Mercusys MR70X User guide

Download

Page 1

User Guide

AX1800 Dual-Band Wi-Fi 6 Router

MR70X/MR1800X

REV2.0.0 1910080081

Page 2

Specications are subject to change without notice. trademark of MERCUSYS TECHNOLOGIES CO., LTD. Other brands and product names are trademarks or registered trademarks of their respective holders.

No part of the specications may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from MERCUSYS TECHNOLOGIES CO., LIMITED. Copyright © 2022 MERCUSYS TECHNOLOGIES CO., LIMITED. All rights reserved.

http://www.mercusys.com

is a registered

Page 3

CE Mark Warning

This is a class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures.

OPERATING FREQUENCY (the maximum transmitted power)

2412 MHz -2472MHz (20 dBm)

5150 MHz -5250 MHz (23 dBm)

EU Declaration of Conformity

Mercusys hereby declares that the device is in compliance with the essential requirements and other relevant provisions of directives 2014/53/EU, 2009/125/EC, 2011/65/EU and

(EU)2015/863.

The original EU Declaration of Conformity may be found at http://www.mercusys.com/en/ce.

RF Exposure Information

This device meets the EU requirements (2014/53/EU Article 3.1a) on the limitation of exposure of the general public to electromagnetic elds by way of health protection.

The device complies with RF specications when the device used at 20 cm from your body.

National restrictions

Attention: This device may only be used indoors in all EU member states, EFTA countries and Northern Ireland.

AT BE BG CH CY CZ DE DK

EE EL ES FI FR HR HU IE

IS IT LI LT LU LV MT NL

NO PL PT RO SE SI SK UK(NI)

UK Declaration of Conformity

Mercusys hereby declares that the device is in compliance with the essential requirements and other relevant provisions of the Radio Equipment Regulations 2017.

The original UK Declaration of Conformity may be found at https://www.mercusys.com/support/ukca/

National restrictions

Page 4

Attention: This device may only be used indoors in Great Britain.

Продукт сертифіковано згідно с правилами системи УкрСЕПРО на відповідність вимогам нормативних документів та вимогам, що передбачені чинними законодавчими актами України.

NCC Notice & BSMI Notice:

注意！

取得審驗證明之低功率射頻器材，非經核准，公司、商號或使用者均不得擅自變更頻率、

加大功率或變更原設計之特性及功能。

低功率射頻器材之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，應立

即停用，並改善至無干擾時方得繼續使用。

前述合法通信，指依電信管理法規定作業之無線電通信。

低功率射頻器材須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干擾。

應避免影響附近雷達系統之操作。

高增益指向性天線只得應用於固定式點對點系統。

安全諮詢及注意事項

Ǵ請使用原裝電源供應器或只能按照本產品注明的電源類型使用本產品。

Ǵ清潔本產品之前請先拔掉電源線。請勿使用液體、噴霧清潔劑或濕布進行清潔。

Ǵ注意防潮，請勿將水或其他液體潑灑到本產品上。

Ǵ插槽與開口供通風使用，以確保本產品的操作可靠並防止過熱，請勿堵塞或覆蓋開口。

Ǵ請勿將本產品置放於靠近熱源的地方。除非有正常的通風，否則不可放在密閉位置中。

Ǵ請不要私自打開機殼，不要嘗試自行維修本產品，請由授權的專業人士進行此項工作。

Page 5

設備名稱：AX1800Dual-BandWi-Fi6Router

Equipmentname

單元

Unit

PCB

限用物質含有情況標示聲明書

型號（型式）：MR70X/MR1800X

Typedesignation(Type)

限用物質及其化學符號

Restrictedsubstancesanditschemicalsymbols

鉛

Lead

(Pb)

汞

Mercury

(Hg)

鎘

Cadmium

(Cd)

六價鉻

Hexavalent

chromium

)

(Cr

多溴聯苯

Polybrominated

biphenyls

(PBB)

○ ○ ○ ○ ○ ○

多溴二苯醚

Polybrominated

diphenylethers

(PBDE)

外殼

電源供

應器

天線

○ ○ ○ ○ ○ ○

−

○ ○ ○ ○ ○

○ ○ ○ ○ ○ ○

備考1."超出0.1wt%"及"超出0.01wt%"系指限用物質之百分比含量超出百分比

含量基準值。

備考2."○"系指該項限用物質之百分比含量未超出百分比含量基準值。

備考3."−"系指該項限用物質為排除項目。

Safety Information

Ǵ Keep the device away from water, re, humidity or hot environments.

