How it Works
Meridian Audio
Loading...
SRC-2010
Brochure
1 pgs418.22 Kb0
Owners manual
1 pgs177.82 Kb0
User Manual
56 pgs699.83 Kb0

Meridian Audio SRC-2010 User Manual

Download
Page 1
SRC-2010
Programmable Remote Operation manual
Page 2
The Smart Remote Control User’s Manual
PrefacePreface
About this manual
This manual is designed to make using the SRC-2010 Smart Remote Control as easy as possible. Information in this document has been carefully checked for accuracy; however, no guarantee is given to the correctness of the contents. The information in this document is subject to change without notice.
The SRC-2010 comes preprogrammed with commands to control various Faroudja products. See each product’s operations manual for details on the available functions. These commands can be changed if using the setup soft­ware from a PC. The original program can be downloaded from www.faroudja.com . For instructions on using the PC setup software, see the Help menu in the software.
Copyright
© Copyright 2003
This document contains proprietary information protected by copyright. All rights are reserved. No part of this manual may be reproduced by any mechanical, electronic or other means, in any form, without prior written per­mission of the manufacturer.
Trademarks
All trademarks and registered trademarks are the property of their respective owners.
Page 3
Table of Contents
Unpacking the Smart Remote Control ................................2
Smart Remote Control features ..........................................3
Identifying components......................................................4
Power supply......................................................................7
Inserting the batteries............................................................................8
Power supply precautions....................................................................9
Power supply tips...................................................................................9
Battery low icon......................................................................................9
The LCD ............................................................................10
Turning the Smart Remote Control on............................................10
Touch screen precautions..................................................................11
The Information screen.......................................................................12
Smart Remote Control buttons.......................................... 13
Direct access buttons..........................................................................13
Touch screen buttons..........................................................................14
The main menu ................................................................ 15
The device menu ..............................................................16
The setup menu ................................................................17
Setting the clock ...............................................................19
Using the timer................................................................. 20
Timer view.............................................................................................21
Timer setup............................................................................................21
Relabeling timers.................................................................................22
Using the program menu.................................................. 23
Using the learning function...............................................................23
Clearing a key......................................................................................26
Clearing a device................................................................................27
Clearing all devices............................................................................27
Changing the LCD layout ..................................................28
Resizing or adding buttons on the main menu...............................29
Relabeling buttons on the main menu.............................................33
Deleting buttons on the main menu.................................................35
Adjusting buttons on the device menu.............................................36
Relabeling device menu buttons.............................................................37
Using recall.............................................................................................38
Using macros.................................................................... 39
Macro setup..........................................................................................40
Relabeling a macro.............................................................................41
Page 4
The Smart Remote Control User’s Manual
Deleting a macro .................................................................................42
The duplicate menu.......................................................... 43
Making LCD adjustm ents ..................................................44
Adjusting the LCD contrast...............................................................45
Adjusting the LCD backlight.............................................................46
Calibrating the LCD...........................................................................47
Specifications ...................................................................48
Troubleshooting................................................................ 50
Page 5
Table of Figures
Page 6
Page 7
Chapter 1Chapter 1
Introducing the Smart Remote Control
Congratulations on the purchase of your SRC-2010 Smart Remote Control. The Smart Remote Control is a digital universal remote control that is easy to use and configure, enabling you to control all your IR equipped electronic de­vices.
One feature of the Smart Remote Control is the touch screen control panel, which reduces the number of buttons on the device, making it easy for you to find the function you want. You can control up to 10 devices, including a VCR, DVD, amplifier, TV, and LD/VCD.
The Smart Remote Control is easy to set up. With the “Learning eye” you can easily configure each device in your household or office. You can also eas­ily edit the device list, make changes to the LCD appearance, and adjust other settings. In addition, with the Macro function, you can initiate a chain of up to 25 commands with the touch of a button.
Most universal remote controls have a set list of devices and static functions that don’t provide you with a lot of flexibility. The Smart Remote Control enables you to add and delete devices, relabel device buttons, and change the size and shape of LCD panel buttons. With this convenient and easy to use Smart Remote Control, you can control all your devices with one remote con­trol solution. No longer will you have to search for several different remotes!
