Merlin Condor 1380 Instruction Manual

INSTRUCTION MANUAL

ML41025

English - 2-10
Deutsch - 11-19
Français - 20-28
Español - 29-37

We know you will have great fun with your model, but to get the best from your purchase please read this information BEFORE you operate the
model

Table of contents Page

Warranty ………………………………………………………..….. 2
Introduction……………………………………………………………….. 3
Specifications……………………………………………..……… 3
Items required for operation……………………………...…… 3
Glossary…………………………………………………………. 3
Safety precautions……………….…………………………..…. 3
Recommended tools…………………………………………… 3
Charging the battery pack…………………………………….. 3
Transmitter……………………………………………………………..… 4
Preparing the transmitter……………………………………… 4
Throttle stick…………………………………………………….. 4
Elevator stick……………………………………………………. 4
Rudder stick…………………………………………………….. 4
Assembly Guide……………………………………………………….… 5
Trimming Adjustments and Control Test……………………..……. 7
Making trim adjustments to the horizontal stabiliser & rudder 7
Motor test………………………………………………………… 7

Flight Controls ……………………..………………………………….... 8

Motor…………………………………..………….………………. 8
Elevator…………………………………..…………………..…… 8
Rudder………………………………….…………………..…….. 8
Pre-flight Checklist and Control Test……………………………..…. 8
Checklist…………………………………………………………. 8
Control test………………………………………………………. 8
Range test……………………………………………………….. 8
How to Fly……………………………………………………………..…. 9
Experience……………………………………………………….. 9
Site and conditions………………………………………………. 9
Taking off…………………………………………………………. 9
Turning and flying………………………………………………... 9
Landing……………………………………………………………. 9
Tips for success………………………………………………….. 9
Helpful Information..………….………………………………….…. 10

HAVE FUN! But please read this first !!

2

Warranty

90 Day Component Warranty

We want you to enjoy your Merlin Flight Product, but please read this first!

This product is covered by a 90 day component warranty from date of purchase. If any part of the product fails as a result of faulty manufacture
during this period then we will repair or replace that part at our discretion.

We do not operate a new for old warranty once the product has been used.

Please note this product is not a toy and it is recommended that children 14 and under are supervised by an adult. It is the responsibility of the
parent or guardian to ensure minors are given appropriate guidance and supervision.

If you suspect there is a problem with the product, for whatever reason, it is the user’s responsibility to investigate and take steps to rectify the
problem before further damage occurs.

Not Covered By Warranty

This is a sophisticated, high performance model and should be treated with care and respect. Every effort has been made to make this product as
strong and durable as possible, however due to the nature of this product, it is still possible to break or damage parts through crashing or extreme
use. Components damaged as a result of crash damage, improper use, lack of maintenance or abuse are not covered by the warranty.

How to Claim Against your Warranty

For warranty claims please first contact your supplying retailer. Do not return the product to your distributor without their prior approval. You may
not need to return the product in full, only the damaged component along with a copy of your purchase receipt. In many cases it is faster and more
cost effective for the user to fit the replacement part(s) to the product & therefore we reserve the right to supply parts only in these instances.

Any returned component that is inspected by your distributor and found to have an invalid warranty claim may be subject to an inspection and
handling fee before it can be returned. Any repairs required as a result of neglect or misuse will be charged before any work is carried out on the
product. If you decide not to have any work carried out the distributor reserves the right to charge a handling and a shipping fee. The level of these
fees are at the discretion of the distributor.

Please attach your proof of purchase in the manual as you may need it again in the future.

Items required for operation

8 * AA Batteries for the Transmitter

3

Specifications

General Safety Precautions

• Read and follow this manual completely, observing all instructions and safety directions. Otherwise, serious injury and damage can occur.

Think about your safety, and the safety of others, first.

• Hold the aeroplane securely when the flight battery is plugged in, keep the propeller away from body parts and clothing, even when it isn’t

spinning, as it could be turned on by accident. Beware of hair becoming en-tangled in the propeller, especially while launching your aero
plane.

