Meriam MGF16BN User Manual

MGF16BN Instructions

INSTALLATION AND PRECAUTIONS

Read these instructions before installing the gauge. The configuration options may be
easier to set up before the gauge is installed.

NEVER insert objects into the gauge port or blow out with compressed air. Permanent
damage will result to the sensor.

Use an appropriate screen or filter to keep debris out of gauge port.

Use fittings appropriate for the pressure range of the gauge.

Due to the hardness of 316L stainless steel, it is recommended that a thread sealant be
used to ensure leak-free operation.

Install or remove gauge using wrench on hex fitting only. Do not attempt to tighten by
turning housing or any other part of the gauge.

Do not apply vacuum to gauges not designed for vacuum operation. Permanent damage
will result to the sensor.

POWER-UP

1. Press the front button.

2. The full-scale range is indicated and the display segments are tested.

3. The actual pressure and units are displayed.

POWER-UP WITH ZERO

1. Be sure the gauge port is exposed to normal atmospheric pressure and no pressure or
vacuum is applied. The zeroing function is only activated at each power-up and the
stored zero correction is erased when the gauge is shut off.

2. Press and hold the front button until
This indicates that the gauge has been zeroed.

3. The full-scale range is indicated and the display segments are tested.

4. The actual pressure and units are displayed.

Attempting to zero the gauge with pressure greater than approximately 3% of full-scale
applied will result in an error condition, and the display will alternately indicate E r r0
and the actual pressure. The gauge must be powered down to reset the error condition.

NORMAL OPERATION

Following the start-up initialization, the display indicates the pressure reading updated
approximately 3 times per second. The auto shutoff timer starts when the gauge is pow­ered up or whenever the button is pushed, unless the gauge is set up with the auto shutoff
timer turned off (0 AST).

If excessive vacuum is applied to a pressure-only gauge, the display will indicate
– E r r until the vacuum is released. Applying vacuum to a gauge designed for pressure
may damage the pressure sensor. If excessive pressure is applied (112.5% over range), an
out-of-range indication of i – – – or i –.–.–.– will be displayed depending on model.

MINIMUM AND MAXIMUM READINGS

Minimum and maximum readings are continuously stored and updated whenever gauge
is on. The stored readings can be manually cleared if desired. The high and low memory
is also cleared whenever the gauge is off.

Press and hold the button for about 1 second until HI is displayed alternating with the
units. The maximum stored value is displayed.

After HI is displayed, press and hold the button again for about 1 second until LO is
displayed alternating with the units. The minimum stored value is displayed.

After LO is displayed, press and hold the button again for about 1 second until AP
(Applied Pressure) is displayed. The high and low readings are kept in memory and the
gauge returns to normal operation with the display indicating the current pressure.

Press and continue to hold the button until the display indicates Cir Hi/Lo (about 3
seconds total) and then release the button. Both HI and LO values are cleared and the
gauge returns to the normal mode and displays the current pressure.

SHUT-DOWN

To shut off the gauge manually at any time, press and hold the button until the display
indicates OFF (about 5 seconds) and then release.

When an auto shutoff time is set, the display indicates OFF five seconds prior to auto
shutoff. The button can be pressed to keep the gauge on. The auto shutoff timer is reset
whenever the button is pressed and released.

If the gauge is set up with the auto shutoff timer turned off (0 AST) it will stay on until
manually shut off or until the batteries are depleted. Turn gauge off when not in use to
conserve battery life.

DIMENSIONS

oooo

is displayed and then release the button.

