Page 1
MFC 4100 HART® Communicator
MFC 4101 HART
MFC 4102 HART
MFC 4103 HART
INSTRUCTION MANUAL
File No. 4100:440-4
December 2003
Communicator with Documentation
Communicator with Intrinsic Safety (I.S.)
Communicator with Documentation and I.S.
OPERATOR
Page 2
MFC 4100 SERIES OPERATOR INSTRUCTION MANUAL
MFC 4100 HART® Communicator
MFC 4101 Communicator with Documenting capability
MFC 4102 Communicator with Intrinsically Safe (I.S.) rating
MFC 4102 Communicator with Documenting capability & I.S. rating
I
MPORTANT NOTICE
Important information on the product is contained in this
manual. Read this manual carefully and completely before
operating the product. For the safety of the operator and the
system, a thorough understanding of this manual is necessary
before commissioning, using or maintaining the product.
A
SSISTANCE
For customer assistance please contact the local Meriam Representative or Meriam Process Technologies
directly. For a geographic listing of Representatives and contact information, visit our web site at
www.meriam.com
directly by phone at (216) 281-1100 or by e-mail at meriam@meriam.com
to Technical Services.
®
HART
is a registered trademark of the HART Communication Foundation.
and click on the “Representatives” button. Contact Meriam Process Technologies
Meriam Process Technologies
10920 Madison Avenue
Cleveland, Ohio 44102
TELEPHONE: (216) 281-1100
FAX: (216) 281-0228
E-mail: meriam@meriam.com
Web Site: www.meriam.com
. Direct all assistance inquiries
Page 3
MFC 4100 HART Communicator
OPERATING INSTRUCTIONS
MFC 4100, MFC 4101, MFC 4102, MFT 4103
TABLE OF CONTENTS
Subject Page
MFC 4100 Communicator Overview ........................................................................................................ 1
Display Overview ...................................................................................................................................... 1
Header Line Symbols ........................................................................................................................... 2
Keypad Overview ...................................................................................................................................... 2
Alphanumeric Keys .............................................................................................................................. 3
Left / Right Arrow Keys ....................................................................................................................... 4
Soft Keys............................................................................................................................................... 4
Thumb Operated Keys .......................................................................................................................... 4
General Operation...................................................................................................................................... 5
Power Options....................................................................................................................................... 5
Navigating Menus................................................................................................................................. 5
Turning on MFC ................................................................................................................................... 6
MFC Main Display ............................................................................................................................... 6
MFC Configurations Settings ............................................................................................................... 7
Lockout Feature ............................................................................................................................... 7
Lockout Code.............................................................................................................................. 7
Disable Lockout .......................................................................................................................... 8
Changing Lockout Code ............................................................................................................. 8
Backlight (off timer) ................................................................................................................... 8
Off Timer .................................................................................................................................... 8
Clock Edit ................................................................................................................................... 8
Enter PC Comm. Mode............................................................................................................... 8
Battery Installation & Removal (all models) ............................................................................................. 9
External Connections ................................................................................................................................. 9
DB-9 Connection ....................................................................................................................................... 9
Hazardous Area Use ................................................................................................................................ 10
Intrinsically Safe Operation ................................................................................................................ 10
®
HART
HART Commands ................................................................................................................................11
HART Connections...............................................................................................................................11
HART Communications .......................................................................................................................12
Initial Screens / Online Mode ......................................................................................................12
Multi-drop Poll.............................................................................................................................13
Manual Device 0 Poll...................................................................................................................13
Offline Menu Mode .....................................................................................................................13
List / Show DOFs....................................................................................................................14
List / Edit Configurations........................................................................................................14
Create Configurations .............................................................................................................15
Delete All Configurations .......................................................................................................15
Delete Individual Configurations / Clearing Configuration Memory.....................................15
Online Setup Mode ......................................................................................................................15
Communications Trouble Shooting .............................................................................................15
More Status Message ...................................................................................................................16
Communications with MFC 4100...............................................................................................11
Page 4
Save / Send Configuration Functions...........................................................................................16
Documenting HART Configurations with Meriam DMS software..........................................................17
MFC 4100 Device Specific & Generic HART Communication ..............................................................17
Using Generic Communications ..........................................................................................................17
DOF / Firmware Download Site ...............................................................................................................18
Who may use.........................................................................................................................................18
PC Requirements ..................................................................................................................................18
Preparing the MFC for updating ...........................................................................................................18
Preparing to Download .........................................................................................................................18
Using the Download Site ......................................................................................................................19
Subscriber Options................................................................................................................................19
MFx Installer Utility .................................................................................................................................19
Returning the MFC for Repairs ................................................................................................................20
APPENDIX
MFC Specifications ..............................................................................................................................21
MFC Models, Options, Ordering Information ......................................................................................21
MFC Accessories List...........................................................................................................................22
Intrinsically Safe Control Document ....................................................................................................23
HART Command Structure Menu Trees ........................................................................................ 24-28
Page 5
p
l
MFC 4100 HART COMMUNICATOR
The MFC 4100 HART Communicator is the latest handheld communicator in the Meriam family of
HART devices. All HART field devices can be configured, polled, and trimmed using the MFC with
HART communications. The MFC is a full function HART Communicator supporting Universal,
Common Practice and Device Specific commands for commissioning, configuration and maintenance
operations.
Lanyard
ins (2x)
AC Adaptor
jack
Up, Select
Down thumb
keys
Hand
strap
Battery
door
Thumb
keys
Display
Soft keys
Feature keys
Alpha numeric
and edit keys
Top View
HART
connection
DB-9 Seria
connection
Side View
Front View
Bottom View
Note: For Intrinsically Safe MFC models, consult the
Hazardous Area Use
section of this manual for
specific details on use of approved MFCs and applicable restrictions.
DISPLAY OVERVIEW
The display of the MFC 4100 is a 128 x 128 pixel graphic display with backlight. Viewable area is 2.6” x
2.6” for 13 viewable message lines. The display provides three types of information: 1) header information
including display titles, HART communication status indicator, SHIFT indicator, alpha or numeric entry
mode indicator and battery gauge, 2) main data display section for display of MFC operating menus, HART
menus, and device information, and 3) footer information defining the display’s soft key functionality.
The following photo depicts the MFC Offline menu and Soft keys:
1
Page 6
y
HEADER LINE SYMBOLS KEY
heart symbol indicates active HART
communication
u up arrow indicates SHIFT key is on
# number sign indicates numeric / symbol
entry is the present entry mode for all dual
functions keys
A letter indicates alpha entry is the present
entry mode for all dual function keys
battery symbol indicates MFC under battery
power; filled portion indicates remaining
battery
electrical plug symbol indicates the AC
adapter is connecting and powering the MFC
BUSY
BUSY text box replaces either power symbol
when the microprocessor is busy executing a
previously requested task. Do not press keys
when this status s
mbol is displayed.
ON/OFF
KEY PAD OVERVIEW
The MFC keypad has three basic key types: single
function keys, dual-function keys, and soft keys
with changing definitions.
Single function keys control a dedicated MFC
function.
Dual-function keys, through the use of the Alpha
Lock or Shift keys, toggle between two separate
functions as needed to facilitate data entry.
Soft key functions change depending on the
present operating mode. Soft key definitions are
displayed at the bottom of the LCD, just above
their respective gray soft keys.
The left hand thumb keys can be used to scroll
up, scroll down, and to select menu items.