Page 8
The Smart Remote Control User’s Manual
This manual will help you learn how to use all the ad­vanced features of the Smart Remote Control. It will not explain how to use the functions for your devices. Please refer to your device’s user manual for information related to your device.
Unpacking the Smart Remote Con­trol
After you have unpacked the Smart Remote Control, check the contents to make sure the following items are included.
l Smart Remote Control l This user’s manual l SLC-2081 Connecter l Transmission cable
If any of the above items are missing or appear damaged, contact your dealer immediately. Do not throw the shipping carton away in case you need to ship your Smart Remote Control.
Page 9
Introducing the Smart Remote Control
Smart Remote Control features
This section provides an overview of the key features of the Smart Remote Control. For more information on getting the most from these features, refer to Chapter 2.
• Large touch screen display with automatic backlighting for visibility
in dim lighting
• Direct access buttons for accessing frequently used functions such as
volume, channel, play, mute, and stop
• Macro button stores 12 macros—each macro can sto re 25 commands
• Controls up to 10 devices including LD/VCD, TV, Satellite, VCR and
CD
• Popup information screen provides you with time, date, and battery
charge information
• Uses the IR codes from your existing remote controls to quickly set
up devices
Page 10
The Smart Remote Control User’s Manual
Identifying components
Please refer to the following illustrations to identify the components of the Smart Remote Control. This section provides an overview of the Smart Re­mote Control’s features and controls. Refer to Chapter 4 for a detailed description on operating and getting the most from these features.
Figure 1-1: Front view
Page 11
Introducing the Smart Remote Control
1. Light Sensor
The Light Sensor detects the ambient light brightness or dimness and will turn on according to the setting.
2. LCD
The LCD display enables you to configure and operate your de­vices by touching the screen on the function you want. Touch the LCD panel to power on the Smart Remote Control. Refer to Chapter 2, The LCD for a description of the functions in this dis- play.
3. Off button
W hen the Smart Remote Control displays the main menu, press this button to turn the Smart Remote Control off. When a device menu is displayed, this button functions as a power-off button for the device.
4. Device power button
After you have configured your devices, press this button to power on the selected device.
5. Device direct access buttons
These buttons function differently according to the currently se­lected device. Use these buttons to change channels, raise and lower the volume, and play or stop tapes, CDs, VCDs, and other recorded media. For more information, please refer to page 13, Direct access buttons.
6. Menu button
Press the Menu button for three seconds to enter and exit the a d­vance setup function. Refer to Chapter 4 for details.
7. Enter/mute button
When the main menu is being accessed, press this button to con­firm your changes. If the main menu is not being a ccessed, press this button to mute the audio output of your device.
8. Beep alert speaker opening
Enables you to hear a beep when you press a button. You can dis­able the beep from the information screen. Refer to page 12, The Information screen.
Page 12
The Smart Remote Control User’s Manual
1. IR port
The following illustration shows the rear of the Smart Remote Control.
2. Battery compartment
3. Learning eye
Figure 1-2: Rear view
1. IR port
Point the IR port at the IR receiver of the device you wish to ope r­ate.
2. Battery cover
Remove this cover to replace the AAA batteries.
3. Learning eye
Point your device’s remote control at this eye to enable the Smart Remote Control to learn your remote control’s functions. For more information, refer to page 23, Using the learning function.
Page 13
CChapter 2hapter 2
Getting Started
The previous chapter helped you to familiarize yourself with the various components and controls of the Smart Remote Control. This chapter will guide you through the steps for inserting the batteries and using the many fea­tures.
Incorrect use of the batteries may cause them to burst or may cause leakage, which might damage the interior of the unit. Be sure to only use the co r­rect type of rechargeable Ni-MH batteries with the Smart Remote Control.
Power supply
The Smart Remote Control operates on three AAA batteries. The batteries are packed separately and must be inserted before you can operate the Smart Remote Control.
Page 14
The Smart Remote Control User’s Manual
Inserting the batteries
To insert the batteries, refer to the following illustration and instructions:
1. Remove battery cover.
2. Insert batteries.
Ensure that you insert the batteries according to the marking inside the battery case.