OPERATION SUMMARY

Function Button Prompt—Release Button Result

Gauge On Press Gauge Range/Display Test Actual Pressure
Gauge On & Zero Press/hold
Hi Reading Press/hold HI Maximum Reading
Lo Reading Press/hold Lo Minimum Reading
Exit Hi/Lo Press/hold AP Actual Pressure
Clear Hi/Lo Press/hold HI / LO / AP + Cir Actual Pressure
Off, Clear Zero Press/hold HI / LO / AP + Ci

oooo

Zeroed Actual Pressure

r

+ OFF Gauge Off, Clear Zero

ENGINEERING UNIT SELECTION

Engineering unit selection is done via internal buttons to help prevent accidental or
unauthorized changes in the field. The selected engineering unit is stored in non-volatile
memory and will be retained even with the battery off or batteries removed. The avail­able engineering units depend on the sensor range, display resolution, and is limited to
prevent unwanted reading instability.

Compound (inHg/PSIG) gauges can be changed to display single-unit vacuum/pressure
readings (i.e. ±psig) when in the user configuration mode.

Standard PSIG units are mathematically converted to the newly selected engineering
unit. When the gauge is powered up, the originally configured PSIG range is displayed
and then the conversion with the selected engineering unit is displayed.

To change engineering units and remove the rear cover to gain access to the two internal
buttons located near the lower right and left corners of the circuit board.

With the gauge powered up, press and hold the UP button. Release the button when the
engineering units begin to flash.

Use the UP and DOWN buttons to scroll through the list of engineering units available
for the pressure range of the sensor.

When the desired units are displayed, press and release the front button to save the selec­tion and return to normal operation.

Replace the rear cover taking care not to pinch the power wires between the cover and
the case.

AUTO SHUTOFF TIME SELECTION

Auto shutoff time selection is done via internal buttons to help prevent accidental or
unauthorized changes in the field. The selected shut off time is stored in non-volatile
memory and will be retained even with the battery off or batteries removed.

Remove the rear cover to gain access to the two internal buttons located near the lower
right and left corners of the circuit board.

With the gauge powered up, press and hold the DOWN button. Release the button when
the auto shutoff time is displayed on the upper section.

The lower display segments will indicate AST M if the time displayed is in minutes,
and AST H if it in hours.

An auto shutoff time of zero signifies that the auto shutoff feature is disabled.

Use the UP and DOWN buttons to select 0, or 1, 2, 5, 10, 15, 20 or 30 minutes, or 1,
2, 4, or 8 hours.

When the desired auto shutoff time is displayed, press and release the front button to save
the selection and return to normal operation.

Replace the rear cover taking care not to pinch the power wires between the cover and
the case.

BATTERY REPLACEMENT

A low battery indication will be shown in the upper left-hand corner of the display when
the battery voltage falls sufficiently. The battery should be replaced soon after the indica­tor comes on or unreliable readings may result or the gauge may fail to power up.

1. Remove the 6 Phillips-head screws on the back of the unit.

2. Remove batteries by lifting up the positive end of the battery (opposite the spring)
taking care not to bend the battery holder spring.

3. Always replace both batteries at the same time with high quality alkaline batteries.
Install batteries with correct orientation. The negative (flat) end of each battery should
be inserted first facing the battery holder spring.

4. Replace the back cover, including the rubber sealing gasket taking care not to pinch
the power wires between the cover and the body of the case.

s

¼" NPT

XXXXX

i i i i i

8

8888

3.5"

3.0"

2

t

10920 Madison Ave

Cleveland, OH 44102

Phone: [phone]

0.75"

2.0"

Fax: [phone]

© 01-09Specifications are subject to change without notice.

MGF16BN Configuration and Calibration Instructions

USER CONFIGURATION

Remove the rear cover to gain access to the buttons located near the lower right and left
corners of the circuit board.

With the gauge off, press and hold the UP button. Then press the front button. Release
all buttons when the display indicates CFG and the program version then the full-scale
range is indicated and the display segments are tested.

The display then indicates _ _ _ _ with the first underscore blinking, and with PASS
on the character segments.

Note: The gauge will automatically revert to normal operation if no buttons are oper­ated for approximately 15 seconds. To cancel and return to normal operation, press and
release the front button without entering any pass code characters.