On/Off
Pressing the ON/OFF key powers up or turns off the MFC. As the unit powers up, an internal
diagnostic check is performed. Any abnormalities are posted on the display. The unit will briefly
display the MFC model number and then check for a HART device with address of zero. If a device
with zero address is found, the MFC immediately goes into online status and displays information
about the device. If no device is found, the MFC enters the MFC Main navigation screen. To turn the
2
Page 7
e
QUICK
MENU
Hom
QUICK
MENU
SHIFT
MFC off, press and hold the ON/OFF key for approximately .5 seconds. Unit will power down
provided a critical HART operation is not in process.
Quick Menu
The Quick Menu key initiates HART communications and then displays ten (10) HART menu
choices for the connected device. These menus are used to short cut the traditional HART menus to
enable the user to arrive quickly at the desired functions. Typical Quick Menu options include: Main
Menu, Config Menu, Rerange, Basic Info, Construction Materials, Display, Sensors, Signal
Conditioning, Self Test. Quick Menu is disabled while critical HART operations are in process.
Home
The key sequence
SHIFT, Home
connected device. The Home function is disabled while critical HART operations are in process.
returns the user to the initial or “home” HART menu for the
Document
This key provides rapid access to HART communication Save/Send Configs options, List/Edit
Configs, and Create Configs functions for all MFC models. For Documenting models MFC 4101
and MFC 4103, this key also provides documenting functions used with the Meriam Device
Management System software. Access to this key is disabled while critical HART communications
are in process.
Display Contrast
This key allows the user to adjust the contrast of the LCD display for ambient lighting and user
preferences at any time and in any operating mode. Pressing and holding this key cycles through all
available contrast settings. If the display is faded or blacked out, simply depress the key until the
display returns to an acceptable level. After adjusting Display Contrast, wait at least five (5) seconds
before turning unit off to insure storage of new contrast setting. Ambient temperature compensation
is included in the MFC 4100.
Back Light
This key provides a backlight to illuminate the display in poor light conditions. Battery life is
impacted by long-term use of the backlight feature. An automatic shut off timer is available to
the user under the Main Menu’s MFC soft key.
Alphanumeric / Symbol Entry
The alphanumeric keys have the heaviest population on the keyboard and are the method of entering
B
2
data into the MFC. Each MFC display has a default alpha or numeric / symbol entry mode based on
the most likely used mode for the display’s function. This reduces user workload to a minimum.
L
Pressing the ALPHA LOCK key activates the other entry mode at the user’s convenience. Pressing
the SHIFT key converts the next key stroke to the inactive entry mode and then automatically reverts
back to the default mode. The letter “A” in the display header line indicates the alpha input default
is active while a # sign in the display header indicates the numeric / symbol input is the default.
SHIFT
The SHIFT key is used to activate the secondary functions of the MFC’s dual-function keys for the
next keystroke only. When the SHIFT key is active, an up arrow
display to the left of the battery power (or AC wall plug) symbol. SHIFT is also used to activate the
Page Up and Page Down soft key functions while viewing lists of information (installed DOFs,
stored configs, etc…).
u
is displayed at the top of the
3
Page 8
Alpha Lock
ALPHA
LOCK
This key changes the keypads dual function keys from numeric/symbol entry mode to alpha
character entry mode and back. The present entry mode is indicated in the display header line next to
the power supply indicator on the upper right of the screen. The letter “A” in the display header line
indicates that alpha entry is active while a # sign in the display header indicates that numeric /
symbol entry is active.
Left / Right Arrow keys
These keys support cursor movement forward and backward for text / numeric editing needs. The
default edit mode is “overwrite.” For navigating functions, the left arrow emulates the
and the right arrow emulates the
Select
soft key.
Back
soft key
DEL
Delete
This editing key will delete the character located above the cursor in a text / numeric string.
Insert
INS
DEL
The Insert text edit function is activated by pressing the
the next alpha or numeric / symbol keystroke will be inserted into the open text field. The
“overwrite” default mode is restored upon completion of the insert operation.
The four gray keys located immediately below the display are Soft Keys. The specific functions of
these keys change depending on the operating mode of the MFC. Present definitions are displayed at
the bottom of the MFC display. The following are examples or Soft Key definitions and their uses:
– moves indicator arrow up one line in a menu list
Up
Down
Select
MFC
Clock Edit, PC Comm Mode, and Model Info)
Back
– Increment the value shown above the cursor
Inc
– Decrement the value shown above the cursor
Dec
Next
and Prev are for navigation only.
Done
Edit
Abort
Save
Store
Yes
– negative response to question presented
No
Trim
Thumb operated keys
Up, Select, and Down side keys provide convenient alternate methods of menu navigation. Use these in
addition to Soft keys and numbered HART menu lines to make menu navigation fast and easy.
= Up = Prev
= Select, Edit Do not use these keys when the symbol is displayed.
= Down = Next
Shift, INS
Soft Keys
(unlabeled)
– moves indicator arrow down one line in a menu list
key sequence. Once activated,
– selects the indicated menu item
– provides access to MFC configuration settings (Lockout, Backlight timer, Off timer,
– returns to prior display
/
– these keys move to Next or Previous item within the list function accessed. Next
Prev
– Ends data entry session and proceeds with the selected operation
– activate edit function for displayed parameter
– aborts present operation without affecting prior settings or values
– saves the present value
– stores the present value
– affirmative response to question presented
– executes the trim function called for by the HART menu option selected
BUSY
4
Page 9
GENERAL OPERATION
Power options
The MFC 4100 can be powered for portable operation by two each 9-volt alkaline, Lithium or NiMH
batteries. Alkaline batteries are standard with the MFC shipment. Meriam offers NiMH batteries and
charger cradles (external charge only) as an option. For bench top operations and download operations, an
AC adapter (P/N A36742) is recommended.
Located in the upper right corner of the display, this icon displays the
remaining battery power. Fresh batteries produce a full black cell body. As the power
drains, the black segment retreats indicating remaining power.
When the MFC is used with the optional AC adapter (P/N A36742), the battery circuit is bypassed
and a wall plug icon replaces the battery icon on the display header. The AC adapter jack is located
on the left side of the MFC.
NOTE: Power icons may temporarily disappear during certain HART Communication operations
Navigating Menus on the MFC display
Several methods of navigating through the MFC menus are available to the user for maximum convenience
and utility.
1.
Soft keys
the
the MFC Main displays and HART communication displays.
2.
Side keys
keys are thumb operated and provide a convenient alternative to the Soft Key navigation buttons.
Side key functionality is not always available in the HART communication displays.
3.
Multi-page lists
display indicating the existence of information on the previous or next page(s). Several pages of
information may need to be viewed when reviewing lists of installed DOFs, stored configuration
files or finding a specific device in Offline Mode to create a configuration for. While in these list
areas, pressing the SHIFT key changes soft key definitions
respectively. To quickly advance to the next page of a list, press
key. To retreat to the prior page, press
and
again.
4.
Numbered HART menus
gives fast access directly to the desired menu line. MFC displays also have numbered menus with
the exception of multi-page list screens and the MFC Configuration screen.
5.
HART menu HOME key
HART menu screen for a device, press the
display to the initial HART screen. The Home function will be disallowed if a critical HART task is
in process.
6.