• Do not fly when it’s too windy or you may lose control and crash, causing injury or damage. Never fly near people, vehicles, train tracks,

buildings, power lines, water, hard surfaces or trees. Never allow anyone to attempt to catch the aeroplane while it’s in flight or serious
injury may result.

• Adult supervision for flying and battery charging is recommended for pilots age 14 and younger.

• Only use a battery charger that is Ni-MH compatible to charge the flight battery. Never leave the charger unattended while charging.

This will help prevent overcharging and make sure damage does not occur to the battery, charger or any other property. While charging,
place the battery on a heat-resistant surface. Do not lay it on carpet or upholstery while charging.

• Never cut into the battery, charger, or aeroplane wires or serious injury may occur. Causing the battery to “short out” (crossing negative

and positive bare wires) can cause fire, serious injury and damage.

• When you finish flying your aeroplane, always unplug the battery before you turn off the transmitter.

• Never fly on the same frequency as another RC aeroplane in your area. The frequency of the aeroplane is shown on the frequency crys

tals.

Recommended Tools

These tools are not included with the product but are recommended for use whilst working or repairing your product :­ Foam Safe Super Glue Mini Phillips Screwdriver Packing Tape

Charging the battery pack

Use the supplied charger to charge the supplied battery. Other products are available and if used, you must follow the products instructions to
avoid damage.

The charging time for the battery is 300 minutes.

1. Connect the 240V wall mounted mains charger.

2. Plug the battery into the charge lead connector.

3. When the battery is warm it is charged noting the charge time.

4. Unplug the battery from the charger when finished.

Cautions

• Use the charger with adult supervision. Do not use the charger near water or when wet.

• Do not use the charger if the wire is frayed or worn. If the wire is frayed or worn a short circuit can cause a fire or burns.

• If your battery gets hot and exceeds 50 degrees C during charge it may be faulty and should be replaced.

• If the battery pack bulges during charge or use it is faulty and should be replaced.

• Never leave your battery on charge unattended.

Introduction

Glossary

Landing gear - Wheels on bottom of aeroplane
Vertical fin - Fin on back of aeroplane
Rudder - Moveable fin on vertical fin
Elevator - Moveable fins of the stabiliser
Fuselage - Main body of the aircraft containing motor, receiver, speed control, servos and battery
Stabiliser - Smaller flat wing on tail of aircraft

Wingspan 1380mm

Transmitter MTX-41 35 MHz 4 Channel
Fuselage Length 900mm Receiver MRX-41 35 MHz 4 Channel

Flying Weight 578g Charger Mains 240V 9V 280mah

Motor 370 Size brushed Servos 2.2Kg.cm 0.2s/90Deg 18g

Battery Ni-MH 8.4V 1300 mAh

Speed Control Brushed 15A 7.2-8.4V

Flight Time Approx 20 minutes

4

The Merlin MTX-41 Transmitter is an advanced controller designed for the beginner to be easy to use and tune. You will need to follow the steps
below to ensure you prepare the controller correctly for use and understand the adjustment possibilities available.

Elevator Stick

Insert 8 AA batteries into the
marked spaces. Please note the
correct direction of the batteries

Incorrect battery insertion could
lead to damage

Preparing the transmitter

Insert the aerial into the hole and
turn clockwise until it is tightly
secured.

Make sure you never over extend
the aerial as this will cause it to
break.

Open the battery holding tray to
expose the empty battery slots.

1. Aerial

2. Throttle Trim

3. Rudder Trim

4. Elevator Trim

5. Throttle Stick

6. Rudder/Elevator Stick

7. Power Switch

8. Battery level indicator

9. Not Used

10. Rudder reverse switch (labelled AIL)

11. Throttle reverse switch

12. Elevator reverse switch

13. Frequency Crystal

Throttle Stick

Rudder Stick

1. Push the stick forward
to increase propeller
speed

2. Pull the stick back­wards to decrease
propeller speed

1

4

7

2

3

5

6

9 8 10 11 12

13

1

2

1

2

1

2

1. Push the stick left to turn
left, rudder moves left

2. Push the stick right to
turn right, rudder moves
right

1. Push the stick forward to
lower the nose, elevator
moves down

2. Pull the stick backwards to
raise the nose, elevator
moves up

Transmitter

5

Bend the landing gear and install it to the
landing gear slot under the fuselage

Slide the propeller onto the motor shaft

Tighten the propeller with the 1.5mm wrench
provided

Pre assemble main wings by inserting the
wing strengthening tube into the hole on the
main wings

