Page 1
DSW.2
User Guide
Page 2
2 EN
EN
DSW.2 User Guide
Important safety instructions
•
Read these instructions.
•
Keep these instructions.
•
Heed all warnings.
•
Follow all instructions.
•
Do not use this apparatus near water.
•
Clean only with a dry cloth.
•
Do not block any ventilation openings. Install in accordance with the
manufacturer’s instructions.
•
Do not install near any heat sources such as radiators, heat registers,
stoves, or other apparatus (including amplifiers) that produce heat.
•
Do not defeat the safety purpose of the polarized or grounding-type
plug. A polarized plug has two blades with one wider than the other.
A grounding type plug has two blades and a third grounding prong.
The wide blade or the third prong are provided for your safety. If the
provided plug does not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
•
Protect the power cord from being walked on or pinched particularly
at plugs, convenience receptacles, and the point where they exit
from the apparatus.
•
Only use attachments/accessories specified by the manufacturer.
•
Unplug this apparatus during lightning storms or when unused for
long periods of time.
•
Refer all servicing to qualified service personnel. Servicing is required
when the apparatus has been damaged in any way, such as powersupply cord or plug is damaged, liquid has been spilled or objects have
fallen into the apparatus, the apparatus has been exposed to rain or
moisture, does not operate normally, or has been dropped.
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,
DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE.
This apparatus has been designed with Class 1 construction and
must be connected to a mains socket outlet with a protective earthing
connection (the third grounding pin).
This apparatus does not include a power switch. The apparatus may be
isolated from mains power either by unplugging the power connector from
the rear of the unit, or by unplugging the connector at the opposing end
of the power cord or cable from its supply outlet. As a result, either or
both of these connectors should remain accessible
Safety warnings
Do not expose the unit to dripping or splashing.
•
Do not place any object filled with liquid, such as a vase, on the unit.
•
Do not place naked flame sources, such as lighted candles, on
•
the unit.
o avoid overheating leave at least 10cm around the equipment to
T
•
ensure sufficient ventilation.
Do not position the unit in direct sunlight, near heat sources such as
•
a radiator, or directly on top of heat producing equipment, such as a
power amplifier.
To avoid interference do not position the unit near strong electrical or
•
magnetic radiation, such as near a power amplifier.
Radio interference
FCC Warning: This equipment generates and can radiate radio
frequency energy and if not installed and used correctly in accordance
with our instructions may cause interference to radio communications
or radio and television reception. It has been type-tested and complies
with the limits set out in Subpart J, Part 15 of FCC rules for a Class
B computing device. These limits are intended to provide reasonable
protection against such interference in home installations.
EEC: This product has been designed and type-tested to comply
with the limits set out in EN55013 and EN55020.
Copyright
Meridian Audio Ltd
Latham Road
Huntingdon
Cambridgeshire
PE29 6YE
England
Copyright © 2011 Meridian Audio Ltd.
Visit us on the Web:
http://www.meridian-audio.com
Part no: P88477
This guide was produced by: Human-Computer Interface Ltd,
http://www.interface.co.uk/
Page 3
EN
Digital Channel
Selector
Power Inlet
2
1+2
1
Input
Output
SpeakerLink
Channel
selector
SpeakerLink
input
output
Power Fuse
Unpacking
DSW.2 User Guide
3
The DSW.2 is
Power cord.
•
Three rubber inserts.
•
This manual.
•
supplied with the following accessories:
Connections
The following diagram gives details of the connections on
the back of the subwoofer:
If any of these items are missing please contact your dealer.
NOTE: You should retain the packaging in case you need to
transport the unit.
Digital connections
Use this connection To connect to this
SpeakerLink input
SpeakerLink output
The SpeakerLink output of a Meridian
Digital Surround Controller or Audio
Core 200, or the SpeakerLink output of
another DSP loudspeaker.
The SpeakerLink input of a second
DSW.2 digital subwoofer, when daisy-
chaining the speakers.
Miscellaneous
Switch Description
Digital Channel Selector Set to 2 to use as an LFE/mono sub-
wo
ofer with a Digital Surround Controller.
Set to 1+2 to use with an Audio Core
200. Set the left subwoofer to 1 and
right subwoofer to 2 to use two sub-
the
woofers with a Digital Surround Controller.
