Metal Sales T-Armor User Manual
T-Armor™ Install Guide
The application and detail drawings in this manual are strictly for illustration purposes and may not be applicable to all
building designs or product installations. All projects should conform to applicable building codes for that particular area. It
is recommended to follow all building regulations and standard industry practices.
Metal Sales Manufacturing Corporation is not responsible for the performance of the roof system if it is not installed in
accordance with the suggested instructions referenced in this manual. If there is a conict between this manual and the
approved Metal Sales' erection drawings, the approved erection drawings are to take precedence.
Prior to ordering and installing materials, all dimensions should be veried by eld measurements.
Oil canning is not a cause for rejection. Oil canning can be described as the amount of waviness found in the at areas
of metal panels. Oil canning is an inherent characteristic of light gauge cold formed metal products, particularly those with
broad at areas. There are many factors which may contribute to oil canning that Metal Sales is not able to control. These
factors include: misalignment of the support system, over driving of fasteners used on the panels, stress (whether inherent
in the panel or induced), thermal expansion and contraction of the panel, material handling, width, gauge, length, color of
panels, and installation. (Reference Metal Construction Association "Oil Canning Position Paper" - Appendix A).
Metal Sales reserves the right to modify, without notice, any details, recommendations or suggestions. Any questions you
may have regarding proper installation of the T-Armor Series roong system should be directed to your Metal Sales representative, (see pages 2 and 3).
Consult Metal Sales for any additional information not addressed in this manual.
This manual is designed to be utilized as a guide when installing T-Armor roong system. It is the responsibility of the erector to ensure the safe installation of this product system.
SAFETY
STUDY APPLICABLE OSHA AND OTHER SAFETY REQUIREMENTS BEFORE
FOLLOWING THESE INSTRUCTIONS.
The installation of metal roof systems is a dangerous procedure and should be supervised by trained knowledgeable erectors. USE EXTREME CARE WHILE INSTALLING ROOF PANELS. It is not possible for Metal
Sales to be aware of all the possible job site situations that could cause an unsafe condition to exist. The erector of the roof system is responsible for reading these instructions and determining the safest way to install the
roof system.
These instructions are provided only as a guide to show a knowledgeable, trained erector the correct part
placement one to another. If following any of the installation steps would endanger a worker, the erector should
stop work and decide upon a corrective action.
Provide required safety railing, netting, or safety lines for crew members working on the roof.
Do not use the roof panel as a walking platform. The roof panels will not withstand the weight of a person
standing at the edge of the panel.
Do not stand on the roof panel until the panels have been attached.
METAL SALES BRANCHES
14
9
15
16
8
18
6
21
11
1
4
20
13
10
17
3
5
7
12
19
2
NOTE: Shaded areas represent regions served by each location.
*
Indicates Metal Sales branch manufactures T-Armor Series Panels
Metal Sales offers a complete line of metal roof, wall, and fascia panel systems for the commercial,
architectural, industrial, residential, and markets. Metal Sales offers over 75 profiles with a wide selection
of widths, colors, and gauges - new construction or retrofit.
2
© Metal Sales Manufacturing Corporation / Subject to change without notice 09/14
T-ARMOR
CUSTOMER SERVICE
1.) DENVER BRANCH
7990 East I-25 Frontage Road
Longmont, CO 80504
303.702.5440 Phone
800.289.7663 Toll Free
800.289.1617 Toll Free Fax
2.) JACKSONVILLE BRANCH
7110 Stuart Avenue
Jacksonville, FL 32254
904.783.3660 Phone
800.394.4419 Toll Free
904.783.9175 Fax
800.413.3292 Toll Free Fax
3.) JEFFERSON BRANCH
352 East Erie Street
Jefferson, OH 44047
440.319.3779 Phone
800.321.5833 Toll Free
440.576.9242 Fax
800.233.5719 Toll Free Fax
4.) INDEPENDENCE BRANCH
1306 South Powell Road
Independence, MO 64057
816.796.0900 Phone
800.747.0012 Toll Free
816.796.0906 Fax
5.) SELLERSBURG BRANCH
7800 State Road 60
Sellersburg, IN 47172
812.246.1866 Phone
800.999.7777 Toll Free
812.246.0893 Fax
800.477.9318 Toll Free Fax
6.) ROGERS BRANCH
22651 Industrial Boulevard
Rogers, MN 55374
763.428.8080 Phone
800.328.9316 Toll Free
763.428.8525 Fax
800.938.9119 Toll Free Fax
7.) NASHVILLE BRANCH
4314 Hurricane Creek Boulevard
Antioch, TN 37013
615.229.6570 Phone
800.251.8508 Toll Free
615.283.4283 Fax
800.419.4372 Toll Free Fax
8.) SPOKANE BRANCH
East 2727 Trent Avenue
Spokane, WA 99202
509.536.6000 Phone
800.572.6565 Toll Free
509.534.4427 Fax
9.) SEATTLE BRANCH
20213 84th Avenue, South
Kent, WA 98032
253.872.5750 Phone
800.431.3470 Toll Free (Outside WA)
800.742.7900 Toll Free (Inside WA)
253.872.2008 Fax
10.) NEW ALBANY BRANCH
999 Park Place
New Albany, IN 47150
812.944.2733 Phone
812.944.1418 Fax
11.) ROCK ISLAND BRANCH
8111 West 29th Street
Rock Island, IL 61201
309.787.1200 Phone
800.747.1206 Toll Free
309.787.1833 Fax
12.) DEER LAKE BRANCH
29 Pinedale Industrial Road
Orwigsburg, PA 17961
570.366.2020 Phone
800.544.2577 Toll Free
570.366.1648 Fax
800.544.2574 Toll Free Fax
13.) TEMPLE BRANCH
3838 North General Bruce Drive
Temple, TX 76501
254.791.6650 Phone
800.543.4415 Toll Free
254.791.6655 Fax
800.543.4473 Toll Free Fax
14.) WOODLAND BRANCH
1326 Paddock Place
Woodland, CA 95776
530.668.5690 Phone
800.759.6019 Toll Free
530.668.0901 Fax
15.) FONTANA BRANCH
14213 Whittram Avenue
Fontana, CA 92335
909.829.8618 Phone
800.782.7953 Toll Free
909.829.9083 Fax
16.) ANCHORAGE BRANCH
4637 Old Seward Highway
Anchorage, AK 99503
907.646.7663 Phone
866.640.7663 Toll Free
907.646.7664 Fax
17.) BAY CITY BRANCH
5209 Mackinaw Road
Bay City, MI 48706
989.686.5879 Phone
888.777.7640 Toll Free
989.686.5870 Fax
888.777.0112 Toll Free Fax
18.) DETROIT LAKES BRANCH
1435 Egret Avenue
Detroit Lakes, MN 56501
218.847.2988 Phone
888.594.1394 Toll Free
218.847.4835 Fax
888.594.1454 Toll Free Fax
19.) MOCKSVILLE BRANCH
188 Quality Drive
Mocksville, NC 27028
704.859.0550 Phone
800.228.6119 Toll Free
704.859.0157 Fax
800.228.7916 Toll Free Fax
20.) FORT SMITH BRANCH
7510 Ball Road
Fort Smith, AR 72908
479.646.1176 Phone
877.452.3915 Toll Free
479.646.5204 Fax
21.) SIOUX FALLS BRANCH
2700 West 3rd Street, Suite 4
Sioux Falls, SD 57104
605.951.0367 Phone
888.299.0024 Toll Free
TECHNICAL SUPPORT
TECHNICAL SERVICES
545 South 3rd Street, Suite 200
Louisville, KY 40202
502.855.4300 Phone
800.406.7387 Toll Free
502.855.4290 Fax
800.944.6884 Toll Free Fax
© Metal Sales Manufacturing Corporation / Subject to change without notice 09/14
3
TABLE OF CONTENTS
PAGE NO.General Information
Important Information ......................................................................................................... 1
Metal Sales Locations ........................................................................................................ 2
Customer Service ............................................................................................................... 3
Table of Contents .........................................................................................................4 & 5
Flashing Angle Chart ...................................................................................................... 6
Panel Profiles
Flat Panel Profile ................................................................................................................. 7
Pencil Rib Panel Profile....................................................................................................... 8
Minor Rib Panel Profile ....................................................................................................... 9
Striated Panel Profile ........................................................................................................ 10
Mesa Panel Profile ............................................................................................................ 11
Plank Panel Profile ............................................................................................................ 12
Accessory Profiles .................................................................................................. 13-16
Flashing Profiles ...................................................................................................... 17-23
Fastener Selection Guide ............................................................................................. 24
Fastener Technical Information
Physical Properties ........................................................................................................... 25
Pull Out Strength Values ................................................................................................... 26
Pull Over Strength Values ................................................................................................. 27
Testing Information
UL 580 Wind Uplift Informatioin ...................................................................................28-30
UL 263 Fire Resistance Rating ......................................................................................... 31
Testing Summary .............................................................................................................. 31
Section Properties and Load Tables
2
23/8" Aluminum Panel Properties ....................................................................................... 33
3" Steel Panel Properties .................................................................................................. 34
3" Aluminum Panel Properites .......................................................................................... 35
Handling Material
Receiving Material ............................................................................................................ 36
General Handling ............................................................................................................. 36
Mechanical Handling ........................................................................................................ 36
Manual Handling .............................................................................................................. 37
Storage
General ............................................................................................................................ 38
Storage on Roof ............................................................................................................... 39
Foot Traffic ................................................................................................................... 40
Curb Installation .......................................................................................................... 40
Field Cutting and Touch-up
Field Cutting ..................................................................................................................... 41
Touch-up Paint ................................................................................................................. 41
Design / Installation Considerations
Fastener Installation Technique ........................................................................................ 42
Condition of Substructure ................................................................................................. 42
Ventilation ........................................................................................................................ 43
Insulation .......................................................................................................................... 43
System Expansion / Contraction ..................................................................................... 44
Selection of System Components ................................................................................... 44
Factory Notching ............................................................................................................... 45
Installation Strategies/Directions ............................................................................... 46
Installation of Panel
Installation of Eave Flashing ............................................................................................ 47
Installation of Rake Angle .................................................................................................48
Installing First Panel ......................................................................................................... 49
Installing Panel Clips ......................................................................................................... 50
Endlapping of Panel ..................................................................................................... 48-51
Sidelapping of Panel ......................................................................................................... 53
Termination of Panel ........................................................................................................ 54
3
/8" Steel Panel Properties ............................................................................................... 32
4
© Metal Sales Manufacturing Corporation / Subject to change without notice 09/14
T-ARMOR
TABLE OF CONTENTS (cont.)
