(VI) Telephone function (optional)
When the machine is turned on, the icon will flicker on the panel if there is an
incoming call; meanwhile, the speaker will play the ring tone. Touch the button
on the touch panel to answer the call, and the icon will stop flickering. Touch
the button on the touch panel again to end the call.
(VII) Failure Alarm Code
This machine has autonomous failure detection function. When the failure is
detected, the corresponding failure code will be displayed on the screen as
Failure Cod e
E1
E2
E3
E4
E5
E6
Failure Des cri ption
Communica tio n failure of steame r
cables
Inlet valve f ail ure
Drain valve f ail ure
Failure of wa ter i nlet or drainage of
steamer
Wate r inlet failure of st eam er
Temp era ture probe failur e
Inspect whe the r poor contact of the s tea mer
Cables occu rs
Inspect the i nle t valve and the conne cti ng wires.
Inspect the d rai n valve and the conne cti ng wires.
Insect the dr ivi ng chip of the water in let o r drainage valve.
Inspect whe the r water failure occ urs .
Inspect whe the r the probe wires are d ama ged or
poorlycon tac ted.
Counterme asu re
IV. Technical Parameters
Operation C ond itions and Charac ter istics
Rated volta ge
Rated curre nt
Insulated r esi stor
Wate rproof level
AC 220V
13.8A
>20M
IPX5
Rated frequ enc y
Rated power
Current lea kag e
Current lea kag e protection
50Hz-60Hz
3050W
As per the ente rpr ise
pr od uct in spectio n
standard
(15-30)mA
STEAM BATHROOM
MODEL : WS-803L
Load type
Steam
Ceiling lam p
Backgroun d lam p
Ozone disin fec tion
Fan
Electroma gne tic
Note 1
valve
Speaker
Do not dispos e this product as unsorted munici pal
waste. Coll ection of s uch waste separately for specia l
treatment is necessa ry.
Load Configuration Parameters
Rated load vo lta ge
Ac 220V
Ac 12V
Ac 12V
Ac 12V
Dc 12V
Dc 12V
-----
Rated load fr equ ency
50Hz/60Hz
50Hz/60Hz
50Hz/60Hz
50Hz/60Hz
-----
-----
-----
Rated load po wer
3kW
25W
5W
5W
3W
5W
8/10W
QTY
1
1
1
1
1
2
1
Sanitary Ware Expert,
Your best choice!
TECHNIQUE PARAMETER
Vo ltage
AC220V( 10± %)
Fr equency
50/60HZ
Water Volatge Power of steam generator
0.1~0.2Mpa
3KW
(II) Alarm function
when the machine is turned on , touch the button 3seconds on the panel to turn
on alarm function, the screen showing ,meanwhile ,turn off steam function
and radio function , and turn on fan function and lamp function .The speaker will be
sound the alarm .After touch the button turn off the alarm will relief the alarm.
(II) Lamp functi on
When the machine is turned on, touch the button on the touch panel to turn on/off
the ceiling lamp.
CONSTRUCTION SKETCH
Ha nd ra il
Gl as s do or
(III) Fan functi on
When the machine is turned on, touch the button on the touch panel to turn on/off
the fan. When the fan is turned on, the fan indicate will illuminate simultaneously.
(IV) Radio funct ion
1、 When the machine is turned on, touch the button on the touch panel to turn
on/off the radio function. When the radio function is turned on, the radio frequency
will be displayed on the screen, such as .
2、 Touch the button on the touch panel to go to the frequency tuning mode, and
the icon will flicker on the screen. Press the button or to tune the radio
frequency. Touch and hold the button to store the current frequency, and the
currently stored frequency channel will be displayed on the screen, such as .
3、 When the radio is turned on, touch the button to swap the f requency channels,
and the range of frequency channels is from 1 to 8.
4、Under the radio status, touch the button on the touch panel to go to the volume
adjustment mode, and the range of adjustment is from 1 to 15, and the volume will be
displayed on the screen during adjustment, such as .
(V) Steam functi on
1、 When the machine is turned on, touch the button on the touch panel to turn
on/off the steam function. When the steam function is started, the steam function
indicator will illuminate. After the steam function is enabled, the default set time
for steam is 45 minutes, and the default temperature is 100F.
01
SIZE:1380X880X2150mm
2、When the steam function is started, touch the button on the touch panel to go
to the steam setting mode. If the icon flickers on the screen, such as , it enters
the steam time setting status, and the number displayed is the remaining time for
Mo ve ab le s ho we r
steam operation. Touch the button again t o swap to the steam temperature setting
status, and the icon flickers on the screen, such as , and the number displayed
is the steam temperature setting value.