Enter the user-modifiable pass code (3510 factory default)

1. Use the UP or DOWN buttons to set the left-most digit to 3.

2. Press and release the front button to index to the next position. The 3 will remain,

and the second position will be blinking.

3. Use the UP or DOWN buttons to select 5.

4. Press and release the front button to index to the next position.35 will remain, and

the third position will be blinking.

5. Use the UP or DOWN buttons to select i.

6. Press and release the front button to index to the next position. 35i will remain, and

the fourth position will be blinking.

7. Use the UP or DOWN buttons to select 0.

8. Press and release the front button to proceed with configuration procedures.

If an incorrect pass code is entered, the gauge will return to the start of the pass code
entry sequence.

Factory/User configuration

The upper display section will be blank, and the lower section will display either
USER_ or FCTRY.

If USER_ is selected, the existing user configuration will be retained and will be acces­sible for modification as described in the following steps. To select USER_, press and
release the DOWN button. The lower section of the display will indicate USER_. Press
and release the front button to continue with configuration.

If FCTRY is selected, the existing user configuration will be replaced by the configura­tion as it left the factory. To select FCTRY, press and release the UP button. The lower
section of the display will indicate FCTRY. Press and release the front button to restore
the factory configuration and restart the gauge.

High and low value capture configuration

The upper display section will be blank.

Use the UP and DOWN buttons to select from the following:

HI/LO Both highest and lowest values measured will be captured
HI/-- Only highest value measured will be captured

--/LO Only lowest value measured will be captured

--/-- Capture feature is disabled

Press and release the front button to move on to the next parameter.

Gauge type configuration (vacuum/pressure models only)

This will only appear with 15, 100, or 200 psig ranges that were originally ordered as
compound gauges.

The upper display section will be blank.

Use the UP and DOWN buttons to select from the following:

-/+EU Vacuum is indicated as negative pressure in the selected engineering units
CMPND Vacuum is negative INHG, pressure is PSI

Press and release the front button to save the user configuration and restart the gauge.

Replace the rear cover taking care not to pinch the power wires between the cover and
the case.

CALIBRATION

The gauge is calibrated at the factory using equipment traceable to NIST. There is no
need to calibrate the gauge before putting it in service.

Calibration should only be performed by qualified individuals using appropriate calibra­tion standards and procedures. The calibration equipment should be at least four times
more accurate than the gauge being calibrated. The calibration system must be able to
generate and measure pressure/vacuum over the full range of the gauge. A vacuum pump
able to produce a vacuum of 10 microns (0.01 torr or 10 millitorr) or lower is required
for vacuum gauges.
Remove the rear cover to gain access to the UP and DOWN buttons located near the
lower right and left corners of the circuit board.

With the gauge off, press and hold the DOWN button. Then press the front button.
Release all buttons when the display indicates CAL.

The display begins by indicating the full-scale positive pressure rating of the gauge in
the engineering units as configured by the factory, and then proceeds to show all display
segments.

Before the gauge enters the Calibration Mode, the display initially indicates _ _ _ _ with
the first underscore blinking, and with PASS on the character segments.

Note: The gauge will automatically revert to normal operation if no buttons are oper-

ated for approximately 15 seconds. To cancel and return to normal operation, press and
release the front button without entering any pass code characters.

Enter the user-modifiable pass code (3510 factory default)

1. Use the UP or DOWN buttons to set the left-most digit to 3.

2. Press and release the front button to index to the next position. The 3 will remain,

and the second position will be blinking.

3. Use the UP or DOWN buttons to select 5.

4. Press and release the front button to index to the next position.35 will remain, and

the third position will be blinking.

5. Use the UP or DOWN buttons to select i.

6. Press and release the front button to index to the next position. 35i will remain, and

the fourth position will be blinking.

7. Use the UP or DOWN buttons to select 0.

8. Press and release the front button to proceed with configuration procedures.

If an incorrect pass code is entered, the gauge will return to the start of the pass code
entry sequence.

