Mertik Maxitrol and KG B6RHAT, B6RRAP User Manual

INSTALLATION AND OPERATING INSTRUCTIONS DRAFT FOR OEM USE ONLY

10- BUTTON OPER ATION

Countdown Timer

Program Mode

1 2

Figure 22: 10-button Display

SETTING FAHRENHEIT OR CELSIUS

▪ To change between °C and °F, press

AM

PM

ON
OFF

1 2

and buttons simultaneously.

NOTE: Choosing °F results in a 12 hour

clock. Choosing °C results in a
24 hour clock.

ON
OFF

Time

Temperature

Signal Indicator Child Proof

AM
PM

CHILD PROOF

ON
OFF

1 2

Thermostatic Mode

2nd Burner Feature

AM
PM

Battery Status

Fan

Fahrenheit or Celsius

Light

Eco Mode

ON:

▪ To activate press

and buttons

simultaneously.

▪

is displayed and the Symax is

rendered inoperable, except for the
OFF function.

ENGLISH

SETTING THE TIME

1. Press and buttons simultane-

AM
PM

ON
OFF

1 2

ously. Day ashes.

2. Press

or button to select a num­ber to correspond with the day of the
week (e. g.

  = Monday, = Tuesday,

= Wed nesday,   = Thursday, = F ri -

day,

  = Sat urday, = Sunday).

3. Press

and buttons simultane-

ously. Hour ashes.

4. To select hour press

5. Press

and buttons simultane-

ously. Minutes ash.

6. To select minutes press
ton.

7. To conrm press

and buttons

simultaneously or wait.

or button.

or but-

OFF:
▪ To deactivate press

simultaneously.

▪

disappears.

and buttons

© 2019 Mertik Maxitrol GmbH & Co. KG, All Rights Reserved.

17 / 30

INSTALLATION AND OPERATING INSTRUCTIONS DRAFT FOR OEM USE ONLY

NOTICE

MANUAL MODE (HANDSET)

BEFORE OPERATING

1. Make sure MANUAL knob on the GV60 valve is in the ON,

full counterclockwise

position.

2. Place the ON / OFF switch (if equipped) in the I (ON) position.

TO TURN ON FIRE

When pilot ignition is conrmed, motor turns automatically to
maximum ame height.

▪ Press button (One Button Ignition)

or

AM
PM

ON
OFF

1 2

and button simultaneously

(Two Button Ignition) until two short
beeps (CE version) or continuous
beeping (CSA version) and a blinking
series of lines conrms the start se­quence has begun; release button(s).

▪ Main gas ows once pilot ignition is

conrmed.

▪ The Symax automatically goes into

Manual Mode after main burner igni­tion.

DESIGNATED LOW FIRE AND HIGH FIRE

▪ To go to low re, double-click but-

AM

ton.

▪

is displayed.

NOTE: Flame goes to high re rst be-

fore going to low re.

▪ To go to high re, double-click but-

AM

ton.

▪

is displayed.

If the pilot does not stay lit after several tries, turn the main valve
knob to OFF and follow the instructions “TURN OFF GAS TO
APPLIANCE” (see page 10).

STANDBY MODE (PILOT FLAME)

Handset

▪

Press and hold

button

to set appliance to pilot ame.

TO TURN OFF FIRE

Handset

AM
PM

ON
OFF

1 2

▪ Press

NOTE: A new ignition is possible after

button to turn off

.

the OFF icon stops ashing.

If the appliance will not operate, follow the instructions “TURN
OFF GAS TO APPLIANCE”

(see page 10)

.

COUNTDOWN TIMER

ON / SETTING:

AM
PM

ON
OFF

1 2

1. Press and hold button until is dis-

played, and hour ashes.

2. To select hour press or button.

3. To conrm press

button. Minutes

ash.

4. To select minutes press

5. To conrm press

or button.

button or wait.

OFF:
Press

button,

and Countdown Time

disappear.

NOTE: At end of Countdown Time period, the re shuts off. The

Countdown Timer only works in Manual, Thermostatic,
and Eco Modes. Maximum Countdown Time is 9 hours
and 50 minutes.

FLAME HEIGHT ADJUSTMENT

AM
PM

ON
OFF

1 2

18 / 30

Handset

▪ To increase ame height press and

hold

button.

▪ To decrease ame height or to set ap-

pliance to pilot ame, press and hold

button.

© 2019 Mertik Maxitrol GmbH & Co. KG, All Rights Reserved.

INSTALLATION AND OPERATING INSTRUCTIONS DRAFT FOR OEM USE ONLY

MODES OF OPERATION

Thermostatic Mode

AM
PM

ON
OFF

1 2

AM
PM

ON
OFF

1 2

The room temperature is measured and
compared to the set temperature. The
ame height is then automatically ad­justed to achieve the set temperature.

PROGRAM 1 and 2, each can be pro­grammed to go ON and OFF at specic
times at a set temperature.

  Program Mode

PROGRAM MODE

AM
PM

ON
OFF

1 2

AM
PM

ON
OFF

1 2

ON:

▪ Press
▪

button.