Ensure the tube is fully inserted so the wing
halves make contact

Disassemble and reinsert the main wings
over the tube from each side of the fuselage

1

2

3 4

5 6

Assembly Guide

6

Remove the backing of the double sided
tape on the vertical fin and install it to the
stabiliser

Remove the backing of the double sided
tape on the bottom of the stabiliser

Carefully widen the tail of the fuselage by
2 -3 mm

Insert the fin and stabiliser into the tail of the
fuselage pressing firmly to ensure double
sided tape adheres

Insert the pushrod clips into the middle hole
on the vertical fin and stabiliser arms

After assembly check the symmetry and
alignment of the main wing and tail

Open the canopy as shown above

Ensuring the power switch is OFF plug in
and install the battery

7 8

9

10

11

12

13 14

7

Making Trim Adjustments to the Horizontal Stabiliser & Rudder

1. Make sure the throttle stick is in the “off” position by pulling it fully back.

2. Turn on the transmitter and check the LED power lights come on.

3. Set the elevator & rudder trim levers to the centre.

4. Turn on the aeroplane making sure the battery is plugged in and/or turned on.

5. The control surfaces should move as the control sticks are moved.

6. Make certain the elevator is set to neutral and is flat with the horizontal stabiliser. Do this by removing the clevis from the control horn and
turning it on the threaded pushrod as needed. Once the adjustment is made, re-attach the clevis.

7. Make certain the rudder is set to neutral and is flat with the tail fin. Do this by removing the clevis from the control horn and turning it on
the threaded pushrod as needed. Once the adjustment is made, re-attach the clevis.

8. If for any reason the controls move in opposite directions to those explained in the transmitter functioning then change the position of the
relevant reverse switch on the transmitter.

1 & 2

5

3

4

It is important that the control surfaces of your aeroplane are correctly set for it to fly correctly.

Warning: Keep everything clear of the propeller before starting the tests so you do not damage any property or harm anyone.

Motor Test

With the transmitter and aeroplane already switched on from above

1. Hold the aeroplane firmly by its fuselage and keep everything clear of the propeller.

2. Press the red motor power switch button.

3. Push the throttle stick forwards slowly and the propeller should spin at speed.

4. When finished with the motor test, switch off the aeroplane before disconnecting the battery and then turn off the transmitter. Follow this
step each time you need to turn the aeroplane off.

5. If for any reason the motor operates on full power with the control stick pulled backwards and is off in the forward position then switch off

the power and change the position of the relevant reverse switch on the transmitter. Then re-test as above

Trimming Adjustments and Control Tests

8

Using the Motor

The motor is used to control the flying speed and rate of climb of the aeroplane

• Initial take off and climb to minimum altitude is carried out at full power.

• To achieve and maintain a level “cruising” altitude, reduce the power by moving the throttle stick down to

approximately 70% of full on. The throttle stick is proportional, so you can add or reduce throttle in small
increments as needed to maintain the altitude that you desire.

• To reduce altitude you need to reduce the throttle, and to increase altitude you need to increase the throttle.

Range Test

1. Leave the aeroplane and walk 100 paces away whilst checking the control functions are still working.

2. If you can see or hear the control functions are still working then the range test is complete.

3. If the control functions do not work to your commands at 100 paces, do not attempt to fly your aeroplane and refer instead to the trouble­shooting section of this manual.

Using the Rudder

The rudder is used to control the turning of your aeroplane.

• When airborne and at an acceptable level moving the rudder stick will make your aeroplane turn left or right. Once the aeroplane has

begun to turn then return the stick to neutral or if necessary apply a small amount of opposite turn to resume straight flight.