The gauge enters and remains in the Calibration Mode until restarted manually or power
is removed. While in the Calibration Mode, the auto shutoff timer is disabled, the push
button zeroing at startup is disabled, the Min/Max feature is disabled, and compound
range models are set for the same engineering units for pressure and for vacuum.

The calibration may be performed in any of the available engineering units as well as
percent (PCT). For greatest accuracy, use the UP and DOWN buttons to select engineer­ing units for calibration with highest resolution. Press and release the front button when
the appropriate engineering units are displayed. Suggested units are listed below.

Sensor Suggested range and units for calibration

5 PSI 5.000 PSI
15 PSI 775.7 MMHG (TORR)
30 PSI 61.08 INHG
50 PSI 50.00 PSI
60 PSI 60.00 PSI
100 PSI 7.031 KG/CM2
200 PSI 407.2 INHG
300 PSI 610.8 INHG
500 PSI 500.0 PSI
1000 PSI 70.31 KG/CM2
2000 PSI 4072 INHG
3000 PSI 6108 INHG
5000 PSI 5000 PSI
Any 10000 PCT (percent)

The display will then indicate the currently applied pressure in the engineering units
selected for calibration.

Gauge reference pressure gauges

Apply zero pressure. This may be done by venting to atmosphere. The character seg­ments of the display will alternate between ZERO and CAL. Adjust for a display
indication of zero using the UP and the DOWN buttons. *See note below.

Apply full-scale pressure. The character segments of the display will alternate between
+SPAN and CAL. Adjust for a display indication of full-scale pressure using the UP
and the DOWN buttons. *See note below.

Apply 50% full-scale pressure. The character segments of the display will alternate
between +MID and CAL. Adjust for a display indication equal to 50% of full-scale
pressure using the UP and the DOWN buttons. *See note below.

Compound gauges (vacuum/pressure ranges)

Warning: application of vacuum to non-vacuum models may result in irreparable dam­age to the sensor.

In addition to the steps described above for pressure gauges, apply full-scale vacuum.
The character segments of the display will alternate between -SPAN and CAL. Adjust
for a display indication of actual applied vacuum using the UP and the DOWN buttons.
*See note below.

For bipolar and –30.00inHg/+15.00psig compound range models only, apply 50% full­scale vacuum. The character segments of the display will alternate between -MID and
CAL. Adjust for a display indication equal to 50% of full-scale vacuum using the UP
and the DOWN buttons. *See note below.

* Note: Each time one of the calibration buttons is pressed and released quickly, a small
change is made to the digitized pressure signal. It may take more than one of these
small changes to result in a single digit change on the display. To make larger changes,
press and hold the appropriate calibration button. After about one second, the display
will begin to change continuously. Release the button to halt the continuous change.
Then make fine adjustments by pressing and quickly releasing the calibration buttons
as previously described.

Save Calibration

Once the adjustments are complete, press and hold the front button until the display
indicates ---- then release the button to store the calibration parameters in non-volatile
memory and restart the gauge.

Verify the pressure indications at 0%, 25%, 50%, 75% and 100% of full scale.

Replace the rear cover taking care not to pinch the power wires between the cover and
the case.

© 01-09

MGF16BN User Defined Pass Code Configuration

USER DEFINED PASS CODE CONFIGURATION

Remove the rear cover to gain access to the buttons located near the lower right and left
corners of the circuit board.

Battery powered models: With the gauge off, press and hold the UP button. Then press
the front button. Release all buttons when the display indicates CFG.

The display initially indicates _ _ _ _ with the first underscore blinking, and with PASS
on the character segments.

Note: The gauge will automatically revert to normal operation if no buttons are operated
for approximately 15 seconds.

To cancel and return to normal operation, press and release the POWER button without
entering any pass code characters.

Enter access code 1220

1. Use the UP and DOWN buttons to set the left-most digit to i.

2. Press and release the front button to index to the next position. The i will remain, and

the second position will be blinking.