Seaming Panels .......................................................................................................... 55-56
Panel Removal and Replacement..................................................................................... 56
Installation Details
PAGE NO.
Post Hung Gutter (floating) ............................................................................................... 57
Box Gutter w/ Offset Cleat (floating) ................................................................................. 58
Eave Transition - knee cap................................................................................................59
Eave (floating) ................................................................................................................... 60
Valley w/ Offset Cleat (floating) ......................................................................................... 61
Endlap .............................................................................................................................. 62
Rake ................................................................................................................................. 63
Rakewall............................................................................................................................64
Expansion Joint ................................................................................................................ 65
Endwall (fixed)...................................................................................................................66
Peak (fixed) ....................................................................................................................... 67
Ridge/Hip (fixed) ...............................................................................................................68
Post Hung Gutter (fixed) ................................................................................................... 69
Box Gutter w/ Offset Cleat (fixed) ..................................................................................... 70
Eave Transition - knee cap................................................................................................71
Eave (fixed) ....................................................................................................................... 72
Valley (fixed) ...................................................................................................................... 73
Endwall (floating)...............................................................................................................74
Ridge/Hip (floating) ...........................................................................................................75
Installation of Z-Closures ............................................................................................ 76
Hemming Detail ............................................................................................................ 71
Panel Turn-Up ................................................................................................................ 71
Z-Clsoure Bend .............................................................................................................. 71
Roof Penetrations
General Notes ................................................................................................................... 77
Installation Notes............................................................................................................... 77
Flashing Laps ................................................................................................................ 71
Care and Maintenance ................................................................................................. 78
Notes ....................................................................................................................... 79-80
© Metal Sales Manufacturing Corporation / Subject to change without notice 09/14
5
FLASHING ANGLE CHART
This chart should be used to determine the specied angle.
1
PROFILE/FLASHING
RIDGE
SSR RIDGE
VENTED RIDGE COVER
HIP
VALLEY
EAVE, ROOF CLEAT
EXTENDED EAVE
SCULPTURED EAVE
SSR SCULPTURED
HIGH SIDE EAVE
PEAK, ROOF CLEAT 89° 88° 85° 81° 76° 72° 67° 63° 60° 56°
/4:121/2:12 1:12 2:12 3:12 4:12 5:12 6:12 7:12 8:12
178° 175° 170° 161° 152° 143° *135° *127° *120° *113°
178° 177° 173° 167° 160° 154° 148° 143° 138° 134°
91° 92° 95° 99° 104° 108° 113° 117° 120° 124°
99° 98° 95° 91° 86° 82° *77° *73° *70° *66°
PITCH BREAK
HIGH SIDE PITCH BREAK
GUTTER DRIP
BOX GUTTER
91° 92° 95° 99° 104° 108° 113° 117° 120° 124°
91° 92° 95° 99° 104° 108° 113° 117° 120° 124°
PEAK "A" DIMENSION
3
2
/8" UTILITY SYSTEM 51/2" 51/2" 51/2" 55/8" 55/8" 53/4" 6" 61/8" 63/8" 65/8"
23/8" LOW SYSTEM 57/8" 57/8" 57/8" 6" 6" 61/8" 63/8" 61/2" 67/8" 71/8"
23/8" HIGH SYSTEM 67/8" 67/8" 67/8" 7" 71/8" 71/4" 71/2" 75/8" 8" 81/4"
3" UTILITY SYSTEM 61/8" 61/8" 61/8" 61/4" 61/4" 61/2" 65/8" 67/8" 71/8" 73/8"
3" LOW SYSTEM 61/2" 61/2" 61/2" 65/8" 63/4" 67/8" 7" 71/4" 71/2" 73/4"
3" HIGH SYSTEM 71/2" 71/2" 71/2" 75/8" 73/4" 77/8" 81/8" 83/8" 85/8" 9"
EAVE "A" DIMENSION
FLOATING SYSTEM 3" 3" 3" 3" 31/8" 31/8" 31/4" 33/8" 31/2" 35/8"
FIXED UTILITY SYSTEM 31/4" 31/4" 31/4" 31/4" 33/8" 33/8" 31/2" 35/8" 33/4" 37/8"
FIXED LOW SYSTEM 33/8" 33/8" 33/8" 33/8" 31/2" 31/2" 35/8" 33/4" 37/8" 4"
FIXED HIGH SYSTEM 43/8" 43/8" 43/8" 43/8" 41/2" 45/8" 43/4" 47/8" 51/8" 51/4"
ROOF CLEAT "A" DIMENSION
All SYSTEMS 3" 3" 3" 3" 31/8" 31/8" 31/4" 33/8" 31/2" 35/8"
6
*Note: Metal Sales standard flashing dimensions may not accomodate all situations, please inquire about custom flashings
for slopes 5:12 or greater.
© Metal Sales Manufacturing Corporation / Subject to change without notice 09/14
T-ARMOR
FLAt PAnEL PRoFILE
12" COVERAGE
23/8" or 3"
w/ CAp
C
23/8" RIB HEIGHt
GAUGES AcG PVDF BARE ALUM.
24 GA TA10141 TA101XX - 172 lbs
22 GA TA20141 TA201XX
20 GA TA30141 TA301XX
.032 AL
.040 AL
GAUGES AcG PVDF BARE ALUM.
24 GA TA10241 TA102XX - 152 lbs
22 GA TA20241 TA202XX
20 GA TA30241 TA302XX
.032 AL
.040 AL
- TA101XXA TA10101A 86 lbs
- TA201XXA TA20101A 105 lbs
23/8" or 3"
w/ CAp
23/8" RIB HEIGHt
- TA102XXA TA10201A 75 lbs
- TA202XXA TA20102A 92 lbs
- 218 lbs
- 261 lbs
- 194 lbs
- 232 lbs
WEIGHt
PER SQ.
WEIGHt
PER SQ.
3" RIB HEIGHt
GAUGES AcG PVDF BARE ALUM.
24 GA TA10541 TA105XX - 182 lbs
22 GA TA20541 TA205XX
20 GA TA30541 TA305XX
.032 AL
.040 AL
16" COVERAGE
C
GAUGES AcG PVDF BARE ALUM.
24 GA TA10641 TA106XX - 160 lbs
22 GA TA20641 TA206XX
20 GA TA30641 TA306XX
.032 AL
.040 AL
18" COVERAGE
- TA105XXA TA10501A 90 lbs
- TA205XXA TA20501A 111 lbs
3" RIB HEIGHt
- TA106XXA TA10601A 79 lbs
- TA206XXA TA20601A 97 lbs
WEIGHt
PER SQ.
- 231 lbs
- 276 lbs
WEIGHt
PER SQ.
- 203 lbs
- 243 lbs
23/8" or 3"
w/ CAp
23/8" RIB HEIGHt
GAUGES AcG PVDF BARE ALUM.
24 GA TA10341 TA103XX - 146 lbs
22 GA TA20341 TA203XX
20 GA TA30341 TA303XX
.032 AL
.040 AL
23/8" or 3"
w/ CAp
GAUGES AcG PVDF BARE ALUM.
24 GA TA10441 TA104XX - 133 lbs
22 GA TA20441 TA204XX
20 GA TA30441 TA304XX
.032 AL
.040 AL
- TA103XXA TA10301A 72 lbs
- TA203XXA TA20301A 88 lbs
23/8" RIB HEIGHt
- TA104XXA TA10401A 65 lbs
- TA204XXA TA20401A 80 lbs
- 186 lbs
- 222 lbs
- 170 lbs
- 203 lbs
WEIGHt
PER SQ.