Left / Right Arrow keys
: Use Up and
soft key to accept the indicated choice. Soft key navigating tools are found throughout
Select
: Up,
soft keys remain active until the Up or
PgDn
and
Down
: Multi-page lists have a and/or symbol along the right hand side of the
Soft Keys to move cursor arrow to the desired menu option. Then use
Down
keys are also provided on the left hand side of the MFC. These
Select
and
Select
SHIFT
SHIFT
: All HART displays have numbered menu lines when needed. This
: To quickly retreat from any location in the HART menu to the initial
: Emulate
Back
and then
Down
SHIFT, HOME
and
Select
soft keys, respectively
. After
PgUp
soft key is used or until
key sequence. This will return the
to
Back
and then the
SHIFT
and
PgUp
PgDn
is pressed the
SHIFT
,
PgDn
soft
PgUp
is pressed
5
Page 10
Turning on the MFC
Use the dedicated
ON/OFF
Technologies logo, MFC model number, and MFC firmware version is displayed. A message is displayed
indicating the MFC is scanning for a HART device at address zero. The following scenarios are possible.
1. If the MFC is connected to a HART device with address zero
(and there is sufficient loop resistance), the MFC immediately
establishes HART communication with the device. A display
similar to the example at right appears. The numbered menus
and Soft Keys are then used to commission, re-configure, or
maintain the connected device.
2. If no HART device is connected, a HART device with
address ≠ 0 is connected, or a connected device is not found
due to wiring or loop resistance problem, the MFC will enter
the MFC Main navigation display depicted at right.
2.1 Select
or once the wiring problem is resolved. A proper
connection will be indicated when line two changes
to “
Device 0 *Online*
2.2 Select
is setup for Multi-drop loop or Burst Mode operation
(device address ≠ 0). The MFC will immediately initiate
a multi-drop poll to find all non-zero addresses on the loop.
MFC Main display
The MFC Main display provides access to Online Setup, Offline Menus
and to MFC configuration settings via the right hand Soft Key.
1.
Online Setup
2.
Offline Menu
such as List / Show DOFs, List / Edit Configurations, and Create
Configurations. The number of DOFs installed (HART
device profiles) and the number of device Configurations stored
are also available on Offline Utilities screen.
3.
Soft Key is selected to configure MFC settings and view
MFC
MFC information such as Model, Serial, and Firmware numbers,
DOFs installed and Configurations stored.
key to power up the MFC. A brief diagnostic runs while the Meriam Process
Online #
3051 : PT-1012D
1 Device setup
2 Pres: 0.01 inH2O
3 AO: 4.001 mA
4 LRV: 0.00 inH2O
5 URV: 250.00 inH2O
Up Down Select Back
MFC Main #
Device 0 Not Found
1 Online Setup
2 Offline Menu
Online Setup
once a HART device is connected
”.
Online Setup
if properly connected HART device
is described above in Turning On the MFC.
is selected to provide access to Offline Utilities
6
Up Down Select MFC
MFC Main #
Device 0 *On-line*
1 Online Setup
2 Offline Menu
Up Down Select MFC
Configuration #
Current Settings
Lockout : Disabled
Backlight: 2 min
Off Timer: Disabled
Clock Edit
Enter PC Comm. Mode
Model Info
Up Down Select Back
Page 11
MFC Configurations Settings
Lockout Feature
The MFC HART Communicator can be programmed to lock out certain standard functions that a supervisor
may wish to control. The functions included are used to set up the MFC for normal use, change online
HART device configurations, create offline HART device configurations, update the installed DOFs list
(HART device profiles), or to update the MFC’s operating firmware. For example, locking out the Configs
feature turns the MFC into a read only HART communicator while locking out DOFs and Firmware prevents
unauthorized updates. The lock out can be limited to individual Lockout Details items or all Lockout Details
items can be locked out at one time.
To enable the lockout feature, move the selection cursor to the
Configuration screen (see above). Choose the
will enter the
Lockout Enable / Disable Screen
Lockout
. The current status is shown and three choices are provided:
selection by pressing the
Lockout
Disabled:
Enabled:
View Details:
Configuration #
Lockout : Disabled
Disabled
Enabled
View Details
Up Down Select Back
Lockout Enable / Disable Screen
All lockout features are disabled and all options on the menu are accessible for reconfiguration.
Enables the lockout selections that are set in the
This option takes the user to the
Lockout Details
Lockout Details
screen listing all MFC parameters that can
be protected by lockout (see above left). Individual functions can be locked or, if preferred, the lockout can
be set to deny unauthorized access to all parameters.
To enable the lockout option, select
pressing
. The screen will switch back to the original
Select
Enabled
on
Lockout Enable / Disable Screen
Settings
screen that now shows the lockout
status as Enabled.
Scroll
lockout. Use the Up and
setting(s). The screen will change and prompt you to
Down
Down
to
Enable
to
View Details,
and press
and press
keys to scroll through the selections and press
Down
.
Select
. This screen allows the user to choose which parameters to
Select
Enable
or
Disable
Lockout Code
At this point the user will be prompted to enter a 3-digit lockout code. This code will be required to gain
access and change any parameter previously locked out. Use the
Inc
rement,
to input a lockout code value. Alternatively you may use the green keys for
rement functions. When you are satisfied with the lockout code value, press
Dec
IMPORTANT
: After the code is entered, the user must cycle the power to activate the lockout mechanism!
menu option on the
soft key. The MFC
Select
Configuration #
Lockout Details
All : Disabled
Setting : Disabled
DOFs : Disabled
Configs : Disabled
Firmware : Disabled
Up Down Select Back
Lockout View Details Screen
screen (above left)
by scrolling
Select
to choose the desired
.
Down
lockout for that function. Scroll
rement and
Dec
Store.
Inc
Soft Keys
Next
rement and
and
7
Page 12
BE SURE TO SAVE THIS CODE IN A SAFE PLACE IN THE EVENT YOU FORGET THE NUMBER. ACCESS TO
LOCKED-OUT FEATURES WILL BE DENIED WITHOUT THE PROPER CODE.
To Disable Lockout
When you wish to use a function or edit a value that is protected by the lockout code, enter the three digit
Lockout code when prompted and press
normal. Entering an incorrect code will display the message “Incorrect Code” and allow you to try again.
Changing the Lockout Code
To change the lockout code, disable the lockout function for all the parameters selected, shut the unit off, and
follow the procedures outlined above.
. You will now be able to use the function or edit the setting as
Save
Backlight (off timer)
To conserve battery life, the MFC 4100 series allows the user to set the backlight to shut off after a certain
period of keypad inactivity. To change the backlight off timer on the unit, scroll
press
Select.
The shutoff timer can be disabled or set to shut off after time periods of from 1 minute up to 30 minutes.
NOTE: The Backlight Off Timer is disabled when the optional AC Adapter (P/N A36742) is powering the MFC.
Scroll Up or
Down
to the auto shut-off time desired. Press
to select the new value.
Save
Down
to
Backlight
and
Off Timer
To conserve battery life, the MFC 4100 series allows the user to set the unit to shut off after a certain period
of keypad inactivity. To change the off timer on the unit, scroll
or
Up
The shutoff timer can be disabled or set to shut off after time periods of from 1 minute up to 2 hours.
NOTE: The Off Timer is disabled when the optional AC Adapter (P/N A36742) is powering the MFC.
to the auto shut-off time desired. Press
Down
to select the new value.
Save
Down
to
Off Timer
and press
Select.
Scroll
Clock Edit
The Clock Edit option allows the user to correct the date and time of the MFC’s internal clock. To select the
Clock Edit
using the soft keys. Choose
Choose a clock or date option to adjust by scrolling Up or
the correct value using the numeric keypad and text edit key if needed. When complete, press
will be asked if you wish to save the new data. Press
back to the
NOTE: When replacing the batteries, the date and time will remain active. Date & time information is
continuously powered by an internal, 10-year life back-up battery. This battery is not serviceable by the
user.
feature, make sure the pointer arrow is pointed to this selection. If not, scroll the arrow
Clock Edit
Clock Edit
without making any changes to the MFC clock.
by pressing the
Yes
soft key.
