regularly (short FLASHES) every 0.8 seconds to signal that the system is
s on when there is an external power supply
Yellow LED: This light comes on briefly every time the central unit
infrared sensor detects a movement, both when the alarm system is
ntral unit has an alarm memory that signals any alarms occurring
If the Red LED remains on after disarming the central unit and 18
seconds has elapsed, an alarm has been triggered and the Red LED will
If no alarms have been triggered, the red LED on the central unit will go
that supplied you
with the alarm system, carry out the following procedures to make it
1) Using the remote control supplied, arm and disarm the central unit
several times (press the button consecutively 16 times, waiting a few
ne operation and the next) until the central unit emits
2) Press the button on the new transmitter within 8 seconds until the
rised, including
4) Once all the remote controls have been memorised, wait about 8 sec.
for the central unit to exit the remote control memorising mode. From
above
It is possible to block operation of any remote control that has been lost
or stolen: in this way the safety of your alarm system is ensured, since
o disable any lost transmitters, repeat the
operation from point 1 to point 4 in the previous section, using all the
Any transmitters that have been lost or that will not be used in this phase
Due to the normal discharge of the rechargeable batteries in the parts
with battery back up, the battery charge may be low at the time of
installation. Therefore keep the product powered for at least 24 hours
For any clarification on using the system, please do not hesitate to call
your area dealer who should affix his stamp below and/or give the
HomeAlarm DivisionHomeAlarm Division
C11C11
END USER INSTRUCTIONSEND USER INSTRUCTIONS
A MANUAL TO AVOID MISTAKESA MANUAL TO AVOID MISTAKES
Congratulations for having chosen an alarm system from the HOME alarm
division of MetaSystem.
These instructions are designed to help the owner of a Meta System
HOME ALARM to use the system correctly by carefully following the stepby-step explanations on the following pages.
REMOTE CONTROL TRANSMITTERREMOTE CONTROL TRANSMITTER
This transmitter makes it possible to switch the alarm system on and off.
EMERGENCY KEYEMERGENCY KEY
With these keys it is possible to fully isolate the C11 unit and therefore
deactivate the alarm system.
Caution: store these keys in a safe place.
ADHESIVE LABELSADHESIVE LABELS
Stick the adhesive labels on the entrance door or on windows where they
can easily be seen from the outside, as an additional deterrent.
OPERATIONOPERATION
In the case of an attempted break-in detected by the system’s infrared
sensor, the unit will emit a number of beeps at low volume as a prealarm (for 3 seconds), then it will activate its powerful siren for one alarm
cycle of 50 seconds.
SYSTEM DISARMEDSYSTEM DISARMED
When the system is disarmed, the status is reported by different LED
signals:
-The Green LED present on the central unit indicates, “Power on”. If this
LED is off (i.e. no power), the central unit is still operative and functions
thanks to the rechargeable internal back up batteries.
- Every time something moves within the range of the infrared sensor on
the Central unit, Central unit, a Yellow LED indicates that the object has been
detected. However, if objects pass in front of the sensor very frequently,
the sensor may not indicate all of them since it will enter immunity mode
for a few moments.
SYSTEM ARMEDSYSTEM ARMED
-- The flashing Red LED on the central unit indicates that the system is
armed. However, it will only be able to generate an alarm 25 seconds
after being armed, if there is an intrusion.
USER INSTRUCTIONSUSER INSTRUCTIONS
ARMINGARMING
Press and release the remote control button to activate the alarm
system. The unit will emit two low-volume signals (BEEPS) and the red
light will flash. After 25 seconds, the system is active and ready to go into
operation in the event of a break-in.
DISARMINGDISARMING
Press and release the remote control button to deactivate the alarm
system. The unit will emit a single long BEEP and the red light will go out.
If the Red light does not go out and the unit emits 10 beeps close
together after approximately 18 seconds, it means that during your
absence there has been at least one alarm (see the section ALARM
MEMORY for a full explanation).
PANIPANIC ALARMC ALARM
Keep the remote control button pressed for approximately 6 seconds. An
alarm cycle lasting 15 seconds will be generated that, once activated,
cannot be stopped so it is necessary to wait for the end of the cycle.
SIGNALSSIGNALS
CENTRAL UNITCENTRAL UNIT
- Red LED: During the first 25 seconds after switching on, this light will
flash in inverted mode (short PAUSES). After this time it will flash
WHAT YOUR ALARM SYSTEM INCLUDESWHAT YOUR ALARM SYSTEM INCLUDES
WHAT YOUR ALARM SYSTEM DOESWHAT YOUR ALARM SYSTEM DOES
ready to trigger an alarm.
- Green LED: This light i
(mains voltage or 12V).
-
armed or disarmed.
CENTRAL UNIT ALARM MEMORYCENTRAL UNIT ALARM MEMORY
The ce
during your absence.
flash accordingly.
The signals continue until the unit is switched on again.
out when the system is disarmed.
OPERATING INSTRUCTIONSOPERATING INSTRUCTIONS
ADDITIONAL REMOTE CONTROLSADDITIONAL REMOTE CONTROLS
After purchasing a new remote control from the centre
operative.
seconds between o
3 consecutive BEEPS.
central unit confirms reception by emitting 3 BEEPS.
3) Repeat step 2 for each further transmitter to be memo
those, which were already memorised.
this moment onwards, only the transmitters memorised in the
phase will be able to command the central unit.
EXCLUDING REMOTE CONTROLSEXCLUDING REMOTE CONTROLS
only you can turn it off. T
transmitters remaining.
will be automatically inhibited.