Figure 2-1: Inserting the batteries
1. Locate the battery bay cover at the back of the Smart Remote Con­trol.
2. Put your thumb in the battery cover slot and pull to remove the cover.
3. Insert the batteries into the bay in the direction indicated in the bat­tery compartment.
4. Replace the battery bay cover. You will hear it click into place.
Page 15
Getting Started
Power supply precautions
• Be sure that the positive (+) and negative (-) polarities of each bat­tery match the polarities indicated in the compartment.
• Do not expose the batteries to excessive heat or flame.
• Keep the batteries out of the reach of children.
Power supply tips
• When the batteries are weak, it will be harder to control devices from a distance.
• Recharge the batteries immediately when the battery low power­warning icon appears in the information screen.
• The Ni-MH batteries have to be charged for 10 hours before the first use
• If you choose to use the rechargeable Ni-MH batteries, please replace your batteries in time when they have been used for over two years or have been recharged over 500 times; there might be a danger of leakage.
• Device configuration data will be automatically saved when batteries are being replaced.
Battery low icon
When the battery charge is low, the battery low icon will be displayed in the information screen. You should recharge the batteries or replace the bat­teries with new ones immediately.
Page 16
The Smart Remote Control User’s Manual
The LCD
The LCD (liquid crystal display) touch screen enables you to configure and operate your Smart Remote Control with the touch of a finger.
Turning the Smart Remote Control on
To turn the Smart Remote Control on, simply press the Hardware Access Button with your finger:
Figure 2-2: Turning the LCD on
Page 17
Getting Started
You can also turn the Smart Remote Control on by pressing one of the direct access buttons.
Touch screen precautions
Please read the following instructions carefully:
• Tap the LCD touch screen gently; never use force.
• Do not use a pen or any sharp object to tap the screen. Otherwise,
you might damage the surface. You can use a blunt object such as a pencil eraser or the cap of a pen.
• Keep the touch screen dry. Wipe off any spills immediately. The Smart Remote Control is not waterproof; never immerse it in liquid.
• Do not expose the Smart Remote Control to extreme temperatures. Keep it away from heat sources.
• Avoid dropping the Smart Remote Control.
• Do not drop anything on the touch screen.
• Clean the LCD touch screen with a soft cloth. If needed, dampen the
cloth slightly before cleaning. Never use abrasives or cleaning solu­tions.
Page 18
The Smart Remote Control User’s Manual
Macro screen
Information screen
beep signal.
The Information screen
The Information screen is displayed when you press the Information screen shortcut icon on the Smart Remote Control:
shortcut icon
shortcut icon
Main 1999
Date and time
01- 01
03:23
Friday
Indicates battery charge level.
Figure 2-3: The Information Screen
If you want to view the Information Screen from any menu, press the Infor­mation icon at the top right. Press the Information icon again to exit the Information screen.
Press this icon to enable or disable the
The Information Screen shows the date, day, time, and the current battery charge level. You can also press the mute icon to mute the beep that you hear when you press buttons on the touch screen.
Page 19
Getting Started
Smart Remote Control buttons
The Smart Remote Control has two sets of buttons for your convenience— direct access buttons and touch screen buttons.
Direct access buttons
The direct access buttons provide you with easy access to often-used func­tions such as volume and channel control, fast forward and fast reverse, play and stop.
Figure 2-4: Direct access buttons
Page 20
The Smart Remote Control User’s Manual
Touch screen buttons
The touch screen buttons enable you to control your devices as you would with your remote control, set up macros, and configure your LCD panel the way you want.
Figure 2-5: Touch screen buttons
Using the touch screen is easy. Simply press the screen to activate a function. Press the arrow keys at the bottom of the touch screen to scroll between pages in the menu.
Page 21
Chapter 3Chapter 3
Operating the Smart Remote Control
This chapter will tell you how to set up the Smart Remote Control, how to automatically configure devices, and how to use the advanced features such as the macros.
Press the Hardware Access Button with your finger to turn the Smart Remote Control on. The first screen that you see is the main menu.
The main menu
The main menu displays a list of the devices currently available on the Smart Remote Control. You can delete, rename, and configure these devices using the learning function (see page 23, Using the learning function).
Main
LD/
VCD
AMP TV
Sat
DVDVCR
Page 1 Page 2
AUX
1
TUNER
/ TAPE
Figure 3-1: The main menu
Main
AUX
2
CD
Page 22
The Smart Remote Control User’s Manual
Device Header
Press the left or right arrows to scroll between the main menu pages.