Select
Down.
to accept the new value. Pressing No will take you
Press
Select
to choose that option. Enter
Done
Down
. You
Enter PC Comm. Mode
When the MFC is connected to a PC for updates via MFx Installer (see MFx Installer section in this manual),
a DB-9 serial cable is used. Occasionally a DB-9 Serial cable is encountered that does not have a DTR line.
The DTR line is important to the update process because it is used to initiate and confirm communication
between the two machines. If a DB-9 cable without a DTR line is used, the MFC must be manually placed
8
Page 13
in the
Enter PC Comm. Mode
PC Comm. Mode
menu option and press
. Go to the MFC Main display and select
. Proceed with update and cycle MFC power when the
Select
. Scroll down to the
MFC
Enter
update is complete. It is recommended to use fresh batteries or an AC adaptor during update procedures.
This mode will automatically time-out after approx. 2 minutes of inactivity and return to the main display.
Battery Installation & Removal – all MFC models
The MFC monitors battery condition and displays a “REPLACE BATTERY” notice when the batteries get
low. The MFC will function for a short period of time after the notice is posted.
To install or remove the batteries, remove any soft case or protective boot and turn the MFC face down on a
work surface. Use a flat screwdriver to loosen the captive screw holding the battery door closed and remove
door. Replace batteries and make sure all connections are firmly secured. Replace door, tighten screw and
replace the soft case or boot.
Note: Replace both 9-volt batteries at once with all alkaline, all lithium or all NiMH cells. Do not mix
alkaline, lithium or NiMH batteries with each other or with other battery types. Battery replacement is
recommended when the “Replace Batteries” notice is posted on the display; however, the MFC will
function for a time after the notice is posted.
Note: For Intrinsically Safe MFC models, replace batteries only in Non-Hazardous Areas. Replace
batteries with approved types only. See the MFC Intrinsic Safety Control Document in the Appendix of
this manual for approved battery details.
External Connections to MFC
1. AC Adapter
the left side of the MFC. P/N A36742 bypasses the battery circuit to power the unit. The battery symbol in
the display header is replaced by a wall plug symbol.
WARNING: Serious injury or death may result from explosions. Do not make connection to the AC
adapter jack in a hazardous area. Use the AC adapter only in non-hazardous areas.
2. HART lead set –
lead set supplied with the MFC has a standard banana plug on one end and mini-grabbers on the other for
convenient connections.
Note: For Intrinsically Safe MFC models, verify the instruments in the loop are installed in accordance
with intrinsically safe field wiring practices before making connection from the field device to the MFC’s
HART jack. See Hazardous Area Use Section of this manual for Intrinsically Safe guidelines /
restrictions.
3. DB-9 Connection Port
communications located on the MFC’s bottom end. The DB-9 provides the hardware interface to facilitate
download / upload operations from a host PC. This connection port facilitates download of MFC firmware
improvements, HART
pending). All MFC upgrades are available via the Meriam Process Technologies Download Site accessible
from www.meriam.com. The MFC will not need to be returned to Meriam for firmware updates or for the
addition of DOF files.
Note: Do not use the DB-9 connection port in Hazardous Areas. Use in non-hazardous areas only. See
Intrinsic Safety Control Document in the Appendix for more details on I. S. MFC units.
– The MFC 4100 can be powered by external AC Adapter connected to the jack located on
All MFC models are equipped with a standard size banana jack on 0.75” center. The
– All MFC models are equipped with a standard DB-9 connection for RS-232
®
Device Object Files (DOFs) and documenting operations (Documenting options
9
Page 14
HAZARDOUS AREA USE
Intrinsically Safe Certification
The MFC 4102 and MFC 4103 HART Communicators are available with Intrinsically Safe Certification for
use in Class I, Division I, Groups A, B, C, and D, T5 hazardous areas. Refer to the Intrinsically Safe Control
Document in the Appendix of this instruction manual for more details. The certification is to CAN /CSA-
22.2 No.1010.1 & 157-92 and UL913 Fifth Edition Rev 2/21/97.
The following table identifies MFC model numbers and Areas of acceptable use.
Model Number Non-hazardous
Area
MFC 4100 √ NO
MFC 4101 √ NO
MFC 4102 √ √
MFC 4103 √ √
MFCs with Intrinsically Safe certification can be identified by model number (see table above or the
Intrinsically Safe Control Document in the Appendix) or by a special label on the unit. A sample of the label
is shown below.
WARNING: Serious injury or death may result from explosions. Do not make connection to the DB – 9
connection port or to the AC adapter jack while in a hazardous area.
WARNING: Serious injury or death may result from explosions. Before making electrical connections to
an Intrinsically Safe MFC at the HART jacks, verify the instruments in the loop are installed in
accordance with intrinsically safe field wiring practices.
Note: Restrictions apply to the use of Intrinsically Safe MFC units in hazardous areas. Refer to the
Intrinsically Safe Control Document in the Appendix for exact details. Meriam Process Technologies
reserves the right to revise the Control Document without notice. Contact Meriam Process Technologies
(phone (216) 281-1100) for the current Intrinsically Safe Control Document.
For Intrinsically Safe MFC models, consult the
restrictions, for special instructions in use, and for electrical connections.
Hazardous Area Use
Hazardous
Area
section of this manual for
10
Page 15
HART® Communications with the MFC 4100
Overview
The MFC 4100 HART communicator provides device specific HART communication functions that
allow the user to poll, configure and maintain supported HART field device. The MFC 4100 uses
Universal, Common Practice and Device Specific commands to facilitate communication with a HART
field device. Use the MFC to commission devices, operational re-configuration needs, or maintain
devices through analog and sensor trim adjustments and many other features.
The MFC 4100 will communicate with any HART device through Universal and Common Practice
Commands using the standard Generic DOF (Device Object File) but must have the DOF for a specific
HART device installed before it can execute Device Specific Commands. Consult the large and growing list
of available DOFs at www.meriam.com
The list is found under “Available DOFs” button on the home page. When HART device support for new
devices becomes available, the MFC can be easily field updated via Internet downloads.
for an up to date list of HART devices with device specific support.
HART Commands
Three HART command types are used by the MFC 4100 to communicate with HART field devices. First,
Universal Commands are primarily used to identify a field device by its model number and tag number and
to read process data from the device. This communication is referred to as “polling”. The MFC 4100 can poll
any Hart Device. Second, Common Practice Commands are used for calibration and maintenance functions
that are common to many devices. An example of this would be trims or adjustments for the devices’ analog
outputs. Third, Device Specific Commands are used to handle functions that are unique to a particular device
or manufacturer. Examples of these commands include sensor zero, sensor trim, calibration curve
characterization, density inputs required for calculations made by the HART device or other configuration
functions unique to the specific device.
HART Connections
HART connections are made using two standard banana jacks (3/4” center) located at the top end of the
MFC 4100. Refer to the following diagram. Polarity is not a concern for HART connections so both jack
collars are black. Meriam supplies a HART lead kit (P/N A36744) complete with mini-grabber connections
and a 250 Ω load resistor with each model MFC 4100.
For low load loops (less than 250 Ω), a 250 Ω resistor will need to be added to the loop to insure reliable
HART communications. Meriam supplies a 250 Ω load resistor in the form of a standard adaptor (P/N
A36821). Refer to the following diagram for connection details.
MFC 4100 with HART
HART
®
connections are standard banana jacks (3/4” center)
11
®
Page 16
When connecting the MFC 4100 to a loop with a resistive load greater than 250 Ωs, the HART jacks may be
connected across the loop + and – or to the HART device communication terminals. Refer to the following
diagram for connecting across the loop + and -.