Ǵ Do not attempt to disassemble, repair, or modify the device. If you need service, please

Ǵ Do not use damaged charger or USB cable to charge the device.

Ǵ Do not use any other chargers than those recommended

Ǵ Do not use the device where wireless devices are not allowed.

Ǵ Adapter shall be installed near the equipment and shall be easily accessible.

Ǵ Use only power supplies which are provided by manufacturer and in the original packing

of this product. If you have any questions, please don't hesitate to contact us.

Ǵ Operating Temperature: 0°C~40°C (32°F~104°F)

Ǵ This product uses radios and other components that emit electromagnetic elds.

Electromagnetic elds and magnets may interfere with pacemakers and other implanted medical devices. Always keep the product and its power adapter more than 15 cm (6 inches) away from any pacemakers or other implanted medical devices. If you suspect your product is interfering with your pacemaker or any other implanted medical device, turn o your product and consult your physician for information specic to your medical device.

Please read and follow the above safety information when operating the device. We cannot

Page 6

guarantee that no accidents or damage will occur due to improper use of the device. Please use this product with care and operate at your own risk.

Explanation of the symbols on the product label

Symbol

Explanation

Class II equipment

Alternating current

DC voltage

Indoor use only

Polarity of output terminals

Energy efficiency Marking

Caution

Operator’s manual

RECYCLING

This product bears the selective sorting symbol for Waste electrical and electronic equipment (WEEE). This means that this product must be handled pursuant to European directive 2012/19/EU in order to be recycled or dismantled to minimize its impact on the environment.

User has the choice to give his product to a competent recycling organization or to the retailer when he buys a new electrical or electronic equipment.

Page 7

Contents

Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 01

Chapter 1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 02

1. 1. Product Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .02

1. 2. Product Appearance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .02

1. 2. 1. Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .02

1. 2. 2. Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 03

Chapter 2. Connect to the Internet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 04

2. 1. Position Your Router . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .04

2. 2. Connect to the Internet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .04

Chapter 3. Log In to the Router . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 06

Chapter 4. Configure the Router in Wireless Router Mode . . . . . . . . . . . . . . . 07

4. 1. Operation Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 07

4. 2. Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 08

4. 2. 1. Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .08

4. 2. 2. Internet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 09

4. 2. 3. MAC Clone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

4. 2. 4. LAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16

4. 2. 5. IPTV/VLAN. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16

4. 2. 6. DHCP Server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

4. 2. 7. Dynamic DNS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

4. 2. 8. Static Routing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20

4. 3. Wireless . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21

4. 3. 1. Wireless Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21

4. 3. 2. Guest Network. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23

4. 3. 3. Wireless Schedule . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24

4. 3. 4. WPS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25

4. 3. 5. Additional Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27

4. 4. NAT Forwarding. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28

4. 4. 1. Port Forwarding. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28

4. 4. 2. Port Triggering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30

4. 4. 3. UPnP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31

4. 4. 4. DMZ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32

4. 5. Parental Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33

Page 8

4. 6. QoS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35

4. 7. Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36

4. 7. 1. Firewall . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

4. 7. 2. Access Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37

4. 7. 3. IP & MAC Binding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39

4. 7. 4. ALG. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40

4. 8. VPN Server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40

4. 8. 1. OpenVPN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41

4. 8. 2. PPTP VPN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42

4. 9. IPv6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46

4. 10. System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49

4. 10. 1. Firmware Upgrade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

4. 10. 2. Backup & Restore . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50

4. 10. 3. Change Password. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51

4. 10. 4. Local Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51

4. 10. 5. Remote Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52

4. 10. 6. System Log. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .54

4. 10. 7. Diagnostics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55

4. 10. 8. Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56

4. 10. 9. Language. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58

4. 10. 10.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Reboot 58

4. 10. 11.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . LED

Control 59

Chapter 5. Configure the Router in Access Point Mode . . . . . . . . . . . . . . . . . . 60