, or , or is displayed.

OFF:

1. Press

2. Press

button.
or button to enter Manual

Mode.

3. Press button to enter Thermostatic
Mode.

4. Press button to enter Eco Mode.

ENGLISH

AM

THERMOSTATIC MODE

AM
PM

ON
OFF

1 2

AM
PM

ON
OFF

1 2

Eco Mode

Flame height modulates between high
and low. If the room temperature is low-

er than the set temperature, the ame

height stays on high for a longer period
of time. If the room temperature is high-

er than the set temperature, the ame

height stays on low for a longer period
of time. One cycle lasts approx. 20 min.

ON:

▪ Press
▪

is displayed, preset temperature is

button.

displayed briey, and then room tem­perature is displayed.

OFF:

1. Press

2. Press

button.

or button to enter Manual

Mode.

3. Press button to enter Program Mode.

4. Press button to enter Eco Mode.

SETTING:

1. Press

button and hold until is dis-

played, temperature ashes.

2. To adjust set temperature press

or

button.

3. To conrm press

button or wait.

NOTE: The set temperature for Thermostatic Mode is the tem-

perature for the ON time in Program Mode. Changing
the Thermostatic Mode set temperature also changes
the ON time temperature in Program Mode.

Default settings:
ON TIME (Thermostatic) TEMPERATURE: 70 °F / 21 °C
OFF TIME TEMPERATURE: “

” (pilot ame only)

TEMPERATURE SETTING:

AM
PM

ON

OFF

1 2

1. Press

ashes.
(setting in Thermostatic Mode) is dis-

played.

2. To continue press

button and hold until

and set temperature

button or wait.

 , is displayed, temperature

ashes.

3. Select OFF temperature by pressing
the

or button.

4. To conrm press

button.

NOTE: The ON (Thermostatic) and OFF set temperatures are

the same for each day.

DAY SETTING:

5.

AM
PM

ON
OFF

1 2

ashes. Press or button to

choose between

, ,  , , ,  ,

 ,  , .

6. To conrm press

button.

© 2019 Mertik Maxitrol GmbH & Co. KG, All Rights Reserved.

19 / 30

INSTALLATION AND OPERATING INSTRUCTIONS DRAFT FOR OEM USE ONLY

SELECTED

ON TIME SETTING (PROGRAM 1):

7.

AM
PM

ON

OFF

1 2

, , is displayed, is dis-

played shortly, and hour ashes.

8. To select hour press

9. To conrm press

is displayed,

or button.

button. , ,

displayed shortly,

and minutes ash.

10. To select minutes press

or but-

ton.

11. To conrm press

button.

OFF TIME SETTING (PROGRAM 1):

AM
PM

ON

OFF

1 2

12. , , is displayed, is dis-

played shortly, and hour ashes.

13. To select hour, press

14. To conrm press

or button.

button. , ,

is displayed, is displayed

shortly, and minutes ash.

15. To select minutes press

or but-

ton.

16. To conrm press

button.

2ND BURNER FEATURE

The latching solenoid valve will open automatically after igni­tion or after switching the system OFF, so that the maximum

ow of gas is supplied to both burners assisting with the ignition

process. After pressing the button for the 2nd Bruner the motor
will turn 7 seconds in the ON direction until the max. position is
reached.

ON:
▪

AM
PM

ON
OFF

1 2

To switch a burner ON, press the
button.

▪

displayed.

OFF:
▪ To switch the burner OFF, press the

button.

▪ disappears.

NOTE: The latching solenoid valve cannot operate manually. If

the receiver battery runs down it will remain in the last
operating position.

NOTE: Either continue to PROGRAM 2 and set on and off times

or stop programming at this point, and PROGRAM 2 re­mains deactivated.

NOTE: PROGRAM 1 and 2 use the same on (Thermostatic) and

off temperatures for

, and Daily Timer (  , , ,

 ,  ,  , ). Once a new ON (Thermostatic) and / or OFF

temperature has been set, that temperature becomes the
new default setting.

NOTE: If

, or Daily Timer are programmed for PRO-

GRAM 1 and PROGRAM 2 ON and OFF times, these
become the new default times. The batteries must be re­moved to clear the PROGRAM 1 and PROGRAM 2 ON
and OFF times and temperatures.

or Daily Timer (  , , ,  ,  ,  , ) selected

▪ Set ON time and OFF time using same procedure as “

se-

lected” (above).

▪

:

Set ON time and OFF time for both Saturday and Sunday.

▪ Daily Timer: Unique ON and OFF times may be set for a single

day of the week, for multiple days of the week, or for every day
of the week.

▪ Wait to nish setting.

ECO MODE

ON:

AM

▪ Press
▪

is displayed.

OFF:

1. Press

2. Press
Mode.

3. Press button to enter Thermostatic
Mode.

4. Press button to enter Program
Mode.

CIRCULATING FAN OPERATION

Circulating fan has 4 speed levels from

AM

low (1 bar) to high (4 bars).

ON / SETTING:

1. Press

ashes.

