Page 1
INSTRUCTIONS FOR FITTING DIGITAL INPUT CARDS ID20
AND ID30 TO A MERIDIAN 861
INTRODUCTION
Digital input cards ID20 and ID30 each allow the connection of four more digital
inputs to an 861.
ID20 provides two additional ‘Toslink’ optical inputs and two SPDIF cable inputs.
ID30 provides three AES/EBU inputs and one ST fibre optic input designed to operate
with 50/125um, 62.5/125um and 100/140um cables.
This sheet is intended as an installation guide for the fitting ID20 and ID30 to a
Meridian 861.
WARNINGS
1. The power cord must be disconnected when any casing is removed.
2. Static sensitive parts are revealed when fitting this module.
TOOLS REQUIRED
No. 0 pozidrive screwdriver
3/16 inch flat blade screwdriver
SOFTWARE
This card requires 861 software version 1.40 or higher in order to operate. Before
beginning the installation of the new hardware check the 861’s software version is
equal to or higher than the version number supplied with the module. This number is
clearly marked on the 3.5inch floppy discs label.
The 861’s software version number can be found by holding down the display key the
front panel whilst the unit is in standby. The unit will display Meridian 861 x.xx were
x.xx is the version number.
If the software requires upgrading, proceed with this first, following the instructions
found in the Meridian 861 supplement.
JUMPER SETTINGS
Up to 8 of each of these cards can be fitted to an 861. Different cards of the same type
are differentiated by fitting the jumpers supplied on the cards as shown in the diagram
below. If you have only one of these cards, the card is number 0, and no jumpers need
to be fitted.
This card number corresponds to the ‘Card Number’ for the audio input in the
Sources section of the setup program. See ‘Setting up Sources’ below.
Page 2
0
1
2
3
4
5
6
7
SITING
Looking at the back of the 861.
IA20 and IA30 can be fitted in any free slots which can accommodate them. We
recommend that the right most free slot/s are used (See the diagrams below).
J2 J21 J22
J1
J3 J4 J5 J6 J7 J8 J9 J10 J11
J12
J13 J14
J15
J16
J17
J20 J23 J24
J18 J19
+
J2 J21 J22
J1
J3 J4 J5 J6 J7 J8 J9 J10 J11
+
AB00 Z300
J12
J13 J14
AB00 Z300
J15
J16
J17
J20 J23 J24
J18 J19
INSTALLATION PROCEDURE
Note: Observe static precautions throughout the installation period.
The following installation procedure applies for either card type.
Page 3
1. Switch of the unit and remove the power card.
2. Remove the blanking panel using a No. 0 pozidrive screwdriver. Retain panel and
fixings.
3. Slide new cards into the card guides adjacent to the rightmost panel. Ensure correct
card orientation (component side leftmost when viewed from the rear).
4. Check the card is aligned correctly and slides freely down the card guides.
5. Push the card gently until the rear panel is flush to the case. If the card is aligned
correctly in the card guides then only slight force will be required to mate the
connectors.
6. Gently tighten the rear fixings using the flat blade screwdriver. Do not over
tighten.
7. Connect the new inputs as required.
8. Re-connect the power cord and switch on.
SETTING UP SOURCES
The new inputs can be selected by setting up a Source for them in the Meridian Setup
program. When the program is running, go to 861 Surround Controller, Current
Settings, then Sources. Click on the source you wish to connect to this card. Select its
Audio tab, then by Card Type select ID20 or ID30. Then set the Card Number to
match the jumper options set on the card (number 0 if there is only one card fitted).
Then Select the Input on Card required and the input Precision.
Loading...