5. 1. Operation Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60

5. 2. Firmware Upgrade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .61

5. 3. Backup & Restore. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .61

5. 4. Administration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .62

5. 4. 1. Change Password. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .62

5. 4. 2. Local Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .63

5. 5. System Log. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .64

5. 6. Diagnostics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .64

5. 7. Time. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .66

5. 8. Language. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .67

5. 9. Reboot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .67

5. 10. LED Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .68

FAQ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70

Page 9

Conventions

The router mentioned in this User Guide stands for MR70X/MR1800X AX1800 Dual-

Band Wi-Fi 6 Router without any explanations.

Parameters provided in the pictures are just references for setting up the product,

which may dier from the actual situation.

You can set the parameters according to your demand.

More Info

Specications and the latest software can be found at the product page at the ocial

website http://www.mercusys.com.

The Quick Installation Guide can be found where you nd this guide or inside the

package of the router.

*Maximum wireless signal rates are the physical rates derived from IEEE Standard

802.11 specications. Actual wireless data throughput and wireless coverage are not

guaranteed and will vary as a result of 1) environmental factors, including building

materials, physical objects, and obstacles, 2) network conditions, including local

interference, volume and density of trac, product location, network complexity, and

network overhead, and 3) client limitations, including rated performance, location,

connection, quality, and client condition.

*Use of 802.11ax (Wi-Fi 6), and features including OFDMA, MU-MIMO, 1024-QAM,

BSS Color, and Target Wake Time requires clients to also support the corresponding

features. Actual power reduction by Target Wake Time may vary as a result of network

conditions, client limitations, and environmental factors.

*Use of WPA3 requires clients to also support WPA3.

Page 10

Chapter 1 Introduction

Chapter 1. Introduction

1. 1. Product Overview

Equipped with next-gen Wi-Fi 6, both 5 GHz and 2.4 GHz are upgraded to the latest generation, supporting combined speeds of up to 1800 Mbps – 1201 Mbps on 5 GHz and 574 Mbps on 2.4 GHz. Game online, watch 4K videos, and crank up everything to the highest settings without lag. The router delivers exceptional range and speed, which can fully meet the need of Small Office/Home Office (SOHO) networks and the users demanding higher networking

performance.

1. 2. Product Appearance

1. 2. 1. Front Panel

The router’s System LED is located on the front panel.

Status Indication

Off Power is off.

Solid on: The router is functioning normally and the wireless networks are enabled.

Green

Orange Solid on: The wireless networks are disabled.

Flashing quickly: The WPS connection is in progress Flashing slowly: The router is starting up or upgrading.

Page 11

Chapter 1 Introduction

1. 2. 2. Rear Panel

The following items are located on the rear panel (View from left to right).

Item Description

POWER Socket

RESET/WPS Button

WAN Port This port is where you will connect the router to the DSL/cable Modem, or Ethernet.

LAN Ports These ports connect the router to the local devices.

Wireless Antennas To receive and transmit the wireless data.

The power socket is where you will connect the power adapter. Please use the power adapter provided with this router.

Press and hold this button for more than 5 seconds to reset the router.

Press for 1 second to use the WPS function.

Item Indication

WAN Port LED

LAN Port LED

Off: The WAN port is not connected. On: The WAN port is connected.

Off: The LAN port is not connected. On: The LAN port is connected.

Page 12

Chapter 2

Modem

INTERNET

Router

Power adapter

Connect to the Internet

Chapter 2. Connect to the Internet

2. 1. Position Your Router

• The product should not be located in a place where it will be exposed to moisture or excessive heat.

• Place the router in a location where it can be connected to multiple devices as well as to a power source.

• Make sure the cables and power cord are safely placed out of the way so they do not create a tripping hazard.

• The router can be placed on a shelf or desktop.

• Keep the router away from devices with strong electromagnetic reference, such as

Bluetooth devices, cordless phones and microwaves.