C
WEIGHt
PER SQ.
C
3" RIB HEIGHt
GAUGES AcG PVDF BARE ALUM.
24 GA TA10741 TA107XX - 152 lbs
22 GA TA20741 TA207XX
20 GA TA30741 TA307XX
.032 AL
.040 AL
24" COVERAGE
GAUGES AcG PVDF BARE ALUM.
24 GA TA10841 TA108XX - 138 lbs
22 GA TA20841 TA208XX
20 GA TA30841 TA308XX
.032 AL
.040 AL
- TA107XXA TA10701A 75 lbs
- TA207XXA TA20701A 92 lbs
3" RIB HEIGHt
- TA108XXA TA10801A 67 lbs
- TA208XXA TA20801A 83 lbs
WEIGHt
PER SQ.
- 194 lbs
- 232 lbs
WEIGHt
PER SQ.
- 176 lbs
- 211 lbs
*panel weight includes the panel cap and panel clips at a 48" spacing
3" rib height and 24" wide panels currently not available
© Metal Sales Manufacturing Corporation / Subject to change without notice 09/14
7
PEncIL RIB PAnEL PRoFILE
12" COVERAGE
23/8" or 3"
w/ CAp
23/8" RIB HEIGHt
GAUGES AcG PVDF BARE ALUM.
24 GA TA11141 TA111XX - 172 lbs
22 GA TA21141 TA211XX
20 GA TA31141 TA311XX
.032 AL
.040 AL
GAUGES AcG PVDF BARE ALUM.
24 GA TA11241 TA112XX - 152 lbs
22 GA TA21241 TA212XX
20 GA TA31241 TA312XX
.032 AL
.040 AL
- TA111XXA TA11101A 86 lbs
- TA211XXA TA21101A 105 lbs
23/8" or 3"
w/ CAp
23/8" RIB HEIGHt
- TA112XXA TA11201A 75 lbs
- TA212XXA TA11202A 92 lbs
- 218 lbs
- 261 lbs
- 194 lbs
- 232 lbs
WEIGHt
PER SQ.
WEIGHt
PER SQ.
4"
C
3" RIB HEIGHt
GAUGES AcG PVDF BARE ALUM.
24 GA TA11541 TA115XX - 182 lbs
22 GA TA21541 TA215XX
20 GA TA31541 TA315XX
.032 AL
.040 AL
16" COVERAGE
4"
C
GAUGES AcG PVDF BARE ALUM.
24 GA TA11641 TA116XX - 160 lbs
22 GA TA21641 TA216XX
20 GA TA31641 TA316XX
.032 AL
.040 AL
- TA115XXA TA11501A 90 lbs
- TA215XXA TA21501A 111 lbs
3" RIB HEIGHt
- TA116XXA TA11601A 79 lbs
- TA216XXA TA21601A 97 lbs
WEIGHt
PER SQ.
- 231 lbs
- 276 lbs
WEIGHt
PER SQ.
- 203 lbs
- 243 lbs
23/8" or 3"
w/ CAp
23/8" RIB HEIGHt
GAUGES AcG PVDF BARE ALUM.
24 GA TA11341 TA113XX - 146 lbs
22 GA TA21341 TA213XX
20 GA TA31341 TA313XX
.032 AL
.040 AL
23/8" or 3"
w/ CAp
GAUGES AcG PVDF BARE ALUM.
24 GA TA11441 TA114XX - 133 lbs
22 GA TA21441 TA214XX
20 GA TA31441 TA314XX
.032 AL
.040 AL
8
- TA113XXA TA11301A 72 lbs
- TA213XXA TA21301A 88 lbs
23/8" RIB HEIGHt
- TA114XXA TA11401A 65 lbs
- TA214XXA TA21401A 80 lbs
*panel weight includes the panel cap and panel clips at a 48" spacing
3" rib height and 24" wide panels currently not available
© Metal Sales Manufacturing Corporation / Subject to change without notice 09/14
- 186 lbs
- 222 lbs
C
- 170 lbs
- 203 lbs
WEIGHt
PER SQ.
WEIGHt
PER SQ.
18" COVERAGE
4"
C
3" RIB HEIGHt
GAUGES AcG PVDF BARE ALUM.
24 GA TA11741 TA117XX - 152 lbs
22 GA TA21741 TA217XX
20 GA TA31741 TA317XX
.032 AL
.040 AL
24" COVERAGE
8"
GAUGES AcG PVDF BARE ALUM.
24 GA TA11841 TA118XX - 138 lbs
22 GA TA21841 TA218XX
20 GA TA31841 TA318XX
.032 AL
.040 AL
- TA117XXA TA11701A 75 lbs
- TA217XXA TA21701A 92 lbs
3" RIB HEIGHt
- TA118XXA TA11801A 67 lbs
- TA218XXA TA21801A 83 lbs
WEIGHt
PER SQ.
- 194 lbs
- 232 lbs
WEIGHt
PER SQ.
- 176 lbs
- 211 lbs
T-ARMOR
MInoR RIB PAnEL PRoFILE
12" COVERAGE
23/8" or 3"
w/ CAp
23/8" RIB HEIGHt
GAUGES AcG PVDF BARE ALUM.
24 GA TA12141 TA121XX - 172 lbs
22 GA TA22141 TA221XX
20 GA TA32141 TA321XX
.032 AL
.040 AL
GAUGES AcG PVDF BARE ALUM.
24 GA TA12241 TA122XX - 152 lbs
22 GA TA22241 TA222XX
20 GA TA32241 TA322XX
.032 AL
.040 AL
- TA121XXA TA12101A 86 lbs
- TA221XXA TA22101A 105 lbs
23/8" or 3"
w/ CAp
23/8" RIB HEIGHt
- TA122XXA TA12201A 75 lbs
- TA222XXA TA22201A 92 lbs
- 218 lbs
- 261 lbs
- 194 lbs
- 232 lbs
7
/8"
WEIGHt
PER SQ.
WEIGHt
PER SQ.
7
/8"
C
3" RIB HEIGHt
GAUGES AcG PVDF BARE ALUM.
24 GA TA12541 TA125XX - 182 lbs
22 GA TA22541 TA225XX
20 GA TA32541 TA325XX
.032 AL
.040 AL
16" COVERAGE
C
GAUGES AcG PVDF BARE ALUM.
24 GA TA12641 TA126XX - 160 lbs
22 GA TA22641 TA226XX
20 GA TA32641 TA326XX
.032 AL
.040 AL
- TA125XXA TA12501A 90 lbs
- TA225XXA TA22501A 111 lbs
41/2"
3" RIB HEIGHt
- TA126XXA TA12601A 79 lbs
- TA226XXA TA22601A 97 lbs
WEIGHt
PER SQ.
- 231 lbs
- 276 lbs
WEIGHt
PER SQ.
- 203 lbs
- 243 lbs
18" COVERAGE
23/8" or 3"
w/ CAp
23/8" RIB HEIGHt
GAUGES AcG PVDF BARE ALUM.
24 GA TA12341 TA123XX - 146 lbs
22 GA TA22341 TA223XX
20 GA TA32341 TA323XX
.032 AL
.040 AL
23/8" or 3"
w/ CAp
GAUGES AcG PVDF BARE ALUM.
24 GA TA12441 TA124XX - 133 lbs
22 GA TA22441 TA224XX
20 GA TA32441 TA324XX
.032 AL
.040 AL
*panel weight includes the panel cap and panel clips at a 48" spacing
3" rib height and 24" wide panels currently not available
- TA123XXA TA12301A 72 lbs
- TA223XXA TA22301A 88 lbs
C
23/8" RIB HEIGHt
- TA124XXA TA12401A 65 lbs
- TA224XXA TA22401A 80 lbs
© Metal Sales Manufacturing Corporation / Subject to change without notice 09/14
7
/8"
C
WEIGHt
PER SQ.
- 186 lbs
- 222 lbs
7
/8"
WEIGHt
PER SQ.
- 170 lbs
- 203 lbs
24" COVERAGE
41/2"
3" RIB HEIGHt
GAUGES AcG PVDF BARE ALUM.
24 GA TA12741 TA127XX - 152 lbs
22 GA TA22741 TA227XX
20 GA TA32741 TA327XX
.032 AL
.040 AL
GAUGES AcG PVDF BARE ALUM.
24 GA TA12841 TA128XX - 138 lbs
22 GA TA22841 TA228XX
20 GA TA32841 TA328XX
.032 AL
.040 AL
- TA127XXA TA12701A 75 lbs
- TA227XXA TA22701A 92 lbs
41/2"
3" RIB HEIGHt
- TA128XXA TA12801A 67 lbs
- TA228XXA TA22801A 83 lbs
- 194 lbs
- 232 lbs
- 176 lbs
- 211 lbs
WEIGHt
PER SQ.
WEIGHt
PER SQ.
9
StRIAtED PAnEL PRoFILE
12" COVERAGE
23/8" or 3"
w/ CAp
C
23/8" RIB HEIGHt
GAUGES AcG PVDF BARE ALUM.