CAUTICAUTI ONON
before testing the back up.
TECHNICAL SERVITECHNICAL SERVICESCES
WHO TO CALLWHO TO CALL
particulars of the person to contact:
NAMENAME
____________________________________________________________________________________________________________________
PHONEPHONE
____________________________________________________________________________________________________________________
Installer’s stamp
When transmission of all the available remote controls is completed,
wait approximately 8 seconds; the central unit will then exit from the
From this moment on, only transmitters that have been enabled can
brackets as shown in Fig. 3 and attach them to the wall
in the
If necessary, make the following connections as shown in the general
unit in the OFF position and the
n made, position the connection cover in
tapping screws as shown in Fig. 2.
Then attach the control unit onto the bracket using the 2 socket head
a) Activate the central unit by pressing the button on the remote control.
b) Within 25 seconds from activation, simulate an alarm by tripping the
cate that the alarm
signal has been received. At this point, you have 25 seconds to retest the
c) Wait 25 seconds and put the unit into alarm status by simulating the
tripping of the PIR sensor. The unit will emit several beeps (lasting about
3 seconds), after which the internal siren goes into operation for about
Keep the keys supplied with the alarm central unit in a safe place. If both
keys are lost, it is not possible to remove or deactivate the alarm central
HomeAlarm DivisionHomeAlarm Division
C11C11
FITTING INSTRUCTIONSFITTING INSTRUCTIONS
Technical characteristicsTechnical characteristics
Power supply: -------------------------------------230 - 240 V AU.50 - 60 Hz or 12 V
DC (SELV)
Battery autonomy time: ---------------------C11: 12 hours
Dimensions C11: --------------------------------105 x 110 x 115 mm
Alarm cycle duration: -------------------------50 seconds
Maximum alarm cycles per channel: 6
Alarm relay capacity: --------------------------C11: 10A
Sound output: -------------------------------------C11: 118 dB
Lithium battery powered remote controls with over 4 million possible
codes.
How to InstallHow to Install
Please refer to the following points step by step.
1 1 - Where to InstallWhere to Install
-Choosing the correct location is very important so please carefully
consider the following points:
-Since the central unit requires a 230 V or 12 V power supply, try to
install the unit as close as possible to an outlet;
-The siren must be able to sound freely and must not be placed behind
obstacles that could dampen the sound;
-The C11 can either be fitted to a wall or ceiling; the higher it is placed
the greater the range it will cover (see fig. 1);
-The P.I.R. sensor must be fitted facing the area to be protected and must
have a clear view without being obstructed by walls, curtains or
partitions;
-Do not turn the P.I.R. toward fireplaces or stoves (or any source of
excessive heat) or toward the exterior of windows or glass walls;
CAUTION: CAUTION: to guarantee that the memorisation or cancellation of
remote controls takes place correctly, make sure that the alarm system
has been powered for at least 24 hours (in order to charge the internal
batteries) then disconnect it from the power source before proceeding.
2 2 -- Remote cRemote control memorisationontrol memorisation
A coded remote control is used for carrying out all the various operations
of activation, deactivation and so on.
One of these is supplied with the central unit, and the following steps
must be carried out to make it operative:
Switch on the alarm central unit (ON position) by turning the key on the
rear of the C11 central unit clockwise.
The central unit will emit a low volume BEEP:
Press the remote control button and keep it pressed until the unit emits 3
brief beeps and the red LED begins to flash. Once the button is released,
after about 10 seconds the control unit will emit a prolonged beep to
indicate that storing has been accomplished.
2.1 2.1 -- Memorisation of additional remote controls Memorisation of additional remote controls
(optional)(optional)
If additional remote controls are purchased, the central unit must
memorize them in order to make them operative. To do this, proceed as
follows:
Step 1. Using the original remote control provided with the central unit,
carry out a series of activations/deactivations (press the button 16 times
consecutively, waiting a few seconds between one operation and the
next), until the central unit emits 3 consecutive beeps.
Step 2. Press the button of the new transmitter within 8 seconds until
the central unit emits 3 BEEPS to indicate that the signal has been
received. At this point, the new transmitter has been added to the list of
those enabled.
-Step 3. Repeat Step 2 for each additional transmitter that you want to
enable, including “old” ones. If you repeat Step 2 with a transmitter that
has already been enabled, the central unit still emits 3 beeps, but this
operation has no utility.
-
remote control storing phase.
control the unit.
3 3 -- Installing the C11 Installing the C11
-Join the two halfor ceiling using the screws and the plastic screw anchors provided
kit (make two Ø 7 mm holes) (see fig. 4).
wiring diagram, with the key of the C11
220 V mains supply disconnected.
-When all connections have bee
its seat and secure it using the 2 self-
screws as shown in Fig. 4.
CAUTIONCAUTION
§ The product should be connected to the domestic supply
(230v).
§ All electrical connections must be made by qualified
personnel
§ Note! Risk of electric shock! Always disconnect the electric
power source by means of the main circuit breaker of the
domestic electricity supply (230v) before making any
connections.
§ The product contains rechargeable batteries, which must be
disposed of correctly and not together with domestic waste.
Use special recycling containers for differentiated waste
collection provided by your local authority.
4 - Final Final checkcheck
The unit emits 2 beeps and the Red LED flashes.
PIR sensor. The central unit will emit one beep to indi
PIR sensor.
50 seconds.
PLEASE NOTE:
unit without causing irreparable damage.
Loading...