2. 2. Connect to the Internet

1. Follow the steps below to connect your router.

If your Internet connection is through an Ethernet cable from the wall instead of through a DSL/Cable/Satellite modem, connect the Ethernet cable directly to the router’s Internet port, then follow sub step 4) to complete the hardware connection.

*Image may differ from actual product.

1 ) Turn off the modem, and remove the backup battery if it has one.

2 ) Connect the modem to the router’s WAN port with an Ethernet cable.

3 ) Turn on the modem, and then wait about 2 minutes for it to restart.

4 ) Turn on the modem..

Page 13

Chapter 2

Connect to the Internet

2. Connect your computer to the router.

• Method 1: Wired

Turn off the Wi-Fi on your computer and connect your computer to the router’s LAN port using an Ethernet cable.

• Method 2: Wirelessly

1 ) Find the SSID (Network Name) and wireless password printed on the label at the

bottom of the router.

2 ) Click the network icon of your computer or go to Wi-Fi Settings of your smart device,

then select the SSID and enter the wireless password to join the network.

3. Enter http://mwlogin.net in the address bar of a web browser. Create a password to log in.

Note:

If the login window does not appear, please refer to the FAQ section.

4. Follow the Quick Setup to set up the internet connection.

5. Enjoy! For wireless devices, you may have to reconnect to the wireless network if you

have customized the SSID (wireless name) and password during the configuration.

Page 14

Chapter 3 Log In to the Router

Chapter 3. Log In to the Router

This chapter introduces how to log in to the web management page of the router.

With the web-based utility, it is easy to configure and manage the router. The web-based utility can be used on any Windows, Macintosh or UNIX OS with a Web browser, such as Microsoft the Internet Explorer, Mozilla Firefox or Apple Safari.

Follow the steps below to log in to your router.

1. Set up the TCP/IP Protocol in Obtain an IP address automatically mode on your computer.

2. Visit http://mwlogin.net, create a password to log in.

Note:

If the login window does not appear, please refer to the FAQ section.

Page 15

Chapter 4 Congure the Router in Wireless Router Mode

Chapter 4. Congure the Router in Wireless Router Mode

This chapter presents how to configure the various features of the router working as a wireless router.

It contains the following sections:

• Operation Mode

• Network

• Wireless

• NAT Forwarding

• Parental Controls

• QoS

• Security

• VPN Server

• IPv6

• System

4. 1.

1. Visit http://mwlogin.net, and log in with the password you set for the router.

2. Go to System > Operation Mode.

3. Select the working mode as needed and click SAVE.

Operation Mode

Page 16

Chapter 4 Congure the Router in Wireless Router Mode

4. 2. Network

4. 2. 1. Status

1. Visit http://mwlogin.net, and log in with password you set for the router.

2. Go to Advanced > Network > Status. You can view the current status information of the

router.

• Internet - This field displays the current settings of the internet, and you can configure

them on the Advanced > Network > Internet page.

Page 17

Chapter 4 Congure the Router in Wireless Router Mode

• Status - Indicates whether the router has been connected to the internet.

• Internet Connection Type - Indicates the way in which your router is connected to

the internet.

• IP Address - The WAN IP address of the router.

• Subnet Mask - The subnet mask associated with the WAN IP address.

• Default Gateway - The Gateway currently used is shown here. When you use

Dynamic IP as the internet connection type, click Renew or Release here to obtain new IP parameters dynamically from the ISP or release them.

• Primary & Secondary DNS - The IP addresses of DNS (Domain Name System)

server.

• LAN - This field displays the current settings of the LAN, and you can configure them on

the Advanced > Network > LAN page.

• MAC Address - The physical address of the router.

• IP Address - The LAN IP address of the router.

• Subnet Mask - The subnet mask associated with the LAN IP address.

• DHCP Server - This field displays the current settings of DHCP (Dynamic Host

Configuration Protocol) Server, and you can configure them on the Network > DHCP Server page.

• DHCP Server - Indicates whether the DHCP server is enabled of disabled. It is

enabled by default and the router acts as a DHCP server.

• IP Address Pool - The IP address range for the DHCP server to assign IP addresses.

• Dynamic DNS - This field displays the current settings of the Dynamic DNS (Domain

Name System), and you can configure them on the Advanced > Network > Dynamic DNS page.