Connecting to the MFC communication terminals
HART® Communications
Upon power up the MFC automatically detects if a field device is connect and attempts to establish HART
communications. When a device with address zero is found, the MFC provides feedback to the user and
starts the initial HART display for the connected device. See an example of Online Mode below.
Online #
3051 : PT-1012D
1 Device setup
2 Pres: 0.01 inH2O
3 AO: 4.001 mA
4 LRV: 0.00 inH2O
5 URV: 250.00 inH2O
Up Down Select Back
Online HART Screen
12
Page 17
p
When no device connection is detected or a device with non-zero (Multi-drop or Burst Mode) address is
found, the message
screen. The
MFC Main
Device 0 Not Found
screen allows the user to launch a multi-drop poll to find all devices with non-zero
is displayed and the MFC enters the
MFC Main
navigation
addresses on the loop, to manually start an Online poll, or to enter Offline Mode.
MFC Main #
Device 0 Not Found
1 Online Setup
2 Offline Menu
Up Down Select MFC
MFC Main Navigation Screen
No device or Non-zero address found
MFC Main #
Multidrop Polling…
Scanning Address #
Stop Abort
Mult-drop Polling Screen
Multi-drop & Burst Mode Support
MFC Main #
Device 0 *On-line*
1 Online Setup
2 Offline Menu
Up Down Select MFC
MFC Main Navigation Screen
Manually launch polling on Device 0
Multi-drop Poll
To initiate a Mult-drop Poll, select the
Not Found
message is displayed. This function polls for all non-zero addresses (1 – 15). Located addresses
Online Setup
option from the
MFC Main
screen when the
Device 0
are listed on the display as the remaining addresses are checked. When polling is complete, or upon pressing
after the address of interest is found, use the soft key controls to select the address of interest. The
Stop
initial HART menu for the device selected will then be displayed for use.
Manual Launch of Device 0 Poll
When the message
Online Setup
will launch HART communication with the device. The message indicates that a HART
Device 0 *On-line*
is displayed on the MFC Main navigation screen, selecting
device with address 0 has been detected at the HART connection and the MFC is standing by to initiate
communications. The
Device 0 *On-line*
message is shown 1) if a physical connection is made to a
HART device after the MFC power is turned on or 2) if the user exits from a HART communication
session using the soft key controls provided.
Offline Menu Mode
The
Offline Menu
gives the user access to lists and functions that can be viewed or performed in Offline
Mode at the user’s convenience for the purposes of reviewing the MFC’s DOF list, reviewing stored device
configurations or creating HART configurations. Stored configurations can be also be edited and then
applied later to a connected HART device. When the
Offline Menu
is selected from the
MFC Main
navigation screen, the following display is shown.
Offline #
Utilities
1 List/Show DOFs
2 List/Edit Configs
3 Create Configs
4 Delete All Configs
DOFs Installed: 154
Configs Stored: 3
U
Down Select Back
Hart Offline Menu Screen
13
Page 18
List / Show DOFs:
Provides a list of installed DOFs (Device Object Files) used by the MFC to communicate with HART
devices. Lists can be view by Manufacturer, by Device Name or by stepping through all Devices one at a
time. Use the soft key controls to move through the list. Pressing the SHIFT key changes soft key
definitions
and then the
and
PgUp
PgDn
.
List / Edit Configs:
This screen lists all stored HART configurations by Tag Number. The
configurations stored enable fast commissioning of replacement devices,
cloning of existing systems, or re-configuring for changes in process
conditions or batch runs. Any configuration in the list can be sent to
another HART device of the same manufacture and model. The display
can show 20 character tag numbers. Truncated tags are listed if more than
20 characters are used. Moving the cursor down to the tag of interest and
pressing the
including full tag number up to 28 characters, for the tag of interest (see
example below, right).
The editing function allows review of all HART parameters in a configuration and modification of editable parameter. The edit function can be
locked out if desired (see the
information). To view detailed information of a stored configuration, Move
the cursor to the desired tag number and press the Select soft key. The
Config Detail screen (see example at right) provides information to help
the user confirm the identity, origin, and save date/time of the configuration.
Pressing Select again opens the configuration for review or offline editing.
New configurations saved are added to the bottom of the List / Edit Config
list. If multiple entries for one device are shown, the most recently saved
configuration is always shown at the bottom.
Entries in the List / Edit Config list may have been saved or created from
various sources. Possible sources include the save command from a
connected HART device, created in the MFC using the
function, copied from another configuration and renamed, or created by
editing an existing file. An MFC with Documenting option (MFC 4101,
MFC 4103) will also list configurations downloaded from the separately
available Device Management System software from Meriam (see www.meriam.com/dm_solns.htm for
more information). Tag numbers, date / time of save, type of configuration stored, and other information
are displayed under
Complete Config = saved from connected device in Online mode, or a
complete config that was downloaded from DMS
Default Config = created by MFC in Offline mode, or created in DMS
and downloaded to MFC
Edit Vars Only = created by editing an existing configuration and includes only the edited parameters
MVar Primary Cfg = for multivariable devices – Primary Variable configuation
MVar Sub Config = for multivariable devices – Sub-configuration (secondary, tertiary, fourth, etc
variables)
Down
PgDn
and Up to
soft key. To retreat to the prior page, press
PgUp
and
PgDn.
soft keys remain active until the Up or
soft key will provide a detailed information screen,
Select
Lockout
List/Edit Configs
section of this manual for more
. Configuration types are:
To quickly advance to the next page of a list, press
SHIFT
soft keys or
Down
Create Configs
and then
SHIFT
. Once engaged, the
PgUp
is pressed again.
Offline #
List/Edit Configs
PT-105A
PT-105B
DPT-201C
TT-312A
TT-312A
FE-201
FE-201
PT-6174
Up Down Select Back
Offline List / Edit
Configs Screen
Offline #
List/Edit Configs
Tag: PT-105A
Device ID 1365
PV: Pressure
Endress + Hauser
Cerabar S
Complete Config
Uses DOF 11070702
51 Variables
12/18/03 4:58 PM
Copy Del Select Back
Offline List / Edit
Configs Detail Screen
SHIFT
14
Page 19
Create Configs:
The
Create Configs
function allows the user to configure a HART device file in Offline Mode for sending
to the intended device later when connected in the Online Mode. Use the soft key controls to move through
the list and select the device model number required. The menus prompt the user to make the necessary
configuration selections, tag the file for later retrieval and use, and edit configuration lines as required. This
function can be locked out. See the Lockout Section of this manual for more information.
Delete All Configs:
The
Delete All Configs
function clears
configurations from memory (including active and hidden
all
configs). When this menu option is selected, the MFC will ask “Delete ALL Configs… ARE YOU
SURE???” Select
Delete Configs / Clearing Configuration Memory:
Individual stored Configurations may be deleted with MFC
functions (see example at right). A delete confirmation screen is provided
to prevent unintended deletions. The
the MFC screen; it does not clear memory space. The editing function
can be locked out. See the Lockout Section of this manual for more
information.
(To clear
configurations from memory (including active and hidden
all
configs), enter the
All Configs
option. The MFC will ask “Delete ALL Configs… ARE
YOU SURE???” Select
memory.)