2. Press
and

3. To conrm setting either press
ton or wait (

button to enter Eco Mode.

button.

or button to enter Manual

button and hold until

button to increase fan speed

button to decrease fan speed.

but-

displayed).

20 / 30

OFF:

Press

button until all 4 speed level

bars disappear.

NOTE: SETTING only. If the fan was not switched OFF after

last use, it starts automatically 4 minutes after ignition
at maximum speed and goes to the last set level after
10 seconds. The fan stops 10 minutes after the gas is
OFF or at pilot.

© 2019 Mertik Maxitrol GmbH & Co. KG, All Rights Reserved.

INSTALLATION AND OPERATING INSTRUCTIONS DRAFT FOR OEM USE ONLY

NOTICE

LIGHT / DIMMER OPERATION

ON:

AM

▪ Press
▪ Light is ON at preset level.

button ( is displayed).

OFF:
Press

button ( disappears).

SETTING:

1. Press

button and hold until ash-

es.

2. To adjust light between 20…100 %
press

3. To conrm setting either press
ton or wait (

or button.

but-

is displayed).

NOTE: The Light works independently of the pilot ame. If you

want the light on but no ame, press

button.

MYFIRE APP

Before the App can be used, the myre Wi-Fi Box must be wired
and plugged into mains power according to myre App setup
diagram (see gure 32, page 30), and the App setup must be
completed (see myre App setup, page 25).

If Thermostatic, Program or Eco Mode

AM
PM

ON
OFF

1 2

is activated in the App, the correspond-

ing icon and “

” is displayed on the

handset.

The modes can be operated according
to the descriptions on previous pages.

NOTE: In Manual Mode “

” is NOT

displayed on the handset.

ENGLISH

© 2019 Mertik Maxitrol GmbH & Co. KG, All Rights Reserved.

21 / 30

INSTALLATION AND OPERATING INSTRUCTIONS DRAFT FOR OEM USE ONLY

NOTICE

NOTICE

NOTICE

THE PUCK HANDSET

TECHNICAL DATA

AMBIENT TEMPERATURE RANGE
CSA: The Puck: 32 °F to 131 °F
CE: The Puck: 0 °C to 55 °C

RADIO FREQUENCY
CSA: 918.0 MHz for U.S. (FCC), Canada (ISED), New Zea-

land (RNZ) and Australia (ACMA) (The Puck, receiver)

CE: 868.1 MHz for Europe (The Puck, receiver)
(see radio frequency information on page 4.)

RADIATED POWER OUTPUT
CSA: 84.5 µV/m
CE: -18.5 dBm

POWER SUPPLY
Handset: 2 x 1.5 V “AAA” (quality alkaline recommended)

Wiring of valve and receiver must be completed before starting
ignition. Failure to do so could damage the electronics.

The handsets and receivers are not interchangeable with previ­ous electronics G6R and B6R-R8(9)U(T).

SYNCHRONIZATION RECEIVER / THE PUCK HANDSET

See page 7 for more information about synchronization between
receiver and The Puck.

MODES OF OPERATION

When pilot ignition is conrmed, motor turns automatically to
maximum ame height.

TURN FIRE ON AND OFF
▪ Press and hold the

button until two

short beeps conrms the start se­quence has begun; release button.

▪ Main gas ows once pilot ignition is

conrmed.

▪ Press and hold the

OFF

.

button to turn

If the pilot does not stay lit after several tries, turn the main valve
knob to OFF and follow the instructions “TURN OFF GAS TO
APPLIANCE” (see page 10).

To avoid damaging the electronics, do NOT use metal tools to
remove the batteries from the handset / receiver.

▪ Without using a mains adapter, battery replacement is recom-

mended at the beginning of each heating season.

▪ Old or dead batteries should be removed immediately. If left

in the unit the batteries can overheat, leak, and / or explode.

▪ Do NOT expose batteries (including during storage) to direct

sunlight, excessive heat, re, moisture, or severe impact. Each

of these conditions can cause the batteries to overheat, leak,
and / or explode.

▪ Batteries must be kept within their recommended temperature

limits (ambient battery temperature range: 32 °F to 131 °F /
0 °C to 55 °C).

▪ New and old batteries and different brands of batteries should

not be used together. Mixing of various batteries can cause
the batteries to overheat, leak, and / or explode.

ON / OFF

Up / HIDown /LO

STANDBY MODE (PILOT FLAME)
▪ Press and hold the "–" button to set

appliance to pilot ame

FLAME HEIGHT ADJUSTMENT

▪ To increase ame height press and

hold "+" button.

▪ To decrease ame height or to set ap-

pliance to pilot ame, press and hold

"–" button.

DESIGNATED LOW FIRE AND HIGH FIRE

▪ To go to hi re, double-click "+" button.
▪

To go to low re, double-click "–" button.

NOTE: Flame goes to high re rst be-

fore going to low re.

Figure 23: 3-button layout

22 / 30

If the appliance will not operate, follow the instructions “TURN
OFF GAS TO APPLIANCE”

(see page 10)

.

© 2019 Mertik Maxitrol GmbH & Co. KG, All Rights Reserved.