• Service Provider - The Dynamic DNS service provider you have signed up for.

• Host Name - The Domain Name you have entered in the Dynamic DNS page.

• Status - The status of the Dynamic DNS service connection.

4. 2. 2. Internet

1. Visit http://mwlogin.net, and log in with the password you set for the router.

2. Go to Advanced > Network > Internet.

3. Set up the internet connection and click SAVE.

Dynamic IP

If your ISP provides the DHCP service, please select Dynamic IP, and the router will automatically get IP parameters from your ISP.

Click RENEW to renew the IP parameters from your ISP.

Page 18

Chapter 4 Congure the Router in Wireless Router Mode

Click RELEASE to release the IP parameters.

• MTU Size - The normal MTU (Maximum Transmission Unit) value for most Ethernet

networks is 1500 Bytes. It is not recommended that you change the default MTU size unless required by your ISP.

• Host Name - This option specifies the name of the router.

• Get IP with Unicast DHCP - A few ISPs’ DHCP servers do support the broadcast applications. If

you cannot get the IP address normally, you can choose this option (it is rarely required).

Static IP

If your ISP provides a static or fixed IP address, subnet mask, default gateway and DNS setting, please select Static IP.

• IP Address - Enter the IP address in dotted-decimal notation provided by your ISP.

• Subnet Mask - Enter the subnet mask in dotted-decimal notation provided by your ISP.

Normally 255.255.255.0 is used as the subnet mask.

• Default Gateway - Enter the gateway IP address in dotted-decimal notation provided by

your ISP.

• Primary/Secondary DNS - (Optional) Enter one or two DNS addresses in dotted-decimal

notation provided by your ISP.

• MTU Size - The normal MTU (Maximum Transmission Unit) value for most Ethernet

networks is 1500 bytes. It is not recommended that you change the default MTU size unless required by your ISP.

Page 19

Chapter 4 Congure the Router in Wireless Router Mode

PPPoE

If your ISP provides PPPoE connection, select PPPoE.

• Username/Password - Enter the user name and password provided by your ISP. These

fields are case-sensitive.

• Secondary Connection - It’s available only for PPPoE connection. If your ISP provides

an extra connection type, select Dynamic IP or Static IP to activate the secondary

connection.

Page 20

Chapter 4 Congure the Router in Wireless Router Mode

• MTU Size - The default MTU size is 1480 bytes. It is not recommended that you change

the default MTU size unless required by your ISP.

• Service Name - The service name should not be configured unless you are sure it is

necessary for your ISP. In most cases, leaving these fields blank will work.

• Access Concentrator Name - The access concentrator name should not be configured

unless you are sure it is necessary for your ISP. In most cases, leaving these fields blank will work.

• Detect Online Interval - The router will detect Access Concentrator online at every

interval. The default value is 10. You can input the value between 0 and 120. The value 0 means no detect.

• IP Address - The default setting is to get an IP address dynamically from your ISP. If your

ISP does not automatically assign IP addresses to the router, please select Use the Following IP Address and enter the IP address provided by your ISP in dotted-decimal

notation.

• DNS Address - The default setting is to get an IP address dynamically from your ISP. If

your ISP does not automatically assign DNS addresses to the router, please select Use the Following DNS Addresses and enter the IP address in dotted-decimal notation of your ISP’s primary DNS server. If a secondary DNS server address is available, enter it as well.

• Connection Mode - Select an appropriate connection mode that determines how to

connect to the internet.

• Auto - In this mode, the internet connection reconnects automatically any it gets

disconnected.

• On Demand - In this mode, the internet connection will be terminated automatically

after a specified inactivity period (Max Idle Time) and be re-established when you attempt to access the internet again.

• Time-based - In this mode, the internet connection is only established in a specific

timeframe. If this option is selected, enter the start time and end time. Both are in

HH:MM format.

• Manual - In this mode, the internet connection is controlled manually by clicking the

Connect/Disconnect button. This mode also supports the Max Idle Time function

as On Demand mode. Enter a maximum time (in minutes), the internet connection can be inactive before it is terminated into the Max Idle Time. The default value is 15 minutes. If you want the internet connection remains active all the time, enter 0

(zero).

