Mertik Maxitrol and KG B6RHAS Users Manual
INSTALLATION AND OPERATING INSTRUCTIONS FOR OEM USE ONLY
ON-OFF
UP
DOWN
DRAFT 21/11/2018
RECEIVER FOR POWER FLUE CONTROL, FAN, LIGHT / DIMMER, LATCHING SOLENOID, AUX (VOLT-FREE CONTACT)
Wall Switch (optional)
G6R-ZWSE(N)…
Latching Solenoid Valve
Solenoid Valve
(Required for Power Flue Control)
Main Burner 1Main Burner 2
Pilot Burner
G30-ZP2M-L
Gas Combination
Control
GV60…
G6R-CL40 (50 V / 0.6 A)
G6R-CLB40 (240 V / 5 A)
Receiver
B6R-R8(9)P…
V Module G6R-BUMV3
For Relay with Cable strain reliefs
required, min. 30 N.
(to be mounted by installer)
Maxitrol. The Power Flue Control operates the fan and the solenoid valve and checks the pres-
sure switch. When there is the required draft, the solenoid valve opens. For safety, the solenoid
valve must close in case of power outage.
▪ Power Flue Control, solenoid valve, fan and pressure switch are not available from Mertik
the pilot gas position and stops it at shut off and in pilot position.
▪ The B6R starts the Power Flue Control with the ignition sequence and when the motor leaves
Figure 29
28 / 29
Fan
Draft
Switch
LightFan
Relay with Cable (volt-free contact)
Start
Power Flue Control
(not available from
Mertik Maxitrol)
in
Mains Power
(115 / 230 V; AC)
the Solenoid Valve has to close both burners. If the Solenoid Valve is installed upstream of the
Power Flue Control
▪ The receiver has an additional connection to start the power ue control.
valve a pilot gas position would not be possible.
▪ With a bistable relay at the cable the receiver controls the start function of a Power Flue Control.
▪ A solenoid valve must be installed downstream from the GV60. In case a 2nd burner is installed,
© 2018 Mertik Maxitrol GmbH & Co. KG, All Rights Reserved.
INSTALLATION AND OPERATING INSTRUCTIONS FOR OEM USE ONLY
Symax Handset
B6R-H8(9)…P…D…
The Puck – Handset
B6R-H8(9)SP…
Mobile Device
with myfire App
REQUIRED HANDSET
DRAFT 21/11/2018
MYFIRE APP SETUP
Home Network
Gas Combination
Control
GV60…
Thermocurrent Cable TC
Thermocurrent Cable SW
with ON/OFF Switch
G60-ZSKS(L)S…
G60-ZKIRS…
8 Wire Cable
G6R-C…
UP
Receiver
B6R-R8(9)P
DOWN
ON-OFF
B6R-R8(9)PT
Wall Switch (optional)
G6R-ZWSE(N)…
Cable
G60-ZCSW2…
Mains Adapter (optional)
G60-ZMA3
RGB 2 Phoenix, MC 1,5/3-ST-3,5
ENGLISH
Main Burner
Pilot Burner
G30-ZP2M
Cable
G6R-CBV…
V Module (optional)
G6R-BU(E)…
Interrupter Block
G60-ZUS…
Ignition Cable G60-ZKIS…
Relay with Cable
(volt-free contact)
G6R-CL… (50 V/0.6A)
G6R-CLB… (240 V/5A)
AUX
Temperature Sensor (optional)
G60-ZCT…
115/230 V; AC
Mains Power
Fan
4 levels from
60 % to 100 %
Light
20 % to 100 %
Infinitely variable
14 to 100 Watt
0 to 100 Watt
lights or 12 V lamps a
NOTE: To connect LED
myfire Wi-Fi Box
B6R-W2(XX)-(2)-(T)
is needed.
driver/transformator
5 V - 24 V DC
RGB Power Input
WS2811/12 Standard
LED Driver / Transformer
RGB 1 Phoenix, MC 1,5/3-ST-3,5
Provided by OEM.
© 2018 Mertik Maxitrol GmbH & Co. KG, All Rights Reserved.
Figure 30
(optional)
(optional)
OR
C
º
-11
(Android/iOS)
29 / 29
INSTALLATION AND OPERATING INSTRUCTIONS FOR OEM USE ONLY
DRAFT 21/11/2018
NOTES
© 2018 Mertik Maxitrol GmbH & Co. KG, All Rights Reserved.
Loading...