3. Use the UP and DOWN buttons to select 2.

4. Press and release the front button to index to the next position. i2 will remain, and

the third position will be blinking.

5. Use the UP and DOWN buttons to select 2.

6. Press and release the front button to index to the next position. i 2 2 will remain, and

the fourth position will be blinking.

7. Use the UP and DOWN buttons to select 0.

8. Press and release the front button to proceed.

Note: If an incorrect access code was entered, the gauge will return to the start of the
access code entry sequence.

Change access code

Once the correct access code has been entered, the display will indicate the existing user­defined pass code with UDPCD on the character segments.

1. Operate the UP or DOWN button to select the first character of the new pass code.

2. When the correct first character is being displayed, press and release the front button
to proceed to the next pass code character.

3. Repeat above until the entire pass code is complete.

4. To exit the User-Defined Pass Code change mode, press and hold the front button.
Release the button when the display indicates ---- to restart the gauge.

5. Replace the rear cover taking care not to pinch the power wires between the cover
and the case.

10920 Madison Ave

Cleveland, OH 44102

Phone: [phone]

Fax: [phone]

© 01-09

MGF16BN Battery-Powered Digital Pressure Gauges

l ±0.25% Test Gauge Accuracy

l 316L Stainless Steel Wetted Parts

l NEMA 4X

l Capture Minimum and Maximum Readings

l Push Button Zero

l Selectable Engineering Units

l Selectable Auto Shutoff Times

The Meriam Instrument MGF16BN digital pressure gauge successfully addresses the
modern demands of process pressure measurement. Pressure ranges are available to
5,000 PSIG at standard accuracy of ±0.25% of full scale and optional accuracy of ±0.1%
of full scale. Compound gauges that can be used for positive pressure measurements and
vacuum measurements are also available.

The display is a 4½ digit LCD with 0.5" high numerals and a lower alphanumeric display
for engineering units and to aid in set up. Each gauge includes up to 15 field selectable
engineering units depending on the sensor range. The selectable units include PSIG,
kiloPascals, megaPascals, millibar, bar, atmospheres, kilograms per square centimeter,
grams per square centimeter, centimeters of water, ounces per square inch, feet of water,
inches of water, millimeters of mercury, Torr, and inches of mercury.

Other standard features include min/max capture, zeroing, pass code program lock-out,
adjustable display shutoff time and field recalibration. The housing is ABS/polycarbon­ate and is NEMA 4X rated. Wetted components are 316L stainless steel for compatibility

with many process fluids. Process connection is via a 1⁄4" MNPT 316L stainless steel

fitting. The gauge is powered by two AA alkaline batteries.

Typical applications are instrumentation and control in the process industries, hydraulics,
pneumatics, industrial gases and OEM’s.

ACCURACY

Standard: ±0.25% of full scale ±1 least significant digit
includes linearity, hysteresis, repeatability
Optional: -HA ±0.1% FS ±1 LSD

-NC NIST traceable test report and calibration data

DISPLAY

3 readings per second nominal display update rate
4½ digit LCD, 0.5" H, 5 character 0.25" H alphanumeric lower display

CONTROLS & FUNCTIONS

Front button turns gauge on or off, zeros gauge, and cycles through min/max functions
Internal push buttons for selection of engineering units, selection of auto shutoff times,
and calibration

CALIBRATION

Pass code protected calibration
Non-interactive zero, span, and linearity, ±10% of range

AUTOMATIC SHUTOFF

5 minute default
User selectable times ranging from 1 minute to 8 hours or front button on/off

POWER

2 AA alkaline batteries
Approximately 2000 hours battery life

WEIGHT

Gauge: 9 ounces (approximately)
Shipping weight: 1 pound (approximately)