Yes
to clear
stored configurations from memory.
all
key only hides the record from
Del
HART Offline Menu Screen
Yes
to clear
stored configurations from
all
Del
and select the
soft key
Delete
Offline #
List/Edit Configs
Tag: PT-105A
Device ID 1365
PV: Pressure
Endress + Hauser
Cerabar S
Complete Config
Uses DOF 11070702
51 Variables
12/18/03 4:58 PM
Copy Del Select Back
Offline List / Edit
Configs Detail Screen
Online Setup Mode
Online Setup is the normal HART communication mode for the MFC.
This mode enables communication with HART field devices at the
Universal, Common Practice and Device Specific Command levels for
full device setup and functionality.
Menus displayed for the connected device follow the HART device
manufacturer’s menu structure for the connected device. Consult
the device manual for menu structure details.
MFC features two unique online features for added convenience to the
user.
1. Live HART connection monitor: MFC display lets you
know from the Main navigation screen when a device is
*
On-line *
and ready for communication.
2.
Review/Edit
: this menu option allows the user to review
configurations line-by-line. MFC supports editing of the
configuration once the line of interest is located.
Device Setup #
3051 :PT-1012D
1 Process variables
2 Diag/Service
3 Basic setup
4 Detailed setup
5 Save/Send
6 Review/Edit
Up Down Select Back
Online Device Setup Screen
Communications Trouble Shooting
If an operating HART device is connected to the MFC but the “Device 0 Not Found” notification is
received, a Multidrop Poll may be executed to determine if the connected device has a non-zero address.
15
Page 20
Select
Online Setup
from the MFC Main navigation screen to initiate the multi-drop poll. If the “No
Devices Found” message is received, then the loop connections to the MFC should be carefully checked.
If an operating HART device with address zero (0) is connected to the MFC but the “Device 0 Not Found”
notification is received, the loop connections to the MFC should be carefully checked.
Make sure all connections are correct and secure. Check for shorts, open circuits and multiple grounds.
Determine if the loop resistance is greater than 250Ω and less than 1100Ωs. If less than 250 Ω then use the
supplied 250 Ω load resistor in series with the loop (see diagram HART Connections section).
If communication is still not established, check the
List / Show DOFs
menu under
Offline Menu
. Check
the list for the presence of the “Generic” DOF under the manufacturer name “Meriam.” If “Generic” is
found, then HART communication is possible when the device is properly wired and connected to the MFC
(see connection troubleshooting details above).
When the message “Generic” is displayed after connecting to a HART device there are two possible causes:
1) No device specific DOF for that device is currently installed in MFC memory. Check the Meriam
Download Site for availability of the DOF needed by clicking on the Download Site button at
www.meriam.com
and entering the User Name and Password provided with MFC shipment. For
download instructions, see the DOF Download Site Information section of this manual.
2) The Meriam DOF “Device Library” is missing or has become corrupted. Without this DOF, the
MFC may not recognize a connected device. Check the
Menu
List / Show DOFs
menu option of
Offline
More Status Message
HART device events (diagnostic flags) cause the MFC to display a “More Status Message” at the bottom
of the display. This message is a notice to the user that one or more diagnostic warnings are available in
the Review Status menu option of the connected device. Upon receipt of this message, enter the
HART
mode and select Detailed Setup / Diagnostics – Service / Test – Status / View Status to retrieve the
diagnostic information.
Save / Send Configuration Functions
HART device configurations may be saved to MFC memory or sent from MFC memory to a HART
device in all MFC model numbers. These functions are useful for cloning a device configuration for use
in another transmitter of the same configuration, for recording as-found and as-left configurations for later
review, for returning HART devices to previously used configurations, etc…
The Save / Send function may be accessed in one of two ways:
1. Press the Document key on the MFC for the
screen shown at right. Then select the “Save/Send
Configs” menu option to launch a HART communication poll and use the Save / Send options.
Use the Save / Send menu option within the HART
2.
device’s standard menu. The MFC would be in
Online mode in this case. Save / Send is normally
found under the “Device Setup” menu option on the
initial HART display for the device.
Document #
Utilities
1 Save/Send Configs
2 List/Edit Configs
3 Create Configs
Configs Stored: 98
Up Down Select Back
Document Key Menu Screen
16
Page 21
b
Documenting HART Configurations with Meriam DMS software
The Documentation order option for MFC 4101 and MFC 4103 models
provides additional functionality for use with the Meriam Device
Management System (DMS) software. DMS is a database product for
complete device management services including calibration with the
Meriam MFT 4000 Series of multifunction calibrators and HART
configuration documentation with the MFC 4101 and 4103.
Complete device histories are maintained in the database. For
HART devices these histories can include as-found and as-left
HART configuration data to complete this important part of a
device’s history.
MFC 4101 / 4103 with Meriam
Device Management System
The Document key on the MFC 4101 and MFC 4103
models will save configurations in as-found or as-left
categories as selected by the user. These configuration files
can be uploaded later to DMS. When the
menu option is selected the MFC automatically polls for an
Online device for subsequent user selections.
DMS can also be used as a configuration repository ready to
download stored device configurations for batch runs or
changes in operating requirements. New configurations can
e downloaded to MFC memory for later recall and use in the
field.
Document #
Utilities
1 Save/Send Configs
2 List/Edit Configs
3 Create Configs
Configs Stored: 98
Up Down Select Back
Document Key Menu Screen
Save/Send Configs
MFC 4100 Device Specific & Generic HART® Communications
Meriam supports a large and growing number of Device Specific DOFs (Device Object Files). For a current
listing of HART
on the “Available DOFs” button. Information found there can be sorted by manufacturer name or model
number.
®
devices with full Device Specific communication support, go to www.meriam.com and click
To facilitate communication with HART devices that are not yet supported with Device Specific DOF files or
that do not require DOF files, the MFC 4100 includes Generic HART Communication capability. This allows
the user to communicate with any HART device using Universal and Common Practice commands to poll,
configure, and maintain HART devices. Specific functions supported include most polling, tagging, device
configuration and trim operations for analog outputs. Generic communications do not support Device Specific
commands for higher order HART functions (see the
instruction manual for the HART device of interest for more information on the three command levels).
Using Generic HART Communication
The MFC 4100’s Generic HART Communication mode starts automatically when HART communication is
initiated with a device for which no Device Specific DOF (device object file) is found to match the connected
HART
17
®
Commands
section of this manual or the
Page 22
HART device name. When this occurs, line two of the display will indicate “Generic” and the device tag
number.
In general, the Generic HART mode operates similarly to its device specific DOF counterpart (see HART
Communication section of this manual for more details). However, the MFC does not display Device Specific
related communication menus or options when in the Generic communication mode. For example, the Zero and
Sensor trim menu options (normally executed by Device Specific commands) are not displayed for pressure
transmitters without DOF support. Please see the
downloading the latest Device Specific DOF files to your MFC.
Download Site
section of this manual for information on
DOF / Firmware Download Site
Overview
One of the unique features of the MFC 4100 Series is the built-in ability to have firmware upgrades installed
by the user at his location. The Meriam Download Site is accessible over the Internet and provides for the
convenient download of new or revised firmware and DOF’s (Device Object Files) for HART
communication. MFC units already in service in the field do not need to be returned to the factory for
firmware upgrades or improvements released by Meriam. The user can simply download the files to a PC
having Internet access and upgrade the MFC firmware using the MFx Installer PC utility. DOF’s are also
available on this site. The Download Site enables users to stay current as Meriam releases new DOF’s or
revisions of existing ones.
Who has access to the Download Site?
All MFC purchasers have unlimited access to the Download Site for six months from date of shipment.
