Merlin E940M, E943M, E945M, E950M, E128M User Manual

Single Button Remote Control
Model E940M

3-Button Remote Control
Model E943M

TO ERASE ALL CODES FROM MEMORY

TRANSMITTERS & WIRELESS WALL CONTROL

MODELS E940M , E943M, E945M, E950M, E128M & E138M

Press and hold the button on
the remote control or wireless
wall control you wish to use. The
LED indicator on
the transmitter

continuously
(except E945M).

Locate
the learn
button.

Press and
immediately release
the Learn button.

For use with Security 2.0 Garage Door Openers. The code between the
the remote control and the receiver changes with each use, randomly
accessing over a billion new codes. Refer to your product manual for the
location of the learn button.

NOTE: Your product may look

than the products illustrated

in this manual.

When deactivating any unwanted remote
control code, all previous codes will be
erased.

Press and hold the Learn button on garage door opener
until the learn LED goes out (approximately 6 seconds).
All previous codes are now erased. Reprogram each
remote control you wish to use.

LED

LED

PROGRAM USING THE GARAGE DOOR OPENER

+

ROLLER DOOR
OPENER

LEARN
BUTTON

3- Button Mini Remote Control
Model E945M

Wireless Wall Control
Model E128M

“click”

“click”

The opener

or 2 clicks are
heard when
it has learnt
the code.

4

LED

LED
INDICATOR

SECTIONAL DOOR
OPENER

LEARN
BUTTON

LED
INDICATOR

•

•

•

To prevent possible SERIOUS INJURY or DEATH from a moving gate or garage door:

ALWAYS keep remote controls out of reach of children. NEVER permit children to operate, or play with remote controls.

Activate gate or door ONLY when it can be seen clearly, is properly adjusted, and there are no obstructions to door travel.

ALWAYS keep gate or garage door in sight until completey closed. NEVER permit anyone to cross path of moving gate or door.

4-Button Remote Control
Model E950M

LED

LED

Wireless Wall Control
Model E138M

REPLACEMENT PARTS

CR2032 Lithium battery - CR2032
Visor Clip - 029B137

ONE YEAR LIMITED WARRANTY

3-BUTTON REMOTE CONTROLS

Press and hold the button down until the door or gate
starts to move. The remote control will operate from
up to 3 car lengths away on typical installations.
Installations and conditions vary, contact an installing
dealer for more information.

HOW TO USE THE REMOTE CONTROL

Additional buttons on the remote control can be
programmed to operate up to 3 devices such as
additional garage door openers, light controls, gate
operators or access control systems.

3V2032

in the middle (1), then
at each side (2 and 3)
with the visor clip.

Remove the old battery.
Dispose of old batteries
properly.

Insert replacement
batteries positive side up.
Replace the batteries
with only 3V2032
coin cell batteries.

Replace cover.

THE REMOTE CONTROL BATTERY

The lithium battery should produce power for up to 5 years. If the battery is low, the remote control's LED will
not when the button is pressed. To replace battery:

To prevent possible SERIOUS INJURY or DEATH:

• NEVER allow small children near batteries.
.rotcod yfiton yletaidemmi ,dewollaws si yrettab fI •

To reduce risk of

explosion or chemical burn:

• Replace ONLY with 3V2032 coin batteries.

.etarenicni ro )C °001( F °212 evoba taeh ,elbmessasid ,egrahcer TON OD •

1

2

3

114A4382C

CR2032

Use a screwdriver
blade to pry open the
case as shown

Remove the old battery.
Dispose of old batteries
properly.

Insert replacement
batteries positive side
up. Replace the
batteries with only
CR2032 coin cell
batteries.

Replace cover.

CR2032

Use a screwdriver
to open the case as
shown

Remove the old battery.
Dispose of old batteries
properly.

Insert replacement
batteries positive side
up. Replace the
batteries with only
CR2032 coin cell
batteries.

Replace cover.

The Chamberlain Group, Inc. warrants to the original consumer purchaser of this
product that it is free from defect in materials and/or workmanship for a period of
1 year from the date of purchase.

CR2032

Use a screwdriver
blade to pry open the
case as shown

Remove the old battery.
Dispose of old batteries
properly.

Insert replacement
batteries positive side
up. Replace the
batteries with only
CR2032 coin cell
batteries.

Replace cover.

+

+