WS-803L
10
I. Instructions
1. Capacitor touch buttons are adopted in this panel. In selecting the position to
install the panel, we should avoid facing directly the spray and shower nozzle,
otherwise it may lead to mistaken operation of the panel or locking the panel;
2. The location area of each function button on the panel is the optimum touch
range;
3. The panel is optimized with waterproof function. When mistaken operation is
tested (with two or more keys touched simultaneously), there will be no response.
Wait for about 1 second to restore operation.
4. Under the status of panel locking, the system gives no response when touching
the panel, and the icon flickers on the LCD. At this time, touch the key for
two seconds, and the locking will be released. Meanwhile, the icon goes off on
the LCD, and you can operate the keys on the panel.
5. When touching any key on the panel, the operating system will give a “beep”
tone if the system operation is enabled.
II. Introduction to Functions
1.Lamp function; 2.Fan function; 3.Steam function;
4
5
6
15
7
CONSTRU CT ION SKET CH
1
2
3
10
11
12
13
14
16
4.Radio function 5.Telephone function; 6.Failure code indication;
7.Ozone disinfection after turning off; 8.Alarm function
III. Method of Operation
(I) Turn on/off the machine
1. Standby mode
The system is in standby mode after power on, and a red dot will be displayed on the
screen to indicate connected power.
2. Turn on the machine
When the system is in standby mode, touch and hold the button for two seconds to
start the machine and the current temperature will be displayed on the screen, such as
. At the same time, the ceiling lamp will light up. When the machine is
started, it is timed for 60 minutes and the machine will shut off automatically when
the time is due.
3. Turn off the machine
Either the button on the touch panel is touched or the default set time (60 minutes)
is up, the machine will be turned off, and all the activated functions will be
disenabled, and the system will go back to the standby mode. After the system is
turned off for 30 seconds, the automatic water discharge function will be started
automatically.
8
18
9
1、top light
2、speaker
3、top shower
4、room body
5、moveable shower
6、control panel
7、towel shelf
8、seat
9、drainage
10、exhaust fan
11、ozone
12、decorated light
13、mirror
14、shift switch
17
19
15、back light
16、cold/hot water switch
17、nozzle
18、steam out
19、bottom tray
WS-803L
0209
INSTALLATION SKETCH
0
5
1
Cold water pipe
Hot water pipe
The socket
of power and
the socket
of telephone
1800
1250
0
0
6
9
0
Other screws
M4x15 M4x25 ST5x25
Install the screw
M6x25
2
Active chain wheel of glass
SIZE:1380X880X2150mm
ILLUSTRATION OF INSTALLATION
1.The products should be installed by technical guy who are got
the certificate or those technical who are assign by dealers. The
main power switch and electronic leakage device should be
installed.
2.The plug of electronic should be installed above the steam
generator and the length of electronic wire not less then
1800MM from the earth.
3.There are should be with main power switch for hot and cold
water pipe of steam room and the water pipe should be connect
to drainage water pipe.
4.Install the products according to the diagram of installation
When fixed the place for the products.
03
A
1、On/Off function key
2、Fan function k ey
3、Steam adjust ment function key
4、Radio/Telephone receive function key
5、Parameter setting decrease key
A、Fan function indicator
E
S
B
6、Lamp/Alarm function key
7、Steam function key
8、Radio tuning function key
9、Radio memory key
10、Parameter setting increase key
B、Steam function indicator
WS-803L
08
DRAWING OF WATER CONNECTION
As the“ ”from the picture,please make the connection according to the serial number v1,v2,etc.
Top sh ower
Movable
shower head
Movable
Nozzle
Nozzle
shower head
INSTALLATION PROCESS
STEP 1
Hot water connection
(red pipe)
generator
Steam
ELECTRIC CIRCUIT SKETCH
Bac k light
Ant enna
CD
Pc co ntrol
Tel ephon e
Ele ctric b ox
Ste am gene rator
Exh aust fa n
Roo f lamp
Spe aker
Tem perat ure nee dle
Ozo ne
Cold water connection
(blue pipe)
Power
Dar k red
(li ve)
Blu e
(ne utral )
Twi n Line
(gr ound)
St5x25
STEP 2
Chain wheel of glass door
07
Ear th line
Please inst all the earth line safely
by professi onal technician.
STEP 3
WS-803L
04
Plastic pad
STEP 4
STEP 6
M4×15
STEP 7
STEP 5
05 06
WS-803L
Loading...