24 GA TA13141 TA131XX - 172 lbs
22 GA TA23141 TA231XX
20 GA TA33141 TA331XX
.032 AL
.040 AL
GAUGES AcG PVDF BARE ALUM.
24 GA TA13241 TA132XX - 152 lbs
22 GA TA23241 TA232XX
20 GA TA33241 TA332XX
.032 AL
.040 AL
- TA131XXA TA13101A 86 lbs
- TA231XXA TA23101A 105 lbs
23/8" or 3"
w/ CAp
23/8" RIB HEIGHt
- TA132XXA TA13201A 75 lbs
- TA232XXA TA23202A 92 lbs
- 218 lbs
- 261 lbs
- 194 lbs
- 232 lbs
WEIGHt
PER SQ.
WEIGHt
PER SQ.
3" RIB HEIGHt
GAUGES AcG PVDF BARE ALUM.
24 GA TA13541 TA135XX - 182 lbs
22 GA TA23541 TA235XX
20 GA TA33541 TA335XX
.032 AL
.040 AL
16" COVERAGE
C
GAUGES AcG PVDF BARE ALUM.
24 GA TA13641 TA136XX - 160 lbs
22 GA TA23641 TA236XX
20 GA TA33641 TA336XX
.032 AL
.040 AL
18" COVERAGE
- TA135XXA TA13501A 90 lbs
- TA235XXA TA23501A 111 lbs
3" RIB HEIGHt
- TA136XXA TA13601A 79 lbs
- TA236XXA TA23601A 97 lbs
WEIGHt
PER SQ.
- 231 lbs
- 276 lbs
WEIGHt
PER SQ.
- 203 lbs
- 243 lbs
23/8" or 3"
w/ CAp
23/8" RIB HEIGHt
GAUGES AcG PVDF BARE ALUM.
24 GA TA13341 TA133XX - 146 lbs
22 GA TA23341 TA233XX
20 GA TA33341 TA333XX
.032 AL
.040 AL
23/8" or 3"
w/ CAp
GAUGES AcG PVDF BARE ALUM.
24 GA TA13441 TA134XX - 133 lbs
22 GA TA23441 TA234XX
20 GA TA33441 TA334XX
.032 AL
.040 AL
- TA133XXA TA13301A 72 lbs
- TA233XXA TA23301A 88 lbs
23/8" RIB HEIGHt
- TA134XXA TA13401A 65 lbs
- TA234XXA TA23401A 80 lbs
- 186 lbs
- 222 lbs
- 170 lbs
- 203 lbs
WEIGHt
PER SQ.
C
WEIGHt
PER SQ.
C
GAUGES AcG PVDF BARE ALUM.
24 GA TA13741 TA137XX - 152 lbs
22 GA TA23741 TA237XX
20 GA TA33741 TA337XX
.032 AL
.040 AL
24" COVERAGE
GAUGES AcG PVDF BARE ALUM.
24 GA TA13841 TA138XX - 138 lbs
22 GA TA23841 TA238XX
20 GA TA33841 TA338XX
.032 AL
.040 AL
3" RIB HEIGHt
WEIGHt
PER SQ.
- 194 lbs
- 232 lbs
- TA137XXA TA13701A 75 lbs
- TA237XXA TA23701A 92 lbs
3" RIB HEIGHt
WEIGHt
PER SQ.
- 176 lbs
- 211 lbs
- TA138XXA TA13801A 67 lbs
- TA238XXA TA23801A 83 lbs
10
*panel weight includes the panel cap and panel clips at a 48" spacing
3" rib height and 24" wide panels currently not available
© Metal Sales Manufacturing Corporation / Subject to change without notice 09/14
T-ARMOR
MESA PAnEL PRoFILE
12" COVERAGE
23/8" or 3"
w/ CAp
23/8" RIB HEIGHt
GAUGES AcG PVDF BARE ALUM.
24 GA TA14141 TA141XX - 172 lbs
22 GA TA24141 TA241XX
20 GA TA34141 TA341XX
.032 AL
.040 AL
GAUGES AcG PVDF BARE ALUM.
24 GA TA14241 TA142XX - 152 lbs
22 GA TA24241 TA242XX
20 GA TA34241 TA342XX
.032 AL
.040 AL
- TA141XXA TA14101A 86 lbs
- TA241XXA TA24101A 105 lbs
23/8" or 3"
w/ CAp
23/8" RIB HEIGHt
C
- TA142XXA TA14201A 75 lbs
- TA242XXA TA24201A 92 lbs
C
1
/8"
WEIGHt
PER SQ.
- 218 lbs
- 261 lbs
1
/8"
1
/8"
WEIGHt
PER SQ.
- 194 lbs
- 232 lbs
4" 1"
1
/8"
3" RIB HEIGHt
GAUGES AcG PVDF BARE ALUM.
24 GA TA14541 TA145XX - 182 lbs
22 GA TA24541 TA245XX
20 GA TA34541 TA345XX
.032 AL
.040 AL
16" COVERAGE
4" 2"
GAUGES AcG PVDF BARE ALUM.
24 GA TA14641 TA146XX - 160 lbs
22 GA TA24641 TA246XX
20 GA TA34641 TA346XX
.032 AL
.040 AL
- TA145XXA TA14501A 90 lbs
- TA245XXA TA24501A 111 lbs
3" RIB HEIGHt
- TA146XXA TA14601A 79 lbs
- TA246XXA TA24601A 97 lbs
WEIGHt
PER SQ.
- 231 lbs
- 276 lbs
WEIGHt
PER SQ.
- 203 lbs
- 243 lbs
23/8" or 3"
w/ CAp
23/8" RIB HEIGHt
GAUGES AcG PVDF BARE ALUM.
24 GA TA14341 TA143XX - 146 lbs
22 GA TA24341 TA243XX
20 GA TA34341 TA343XX
.032 AL
.040 AL
23/8" or 3"
w/ CAp
GAUGES AcG PVDF BARE ALUM.
24 GA TA14441 TA144XX - 133 lbs
22 GA TA24441 TA244XX
20 GA TA34441 TA344XX
.032 AL
.040 AL
- TA143XXA TA14301A 72 lbs
- TA243XXA TA24301A 88 lbs
C
23/8" RIB HEIGHt
- TA144XXA TA14401A 65 lbs
- TA244XXA TA24401A 80 lbs
C
1
/8"
1
/8"
WEIGHt
PER SQ.
- 186 lbs
- 222 lbs
1
/8"
1
/8"
WEIGHt
PER SQ.
- 170 lbs
- 203 lbs
18" COVERAGE
4" 3"
3" RIB HEIGHt
GAUGES AcG PVDF BARE ALUM.
24 GA TA14741 TA147XX - 152 lbs
22 GA TA24741 TA247XX
20 GA TA34741 TA347XX
.032 AL
.040 AL
24" COVERAGE
4" 3"
GAUGES AcG PVDF BARE ALUM.
24 GA TA14841 TA148XX - 138 lbs
22 GA TA24841 TA248XX
20 GA TA34841 TA348XX
.032 AL
.040 AL
- TA147XXA TA14701A 75 lbs
- TA247XXA TA24701A 92 lbs
3" RIB HEIGHt
- TA148XXA TA14801A 67 lbs
- TA248XXA TA24801A 83 lbs
- 194 lbs
- 232 lbs
- 176 lbs
- 211 lbs
WEIGHt
PER SQ.
WEIGHt
PER SQ.
*panel weight includes the panel cap and panel clips at a 48" spacing
3" rib height and 24" wide panels currently not available
© Metal Sales Manufacturing Corporation / Subject to change without notice 09/14
11
PLAnK PAnEL PRoFILE
12" COVERAGE
23/8" or 3"
w/ CAp
23/8" RIB HEIGHt
GAUGES AcG PVDF BARE ALUM.
24 GA TA15141 TA151XX - 172 lbs
22 GA TA25141 TA251XX
20 GA TA35141 TA351XX
.032 AL
.040 AL
GAUGES AcG PVDF BARE ALUM.
24 GA TA15241 TA152XX - 152 lbs
22 GA TA25241 TA252XX
20 GA TA35241 TA352XX
.032 AL
.040 AL
- TA151XXA TA15101A 86 lbs
- TA251XXA TA25101A 105 lbs
23/8" or 3"
w/ CAp
23/8" RIB HEIGHt
C
- TA152XXA TA15201A 75 lbs
- TA252XXA TA25202A 92 lbs
C
1
/8"
WEIGHt
PER SQ.
- 218 lbs
- 261 lbs
1
/8"
WEIGHt
PER SQ.
- 194 lbs
- 232 lbs
6"
3" RIB HEIGHt
GAUGES AcG PVDF BARE ALUM.
24 GA TA15541 TA155XX - 182 lbs
22 GA TA25541 TA255XX
20 GA TA35541 TA355XX
.032 AL
.040 AL
16" COVERAGE
6"
GAUGES AcG PVDF BARE ALUM.