• Excessive or prolonged use of the rudder can cause the nose to drop and the aeroplane to turn too tightly.

Using the Elevator

The elevator is used to control the pitch (level) of the aeroplane. In normal flight small adjustments of the elevator are used to maintain even level
flight.

• Pushing forwards on the elevator stick makes the nose lower and the speed to increase entering a dive.

• Pulling back on the stick provides up elevator making the nose rise and flight speed slow. Pulling too far back on the elevator and climbing

too quickly will cause the aeroplane stall. To avoid crashing from a stall, always maintain enough altitude to recover. Just after a stall has
occurred, the nose of the aeroplane will fall and the aeroplane will look like it is diving. To pull out of a stall, simply pull back slowly on the
elevator stick until level flight is resumed. Pulling back too quickly or for too long will once again cause the aeroplane to enter a stall.

Each time before you start flying your Merlin Flight Product please carry out the following check checks and test.

Checklist

• Control surfaces have free movement

• All screws, bolts, etc. are tight

• Radio equipment is securely fastened inside fuselage

• Batteries are fully charged

• No wires interfere with servo motors

• Antenna is properly strung

• Wings are securely fastened

• Looking from the rear of the aeroplane to the front make sure that the wings and tail are not damaged and are correctly aligned to the

fuselage.

Control Test

Warning: Keep everything clear of the propeller before starting the control test in the event that you accidentally turn on the motor.

1. Be certain that the throttle stick is in the “off” position and that both trim levers are centred.

2. Switch on the transmitter and check to make sure the green LED is lit, indicating the transmitter has power. If the red LED is lit then trans

mitter batteries are low on power and must be replaced before flying.

3. Install the flight battery into the fuselage and plug it into the battery connector, switch on the aeroplane power switch and press the motor

power switch.

4. Move the transmitter control sticks. The control surfaces should move as per your transmitter input.

5. Move the throttle stick forwards, the propeller should spin.

Flight Controls

Pre-Flight Checklist and Control Test

9

Landing

When you begin to notice that your Merlin Product no longer climbs well under full power the battery is getting low and it is time to land.

1. Bring your aircraft directly into the wind and toward the desired landing spot.

2. Gradually reduce throttle (and give a small amount of down elevator if you choose) to reach an altitude of approximately 3 metres.

3. At this point, reduce the throttle to zero and your aeroplane should glide in softly for a landing.

Site and Conditions

• Don’t fly in winds over 8 mph! If you are a less experienced pilot, this is especially important.

• Choose your flying field carefully - grass and soft ground with a 150-metres diameter of open space is ideal. Make sure there are no ob

stacles that will get in your way when flying, such as trees or buildings. Make sure you do not fly where there are pedestrians who could
be hurt by the aeroplane.

• Position yourself at your flying field so that you keep the sun at your back and out of your eyes. Wear sunglasses on bright days.

• Keep your aeroplane in front of you so you don’t have to turn in circles as you fly. Try to avoid flying directly overhead.

• Keep the aircraft upwind, especially on windier days, to prevent it from “flying away”

Experience

A pilot who has never flown an aeroplane at all will find it easier if an experienced radio control pilot is present to guide them but by carefully fol­lowing the manual’s basic instructions, flying skills can be learnt and mastered.

Tips for Success

• The flight of your aeroplane may change as you enter into or fly with the wind causing the nose to rise or fall, especially in more windy

conditions. To maintain a more controlled flight be prepared to adjust the elevator control to keep the nose of the aeroplane level whilst
turning.

• If your aeroplane continues to turn left or right with the control stick in neutral position, you can apply a small amount of opposite trim by

moving the appropriate trim lever whilst still in flight.

• If when gliding your aeroplane or on low power settings it continues to dive, then adjust the trim lever on the elevator backwards to obtain

level flight.

• If when gliding your aeroplane or on low power settings it continues to stall, then adjust the trim lever on the elevator forwards to obtain

level flight.