These customers may download any published file from the site to their MFC upon entry of the proper
authenticating codes (shipped with unit). After the initial six-month period, the Download Site is available
with paid annual subscription fee. Contact Meriam Process Technologies at (216) 281-1100 or
meriam@meriam.com
PC Requirements for Download Operations
Meriam recommends IBM compatible Pentium I PCs or higher for download operations. The PC should
have an available RS-232 port, minimum modem speed of 28K and access to Internet service.
Preparing the MFC
All MFC models come ready to connect to an IBM compatible PC using the DB-9 socket located at the
bottom of the MFC enclosure. A six-foot male DB-9 to female DB-9 cable (P/N A90047-00052) is available
from Meriam. Similar cables are acceptable. Connect the MFC to the PC and power up the MFC using
fresh internal batteries or the optional AC Adapter (P/N A36742). The MFC is ready for download
operations.
Preparing to Download
Establish connection to the Download Site by going to the Meriam Process Technologies website at
www.meriam.com
download functions. A list of currently available DOF’s for HART device communication can be viewed at
the www.meriam.com
an up to date list of available DOF’s.
for more information and to purchase annual subscriptions.
. Click on the “Download Site” button on the home page navigation bar to access all
website. Click the “Available DOFs” button on the home page navigation bar to view
18
Page 23
Using the Download Site
The landing page of the Download Site requires the user to enter a valid User Name and Password to
authenticate user identity and permit entry to the Site. These two codes are initially assigned by Meriam and
can be found on a card included with shipment. Locate the card and place in a safe place for future
reference.
Once a user is logged on to the Site, the
recent firmware releases posted and the posting date. Individual files can be downloaded from the detailed
description page of each DOF or firmware file listed. Also available on this screen are the navigation
buttons for
The
Current Release Notes
Five (5) columns are shown on this page: Date, Title, Description, Manufacturer, Model. These categories
will assist the user in finding the release descriptions of the DOF, MFC Installer or MFC Firmware releases
of interest. Individual files can be downloaded from the detailed description page of each DOF or firmware
file listed. Each column can be sorted to assist searches of the release database. Also available on this screen
are the navigation buttons for
The
File Download Area
files (including MFx Installer Utility, MFC Firmware, MFC Documentation Firmware
and DOF’s) by locating the file name of interest with the PC mouse and left clicking. Dialog boxes guide the
user through the process. Multiple files can be downloaded using a Java applet that must first be loaded onto
the host PC. Dialog boxes again guide the user through the process. Subsequent downloads of multiple files
will be handled by the Java applet stored in the host PC memory. Also available on this screen are the
navigation buttons for
Subscriber Options
The
Subscriber Options
account are listed, as well as the subscription expiration date. In addition, this screen allows the user to
customize the account Password. The user should also provide an e-mail address that allows Meriam to
provide notification of new firmware updates, DOF releases, and subscription period expiration. Press the
“Update Subscriber Options” button to save all
To report any difficulties with downloading operations, please contact Meriam Process Technologies at
(216) 281-1100 or meriam@meriam.com.
Current Release Notes, File Download Area
screen describes the most recent firmware releases available and dates posted.
Latest Release Notes, File Download Area
screen is the actual download page. Select from a list of downloadable firmware
Latest Release Notes, Current Release Notes
screen provides useful account information. User Name and Password for the
Latest Release Notes
Subscriber Options
screen appears listing and describing the most
, and
Subscriber Options
, and
changes.
, and
Subscriber Options
.
Subscriber Options
.
.
MFx Installer Utility
MFx Installer utility should be loaded onto the host PC from the instruction manual CD (included with MFC
shipment) or from the Meriam Download Site where it can be found on the
Installer coordinates the download operations from the host PC to the MFC. Periodic improvements may be
incorporated into this Utility. Therefore, Meriam recommends periodic comparison of the MFx Installer
version installed on the host PC to the latest available version on the Download Site to insure use of the an
up to date Utility tool. Directions for using MFx Installer are found under the Help Tool Bar selection.
File Download Area
page. MFx
19
Page 24
RETURNING THE MFC FOR REPAIR
In the event that a MFC requires service and must be returned to the factory for repair, please contact your
local Meriam Process Technologies Representative (see list and contact information at www.meriam.com
contact the factory direct at the numbers listed below.
Please do not send any unit in for repair without first contacting Meriam Process Technologies or
Representative for a Return Material Authorization (RMA) number.
This number will be provided by
the Meriam Repair Department when you call, fax or e-mail your information. An RMA number must
accompany all incoming packages to insure proper tracking, processing and repair work.
To assist us in processing your repair request, please have the Model & Serial Number of the unit available
when you call. This information is located on the MFC label. This information can also be obtained directly
from the MFC display by pressing the
Soft Key from the
MFC
MFC Main
display. See the MFC Main
display section in this manual for more details.
Meriam Process Technologies
10920 Madison Avenue
Cleveland, Ohio 44102
TELEPHONE: (216) 281-1100
FAX: (216) 281-0228
E-mail: meriam@meriam.com
Web Site: www.meriam.com
) or
20
Page 25
APPENDIX
PRODUCT SPECIFICATIONS OVERVIEW
BASE UNIT: 10" L x 4.25" W x 1.65"D ABS plastic case with optional shock absorbing boot, 19ozs. including
batteries
DISPLAY: 128 x 128 pixel graphic display, 2.6” x 2.6” viewable area, backlight
POWER: two (2) 9-volt alkaline batteries, two (2) 9-volt Lithium batteries, two (2) 9-volt NiMH batteries or optional
100 – 240 Vac power adapter (P/N A36742)
TEMPERATURE SPECIFICATIONS:
Storage: -40° F to 140° F (-40° C to 60° C)
Operating: 23° F to 122° F (-5° C to 50° C)
CONNECTIONS: HART: Standard banana jacks (½” center)
PC Data transfer: DB-9 serial connector
Power: AC Adapter jack
AUTO SHUT-OFF - occurs after user-selected period of keypad inactivity or can be disabled, both MFC and backlight
DIAGNOSTICS – MFC 4100 self-tests upon power up. Advisories are posted on the display.
APPROVALS: Class I, Div I, Groups A, B, C, D, T5 certified by MET Laboratories, Inc per UL3111-1, CAN/CSA-
22.2 No. 1010.1 & 157-92 and UL913, Fifth Edition, Rev. 2/21/97
CONTRAST – direct adjustment of display contrast in any mode; automatic compensation for ambient temperature
changes
SECURITY LOCKOUT – MFC 4100 Settings can be locked out entirely or by specific feature.
