MetalTech WALL HAULER I-BMD3031R, WALL HAULER I-BMD3031P, WALL HAULER I-BMD3031PK, WALL HAULER I-BMD3031RK Operational Safety And Assembly Instructions

READ THESE INSTRUCTIONS CAREFULLY BEFORE USING THIS PRODUCT.
KEEP THIS MANUAL HANDY FOR FUTURE REFERENCE.

Picture may differ from actual product

ENGLISH

FRANÇAIS

ESPAÑOL

ENGLISH

FRANÇAIS

ESPAÑOL

OSHA ANSI CSA

CONFORMANCE TO MEETS CONFORMITY TO

2

YEAR

WARRANTY

MODELS: I-BMD3031R
I-BMD3031P
I-BMD3031RK
I-BMD3031PK

WALL HAULER™ SERIES 3000

DRYWALL CART

OPERATIONAL SAFETY AND
ASSEMBLY INSTRUCTIONS

OPERATIONAL SAFETY

METAL CONDUCTS ELECTRICITY:

Do not use this equipment where contact may be made with power lines or other live electrical circuits.

DO NOT OVERLOAD:

This Drywall Cart is designed to support a maximum load of 3,000 lb (1,361 kg)

FAILURE TO UNDERSTAND AND FOLLOW ALL SAFETY RULES AND ASSEMBLY INSTRUCTIONS
COULD RESULT IN SERIOUS INJURY OR DEATH.

READ BEFORE BEGINNING ASSEMBLY.

OPERATION AND SAFETY

All photos and drawings in this booklet are for reference purposes only. Refer to applicable

OSHA, ANSI or CSA codes and regulations for the proper use of this equipment.

2

LB / KG

MAX. 3,000 lb

(1,361 kg)

ALWAYS INSPECT
BEFORE USE

DRYWALL CART
MAXIMUM LOAD
CAPACITY:
3,000 lb (1,361 kg)

METAL CONDUCTS
ELECTRICTY

ACIDS ARE
CORROSIVE. DO
NOT EXPOSE UNIT
TO CORROSIVE
SUBSTANCES

UNEVEN WEIGHT
DISTRIBUTION COULD
CAUSE CART TIPPING

MUST BE USED ON A
FIRM SURFACE THAT
IS FREE OF PITS,
DEBRIS, HOLES OR
OBSTRUCTIONS.

UNIT SHALL ONLY BE
USED ON FIRM AND
LEVEL SURFACES

NEVER MOVE
A DRYWALL CART
WITH WORKER WITHIN

SUDDENLY
DROPPING OR
BOUNCING A LOAD
ON THE DRYWALL
CART MAY CREATE
AN EXCESS LOAD

Do not use this equipment if you are in poor health,

taking medications, drugs, or have been consuming
alcohol, all of which may impair your ability to work
safely on this product.

Always use this cart in conformity with local or national

legislation which applies.

Inspect before use. Do not use if damaged. Check for

missing parts.

Examine thoroughly to make sure Drywall Cart is set

up properly.

All components must be complete, functioning

properly and correctly assembled.

Any incomplete part, missing part, or ill-fitting part

should be replaced prior to use.

Use the right product for the job. Do not modify the

Drywall Cart and do not use the Drywall Cart for a
purpose for which it was not intended.

Do not exceed the maximum load capacity

of 3,000 lb (1,361 kg).

Always distribute objects in the Drywall Cart evenly,

and resting adequately on the handle bar. Uneven
weight distribution could cause Drywall Cart tipping.

Be aware of dynamic loading. Suddenly dropping or

bouncing a load on the Drywall Cart may create, for
a brief instant, an excess load, which may result in

damage to the product and/or personal injury.
This Drywall Cart must be used on solid flat surfaces.
This Drywall Cart must be used on a firm surface that

is free of pits, debris, holes or obstructions.
Acids are corrosive and can seriously affect strength.

Do not expose this Drywall Cart to corrosive

substances.
Never move a Drywall Cart with worker within.
Do not use powered devices to propel this Drywall

Cart. Use extra caution near operating machinery.
Do not modify this Drywall Cart or any of its

component.

ASSEMBLY INSTRUCTIONS

Engage the first handle bar (“C” shape) on the cart platform. With a rubber mallet, firmly hit each upper ends of
the handle, as shown in the figure below (1), make sure that the handle is fully inserted by verifying that holes of
the handle bar are aligned with those on the cart platform. Do not screw anything at this stage.

Join the top of the second handle bar (“H” shape) with the first handle bar installed, as shown in the diagram
below (2), do not screw anything at this stage. Engage the “H” handle bar on the cart platform. With a rubber
mallet, firmly hit each side of the central tube, as shown in the diagram below (2), make sure that the handle is
fully inserted by verifying that holes of the handle bar are aligned with those on the cart platform.

Put together the tops of both handle bars using two 3/4 in. barrel nut and two 1 in. carriage bolt supplied. Make
sure that everything is firmly screwed.

Fasten the assembled handle bar to the cart platform using four 2 in. hex bolts and nuts supplied. Make sure that
everything is firmly screwed.

Lay down the cart on its side to install casters. Firmly screw the casters under the cart using sixteen 3/8 x 1 in.
hex bolts and washers supplied.

3

1

2

3

4

5

THE USE OF A RUBBER MALLET IS RECOMMENDED TO
AVOID DAMAGE TO THE COMPONENTS OF THE CART.
(NOT INCLUDED)

ENGLISHENGLISH

2x

2x

16x

4x

4x

16x

BOX CONTENTS

QTY. PART CODE DESCRIPTION

2 VB-NB1/4X3/4Z 3/4 in. barrel nut
2 VB-BC1/4X1Z 1 in. carriage bolts
4 VB-B3/8X2Z 2 in. hex bolts

16 VB-B3/8X1Z 1 in. hex bolts

4 VB-N3/8Z 3/8 in. hex nuts

16 VB-WL3/8Z 3/8 in. lock washers

1 321116900 Cart platform
1 321117300 “C” handle bar
1 321117200 “H” handle bar
4 I-DCC8R Swivellings casters
1 I-DCCDL Directional lock
1 I-DCCWL

Caster brake

3

5

4

2

1

AVAILABLE OPTIONS

*

SEE YOUR RETAILER FOR DETAILS

PRODUCT CODE DESCRIPTION

I-BMDSP

Optional sliding coating, protects the surface
against abrasion

*Options not included, sold separately

Metaltech is a registered trademark of Metaltech-Omega inc.

DESIGNED IN CANADA / MADE IN CHINA

WWW.METALTECH.CO

1 800 363-7587

LAVAL, QUEBEC, CANADA H7L 3N6

Two-Year Limited Warranty

Metaltech-Omega Inc. guarantees this product against any material defect. Please return this product, freight prepaid, to Metaltech-Omega
Inc. At its own discretion, Metaltech-Omega Inc. will replace or repair this product and return it within a reasonable time. This warranty does
not cover any damage(s) caused by any incorrect or inappropriate use, care or maintenance. Proof of purchase must accompany the return.

Customer Service: 1 800 363-7587

Our customer service staff is available to help you. For help with product assembly, to report damaged or missing parts, or for any other
information about this product, please call our toll-free number.

KEEP THIS MANUAL FOR FUTURE REFERENCE

Keep this manual and the original sales invoice in a safe, dry place for future reference.

4