• Note that the control range is 750 metres. Do not allow the aeroplane to get too far away from you. When the aeroplane is further away it

is harder to see and the higher you fly, the more the aeroplane will be affected by wind.

• If you’re gliding with the motor off, allow your aeroplane more area for turns.

• Remember that holding the stick full over for too long can cause the aeroplane to spiral dive and crash. At the very first sign of the aero

plane beginning to spiral down, immediately release the stick and give the opposite turn control to the spiral, then pull back on the elevator
gently to level flight and level the wings.

• Don’t attempt to fly or do manoeuvres beyond your flying abilities. Seek the assistance of an experienced pilot when trying new manoeu-

vres that are more extreme and involve fast flight.

• Damage/bends to the wings or tail can greatly affect flight control. Replace damaged parts immediately.

• As you get better and more experienced at flying, try adding a bit of “up” elevator just prior to landing to “flare” the aeroplane. With some

practice, your landings should become smooth and on target.

Taking Off

Your Merlin aeroplane can take off from a smooth ground however we recommend first flights to be hand launched. This can be carried out by the
pilot alone but is easier with two people, one launching the aeroplane and the other at the controls.

1. While holding the transmitter in one hand, push throttle stick to full on (up).

2. Hold your aeroplane with your other hand, take a couple of steps and firmly launch directly into the wind while keeping the wings level. Do

not throw it up or down. Point it level (parallel) with the ground when releasing.

3. Keep steering into the wind and hold at full throttle in a slight climb Do not try to climb too fast by pulling all the way back on the elevator
stick or your aeroplane may stall. You should climb by giving small amounts of elevator.

4. When you have reached an altitude of at least 15 to 20 metres it is safe to steer in the desired direction, as well as adjust the throttle

input, to help control altitude and speed.

How to Fly

Turning and Flying

1. Before your aeroplane becomes too distant begin turning by moving the rudder stick gently.

2. Avoid holding the rudder stick on full right or full left for more than two seconds, as this will cause the aeroplane to enter a spiral dive that
could cause you to crash.

3. Once a normal flight altitude of 15-50 metres has been achieved reduce the throttle stick to 50-75 % of full power. This will prevent your
aeroplane climbing further, make it easier to control and lengthen the flight time.

4. Practice control by turning in large circles.

5. To make your aeroplane descend reduce the throttle stick to 0-25 % of full power and it will enter a glide. A small amount of up elevator

may be needed to keep the plane level and prevent it gaining too much speed.

Parts Listing

10

Troubleshooting

Problem Cause Solution

Unit does not operate Transmitter “AA” batteries are depleted or

installed incorrectly, indicated by a dim or unlit
LED on transmitter or the low battery alarm.

Check polarity installation or replace with fresh “AA”
batteries.

No electrical connection. Push connectors together until they “click.”
Flight battery not charged. Charge battery fully.
Crash has damaged the receiver inside. Replace the fuselage or receiver.

Aircraft keeps turning in one direction Rudder or rudder trim is not adjusted correctly. Adjust rudder and/or rudder trim.

Damage to vertical fin. Make sure vertical fin is at 90 degrees from elevator.

Aircraft is difficult to control Wing or tail is damaged. Replace damaged part.
Aircraft will not climb Battery is not fully charged. Charge battery fully shortly before flying.

Elevator trim may be incorrect. Adjust elevator trim.

Aircraft keeps pitching up steeply Wind is too gusty or strong. Postpone flying until the wind calms down.

Elevator trim may have raised too much. Trim elevator down with the transmitter trim or

threaded linkage.

Aircraft control range is limited or
interference is experienced

Transmitter batteries are low on power. Check for defective batteries and replace.

Other models are being used on the same
frequency.

Change crystal frequency to a different number.

Transmitter aerial not fully extended. Fully extend transmitter aerial.

Helpful Information

Receiver and Servo Wiring

Under normal circumstances there should be no need to unplug any of your aeroplanes wiring, however for reference purposes the receiver is
wired as follows.