24 GA TA15641 TA156XX - 160 lbs
22 GA TA25641 TA256XX
20 GA TA35641 TA356XX
.032 AL
.040 AL
- TA155XXA TA15501A 90 lbs
- TA255XXA TA25501A 111 lbs
3" RIB HEIGHt
- TA156XXA TA15601A 79 lbs
- TA256XXA TA25601A 97 lbs
WEIGHt
PER SQ.
- 231 lbs
- 276 lbs
WEIGHt
PER SQ.
- 203 lbs
- 243 lbs
23/8" or 3"
w/ CAp
23/8" RIB HEIGHt
GAUGES AcG PVDF BARE ALUM.
24 GA TA13341 TA133XX - 146 lbs
22 GA TA23341 TA233XX
20 GA TA33341 TA333XX
.032 AL
.040 AL
23/8" or 3"
w/ CAp
GAUGES AcG PVDF BARE ALUM.
24 GA TA15441 TA154XX - 133 lbs
22 GA TA25441 TA254XX
20 GA TA35441 TA354XX
.032 AL
.040 AL
12
- TA133XXA TA13301A 72 lbs
- TA233XXA TA23301A 88 lbs
C
23/8" RIB HEIGHt
- TA154XXA TA15401A 65 lbs
- TA254XXA TA25401A 80 lbs
*panel weight includes the panel cap and panel clips at a 48" spacing
3" rib height and 24" wide panels currently not available
C
1
/8"
WEIGHt
PER SQ.
- 186 lbs
- 222 lbs
1
/8"
WEIGHt
PER SQ.
- 170 lbs
- 203 lbs
© Metal Sales Manufacturing Corporation / Subject to change without notice 09/14
18" COVERAGE
6"
3" RIB HEIGHt
GAUGES AcG PVDF BARE ALUM.
24 GA TA13741 TA137XX - 152 lbs
22 GA TA23741 TA237XX
20 GA TA33741 TA337XX
.032 AL
.040 AL
24" COVERAGE
6"
GAUGES AcG PVDF BARE ALUM.
24 GA TA15841 TA158XX - 138 lbs
22 GA TA25841 TA258XX
20 GA TA35841 TA358XX
.032 AL
.040 AL
- TA137XXA TA13701A 75 lbs
- TA237XXA TA23701A 92 lbs
3" RIB HEIGHt
- TA158XXA TA15801A 67 lbs
- TA258XXA TA25801A 83 lbs
WEIGHt
PER SQ.
- 194 lbs
- 232 lbs
WEIGHt
PER SQ.
- 176 lbs
- 211 lbs
T-ARMOR
ACCESSORY PROFILES
t-ARMoR cAP DEScRIPtIon GAUGE PRoDUct no. FInISH Wt/Ft
24 TAC01XX pVDF/ACG 0.21 lbs
Mechanically
Seamed
2"
22 TAC02XX pVDF/ACG 0.27 lbs
20 TAC03XX pVDF/ACG 0.33 lbs
.032 TAC01XXA pVDF 0.10 lbs
Mechanically
Seamed
.040 TAC02XXA pVDF 0.12 lbs
.032 TAC0101A Bare Alum. 0.10 lbs
.040 TAC0201A Bare Alum. 0.12 lbs
Caps come in the same length as
panels unless otherwise specied
t-ARMoR cLIP SIZE tYPE PRoDUct no.
3
/8" 23/8" Utility 3640900 100 pieces 35 lbs
2
3
/4" 23/8" Low 3641000 100 pieces 40lbs
2
3
/4" 23/8" High 3641200 100 pieces 45 lbs
3
CARTON
QUANTITY
3" 3" Utility 3641100 100 pieces 45 lbs
3
/8" 3" Low 3641300 100 pieces 50 lbs
3
3
/4"
3
/4"
3
/4"
3
/8" 3" High 3641400 100 pieces 55 lbs
4
t-ARMoR contInUoUS GAUGE FInISH PRoDUct no. Wt/Ft HEIGHt
cLIP 24 Varies 5855199 .48 lbs 2
24 Varies 5855299 .51 lbs 2
24 Varies 5855399 .59 lbs 3
24 Varies 5855499 .53 lbs 3"
24 Varies 5855599 .56 lbs 3
24 Varies 5855699 .64 lbs 4
22 Varies 6055199 .63 lbs 2
22 Varies 6055299 .66 lbs 2
22 Varies 6055399 .77 lbs 3
22 Varies 6055499 .69 lbs 3"
22 Varies 6055599 .73 lbs 3
22 Varies 6055699 .83 lbs 4
WT/ CARTON
3
/8"
3
/4"
3
/4"
3
/8"
3
/8"
3
/8"
3
/4"
3
/4"
3
/8"
3
/8"
tHERMAL BLocKS SIZE tYPE PRoDUct no. WT/100
3
/8" x 3" x 12"
3
/8" x 3" x 16"
3
/8" x 3" x 18"
3
/8" x 3" x 24"
1" x 3" x 12"
1" x 3" x 16"
1" x 3" x 18"
1" x 3" x 24"
© Metal Sales Manufacturing Corporation / Subject to change without notice 09/14
Polystyrene
Foam
Polystyrene
Foam
Polystyrene
Foam
Polystyrene
Foam
Polystyrene
Foam
Polystyrene
Foam
Polystyrene
Foam
Polystyrene
Foam
4923777 1.25 lbs
4923787 1.50 lbs
4923775 1.75 lbs
4923776 2.00 lbs
4923778 2.75 lbs
4923760 3.00 lbs
4923770 3.50 lbs
4923779 3.75 lbs
13
ACCESSORY PROFILES (CONT.)
FLoAtInG RAKE AnGLE SIZE FInISH LEnGtH
5
/8" x 16 Ga Galvanized 10'-0" 4923810 10.7 lbs
2
1
/8" x 16 Ga Galvanized 10'-0" 4923815 10.9 lbs
3
3
/4" x 16 Ga Galvanized 10'-0" 4923821 11.9 lbs
3
1
/8" x 16 Ga Galvanized 10'-0" 4923825 13.0 lbs
4
PRoDUct no.
Wt
FLoAtInG RAKE AnGLE SIZE FInISH LEnGtH
(CURVED APPLICATION)
25/8" x 16 Ga Galvanized 10'-0" 4923810C 10.7 lbs
1
/8" x 16 Ga Galvanized 10'-0" 4923815C 10.9 lbs
3
3
/4" x 16 Ga Galvanized 10'-0" 4923821C 11.9 lbs
3
1
/8" x 16 Ga Galvanized 10'-0" 4923825C 13.0 lbs
4
EAVE PLAtE SIZE FInISH tYPE
1
/4" x 16 Ga. Galvanized Utility 10'-0" 4923835 6.90 lbs
3
/8" x 16 Ga. Galvanized Low 10'-0" 4923835 7.80 lbs
3
/8" x 16 Ga. Galvanized High 10'-0" 4923845 10.30 lbs
1
EAVE PLATE
(CURVED APPLICATION)
SIZE FINISH TYPE PRODUCT NO. WT
3/8" x 16 Ga. Galvanized Low 10'-0" 4933800 7.80 lbs
13/8" x 16 Ga. Galvanized High 10'-0" 4934800 10.30 lbs
BACK-UP CHANNEL
BEARING PLATE
SIZE FINISH LENGTH PRODUCT NO. WT
3
3" x
3" x
/8" Galvanized 48" 4923640 2.00 lbs
3
/8" Galvanized 72" 4923645 4.00 lbs
SIZE FINISH PRODUCT NO. WT/100
4" x 5" x 20 Ga. Galvanized 4923886 30 lbs
PRoDUct no.
PRoDUct no.
Wt
Wt
14
ENDLAP PAD
TUBE SEALANT
SIZE TYPE PRODUCT NO. WT/CARTON
11/2" x 3/32" x 30'
Butyl 6411999 27 lbs
SIZE COLOR PRODUCT NO.
10.3 oz
10.3 oz
10.3 oz
10.3 oz
Urethane White
Urethane Bronze
Urethane Gray
Acrylic Clear
6402829 30 cartridges 19.31 lbs
6402800 30 cartidges 19.31 lbs
6402830 30 cartridges 19.31 lbs
6402999 30 cartridges 19.31 lbs
StIFFEnER PLAtE SIZE FInISH GAUGE
3
/4"x4" Galvanized 16 3633900 0.55 lbs
4"
3
"
4
/
© Metal Sales Manufacturing Corporation / Subject to change without notice 09/14
CARTON
QUANTITY
PRoDUct no.
WT/ CARTON
Wt/10
T-ARMOR
DOUBLE BEAD TAPE SEALANT
ACCESSORY PROFILES (CONT.)
SIZE TYPE PRODUCT NO.
7/8" x 3/16" x 25' Butyl 6403899 20 rolls 40.00 lbs
CARTON
QUANTITY
WT/ CARTON
VENT MATERIAL
33/8"
7
/8"
4'
TOUCH-UP PAINT
ms-HT UNDERLAYMENT
UNDERLAYMENT
PRIMER
SIZE TYPE PRODUCT NO.
