MET MTYH1428 User Manual

Previously Connected Devices
• It is not necessary to perform the Bluetooth Connection every time, just press and hold the power button until the unit powers on.
• The speaker can remember multiple Bluetooth devices and will always try to re-connect to the last device used.
• To re-connect to a dierent device, turn o Bluetooth on unwanted devices, then access the Bluetooth settings menu on the device you wish to use and select ISB19.
• If the speaker should become unpaired or will not connect normally, follow these steps in your device’s Bluetooth Settings Menu.
» Delete the speaker (“Forget This Device”).
» Turn Bluetooth OFF then ON again, and
repeat the Initial Bluetooth Connection.
ISB19-v2128-01-IB.indd 1-5 30/05/2018 9:46:06 AM
FCC WARNINGS
WARNING: Changes or modications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.
ADDITIONAL WARNINGS
• WARNING: To prevent re or shock hazards, do not expose this unit to rain or moisture.
• WARNING : Where the mains plug or appliance coupler is used as the disconnect device, such disconnect device shall remain readily operable.
• Lithium batteries, like all rechargeable batteries, are recyclable and should be recycled or disposed of according to state and local guidelines. They should never be disposed of in normal household waste and they should never be incinerated, as they might explode. Contact your local government for disposal or recycling practices in your area.
WARNING : This product can expose you to chemicals including lead, which is known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.
P65Warnings.ca.gov. This product meets and complies
with all Federal regulations.
Contact Information
Website: www.iLiveElectronics.com
Email Support: prodinfo@dpiinc.com
Email Parts: partsinfo@dpiinc.com
Phone Support: 1-888-999-4215
Warranty
For Warranty Information and the most up-to-date version of this User’s Guide, go to:
www.iLiveElectronics.com.
Made Green
Protect for Today
Sustain for Tomorrow
Specications are subject to change without notice.
Copyright © 2019 Digital Products International (DPI, Inc.)
of their respective owners.
On-the-Go Bluetooth Speaker
User’s Guide for Model ISB19 v2128-01
Features
DC IN
• Bluetooth wireless range: 60 ft.
• Voice prompts announce speaker functions
• Durable rubberized coating
• Built-in rechargeable battery: approx. 2.5 hrs
playtime at 100% volume
Includes
• USB charging cable
• User’s Guide
Overview
DC IN
Status Indicator Light
Micro-USB Charging Port
Power / Pair Bluetooth
Charging the Battery
Initial charge time is approximately 2 hours. For best performance, charge fully before use.
• Use a Micro-USB to USB cable (included), to connect to the charging port on the speaker to the USB port of a powered on computer or USB power adapter (not included).
Initial Bluetooth Connection
1. Power on and begin pairing by holding the Power button for 9 seconds, until a voice announces “Bluetooth is connecting” and the indicator begins quickly ashing blue. When pairing, remain within
3 feet of the unit.
2. Using the controls on your Bluetooth device, select ISB19 in the Bluetooth Settings to pair.
If need be, refer to the user’s manual for your specic device for more information.
3. When successfully paired, a voice will announce “Bluetooth is connected” and the LED indicator will turn solid blue. Audio from the connected Bluetooth device will now play on the speaker.
4. Use the controls on the connected Bluetooth device to select and play audio.
Press and hold for 9 seconds to power ON and pair Bluetooth.
Press and hold to power ON or OFF.
Power Status Indicator Light
Volume
Press to adjust volume.
Low Battery Flashing red light
Charging Solid Red light
Finished Charging Light OFF
ISB19-v2128-01-IB.indd 6-10 30/05/2018 9:46:07 AM