The device menu
Each device has its own device menu that contains the buttons and controls peculiar to that device. Each device has four pages in the menu. You can scroll between the pages using the LCD left and right arrows.
From the main menu, press the TV button to display the TV device menu:
Press this header to return to the Main Menu.
TV
1 2 3 4 5 6 7 8 9
100 0
1
Indicates menu page number
Figure 3-2: The TV device menu
You can return to Main menu by pressing both the Device Header or menu button. You can easily configure the devices using the learning function. Refer to page 23, Using the learning function).
Page 23
Operating the Smart Remote Control
The setup menu
The setup menu enables you to configure your Smart Remote Control.
Press the menu button
menu
for three seconds. The setup menu a ppears:
Setup
Clock
Timer Program
Adjust Macro Duplicate Other
Figure 3-3: The setup menu
To scroll through the items on the setup menu, use the hardware channel up
CH+
and channel down
ter an item submenu. Press the menu screen.
CH-
buttons. Press the enter (mute)
menu
button to return to the previous
mute
button to e n-
Refer to Chapter 4 for information on using the items in the setup menu.
Page 24
Chapter 4Chapter 4
Customizing the Smart Remote Control
This chapter shows you how to customize your Smart Remote Control to make it fit your particular requirements, how to use the learning function to configure your devices, and how to set up the LCD panel to your specifica­tions.
Press the menu button items are available:
Clock Enables you to set the date and time. Timer Enables you to set a timer to run a device at a specified time. Program Enables you to transfer commands from your device’s remote
control to buttons on the Smart Remote Control. You can also clear the settings for buttons and devices from this screen. You can also run macro setup from here and create macros for specific devices.
Adjust Enables you to resize, relabel, or delete LCD butto ns. Macro Enables you to record, label, and delete macros. Duplicate Enables you to duplicate all data to another SRC-2010 Other Enables you to adjust the LCD contrast and backlight, and to
calibrate the LCD panel.
Each item is covered in detail below:
menu
for three seconds to open the setup menu. Seven
Page 25
Customizing the Smart Remote Control
Setting the clock
The clock menu enables you to set the Smart Remote Control date and time. In the setup menu, scroll to clock and press enter. You see the following
screen:
Clock
Blinking cursor
1
1999
01- 01
03:23
Friday
0 1 2 3 4 5 6 7 8 9
Figure 4-1: The clock menu
Change the number under the blinking cursor by pressing 0 to 9 on the LCD panel. After you enter a number, the cursor automatically moves to the next position. Press the right and left arrows on the LCD to move the cursor for­ward or backward.
When you have finished making your adjustments, press enter.
Page 26
The Smart Remote Control User’s Manual
Using the timer
The timer function enables you to set up devices to turn on at specified times. In the setup menu, scroll to timer and press enter. You see a list of timers:
Timer
Timer 01
Timer 02 Timer 03 Timer 04
Figure 4-2: Timer list
Use the channel up or channel down to scroll through the list. There are 12 timers available. Select one of the timers and press enter. You see the follow­ing screen:
Timer
View
Setup Relabel
Figure 4-3: The timer menu
Each item is covered below.
Page 27
Customizing the Smart Remote Control
Timer view
View enables you to look at previously stored timer se ttings.
Timer setup
Setup enables you to setup a device function to go off at a specified time. Scroll to setup and press enter. The following screen appears:
Timer
Press here to select which day or days you want the timer to run.
03:23
0
Daily
0 1 2 3 4 5 6 7 8 9
Press these numbers to enter the time you want the timer to run.
Figure 4-4: Setting up timer options
Enter the time and day or date that you want the timer to go off. When you have set the timer, press enter. The device menu appears. Open a device and then press the button of the function that you want to apply the timer set­tings to. For example, you can set your VCR to record a movie at a certain time, or you can set a m acro to run at a specified time.
Remarks: Selectable timer function Disable: disable current timer function/ Daily: Everyday/ Specific: Specified
date/ Sunday: every Sunday/ Monday: every Monday/ Tuesday: every Tues­day/ Wednesday: every Wednesday/ Thursday: every Thursday/Friday: every
Page 28
The Smart Remote Control User’s Manual
Friday/Saturday: Every Saturday/ Mon.~Fri.: Monday ~ Friday/ Mon.~Sat.: Monday ~ Satu rday
Relabeling timers
You can easily relabel the timer names. Follow these instructions:
1. From the timer menu (Figure 4-3) scroll to Relabel and press e n-
ter. The following screen a ppears:
Timer 1. . . . . . . . . . . . . . .