Note:

Sometimes the connection cannot be terminated although you have specified the Max Idle Time because some applications

are visiting the internet continually in the background.

Page 21

Chapter 4 Congure the Router in Wireless Router Mode

L2TP

If your ISP provides L2TP connection, please select L2TP.

• Username/Password - Enter the username and password provided by your ISP. These

fields are case-sensitive.

• VPN Server IP/ Domain Name - Enter the VPN server’s IP address or domain name

provided by your ISP.

• MTU Size - The default MTU size is “1460” bytes, which is usually fine. It is not

recommended that you change the default MTU Size unless required by your ISP.

• Connection Mode

• Auto - In this mode, the internet connection reconnects automatically any it gets

disconnected.

Page 22

Chapter 4 Congure the Router in Wireless Router Mode

• On Demand - In this mode, the internet connection will be terminated automatically

after a specified inactivity period (Max Idle Time) and be re-established when you attempt to access the internet again.

• Manual - In this mode, the internet connection is controlled manually by clicking the

Connect/Disconnect button. This mode also supports the Max Idle Time function

(zero).

Note:

Sometimes the connection cannot be terminated although you have specified the Max Idle Time because some applications

are visiting the internet continually in the background.

PPTP

If your ISP provides PPTP connection, please select PPTP.

Page 23

Chapter 4 Congure the Router in Wireless Router Mode

• Username/Password - Enter the username and password provided by your ISP. These

fields are case-sensitive.

• VPN Server IP/ Domain Name - Enter the VPN server’s IP address or domain name

provided by your ISP.

• MTU Size - The default MTU size is “1420” bytes, which is usually fine. It is not

recommended that you change the default MTU Size unless required by your ISP.

• Connection Mode

• Auto - In this mode, the internet connection reconnects automatically any it gets

disconnected.

• On Demand - In this mode, the internet connection will be terminated automatically

after a specified inactivity period (Max Idle Time) and be re-established when you attempt to access the internet again.

• Manual - In this mode, the internet connection is controlled manually by clicking the

Connect/Disconnect button. This mode also supports the Max Idle Time function

(zero).

Note:

Sometimes the connection cannot be terminated although you have specified the Max Idle Time because some applications

are visiting the internet continually in the background.

4. 2. 3. MAC Clone

1. Visit http://mwlogin.net, and log in with the password you set for the router.

2. Go to Advanced > Network > Internet and locate the MAC Clone section.

3. Configure Router MAC Address and click SAVE.

• Use Default MAC Address - Do not change the default MAC address of your router

in case the ISP does not bind the assigned IP address to the MAC address.

Page 24

Chapter 4 Congure the Router in Wireless Router Mode

• Use Current MAC Address - Select to copy the current MAC address of the

computer that is connected to the router, in case the ISP binds the assigned IP address to the MAC address.

• Use Custom MAC Address - Select if your ISP requires you to register the MAC

address and enter the correct MAC address in this field, in case the ISP binds the assigned IP address to the specific MAC address.

Note:

• You can only use the MAC Address Clone function for PCs on the LAN.

• If you have changed the WAN MAC address when the WAN connection is PPPoE, it will not take effect until the connection is

re-established.

4. 2. 4. LAN

1. Visit http://mwlogin.net, and log in with the password you set for the router.

2. Go to Advanced > Network > LAN.

3. Configure the IP parameters of the LAN and click SAVE.

• MAC Address - The physical address of the LAN ports. The value can not be changed.

• IP Address - Enter the IP address in dotted-decimal notation of your router (the default

one is 192.168.1.1).

• Subnet Mask - An address code that determines the size of the network. Normally

255.255.255.0 is used as the subnet mask.

Note:

• If you have changed the IP address, you must use the new IP address to log in.

• If the new IP address you set is not in the same subnet as the old one, the IP address pool in the DHCP Server will be

configured automatically, but the Virtual Server and DMZ Host will not take effect until they are re-configured.