MATERIAL

ABS/polycarbonate NEMA 4X case, rear gasket, polycarbonate label

CONNECTION SIZE

1/4" NPT male, 316L SS

MATERIAL, MEDIA COMPATIBILITY

All wetted parts are 316L SS, compatible with most liquids and gases

OVERPRESSURE

3000 psig range: 5000 psig
5000 psig range: 7500 psig
All others: 2 x pressure range

112.5% FS out-of-range display: i – – – or i –.–.–.– depending on model

BURST PRESSURE

4 times sensor pressure rating, or 10,000 psi, whichever is less

ENVIRONMENTAL

Storage temperature: –40 to 203°F (–40 to 95°C)
Operating temperature: –4 to 185°F (–20 to 85°C)
Compensated temperature: 32 to 158°F (0 to 70°C)

Low battery symbol on display when batteries must be replaced

RANGES ±0.25% FS MODELS ±0.1% FS MODELS SELECTABLE ENGINEERING UNITS

–30.0 inHg to 15.0 PSIG

–30.0 inHg to 100.0 PSIG

–30.0 inHg to 200.0 PSIG

0 - 5.000 PSIG

0 - 15.00 PSIG

0 - 60.00 PSIG

0 - 100.0 PSIG

0 - 200.0 PSIG

0 - 300.0 PSIG

0 - 500.0 PSIG

0 - 1000 PSIG

0 - 2000 PSIG

0 - 3000 PSIG

0 - 5000 PSIG

Optional for all Models

MGF16BN–30V15PSIG

MGF16BN–30V100PSIG

MGF16BN–30V200PSIG

MGF16BN5PSIG MGF16BN5PSIG-HA

MGF16BN15PSIG MGF16BN15PSIG-HA

MGF16BN60PSIG MGF16BN60PSIG-HA

MGF16BN100PSIG MGF16BN100PSIG-HA

MGF16BN200PSIG MGF16BN200PSIG-HA

MGF16BN300PSIG MGF16BN300PSIG-HA

MGF16BN500PSIG MGF16BN500PSIG-HA

MGF16BN1000PSIG MGF16BN1000PSIG-HA

MGF16BN2000PSIG MGF16BN2000PSIG-HA

MGF16BN3000PSIG MGF16BN3000PSIG-HA

MGF16BN5000PSIG MGF16BN5000PSIG-HA

NC NC

InHg/PSI, can be user reconfigured as a bipolar gauge with selectable units

InHg/PSI, can be user reconfigured as a bipolar gauge with selectable units

InHg/PSI, can be user reconfigured as a bipolar gauge with selectable units

PSIG, kPa, mbar, bar, atm, kg/cm

PSIG, kPa, MPa, mbar, bar, atm, kg/cm2, g/cm2, cmH2O, oz/in2, ftH2O, inH2O, mmHg, torr, inHg

PSIG, kPa, MPa, mbar, bar, atm, kg/cm2, g/cm2, cmH2O, oz/in2, ftH2O, inH2O, mmHg, torr, inHg

PSIG, kPa, MPa, mbar, bar, atm, kg/cm

PSIG, kPa, MPa, bar, atm, kg/cm2, oz/in2, ftH2O, inH2O, inHg

PSIG, kPa, MPa, bar, atm, kg/cm

PSIG, kPa, MPa, bar, atm, kg/cm2, ftH2O, inHg

PSIG, kPa, MPa, bar, atm, kg/cm

PSIG, MPa, bar, atm, kg/cm2, ftH2O, inHg

PSIG, MPa, bar, atm, kg/cm2, ftH2O, inHg

PSIG, MPa, bar, atm, kg/cm

2,

g/cm2, cmH2O, oz/in2, ftH2O, inH2O, mmHg, torr, mmH2O, inHg

2,

g/cm2, cmH2O, oz/in2, ftH2O, inH2O, mmHg, torr, inHg

2,

oz/in2, ftH2O, inHg

2,

ftH2O, inHg

2

NIST traceability certificate with 5 test points and data

© 01-09