. . . . . . . . . . . . . . .. . . . . . .
AMBNCOD G
H
IUJ
P
S
T
Y
Z
2. Enter the alphanumeric characters from the LCD screen. Press P1
to access upper case letters, press P2 to access lower case letters, and press P3 to access numbers and special characters.
3. Press enter when you have made your changes.
V
E K Q
W
F L
R
X
Page 29
Customizing the Smart Remote Control
Using the program menu
The program menu enables you to set up devices, clear a configuration for a key, clear the configuration for a device, or clear the configuration for all de­vices.
Program
Learning
Clr. Key Clr. Device Clr. All
Figure 4-5: The program submenu
Using the learning function
This section will cover the Smart Remote Control learning function, which en­ables you to set up the controls for each device with your device’s remote control.
When using the learning function, point your device’s remote control at the Smart Remote Control’s Learning eye as shown in the following illustration:
Page 30
The Smart Remote Control User’s Manual
Figure 4-6: Using the Learning eye
From the program menu (Figure 4-5), scroll to learning and press e nter. You see the device buttons:
Page 31
Customizing the Smart Remote Control
Press this macro shortcut icon to
tion.
This Macro button is designed for device menu. If you don’t need to
Macro function in device
In addition, from main menu’s MACRO 1 to MACRO 12, each
Program
open the macro recording func Refer to page 39.
AUX
2
set any
AUX
1
menu, Please skip this function.
TUNER
/ TAPE
CD
MACRO button is independent.
Figure 4-7: Programming devices
Press the button of the device that you want to program. You see the follow­ing screen:
Learn
Figure 4-8: Programming the direct access buttons
The buttons on the LCD correspond to the direct access buttons.
Page 32
The Smart Remote Control User’s Manual
The filled button corresponds to the direct access power button. With the Learning eye, you can now map buttons on your device remote control to the direct access buttons on the Smart Remote Control. Follow these instruc­tions:
1. Point your remote control at the Smart Remote Control’s Learning
eye as shown in Figure 4-6.
2. Press your remote control power button. When the screen dis-
plays OK, release the power button. Refer to the following illustration:
OK
3. The filled circle now corresponds to the channel up/play
rect access button.
4. Follow the preceding instructions to map the remaining buttons.
You can also press a direct access button directly, and then map a r emote con­trol function to the button.
After you have finished configuring the direct access buttons, press the right arrow button on the LCD screen to move to the next page in the device menu. Follow the instructions above to map each button on your remote control to the corresponding button on the Smart Remote Control’s LCD screen.
CH+
di-
Clearing a key
Page 33
Customizing the Smart Remote Control
The clear key function enables you to erase the settings for a button in one of the device menus. Follow these instructions:
1. In the program menu, scroll to Clr. Key and press enter. The list
of devices appears.
2. Press the device you want to configure.
3. In the device menu, press the key you want to clear.
4. Repeat steps 1 through 3 for all other keys you want to clear.
Clearing a device
The clear device function enables you to erase the commands for a device. Follow these instructions:
1. In the program menu, scroll to Clr. Device and press enter. The
list of devices appears.
2. Press the device you want to delete commands for. You see the
following screen:
Program
Sure ?
(Y) Enter
(N) Menu
3. Press enter to delete the commands for the device. Press menu to
cancel the deletion and return to the previous screen.
Clearing all devices
Page 34
The Smart Remote Control User’s Manual
The Clear All function enables you to erase the commands for all devices. Follow these instructions:
1. In the program menu, scroll to Clear All and press e nter.
2. You are prompted to press the enter button to delete the se ttings
for all devices, or press the menu button to cancel the changes and return to the previous screen.
Changing the LCD layout
The adjust menu enables you to resize, relabel, and delete buttons on the main menu and on the device menus.