Standby indicator
The status of the DSW.2 is shown by a green standby
indicator on the back
Status Description
Dimly illuminated Speaker in standby
Brightly illuminated Speaker operating
panel.
The subwoofer is switched on or into standby as appropriate
via the SpeakerLink connection by the Meridian system it is
connected to.
Fitting the rubber inserts
As supplied, the feet are suitable for soft, carpeted surfaces.
To use the DSW.2 on a hard surface insert one of the
supplied
foot:
self-adhesive rubber inserts into the recess on each
Page 4
4 EN
EN
Meridian Audio Core 200
MERIDIAN
SPEAKERLINK
INPUT OUTPUT
DSP3200 – Master
DSP3200 – Slave
MERIDIAN
SPEAKERLINK
INPUT OUTPUT
SpeakerLink lead
MERIDIAN
SPEAKERLINK
INPUT OUTPUT
SPEAKERLINK
IN OUT
SpeakerLink lead
SpeakerLink
lead
DSW.2 User Guide
Applications
Connect the upper SpeakerLink output on the Audio Core
To connect a pair of DSP3200s and a DSW.2 to a Meridian Audio Core 200
The DSW.2 is ideal in combination with a pair of DSP3200 or
DSP3300 loudspeakers to create a compact Audio Core 200
based system.
Connect the lower SpeakerLink output on the Audio Core
•
200 to the SpeakerLink input of the Master DSP3200, using
a Meridian SpeakerLink lead.
•
200 to the SpeakerLink input of the DSW.2 subwoofer,
using a Meridian SpeakerLink lead.
•
Connect the SpeakerLink output from the DSW.2 subwoofer
to the Slave DSP3200, using a Meridian SpeakerLink lead.
•
Set the Channel selector to the L/C position on the left
speaker, to the R position on the right speaker, and to the
1+2 position on the DSW.2 subwoofer.
DSW.2
– Subwoofer
Page 5
EN
Meridian Surround Controller
DSP3300 – Centre
MERIDIAN
SPEAKERLINK
INPUT OUTPUT
MERIDIAN
SPEAKERLINK
INPUT OUTPUT
MERIDIAN
SPEAKERLINK
INPUT OUTPUT
SpeakerLink
MERIDIAN
SPEAKERLINK
INPUT OUTPUT
SpeakerLink SpeakerLinkSpeakerLink
MERIDIAN
SPEAKERLINK
INPUT OUTPUT
DSP3200 – Rear L
DSP3200 – Front L (Master)
DSP3200 – Rear R
MERIDIAN
SPEAKERLINK
INPUT OUTPUT
DSP3200 – Front R
SpeakerLink
SpeakerLink
MERIDIAN
SPEAKERLINK
To use a DSW.2 as the subwoofer in a Meridian Digital Theatre
The DSW.2 is ideal as the subwoofer in a Meridian Digital
Theatre, in combination with DSP3200 or DSP3300 front and
rear loudspeakers and a DSP3300 centre speaker. The system
can be controlled by a Meridian Digital Surround Controller such
as the G68. The following diagram shows how to connect the
speakers using “home run” wiring.
Connect the L+R SpeakerLink output on the lower row of
•
the G68 to the Master digital speaker (here the front left
speaker), using a Meridian SpeakerLink lead.
Connect the appropriate SpeakerLink outputs on the G68
•
to each of the remaining speakers and the subwoofer, using
Meridian SpeakerLink leads.
DSW.2 User Guide
Set the Channel selector on the front and rear left speakers
•
to the L/C position, and on the front and rear right speakers
to the R position.
Set the Channel selector on the centre speaker to the L/C
•
position, and on the DSW.2 subwoofer to the 2 position.
Alternatively you can connect the speakers using “daisy chain”
wiring: connect the front and rear L speakers to the G68,
and then link each pair of speakers together by connecting
the output from the L speaker to the input of the R speaker.
Likewise connect the centre speaker to the G68, and then
link the output from the centre speaker to the input of the
subwoofer.
Note that if the system includes DSP loudspeakers with
displays, such as the DSP5200, one of them must be set up as
the master in the system.
5
DSW.2 – Subwoofer
Page 6
8 EN
DSW User Guide
Loading...