Channel 1 = unused
Channel 2 = rudder servo
Channel 3 = electronic speed control (propeller)
Channel 4 = elevator servo

Your Merlin product is supplied with a transmitter labelled and suitable for 4 channel models. However for 3 channel operation the rudder is usu­ally controlled form the right hand control stick (known as mode 2) which is labelled AIL for ailerons.

Repairing Minor Damage

If you happen to crash, and part of the tail or wing breaks, you can repair the damage by using packing tape or Foam Safe super glue to repair
and cover the missing pieces. However, if the damage is severe, or if the wings and/or tail are bent, replace the damaged parts prior to flying
again. See the last few pages of the manual for a complete list of replacement parts for your Merlin Flight Product. To ensure that you minimise
the chances of any potential problems whilst using your Merlin Product we always recommend replacing any parts that look to be damaged before
use.

Part No Description

Part No Description

ML41001 MTX-41 4 Channel. Transmitter

ML41009 Charger 240V (UK 3-Pin)

ML41002 MRX-41 4 Channel. Receiver ML41010 Charger 240V (EU 2-Pin)

ML41003 Servo 2.2Kg.cm 0.2s/90Deg 18g ML41011 370 Size Brushed Electric Motor

ML41004 Motor Speed Controller 15A 7.2-8.4V ML41012 Landing Gear Condor 1380

ML41005 Main Wing Condor 1380 ML41013 Tail Assembly Condor 1380

ML41006 Fuselage Condor 1380 ML41025 Merlin Condor 1380 Instructions & Parts Manual

ML41007 Propeller Condor 1380

ML41026 Battery Cover

ML41008 Battery Ni-MH 8.4V 1300 mAh Condor 1380

11

Garantie

90-Tage-Garantie auf Komponenten

Für dieses Produkt gilt eine 90-Tage-Garantie auf Komponenten ab dem Kaufdatum. Wenn während dieser Zeit ein Teil des Produkts infolge
Fabrikationsmängeln ausfallen sollte, liegt es in unsrem Ermessen, ob wir das Teil reparieren oder austauschen.

Wenn das Produkt einmal benutzt wurde, bieten wir keine Neu-für-Alt-Garantie.
Beachten Sie bitte, dass dieses Produkt kein Spielzeug ist und dass Kinder unter 14 Jahren von einem Erwachsenen beaufsichtigt werden sollten.

Es liegt in der Verantwortung der Eltern oder Aufsichtspersonen, sicherzustellen, dass Minderjährige entsprechende Anleitung und Aufsicht erhal­ten.

Bei der Vermutung eines Problems mit dem Produkt, aus welchem Grunde auch immer, ist der Benutzer dafür verantwortlich, das Problem zu
untersuchen und für Abhilfe zu sorgen, bevor weitere Schäden entstehen.

Von der Garantie nicht gedeckt

Dies ist ein technisch ausgereiftes Hochleistungs-Modell, das mit Sorgfalt und Respekt behandelt werden sollte. Wir haben zwar alles getan, um
dieses Produkt so stabil und haltbar wie nur möglich zu machen, trotzdem können auf Grund der Natur dieses Produkts Teile bei Zusammen­stößen oder extremem Einsatz beschädigt werden oder brechen. Komponenten, die durch einen Unfall, falsche Verwendung, mangelnde Wartung
und Pflege oder Mißbrauch beschädigt wurden, fallen nicht unter die Garantie.

Garantieansprüche geltend machen

Mit Garantieansprüchen wenden Sie sich bitte zuerst an Ihren Händler. Ohne vorherige Genehmigung das Produkt nicht an den Distributor ein­schicken. Sie brauchen das Produkt nicht als Ganzes einschicken, nur die beschädigte Komponente zusammen mit einer Kopie des Kaufbelegs.
In vielen Fällen ist es für Sie schneller und kostengünstiger, Ersatzteile in das Produkt einzubauen; daher behalten wir uns das Recht vor, nur in
solchen Fällen die Ersatzteile zu liefern.