In the setup menu, scroll to adjust and press enter. You see the following screen:
Adjust
Main Menu
Device
Figure 4-9: The adjust menu
Select Main Menu and press enter. You see the following screen:
Page 35
Customizing the Smart Remote Control
Adjust
Resize/Add
Relabel
Delete
Figure 4-10: Adjusting main menu buttons
Each item is described below.
Resizing or adding buttons on the main menu
Follow the instructions below to resize buttons on the main menu.
1. Scroll to Resize/Add and press enter. You see the main menu:
Press this icon
to toggle between Press this icon to undo an action.
button resize and
text edit functions.
Main
AUX
1
TUNER
/ TAPE
2. Press the button you want to resize.
AUX
2
CD
Page 36
The Smart Remote Control User’s Manual
Main
AUX
1
TUNER
/ TAPE
AUX
2
CD
3. Press the place where you want the upper left corner of the but-
ton to be. A black square appears where you pressed the LCD.
Main
AUX
1
TUNER
/ TAPE
AUX
2
CD
4. Press the place where you want the lower right corner of the
button to be. A black square appears where you pressed the LCD.
Page 37
Customizing the Smart Remote Control
Main
AUX
1
TUNER
/ TAPE
AUX
2
CD
5. Press the space between the two black squares:
Main
AUX
1
TUNER
/ TAPE
AUX
2
CD
6. The button is resized:
Page 38
The Smart Remote Control User’s Manual
Main
AUX
1
AUX
2
TUNER
/ TAPE
CD
Note the following points when resizi ng buttons:
• You cannot place the lower left corner above or to the left of the upper right corner.
• You cannot resize a button to where it will overlap an adjacent button.
• If you want to relabel a button, press the resize icon in the upper right corner. The icon changes to a text icon T . Press any of the device buttons, and relabel the button according to the instructions in the next sec­tion.
• If the total number of buttons on both main menu pages is less than ten, you can add a new device bu t­ton using the procedure for resizing buttons. The only difference is that you must select an empty space to place the left-hand corner and the right -hand corner.
Page 39
Customizing the Smart Remote Control
Relabeling buttons on the main menu
You can easily relabel the buttons on the main menu. Follow these instruc­tions:
1. From the adjust menu (Figure 4-9) select Main Menu and press
enter.
2. Scroll to Relabel and press enter again. You see the device list.
3. Select a device to relabel. You see the following screen:
TV . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . .
AMBNCODPFRE G
H
IUJVLXK
Q
S
T
Y
Z
W
4. Enter the alphanumeric characters from the LCD screen. Press P1
to access upper case letters, press P2 to access lower case letters, and press P3 to access numbers and special characters.
5. Press enter when you have made your changes. You see the fol-
lowing screen:
Page 40
The Smart Remote Control User’s Manual
Adjust
LD/VCD
SAT VCR DVD AMP TV TUNER TAPE CD
6. Select which device attributes you want applied to your button.
When accessing your relabeled button, the menus will be the same as the device that you select here.
Page 41
Customizing the Smart Remote Control
Deleting buttons on the main menu
You can easily delete buttons on the main menu. Follow these instructions:
1. From the adjust menu (Figure 4-9) select Main Menu and press
enter.
2. Scroll to Delete and press enter again. You see the device list.
3. Select a device button to delete. You see the following screen:
Adjust
Sure ? (Y) Enter (N) Menu
4. Press the enter button if you want to delete settings for the but-
ton. Press the menu button if you want to cancel the deletion and return to the previous screen.
Page 42
The Smart Remote Control User’s Manual
Adjusting buttons on the device menu
From the adjust menu (Figure 4-9) select Device and press enter. You see the following screen:
Adjust
Resize / Add
Relabel
Delete
Recall
Figure 4-11: Adjusting buttons on the device menu
The procedures for resizing and deleting buttons on the device menu are the same as those for resizing and deleting buttons on the main menu. However, the relabeling procedures are slightly different; there is an option to replace the button’s text with an icon. Additionally, there is one more option in the ad­just device submenu—Recall.
Page 43
Customizing the Smart Remote Control
Relabeling device menu buttons
You can easily relabel the buttons in device menus or choose icons to repre­sent the buttons. Follow these instructions:
1. From the adjust menu (Figure 4-9) select Device and press e nter.
2. Scroll to Relabel and press enter again. You see the device list.
3. Select a device to relabel, for example “CD”. You see the following
screen:
Adjust
T
Scan Shuf.