4. 2. 5. IPTV/VLAN

1. Visit

2. Go to Advanced > Network > IPTV/VLAN.

3. Configure IPTV/VLAN settings if you want to enjoy IPTV or VoIP service, or if your ISP

http://mwlogin.net, and log in with the password you set for the router.

requires VLAN tags.

Page 25

Chapter 4 Congure the Router in Wireless Router Mode

• IPTV/VLAN - Select to enable the IPTV feature.

• Mode - Select the appropriate mode according to your ISP.

• LAN 1/2/3 - Assign your LAN port to whether function as the internet supplier or as the

IPTV supplier.

4. 2. 6. DHCP Server

By default, the DHCP (Dynamic Host Configuration Protocol) Server is enabled and the router acts as a DHCP server; it dynamically assigns TCP/IP parameters to client devices from the IP Address Pool. You can change the settings of DHCP Server if necessary, and you can reserve LAN IP addresses for specified client devices.

• To specify the IP address that the router assigns:

1. Visit http://mwlogin.net, and log in with the password you set for the router.

2. Go to Advanced > Network > DHCP Server and locate the DHCP Server section.

1. Tick the Enable checkbox.

2. Enter the starting and ending IP addresses in the IP Address Pool.

3. Enter other parameters if the ISP offers. The Default Gateway is automatically filled in

and is the same as the LAN IP address of the router.

Page 26

Chapter 4 Congure the Router in Wireless Router Mode

4. Click SAVE.

Note:

To use the DHCP server function of the router, you must configure all computers on the LAN as Obtain an IP Address

automatically.

• To reserve an IP address for a specified client device:

1. Visit http://mwlogin.net, and log in with the password you set for the router.

2. Go to Advanced > Network > DHCP Server and locate the Address Reservation

section.

3. Click Add in the Address Reservation section.

4. Click VIEW CONNECTED DEVICES and select the you device you want to reserve an IP

for. Then the MAC and IP Address will be automatically filled in. You can also enter the MAC and IP address of the client device.

• To check the DHCP client list:

1. Visit http://mwlogin.net, and log in with the password you set for the router.

2. Go to Advanced > Network > DHCP Server and locate the DHCP Client List section. You

can see the device information of the list.

3. Click Refresh to see the current attached devices.

Page 27

Chapter 4 Congure the Router in Wireless Router Mode

4. 2. 7. Dynamic DNS

The router offers the DDNS (Dynamic Domain Name System) feature, which allows the hosting of a website, FTP server, or e-mail server with a fixed domain name (named by yourself) and a dynamic IP address. Thus your friends can connect to your server by entering your domain name no matter what your IP address is. Before using this feature, you need to sign up for DDNS service providers such as www.comexe.cn, www.dyndns.org, or www.noip.com. The Dynamic DNS client service provider will give you a password or key.

1. Visit http://mwlogin.net, and log in with the username and password you set for the

router.

2. Go to Advanced > Network > Dynamic DNS.

3. Select the DDNS Service Provider: NO-IP or DynDNS. If you don’t have a DDNS account,

you have to register first by clicking Register Now.

4. Enter the Username for your DDNS account.

5. Enter the Password for your DDNS account.

6. Enter the Domain Name you received from dynamic DNS service provider here.

7. If your service provider is NO-IP, select WAN IP binding to ensure that the domain name

is bound to the WAN IP of this router.

Page 28

Chapter 4 Congure the Router in Wireless Router Mode

8. Click LOGIN AND SAVE.

4. 2. 8. Static Routing

Static Routing is a form of routing that is configured manually by a network administrator or a user by adding entries into a routing table. The manually-configured routing information guides the router in forwarding data packets to the specific destination.

I want to:

Visit multiple networks and servers at the same time.

For example, in a small office, my PC can surf the internet through Router A, but I also want to visit my company’s network. Now I have a switch and Router B. I connect the devices as shown in the following figure so that the physical connection between my PC and my company’s server is established. To surf the internet and visit my company’s network at the same time, I need to configure the static routing.

Router A

LAN: 192.168.1.1

Switch

192.168.1.100

Router B

LAN: 192.168.1.2

Company’s server

WAN: 172.30.30.100

172.30.30.1

How can I do that?