CARTON
QUANTITY
WT/ CARTON
35/16" x 7/8" x 4' Black 6852406 24 pieces 30.00 lbs
For use on roof with a 3:12 or greater slope
TYPE SIZE PRODUCT NO. WT
For PVDF nish 2 oz. Bottle 66005_ _ .15 lbs
For PVDF nish Pint 66010_ _ 1.60 lbs
_ _ Represents color code designation
TYPE SIZE PRODUCT NO. WT/ ROLL
Peel-and-Stick 36" x 66.67’ 4121200 44.00 lbs
(2 Sq Roll)
SIZE PRODUCT NO. WT/ ROLL
5 Gallon* 6600000 42.00 lbs
ALSAN
POLY FLEECE ROLL
HEMMING/TURN-UP TOOL
Varies
© Metal Sales Manufacturing Corporation / Subject to change without notice 09/14
*100-125 ft2 per gallon depending on substrate.
TYPE SIZE PRODUCT NO. WT
5 Gallon* 4130200 47.00 lbs
1 Gallon* 4130300 10.00 lbs
Kit** 5 Gallon 4130100 9.20 lbs
*50 lf per gallon depending on weather tempature
**Kit includes 1 gallon Alsan, tools, instuctional video, and roll of Poly Fleece
SIZE TYPE PRODUCT NO. QUANTITY WT
4" x 50' Poly 4130500 1 rolls .30 lbs
Fleece
6" x 50' Poly 4130400 1 rolls .50 lbs
Fleece
TYPE SIZE PRODUCT NO. WT/100
24" Panel 20" 6560102 3.30 lbs
18" Panel 17" 6560122 2.90 lbs
16" Panel 15" 6560132 2.60 lbs
12" Planel 11" 6560142 2.10 lbs
Used for bending lower end of the metal panel to accept Offset Cleat flashing for
concealed fastener application or for turning up the end of the panel at the high side
15
ACCESSORY PROFILES (CONT.)
PoSt HUnG GUTTER HANGER SIZE FInISH tYPE
6" x 16 Ga. Galvanized Galv 3633800 0.20 lbs
PRoDUct no.
Wt
RIVEt PULLER MoDEL tYPE
Lever Hand Tool
Pulling Head
RUBBER ROOF DECK
FLASHINGS
ROUND
Rubber Roof Jack
Round Base
PRoDUct no.
#RV-200 Lever Hand Tool 3.95 lbs
#RV74G Powered Tool
#RV8840-9 Pulling Head
*Note:
Pulling Head is required with both
the Lever hand and Power tools
COnTACT LOCAL
sALEs BRAnCH
TYPE SIZE BASE DIAM. PRODUCT NO. WT
Rubber #1 Flasher
Rubber #2 Flasher 13/4" - 31/4" 68502_ _* 3.00 lbs
Rubber #3 Flasher
Rubber #4 Flasher 3" - 6
1
/4" - 2" 68501_ _* 3.00 lbs
1
/4" - 5" 68503_ _* 3.00 lbs
1
/4" 68504_ _* 3.00 lbs
Rubber #5 Flasher 41/4" - 71/2" 68505_ _* 5.00 lbs
Rubber #6 Flasher 5" - 9" 68506_ _* 9.00 lbs
Rubber #7 Flasher 6" - 11" 68507_ _* 11.00 lbs
Rubber #8 Flasher 7" - 13" 68508_ _* 13.00 lbs
Rubber #9 Flasher 10" - 19" 68509_ _* 13.00 lbs
*Special order colors: 93=Brown; 94=Green; 95=Red; 96=Blue; 97=White; 98=Grey; 99=Black
HT Silicone #1 Flasher
HT Silicone #2 Flasher 1
HT Silicone #3 Flasher
HT Silicone #4 Flasher 3" - 6
1
/4" - 2" 6850011 3.00 lbs
3
/4" - 31/4" 6850012 3.00 lbs
1
/4" - 5" 6850013 3.00 lbs
1
/4" 6850014 3.00 lbs
HT Silicone #5 Flasher 41/4" - 71/2" 6850015 5.00 lbs
HT Silicone #6 Flasher 5" - 9" 6850016 9.00 lbs
HT Silicone #7 Flasher 6" - 11" 6850017 11.00 lbs
HT Silicone #8 Flasher 7" - 13" 6850018 13.00 lbs
HT Silicone #9 Flasher 10" - 19" 6850019 13.00 lbs
Wt
.55 lbs
SQUARE
16
Retro Roof Jack
Square Base
Retrot HT #1 Masterash
Retrot HT #2 Masterash 1
Retrot HT #3 Masterash
1
/4" - 2" 6850060 4.00 lbs
1
/4" - 3" 6850061 4.00 lbs
1
/4" - 4" 6850062 4.00 lbs
GRAY ROUND RETRO ROOF JACK
1
Retrot E.P.D.M. #1 Masterash
Retrot E.P.D.M. #2 Masterash 1
Retrot E.P.D.M. #3 Masterash
/4" - 2" 6850070 4.00 lbs
1
/4" - 3" 6850071 4.00 lbs
1
/4" - 4" 6850072 4.00 lbs
BLACK ROUND RETRO ROOF JACK
Retrot E.P.D.M. #1 Masterash
Retrot E.P.D.M. #2 Masterash 1
Retrot E.P.D.M. #3 Masterash
1
/4" - 2" 6850073 4.00 lbs
1
/4" - 3" 6850074 4.00 lbs
1
/4" - 4" 6850075 4.00 lbs
BLACK SQUARE RETRO ROOF JACK
Retrot E.P.D.M. #1 Masterash
Retrot E.P.D.M. #2 Masterash 11/4" - 3" 6850047 4.00 lbs
Retrot E.P.D.M. #3 Masterash
*Kit includes: membrane fasteners, termination strips, splice material and
sealant. (Deck Flashing temperature range is -65o to +250o: HT Deck Flashing
temperature range is -100o to +450o)
© Metal Sales Manufacturing Corporation / Subject to change without notice 09/14
1
/4" - 2" 6850046 4.00 lbs
1
/4" - 4" 6850048 4.00 lbs
T-ARMOR
VENTED RIDGE COVER
3"
X*
1"
3"
Hem
FLASHING PROFILES
GAUGE FINISH PRODUCT NO. WT LENGTH
C
1
/8"
1
24 ACG 5701341 13.40 lbs 10'-2"
24 ACG 5701541 26.80 lbs 20'-3"
24 PVDF 58013_ _ 13.40 lbs 10'-2"
7
/8"
24 PVDF 58015_ _ 26.80 lbs 20'-3"
* See chart on page 6
VENT DRIP
3
/4"
3
/4"
105°
135°
C
SSR RIDGE
C
135°
Hem
7" RIDGE/HIP COVER
C
Open
Hem
EXPANSION JOINT
41/2"
2"
X*
31/4"
4"
X*
1"
1"
Hem
7"
GAUGE FINISH PRODUCT NO. WT LENGTH
24 ACG 5701741 3.30 lbs 10'-2"
24 PVDF 58017_ _ 3.30 lbs 10'-2"
GAUGE FINISH PRODUCT NO. WT LENGTH
24 ACG 5775141 15.20 lbs 10'-2"
24 ACG 5775341 30.40 lbs 20'-3"
4"
24 PVDF 58751_ _ 15.20 lbs 10'-2"
24 PVDF 58753_ _ 30.40 lbs 20'-3"
* See chart on page 6
GAUGE FINISH PRODUCT NO. WT LENGTH
24 ACG 5854441 12.70 lbs 10'-2"
24 ACG 5855441 25.40 lbs 20'-3"
24 PVDF 58544_ _ 12.70 lbs 10'-2"
1"
24 PVDF 58554_ _ 25.40 lbs 20'-3"
* See chart on page 6
GAUGE FINISH PRODUCT NO. WT LENGTH
24 ACG 6372241 12.50 lbs 10'-2"
C
24 ACG 6372341 25.00 lbs 20'-3"
24 PVDF 64722_ _ 12.50 lbs 10'-2"
24 PVDF 64723_ _ 25.00 lbs 20'-3"
15" VALLEY
Open
Hem
X*
2"
4.5" DROP VALLEY
X*
B
1
/2"
1
41/2"
SYSTEM
LOW
HIGH
A B
3
/8"
3
/8"
1
GAUGE FINISH PRODUCT NO. WT LENGTH
24 ACG 5852841 15.90 lbs 10'-2"
C
7"
24 ACG 5853841 31.70 lbs 20'-3"
1"
24 PVDF 58528_ _ 15.90 lbs 10'-2"
24 PVDF 58538_ _ 31.70 lbs 20'-3"
* See chart on page 6
GAUGE FINISH PRODUCT NO. WT LENGTH
Low 4.5"
Drop Valley
C
A
24 ACG 5781741 18.20 lbs 10'-2"
24 ACG 5781941 36.40 lbs 20'-3"
24 PVDF 58817_ _ 18.20 lbs 10'-2"
24 PVDF 58819_ _ 36.40 lbs 20'-3"
1
/2"
4
1
/2"
3
High 4.5"
Drop Valley
24 ACG 5782341 18.20 lbs 10'-2"
24 ACG 5782541 36.40 lbs 20'-3"
24 PVDF 58823_ _ 18.20 lbs 10'-2"
24 PVDF 58825_ _ 36.40 lbs 20'-3"
* See chart on page 6
© Metal Sales Manufacturing Corporation / Subject to change without notice 09/14
17
9" DROP VALLEY
B C
X*
1
/2"
1
A
9"
SYSTEM
LOW
HIGH
A B
3
/8"
3
/8"
1
10"
9"
FLASHING PROFILES (CONT.)