Edit
Rept.
Time
1
Press the T icon to toggle between edit
button text and resize modes.
4. Press the button that you want to relabel, for example Scan. You
see the following screen:
Page 44
The Smart Remote Control User’s Manual
Scan . . . . . . . . . . . . . . . . .
S
AMBNCODPFRE G
H
IUJVLXK
Q
S
T
Y
Z
5. Note that there is one additional button—the Icon button. Press
this button to display a list of icons:
Scan . . . . . . . . . . . . . . . . .
S
CH+ REC
W
icon
CH-
< >
icon
6. Press any of the buttons shown to replace the text “Scan” with an
icon. Press < or > to scroll between the pages and display more icons.
Using recall
The recall option enables you to recall the button’s original settings. After you press recall, the device list appears. Press the device that you want to re­set.
Page 45
Customizing the Smart Remote Control
Using macros
The macro feature enables you to store up to 20 commands for each macro. You can setup, relabel, and delete macros from the macro submenu. When you have created a macro, you will be able to run many commands by pushing only one button.
From the setup menu, scroll to macro and press enter. You see a list of mac­ros:
Macro
Macro 01
Macro 02 Macro 03 Macro 04
Figure 4-12: The macro list
Scroll to one of the macros in the list and press enter. You see the following screen:
Macro
Setup
Relabel Delete
Figure 4-13: The macro menu
Each item is described below.
Page 46
The Smart Remote Control User’s Manual
Macro setup
Follow these instructions to set up a macro:
1. From the macro menu, scroll to setup and press enter. The macro
is now being recorded.
2. Press the device button combination that you want to be recorded
into the macro. If necessary, you can set a time delay between each com mand in
the macro. In the upper right-hand corner of the screen, you see an hourglass icon 6. After pressing a com mand, press the hourglass icon to open the following screen:
Macro
0.5 Sec
2 Sec
5 Sec
10 Sec
1 Sec
3 Sec
7 Sec
15 Sec
Press one of the listed durations (0.5 seconds to 15 seconds) if you want to have a time delay occur between device commands.
3. When you have finished recording the macro press enter. You see
the following screen:
Page 47
Customizing the Smart Remote Control
Macro
Processing
4. The macro has been recorded.
To run the macro, press the macro shortcut icon M in the upper left -hand corner of the screen, and then select the macro you want to run from the macro list.
Relabeling a macro
Follow these instructions to relabel a macro:
1. In the setup menu, scroll to Macro and press enter. The list of
macros appears.
2. Scroll to the macro you want to rename and press enter. The
macro menu appears:
Macro
Setup
Relabel Delete
3. Scroll to Relabel and press enter. You see the following screen:
Page 48
The Smart Remote Control User’s Manual
Macro . 1. . . . . . . . . . . . .
M
. . . . . . . .
AMBNCOD G
H
IUJ
P
S
T
Y
Z
P1 P2 P3
4. Enter the alphanumeric characters from the LCD screen. Press P1
to access upper case letters, press P2 to access lower case letters, and press P3 to access numbers and special characters.
5. Press enter when you have made your changes.
V
E K Q
W
F L
R
X
Deleting a macro
Follow these instructions to delete a macro:
1. In the setup menu, scroll to Macro and press enter. The list of
macros appears.
2. Scroll to the macro you want to delete and press enter. The macro
menu appears:
Page 49
Customizing the Smart Remote Control
Macro
Setup
Relabel Delete
3. Scroll to Delete and press enter. You will see the following screen:
Macro
Processing
4. The macro information has been deleted.
The macro delete function only deletes the macro-recorded data; it does not remove the macro name from the macro list.
The duplicate menu
Please refer to the “SLC-2081 Connecter User’s guide”.
Page 50
The Smart Remote Control User’s Manual
Making LCD adjustments
The other menu enables you to set the LCD contrast, adjust the backlight, and calibrate your Smart Remote Control.
From the setup menu, scroll to Other and press enter. You see the following screen:
Other
Contrast
Backlight Calibrate
Figure 4-14: The “other” menu
Each item is described below.
Page 51
Customizing the Smart Remote Control
Adjusting the LCD contrast
Scroll to Contrast and press enter. You see the following screen:
Other
( )
Press this arrow to decrease the LCD contrast.