Für jede eingeschickte Komponente, bei deren Überprüfung Ihr Distributor einen ungültigen Garantieanspruch festgestellt hat, werden Ihnen vor
der Rücksendung möglicherweise Prüfungs- und Bearbeitungskosten in Rechnung gestellt. Reparaturen, die als Folge von Nachlässigkeit oder
Mißbrauch erforderlich sind, werden in Rechnung gestellt, bevor Arbeiten am Produkt durchgeführt werden. Wenn Sie sich entscheiden, dass
keine Arbeiten ausgeführt werden sollen, hat der Distributor das Recht, Bearbeitungs- und Versandkosten in Rechnung zu stellen.

Sie sollten Ihren Kaufbeleg an dieses Handbuch anheften, für den Fall, dass Sie ihn später noch einmal benötigen.

Wir wissen, dass Sie mit Ihrem Modell viel Spaß haben weden, aber BEVOR Sie das Modell in Betrieb nehmen, lesen Sie bitte erst diese Informa­tionen, damit Sie das Beste aus Ihrem Kauf machen können

Inhaltsverzeichnis Seite

Garantie…………………………………………………………...…..... 11

Einführung……………..………………………………………...….…. 12
Technische Daten……………………….…………………… 12
Für den Betrieb erforderlich………………………………….. 12
Glossar…………………………………………………………. 12
Allgemeine Sicherheitsmaßnahmen…………………….….. 12
Empfohlenes Werkzeug……………………………………… 12
Batteriepack aufladen……..………………………………….. 12
Sender……………………………………..……………………………. 13
Vorbereiten des Senders………………………………….…. 13
Drosselhebel…………………………………………………... 13
Höhenruderhebel……………………………………………... 13
Seitenruderhebel………………………………………………. 13
Zusammenbauanleitung……………………………………………... 14
Trimmeinstellungen und Steuerungstests……...……………... 16
Trimmeinstellungen am Horizontalstabilisator und Seitenruder 16
Motortest.………………………………………………………. 16

Flugsteuerung……………………..………………………………..... 17

Motor………………………………………………………….... 17

Höhenruder………………………………………………….…. 17
Seitenruder………………………………………………..…… 17
Checkliste und Steuerungstest vor dem Flug……………………. 17
Checkliste……………………………………………………… 17
Steuerungstest………………………………………………… 17
Reichweitentest……………………………………………….. 17
Fliegen…………………………………………………………………... 18
Erfahrung………………………………………………………. 18
Ort und Bedingungen………………………………………… 18
Starten…………………………………………………………. 18
Kurvenfliegen……………………………………………...….. 18
Landen…………………………………………………………. 18
Tips für den Erfolg…………………………………………….. 18

Nützliche Informationen..………….………………………………...... 19

VIEL SPASS! Aber lesen Sie bitte erst diese Anleitung !!

Für den Betrieb erforderlich

8 * AA Batterien für den Sender

12

Technische Daten

Einführung

Glossar

Landefahrwerk - Räder unten am Flugzeug
Heckflosse - senkrechte Flosse hinten am Flugzeug
Seitenruder - beweglicher Teil der Heckflosse
Höhenruder - Bewegliche Klappen an den hinteren Tragflächen (Stabilisator)
Rumpf - Körper des Flugzeugs, enthält Motor, Empfänger, Geschwindigkeitssteuerung, Servoantriebe und Batterie
Stabilisator - Kleine flache Tragfläche am Heck des Flugzeugs

Sicherheitsmaßnahmen

• Dieses Handbuch vollständig durchlesen und alle Anweisungen und Sicherheitshinweise befolgen. Sonst kann es zu schweren Unfällen

und Sachschäden kommen. Denken Sie zuallererst an Ihre Sicherheit und die Sicherheit anderer.

• Halten Sie beim Anschließen der Flugbatterie das Modell sicher fest; den Propeller vom Körper und der Kleidung fernhalten, auch wenn

er nicht rotiert, denn er könnte zufällig eingeschaltet werden. Achten Sie darauf, dass - besonders beim Starten des Modells - sich das
Haar nicht im Propeller verfängt.