GAUGE FINISH PRODUCT NO. WT LENGTH
Low 9"
Drop Valley
24 ACG 5786341 35.60 lbs 10'-2"
24 ACG 5786441 70.80 lbs 20'-3"
24 PVDF 58863_ _ 35.60 lbs 10'-2"
24 PVDF 58864_ _ 70.80 lbs 20'-3"
High 9"
Drop Valley
24 ACG 5786741 35.60 lbs 10'-2"
24 ACG 5786841 70.80 lbs 20'-3"
24 PVDF 58867_ _ 35.60 lbs 10'-2"
24 PVDF 58868_ _ 70.80 lbs 20'-3"
* See chart on page 6
PEAK GAUGE FInISH PRODUCT NO.
C
6"
A*
X*
Open
Hem
* "A" dimension will vary per slope
See chart on page 6
SSR SCULPTURED
HIGH SIDE EAVE
C
4"
61/2"
X*
160°
4"
100°
2"
2"
3
/8"
Hem
Open
Hem
DESCRIPTION
24 pVDF 58551_ _ 2
24 ACG 5855141 2
24 pVDF 58522_ _ 2
24 ACG 5852241 2
24 pVDF 58523_ _ 2
24 ACG 5852341 2
3
/8" Utility 10'-2"
3
/8" Utility 10'-2"
3
/8" Low 10'-2"
3
/8" Low 10'-2"
3
/8" High 10'-2"
3
/8" High 10'-2"
LENGTH
24 pVDF 58524_ _ 3" Utility 10'-2"
24 ACG 5852441 3" Utility 10'-2"
24 pVDF 58525_ _ 3" Low 10'-2"
24 ACG 5852541 3" Low 10'-2"
24 pVDF 58526_ _ 3" High 10'-2"
24 ACG 5852641 3" High 10'-2"
GAUGE FINISH PRODUCT NO. WT LENGTH
24 ACG 5776941 16.75 lbs 10'-2"
24 ACG 5777141 33.50 lbs 20'-3"
24 PVDF 58769_ _ 16.75 lbs 10'-2"
24 PVDF 58771_ _ 33.50 lbs 20'-3"
* See chart on page 6
EAVE
37/8"
C
X*
A*
5
/8"
Open
Hem
* "A" dimension will vary per slope
See chart on page 6
18
© Metal Sales Manufacturing Corporation / Subject to change without notice 09/14
GAUGE FINISH PRODUCT NO. WT LENGTH
24 ACG 5706541 6.35 lbs 10'-2"
24 PVDF 58065_ _ 6.35 lbs 10'-2"
* See chart on page 6
T-ARMOR
T-ARMOR
SCULPTURED EAVE
2"
Hem
35/8"
X*
2"
FLASHING PROFILES (CONT.)
GAUGE FINISH PRODUCT NO. WT LENGTH
24 ACG 5783541 11.50 lbs 10'-2"
24 ACG 5783741 23.00 lbs 20'-3"
17/8"
4"
C
5
/8"
24 PVDF 58835_ _ 11.50 lbs 10'-2"
24 PVDF 58837_ _ 23.00 lbs 20'-3"
* See chart on page 6
RAKE GAUGE FInISH PRODUCT NO.
4"
13/4"
Hem
C
A
Open Hem
5
/8"
23/8" panel
system A
Utility 5
Low 5
High 6
1
/2"
7
/8"
7
/8"
3" panel
system A
Utility 6
Low 6
High 7
1
/8"
1
/2"
1
/2"
OFFSET RAKE SLIDE GAUGE
1"
A
1"
B
2"
23/8" panel
system A B
Utility 2
Low 2
High 3
1
/2"1/4"
7
/8"3/8"
7
/8" 13/8"
3" panel
system A B
Utility 3
Low 3
High 4
1
/8"1/4"
1
/2"3/8"
1
/2" 13/8"
DESCRIPTION
3
24 pVDF 58537_ _ 2
24 ACG 5853741 2
24 pVDF 58538_ _ 2
24 ACG 5853841 2
24 pVDF 58539_ _ 2
24 ACG 5853941 2
/8" Utility 10'-2"
3
/8" Utility 10'-2"
3
/8" Low 10'-2"
3
/8" Low 10'-2"
3
/8" High 10'-2"
3
/8" High 10'-2"
24 pVDF 58540_ _ 3" Utility 10'-2"
24 ACG 5854041 3" Utility 10'-2"
24 pVDF 58541_ _ 3" Low 10'-2"
24 ACG 5854141 3" Low 10'-2"
24 pVDF 58542_ _ 3" High 10'-2"
24 ACG 5854241 3" High 10'-2"
PRODUCT
NO.
DESCRIPTION
24 5853199 2
24 5853299 2
24 5853399 2
3
/8" Utility 10'-2" 1.0 lbs
3
/8" Low 10'-2" 1.0 lbs
3
/8" High 10'-2" 1.0 lbs
LENGTH WT
24 5853499 3" Utility 10'-2" 1.0 lbs
24 5853599 3" Low 10'-2" 1.0 lbs
24 5853699 3" High 10'-2" 1.0 lbs
Supplied in various colors
LENGTH
SSR RAKE SLIDE
3
/4"
1
/2"
C
STARTER
1
/2"
21/2"
GAUGE FINISH PRODUCT NO. WT LENGTH
24 ACG 5776541 2.60 lbs 10'-2"
Hem
24 PVDF 58765_ _ 2.60 lbs 10'-2"
1"
GAUGE FINISH PRODUCT NO. WT LENGTH
24 ACG 5706241 2.60 lbs 10'-2"
C
© Metal Sales Manufacturing Corporation / Subject to change without notice 09/14
24 PVDF 58053_ _ 2.60 lbs 10'-2"
19
SSR SCULPTURED RAKE
(OFF MODULE)
C
61/2"
100°
4"
160°
4"
100°
2"
5
2"
/8"
Hem
FLASHING PROFILES (CONT.)
GAUGE FINISH PRODUCT NO. WT LENGTH
24 ACG 5775941 16.75 lbs 10'-2"
24 ACG 5776141 33.50 lbs 20'-3"
24 PVDF 58759_ _ 16.75 lbs 10'-2"
24 PVDF 58761_ _ 33.50 lbs 20'-3"
SSR SCULPTURED
RAKE END
4"
C
160°
4"
2"
RAKEWALL W/ TURNDOWN
1
/2"
C
31/2"
41/2"
13/4"
Closed Hem
PITCH BREAK
C
4"
X*
4"
1"
4"
GAUGE FINISH PRODUCT NO. WT
24 ACG 5776341 .18 lbs
24 PVDF 58763_ _ .18 lbs
GAUGE FINISH PRODUCT NO. WT LENGTH
24 ACG 5855641 8.50 lbs 10'-2"
24 PVDF 58556_ _ 8.50 lbs 10'-2"
GAUGE FINISH PRODUCT NO. WT LENGTH
24 ACG 5777341 10.80 lbs 10'-2"
24 ACG 5777541 21.60 lbs 20'-3"
24 PVDF 58773_ _ 10.80 lbs 10'-2"
24 PVDF 58775_ _ 21.60 lbs 20'-3"
Open
Hem
* See chart on page 6
COUNTER FLASHING
5
/8"
1"
Hem
REGLET FLASHING
C
2"
Hem
20
GAUGE FINISH PRODUCT NO. WT LENGTH
24 ACG 5705241 3.35 lbs 10'-2"
24 PVDF 58052_ _ 3.35 lbs 10'-2"
3
/4"
C
3
/4"
GAUGE FINISH PRODUCT NO. WT LENGTH
1
/2"
1"
5
/8"
© Metal Sales Manufacturing Corporation / Subject to change without notice 09/14
24 ACG 5705441 3.20 lbs 10'-2"
24 PVDF 58054_ _ 3.20 lbs 10'-2"
T-ARMOR
BOX GUTTER
31/2"
X*
5"
POST HUNG GUTTER
Open
Hem
51/2"
Open
Hem
Open
Hem
5"
9
/16"
3"
4"
FLASHING PROFILES (CONT.)