Contrast
Press this arrow to increase the LCD contrast.
Figure 4-15: Adjusting the contrast
Press the right LCD arrow to increase the contrast. Press the left LCD arrow to decrease the contrast.
Page 52
The Smart Remote Control User’s Manual
Press to
on.
Adjusting the LCD backlight
From the “other” menu, scroll to Backlight and press enter. You see the fol­lowing screen:
turn the backlight off and on.
Press to increase the backlight sensitivity level.
Press to decrease
<
the backlight sensitivity level.
Press to increase the duration that
the backlight stays on.
Indicates the current backlight sensitivity level.
Press to decrease the duration that the backlight stays
Back-Light
- - Switch - -
ON
- - Level - - -
Max : 99 Set : 52 Min : 00
+ _
- - Period - -
05
<
sec
Figure 4-16: Adjusting the backlight
The backlight detects the ambient light brightness or dimness and will turn on according to the setting in this screen.
Press and hold the Hardware Access Power button to automatically adjust the sensitivity level of the LCD panel to the ambient light. Alternatively you can press the + and – buttons to manually set the backlight sensitivity.
• Press + to increase the sensitivity of the backlight to the ambient
lighti ng. A high number indicates that a greater decrease of the brightness in the ambient lighting will automatically switch the backlight on.
• Press – to decrease the sensitivity of the backlight to the ambient
lighting. A low number indicates that a slight decrease of the brightness in the ambient lighting will automatically switch the backlight on.
When you have finished adjusting the backlight, press enter to save your changes and return to the other menu.
Page 53
Customizing the Smart Remote Control
Calibrating the LCD
Sometimes the LCD buttons becom e uncalibrated. When this happens, press­ing an LCD button will result in the adjacent button being pressed. In this instance, you should calibrate the LCD panel.
From the other menu, scroll to Calibrate and press enter. You will see the calibrate screen. Press the edge of the screen next to the pen icon. The pen icon will move to the next edge. Continue pressing the edge of the screen next to the pen icon until all four edges of the screen have been processed.
This concludes Chapter 4. The following appendixes provide specifications and some troubleshooting information.
Page 54
Specifications
Appendix AAppendix A
Model Battery
Dimensions Weight Power sa ving Battery consumption
Display Remote capability Display types
IR Range Acceptable frequency Memory Backlight Attachments Accessories
SRC-2010 3 x AAA alkaline batteries or Ni-MH re-
chargeable batteries 210 (L) x 68 (W) x 24 (H) mm
175.5g (batteries included) LCD turns off 25 minutes after last operation In use: 50mA / Standby: 280µA
LCD off: 30µA Touch liquid crystal display
Ten devices TV, DSS/SAT/cable, VCR, DVD, AMP,
tape/tuner, CD, AUX 8~ 10 M, 35~45
10 KHz~125 KHz Flash memory EL backlight User’s manual SLC-2081 Connecter,
Transmission cable
Page 55
Customizing the Smart Remote Control
Page 56
Appendix BAppendix B
Troubleshooting
If you have trouble configuring or operating the SRC-2010, first check that you have inserted the batteries correctly (page 8). Then check the items below.
Symptom Remedy
The SRC-2010 doesn’t operate your device.
You cannot operate a device even after con­figuring the device using the learning function (page 23).
You see an “error” display during the learning procedure.
You see an “error” display during opera­tion.
The LCD screen turns off.
• Move closer to the device. The maximum operating distance is approximately 10 me­ters.
• Ensure that you are aiming the SRC-2010 directly at the device and that there are no obstructions between the SRC-2010 and the device.
• Ensure that you have used the learning function (page 23) to configure the device.
• Make sure that the desired device on the SRC-2010 LCD panel has been selected.
• Make sure that you have correctly “mapped” your device’s remote control to the SRC-
2010.
• Clear the device data from the SRC-2010 (page 26) and carry out the learning func­tion again (page 23).
• Try the learning procedure again (page 23).
• The button that you pressed has not been
• The SRC-2010 is preset at the factory to
configured. Configure the button using the learning procedure (page 23).
automatically switch the LCD off after 25 minutes if left unused. Just press the
Hardware Access Button to turn the SRC-2010 back on again.
Loading...
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use