 8 bit or 16 bit resolution via LED DISPLAY

• Heavy Duty Flight Case – will now be available in package deals of 4 heads

• DMX Cables can be easily stored inside FLIGHT CASE during shipping:

• Safety cable

LCD SETTING / BUTTONS:

M/C – Menu Clear – changes LCD to different functions: set-ups / enables/menu clear.
UP - indicated by an arrow pointing up. Ascends -Raises values
DN - Indicated by an arrow pointing down – descends – lower values

ENTER - When you get to the function you want to test / use / or demo. Press Enter.

LCD MENU OPTIONS:

ADDR: Setting the starting address (Base address) of all fixtures being used

INIT. As soon as unit is powered up. The LCD screen flashes while it is going through all its

DISP: Visually normal Digital reading while sitting on floor or Tabletop.
(If you are going to be looking at the LCD while it is on the floor on a table with the light

Buttons beneath LCD puts you in a Directive Mode;

4

(note: the LCD Display can be either normal or inverted depending on how unit is
mounted. This will be determined if you change it in the NDSP mode)

“DMX resets” and Start -up procedures

aiming towards the ceiling.). If “off” display will not be seen

from

METEOR Inc.

1

NDSP: Inverted Digital readout - used while unit is mounted on truss or ceiling.

(if you are going to be looking at the LCD display while unit is hanging down – it is

recommended that you invert the LCD screen read out so you can look at it normal)
TALL: Test all channels of unit. If you want to test all channels. Press Enter.
(LCD changes to read –

CH01 – press Enter. Channel 1 (lamp and fan channel) will

start to come up in brightness and the fans will increase in speed to cool fixture.

Press Black UP button. LCD changes to

CH02. Press Enter. Lamp will start to flash and

strobe.

Press Black UP button. LCD changes to

CH03. Press Enter. Fixture will run through it

full PAN capability.

Press Black UP button. LCD changes to

CH04. Press Enter. Fixture will run through its

full TILT cycle.

Press Black UP button. LCD changes to

Press Black UP button. LCD changes to

Press

Black button to exit this test mode.

M/C

CH05. Press Enter. Does fine adjust – PAN.
CH06. Press Enter. Does fine adjust – TILT.

TLMP: Time of usage on lamp. Press Enter. Fixture will start to come up and fans will increase

in speed for maximum cooling
RSET: Unit resets itself to factory settings. TEST
Press Enter
DEMO: Unit runs it programs in a demo mode. 3 options: O
OFF – Fixture to be controlled by lighting controller
SLAV – subordinate – daisy chained – inline with controller
AUTO – runs automatically
Press Enter
TEST: Specific channel you wish to test.
Press Enter.
Y DIR: Set either clockwise or counterclockwise response. Individual channel test runs

a full range of the Tilt Function (“Y” reverse) – Mirror image if need be.
Press Enter.
X DIR: Set either clockwise or counterclockwise. Individual channel test runs a full

range of the Pan Function (“X” reverse). Mirror image if need be.
Press Enter.

NDST

DISP
TALL
LAMP

LAMP INSTALLATION:

- Disconnect Power
inside.

- On the back of the unit. Locate two (2) Spring clips. Push forward – the back will hinge open.

- Remove 8” retaining ring.

- Carefully insert Par 64 lamp of choice into / onto 4 long Teflon holders.

- Push lamp forward enough to the front brace.

- Position retaining clip back around the lamp to hold in place.

- Carefully plug the Ceramic lamp socket onto lamp. As far as it can.

Note:

- Hold Back the two spring loaded clips and shut back of unit. Lock in place.

- Move unit head up and down to hear if there is any noise. If no noise, it is correctly seated.

NDS T

DISP

TALL

LAMP

Replacing or installing the lamp.

from fixture. If lamp is broken, make sure no pieces of glass are rattling around

If not seated correctly, this could cause the socket to come loose from the lamp.

2