CE compliance
MEMORY – separate, dedicated, non-volatile flash memory for MFC firmware, DOFs, and Configurations
DOF Memory: 600 HART devices (based on average DOF size)
Configuration Memory: 200 HART devices (based on average configuration size)
BASE UNIT MODEL No & DESCRIPTION:
MFC 4100 HART Communicator
MFC 4101 HART Communicator with Documenting capability (via Meriam DMS software)
MFC 4102 HART Communicator with Intrinsically Safe certification. I.S. certification by MET
Laboratories per testing to UL3111-1 First Edition Rev. 6/30/94, CAN/CSA-22.2 No. 1010.1 &
157-92 and UL913 Fifth Edition
MFC 4103 HART Communicator with both Documenting and Intrinsically Safe certification
ORDER OPTIONS
-0 Rear hand strap only: no carrying case, no protective boot required
-1 Fitted, use-in-place, soft carrying case with adjustable shoulder strap and pocket for HART leads
-2 Slip-on, protective red boot with adjustable, detachable hanging strap
ORDERING INFORMATION
21
Page 26
ACCESSORIES
A36885 Protective red boot provides degree of protection against drop related damage; slip on
A900529-00014 HART Test Lead Kit (inc'd w/ MFC) - std banana plugs, mini-grabbers, 250 Ω
resistor
A36821 Std size 250 Ω shunt resistor (inc'd w/ MFC) - req'd for HART low resistance loops
A900447-00052 DB-9 cable, Male x Female, 6 ft length
A36875 MFC carrying case (inc'd w/ MFC) - custom soft case with adjustable shoulder strap
and HART lead compartment
A36884 Adjustable, detachable hanging strap (inc'd w/ MFC) clips directly to MFC attach
points
A900614-00006 9 Volt Alkaline Battery (inc'd w/ MFC) (2 req'd)
A900614-00009 9 Volt Lithium Battery (2 req'd), approx 3x life of alkaline batteries, best for cold
service
A900614-00015 Volt NiMH Batteries (2 req'd), approx 2x life of alkaline batteries
A36888 NiMH battery charger
A36742 Power adapter, 100 Vac to 240 Vac, 50-60 Hz
A36755 Universal plug adapter kit for A36742 power adapter
F/N 4100:440 Paper instructions for MFC 4100 (PDF instructions sent with each MFC on CD)
22
Page 27
Intrinsic Safety Control Document
23
Page 28
Send
1151 Rev. 5 Menu Tree
Device Setup
PV
AO
URV
LRV
% of Range
Process Vars
Sensors
Analog Trim
Basic Info
Hart Output
Diagnostics
Save / Send
Review / Edit
Pressure Value
Pressure Percent Range
Analog Output
Pressure Trim
Re Range
Signal Cond
Pressure Output Transfer Function
Pressure Damping Value
Pressure Units
Analog Output Alarm Select
Trim 4mA
Trim 20mA
Loop Test
Tag
Date
Descriptor
Message
Private Label
Revisions
Const Mats
Polling Address
Burst Mode Select
Burst Com Number
Device ID
Preambles
Self Test
Loop Test
Save
Variables
HART Revision
Device Revision
Software Revision
Final Assembly Number
Perform Test
Test Results
Zero Trim
Lower Sensor Trim
Upper Sensor Trim
Lower Sensor Trim Point
Upper Sensor Trim Point
Pressure Lower Range Value
Pressure Upper Range Value
Set 4mA Range
Set 20mA Range
Pressure Lower Range Limit
Pressure Upper Range Limit
Module Isolator Material
Module Fill Fluid
Gasket Material
Flange Material
Drain Vent Material
Flange Type
Remote Seal Isolator
Material
Flange Size
Number of Remote Seals
Remote Seal Fill Fluid
Remote Seal Type
24
Page 29
Send
3051C Rev. 2 Menu Tree
Device Setup
Press
AO
URV
LRV
Process Vars
Sensors
Analog Trim
Basic Info
Hart Output
Diagnostics
Save Send
Review Edit
Pressure Value
Pressure Percent Range
Analog Output
Temperature Value
Sensor Trim
Re Range
Signal Cond
Units
Pressure Units
Temperature Units
Trim 4mA
Trim 20mA
Loop Test
Tag
Date
Descriptor
Message
Revisions
Const Mats
Device ID
Polling Address
Request Preambles
Burst Mode Select
Burst Command Number
Self Test
Loop Test
Save
Variables
Zero Trim
Lower Sensor Trim
Upper Sensor Trim
Lower Sensor Trim Point
Upper Sensor Trim Point
Pressure Lower Range Value
Pressure Upper Range Value
Set 4mA Range
Set 20mA Range
Pressure Lower Range Limit
Pressure Upper Range Limit
Pressure Units
Pressure Output Transfer Function
Pressure Damping Value
Analog Output Alarm Select
Universal Revision
Transmitter Revision
Software Revision
Final Assbly Number
Self Test
Status Display
Module Isolator Material
Module Fill Fluid
Gasket Material
Flange Material
Drain Vent Material
Flange Type
Remote Seal Isolator
Material
Flange Size
Number of Remote Seals
Remote Seal Fill Fluid
Remote Seal Type
25
Page 30
N
Send
EJA Rev. 2 Menu Tree
Device Setup
Press
AO
URV
LRV
Process
Vars
Sensors
Analog
Trim
Basic Info
Hart Output
Display
Cond
Write
Protect
Diagnostics
Save Send
Review
/Edit
Pressure Value
Pressure Percent Range
Analog Output
Temperature Value
Static Pressure Value
Engr Display Unit
Engr Display Value
Sensor Trim
Re Range
Signal Cond
Units
Pressure Units
H20 Unit Select
Temperature
Units
Trim 4mA
Trim 20mA
Loop Test
Tag
Date
Descriptor
Message
ASC Model
Ext SW
Mode
Revisions
Const Mats
Device ID
Polling Address
Request Preambles
Burst Mode Select
Burst Command Number
Disp Mode
Disp Func
Engr Disp
Write Protect
Write Enable 10min
New Password
Self Test
Loop
Save
Variables
Self Test
Status Display
Zero Trim
Lower Sensor Trim
Upper Sensor Trim
Lower Sensor Trim Point
Upper Sensor Trim Point
Pressure Lower Range Value
Pressure Upper Range Value
Set 4mA Range
Set 20mA Range
Pressure Lower Range Limit
Pressure Upper Range Limit
Pressure Units
H2O Unit Select
Low Cut Point
Low Cut Mode
Bi Dir Mode
Pressure Output Transfer Function
Pressure Damping Value
Analog Output Alarm Select
Module Isolator
Material
Universal
Revision
Transmitter
Revision
Software
Engr Display Unit
Engr Disp LRV
Engr Disp URV
Engr Disp Point
Module Fill Fluid
Gasket Material
Flange Material
Drain Vent
Material
Flange Type
Remote Seal
Isolator Material
Flange Size
umber of Remote
26
Page 31
N
Send
EJA Rev. 1 Menu Tree
Device Setup
Press
AO
URV
LRV
Process
Vars
Sensors
Analog
Trim
Basic Info
Hart Output
Display
Cond
Write
Protect
Diagnostics
Save Send
Review
/Edit
Pressure Value
Pressure Percent Range
Analog Output
Temperature Value
Static Pressure Value
Engr Display Unit
Engr Display Value
Sensor Trim
Re Range
Signal Cond
Units
Pressure Units
H20 Unit Select
Temperature Units
Static Pressure Units
Trim 4mA
Trim 20mA
Loop Test
Tag
Date
Descriptor
Message
ASC Model
Ext SW
Mode
Revisions
Const Mats
Device ID
Polling Address
Request Preambles
Burst Mode Select
Burst Command Number
Disp Mode
Disp Func
Engr Disp
Write Protect
Write Enable 10min
New Password
Software Seal
Self Test
Loop
Self Test
Status Display
Save
Variables
Zero Trim
Lower Sensor Trim
Upper Sensor Trim
Lower Sensor Trim Point
Upper Sensor Trim Point
Pressure Lower Range Value
Pressure Upper Range Value
Set 4mA Range
Set 20mA Range
Pressure Lower Range Limit
Pressure Upper Range Limit
Pressure Units
H2O Unit Select
Low Cut Point
Low Cut Mode
Bi Dir Mode
Pressure Output Transfer Function
Pressure Damping Value
Analog Output Alarm Select
Universal
Revision
Transmitter
Revision
Software
Engr Display Unit
Engr Disp LRV
Engr Disp URV
Engr Disp Point
Module Isolator
Material
Module Fill Fluid
Gasket Material
Flange Material
Drain Vent
Material
Flange Type
Remote Seal
Isolator Material
Flange Size
umber of Remote
27
Loading...