• Nicht fliegen, wenn es zu windig ist - Sie können leicht die Kontrolle verlieren und bei einer Bruchlandung sind Verletzungen oder

Sachschäden möglich. Nicht in der Nähe von Personen, Fahrzeugen, Eisenbahnschienen, Gebäuden, Stromleitungen, Wasser, harten
Flächen oder Bäumen fliegen. Nie zulassen, dass jemand das Modell im Flug zu fangen versucht - schwere Verletzungen können die
Folge sein.

• Bei Fliegen und Aufladen der Batterie wird für Piloten unter 14 Jahren Aufsicht durch einen Erwachsenen empfohlen.

• Nur ein mit der Flugbatterie kompatibles Ladegerät verwenden. Beim Aufladen das Ladegerät nie unbeaufsichtigt lassen. Damit wird

Überladen der Batterie verhindert und sichergestellt, dass Batterie, Ladegerät oder andere Gegenstände nicht zu Schaden kommen.
Während des Aufladens die Batterie auf einer hitzebeständigen Unterlage ablegen, nicht auf Teppichen oder Polstern.

• Nie in Batterie, Ladegerät oder Kabel schneiden - ernsthafte Verletzungen können die Folge sein. Kurzschließen der Batterie (blanker

Draht zwischen Plus- und Minuspol) kann Brand, ernsthafte Verletzungen und Sachschäden verursachen.

• Nach dem Fliegen des Modells immer erst die Batterie abklemmen, und dann erst den Sender ausschalten.

• Nie das Produkt mit der gleichen Fernsteuerfrequenz verwenden wie ein anderes funkgesteuertes Modell in der Nähe. Die Frequenz des

Modells ist auf den Schwingquartzen angegeben.

Empfohlenes Werkzeug

Diese Werkzeuge werden mit dem Produkt mitgeliefert, sind aber für Arbeiten an diesem Produkt empfohlen :-

Schaumstoff-Superkleber Miniatur-Schraubendreher Pack-Klebeband

Batteriepack aufladen

Zum Aufladen der mitgelieferten Batterie das mitgelieferte Ladegerät verwenden. Wenn andere handelsübliche Produkte verwendet werden, zur
Vermeidung von Schäden die zugehörigen Anweisungen befolgen.

Die Ladedauer für die Batterie beträgt 300 Minuten.

1. Das Stecker-Ladegerät in eine 240V-Wandsteckdose stecken.

2. Die Batterie an den Stecker des Ladekabels anschließen.

3. Wenn die Batterie warm ist, ist sie aufgeladen; die Ladedauer beachten.

4. Die aufgeladene Batterie vom Ladegerät trennen.

Vorsichtshinweise

• Das Ladegerät nur unter Aufsicht eines Erwachsenen verwenden. Das Ladegerät nicht nass oder in der Nähe von Wasser verwenden.

• Das Ladegerät nicht verwenden, wenn das Kabel ausgefranst oder abgescheuert ist. Bei einem ausgefransten oder abgescheuerten

Kabel kann leicht ein Kurzschluß auftreten und Feuer oder Verbrennungen verursachen.

• Wenn Ihre Batterie heiß wird und während des Aufladens 50°C überschreitet, könnte sie defekt sei - wenden Sie sich in diesem Fall bitte

an Ihren Händler.

• Wenn während des Aufladens und beim Betrieb das Batteriepack anschwillt oder expandiert, ist es defekt - wenden Sie sich in diesem

Fall bitte an Ihren Händler.

• Die Batterie am Ladegerät nie unbeaufsichtigt lassen.

Flügelspannweite 1380mm

Sender MTX-41 35 MHz 4 Ch

Rumpflänge 900mm

Empfänger MRX-41 35 MHz 4 Ch

Gewicht 578g

Batterieladegerät 240V / 9V 280mah
Motor 370er Elektro-Bürstenmotor Servo 2.2Kg.cm 0.2s/90Deg 18g
Batteries Ni-MH 8.4V 1300 mAh

Geschwindigkeitsregler Bürsten 15A 7.2-8.4V
Ungefaehre Flugzeit 20 Minuten