GAUGE FINISH PRODUCT NO. WT LENGTH
24 ACG 5707741 16.95 lbs 10'-2"
24 ACG 5707941 33.90 lbs 20'-3"
1"
24 PVDF 58077_ _ 16.95 lbs 10'-2"
24 PVDF 58079_ _ 33.90 lbs 20'-3"
* See chart on page 6
GAUGE FINISH PRODUCT NO. WT LENGTH
24 ACG 5853041 15.1 lbs 10'-2"
24 ACG 5853141 30.0 lbs 20'-3"
1"
24 PVDF 58530_ _ 15.1 lbs 10'-2"
24 PVDF 58531_ _ 30.0 lbs 20'-3"
1"
1"
1
C
/2"
C
13/8"
5"
BOX GUTTER END
5"
5"
POST HUNG
GUTTER END
51/2"
41/4"
SSR GUTTER DRIP
C
41/2"
X*
3"
4"
11/8"
1"
1"
GAUGE FINISH PRODUCT NO. WT
1"
C
C
24 ACG 5708141(Left) .24 lbs
5708241 (Right)
24 PVDF 58081_ _(Left) .24 lbs
58082_ _(Right)
GAUGE FINISH PRODUCT NO. WT
24 ACG 5848141
5848241 (Right)
24 PVDF 58481_ _ (Left) .24 lbs
58482_ _
GAUGE FINISH PRODUCT NO. WT LENGTH
24 ACG 5778141 8.70 lbs 10'-2"
24 PVDF 58781_ _ 8.70 lbs 10'-2"
* See chart on page 6
(Left) .24 lbs
(Right)
Hem
UNIVERSAL GUTTER/
DOWNSPOUT STRAP
A-A
C
16"
4” x 6” DOWNSPOUT
6"
A
A
11/2"
4"
GAUGE FINISH PRODUCT NO. WT LENGTH
24 ACG 5709241 .36 lbs 1'-4"
24 PVDF 58092_ _ .36 lbs 1'-4"
Hems
GAUGE FINISH PRODUCT NO. WT LENGTH
24 ACG 5709841 16.95 lbs 10'-2"
24 ACG 5710141 33.90 lbs 20'-3"
C
© Metal Sales Manufacturing Corporation / Subject to change without notice 09/14
24 PVDF 58098_ _ 16.95 lbs 10'-2"
24 PVDF 58101_ _ 33.90 lbs 20'-3"
21
3 1/2” x 4” DOWNSPOUT
1
3
/
2
4"
"
C
FLASHING PROFILES (CONT.)
GAUGE FINISH PRODUCT NO. WT LENGTH
24 ACG 5709441 12.90 lbs 10'-2"
24 ACG 5709741 25.80 lbs 20'-3"
24 PVDF 58094_ _ 12.90 lbs 10'-2"
24 PVDF 58097_ _ 25.80 lbs 20'-3"
4” DOWNSPOUT BRACKET
C
6” DOWNSPOUT BRACKET
C
ELBOWS
D
W
W
4"
6"
C
D
GAUGE FINISH PRODUCT NO. WT
24 ACG 5711041 .12 lbs
24 PVDF 58110_ _ .12 lbs
GAUGE FINISH PRODUCT NO. WT
24 ACG 5711241 .15 lbs
24 PVDF 58112_ _ .15 lbs
GAUGE FINISH PRODUCT NO. WT
31/2" x 4" ELBOWS (D x W)
95 DEGREE
24 ACG 5710241 2.30 lbs
24 PVDF 58102_ _ 2.30 lbs
45 DEGREE
24 ACG 5710641 2.30 lbs
24 PVDF 58106_ _ 2.30 lbs
TYPE A ELBOWS
C
22
C
W
D
TYPE B ELBOW
4"x 6" ELBOWS (D x W)
95 DEGREE
24 ACG 5710441 3.00 lbs
24 PVDF 58104_ _ 3.00 lbs
45 DEGREE
24 ACG 5710841 3.00 lbs
24 PVDF 58108_ _ 3.00 lbs
Notes:
1) Type “A” & “B” has seam on heel. Specify otherwise at time of order.
2) Specify left or right at time of order for Type “B” elbows.
© Metal Sales Manufacturing Corporation / Subject to change without notice 09/14
T-ARMOR
OFFSET CLEAT
11/2"
FLASHING PROFILES (CONT.)
GAUGE FINISH PRODUCT NO. WT LENGTH
1"
24 Supplied in 5806499 2.40 lbs 10'-2"
Various Colors
C
1
/2"
CLEAT
135°
21/2"
23/8" T-ARMOR
Z-CLOSURE
23/8"
1"
3" T-ARMOR
Z-CLOSURE
3"
1"
1"
GAUGE FINISH PRODUCT NO. WT LENGTH
24 Supplied in 5806099 2.40 lbs 10'-2"
1
/2"
Various Colors
C
GAUGE FINISH PRODUCT NO. WT LENGTH
24 ACG 5854541 3.50 lbs 10'-2"
24 PVDF 58545_ _ 3.50 lbs 10'-2"
C
GAUGE FINISH PRODUCT NO. WT LENGTH
24 ACG 5854641 4.00 lbs 10'-2"
24 PVDF 58546_ _ 4.00 lbs 10'-2"
C
1"
23/8" T-ARMOR GAUGE FInISH PRODUCT NO.
RIB COVER
24 pVDF 58547_ _ .10 lbs 8"
24 ACG 5854741 .10 lbs 8"
C
Cut Line
1
/2"
17/8"
22 pVDF 60547_ _ .20 lbs 8"
22 ACG 6054741 .20 lbs 8"
For use on panel with a eave to wall transition (knee
cap). Two Rib Covers are required per panel.
3" T-ARMOR GAUGE FInISH PRODUCT NO.
RIB COVER
24 pVDF 58549_ _ .10 lbs 8"
24 ACG 5854941 .10 lbs 8"
22 pVDF 60549_ _ .20 lbs 8"
1
C
Cut Line
ROOF CLEAT
11/2"
X*
/2"
21/2"
22 ACG 6054941 .20 lbs 8"
For use on panel with a eave to wall transition (knee
cap). Two Rib Covers are required per panel.
GAUGE FINISH PRODUCT NO. WT LENGTH
24 Supplied in 5806499 2.40 lbs 10'-2"
Various Colors
A*
WT
WT
LENGTH
LENGTH
* See chart on page 6
C
© Metal Sales Manufacturing Corporation / Subject to change without notice 09/14
23
POP RIVET
PANCAKE HEAD
WOOD SCREW
FASTENER SELECTION GUIDE
SIZE TYPE PRODUCT NO. FINISH APPLICATION
1
/8"x 3/16" A 8240901 Unpainted Flashing to Panel or Flashing
1
/8"x 3/16" A 82409_ _ Painted Flashing to Panel or Flashing
SIZE TYPE PRODUCT NO. FINISH APPLICATION
#10-12x1" A 8243100 Plated Flashing to wood decking
PANCAKE HEAD DRILLER
LOW PROFILE WOOD SCREW
WOOD SCREW XL
SELF DRILLER XL
SELF DRILLER NO WASHER
SHOULDER SELF DRILLER
SIZE TYPE PRODUCT NO. FINISH APPLICATION
#10-16x1" Driller 8242100 Plated
Flashing to metal
substructure
SIZE TYPE PRODUCT NO. FINISH APPLICATION
#12-11x11/2" A 8244100 Plated Clips to wood decking
SIZE TYPE PRODUCT NO. FINISH APPLICATION
#10-14x11/2"
#10-14x1
1
A
8212300 Unpainted
/2" A 82123_ _ Painted
Panel or Flashing to wood
substructure
Panel or Flashing to wood
substructure
SIZE TYPE PRODUCT NO. FINISH APPLICATION
#12-14x11/4" Driller 8235300 Unpainted
#12-14x1
1
/4" Driller 82353_ _ Painted
Panel or Flashing to metal
substructure
Panel or Flashing to metal
substructure
SIZE TYPE PRODUCT NO. FINISH APPLICATION
1
/4"-14x11/2" Driller (#2 point) 8249300 Plated
#12-24x11/4" Driller (#4 point) 8282000 Plated
#12-14x1" Driller 8242000 Plated
Panel clips to metal
substructure
Panel clips to bar joists up to
3
/8" thick
Accessories to metal
substructure and used with
framing on retrofit
SIZE TYPE PRODUCT NO. FINISH APPLICATION
STITCH SCREW XL
DECK SCREW
BULB-TITE RIVET (Aluminum)
24
© Metal Sales Manufacturing Corporation / Subject to change without notice 09/14
1
/4"-14x11/4" Driller 8281300 Plated
For use with Floating Rake
Zee to substructure
SIZE TYPE PRODUCT NO. FINISH APPLICATION
1
/4"-14x7/8" Stitch 8236800 Unpainted Flashing to Panel or Flashing
1
/4"-14x7/8" Stitch 82368_ _ Painted Flashing to Panel or Flashing
SIZE TYPE PRODUCT NO. FINISH APPLICATION
Panel Clip to metal deck
and rigid board insulation
assembly or wood
substructure
#14-13x2"-8" Driller
Contact Sales
Branch
Black
SIZE TYPE PRODUCT NO. FINISH APPLICATION
9
/32"x1-3/8" A 8240400 Unpainted
9
/32"x1-3/8" A 82404_ _ Painted
To fasten panel together at
panel end laps
To fasten panel together at
panel end laps
Loading...