1. Change the routers’ LAN IP addresses to two different IP addresses on the same subnet.

Disable Router B’s DHCP function.

2. Visit http://mwlogin.net, and log in with the password you set for Router A.

3. Go to Advanced > Network > Routing and locate the Static Routing section.

4. Click Add and finish the settings according to the following explanations:

Page 29

Chapter 4 Congure the Router in Wireless Router Mode

• Network Destination - The destination IP address that you want to assign to a

static route. This IP address cannot be on the same subnet with the WAN IP or LAN IP of Router A. In the example, the IP address of the company network is the destination IP address, so here enter 172.30.30.1.

• Subnet Mask - The Subnet Mask determines which portion of an IP address is the

network portion, and which portion is the host portion.

• Default Gateway - The IP address of the gateway device to which the data packets

will be sent. This IP address must be on the same subnet with the router’s IP which sends out data. In the example, the data packets will be sent to the LAN port of Router B and then to the Server, so the default gateway should be 192.168.1.2.

• Interface - Determined by the port (WAN/LAN) that sends out data packets. In the

example, the data are sent to the gateway through the LAN port of Router A, so LAN should be selected.

• Description - Enter a description for this static routing entry.

5. Click SAVE.

6. Check the Routing Table below. If you can find the entry you’ve set, the static routing is

set successfully.

4. 3. Wireless

4. 3. 1. Wireless Settings

1. Visit http://mwlogin.net, and log in with the password you set for the router.

2. Go to Advanced > Wireless > Wireless Settings.

3. Configure the wireless settings for the wireless network and click SAVE.

Page 30

Chapter 4 Congure the Router in Wireless Router Mode

• 2.4GHz - Select this checkbox to enable the 2.4GHz wireless network.

• Network Name (SSID) - Enter a value of up to 32 characters. The same Name (SSID) must

be assigned to all wireless devices in your network.

• Hide SSID - Select this checkbox if you want to hide the 2.4GHz network name (SSID)

from the Wi-Fi network list. In this case, you need to manually join the network.

• Security - Select an option from the Security drop-down list.

• None - No security. It is highly recommend you enable the wireless security to

protect your wireless network from unauthorized access.

• WPA-PSK/WPA2-Personal - It’s the WPA/WPA2 authentication type based on pre-

shared passphrase. It’s also the recommended security type.

• WPA2/WPA3-Personal - If you are having WPA3-supported clients, select this

option to enjoy stronger protections than WPA/WPA2-Personal.

• WPA /WPA2-Enterprise - It’s based on Radius Server.

• Version - Keep default version value.

• Encryption - Select Auto, TKIP or AES. We recommend you keep the default settings.

• Transmit Power - Select High, Middle or Low to specify the data transmit power. The

default and recommended setting is High.

• Channel Width - Select a channel width (bandwidth) for the wireless network.

• Channel - Select an operating channel for the wireless network. It is recommended to

leave the channel to Auto, if you are not experiencing the intermittent wireless connection issue.

• Mode - You can choose the appropriate “Mixed” mode.

Page 31

Chapter 4 Congure the Router in Wireless Router Mode

4. 3. 2. Guest Network

Guest Network allows you to provide Wi-Fi access for guests without disclosing your host network. When you have guests in your house, apartment, or workplace, you can create a guest network for them. In addition, you can customize guest network settings to ensure network security and privacy.

• Create a Guest Network

1. Visit http://mwlogin.net, and log in with the password you set for the router.

2. Go to Wireless or Advanced > Wireless > Guest Network.

3. Enable the Guest Network function.

4. Create a network name for your guest network.

5. Select the Security type and create the Password of the guest network.

6. Click SAVE. Now you guests can access your guest network using the SSID and

password you set!

• Customize Guest Network Options

1. Visit http://mwlogin.net, and log in with the password you set for the router.

2. Go to Advanced > Wireless > Guest Network. Locate the Guest Permissions section.

3. Customize guest network options according to your needs.

• Allow guests to see each other

Tick this checkbox if you want to allow the wireless clients on your guest network to communicate with each other via methods such as network neighbors and Ping.

• Allow guests to access my local network

Page 32

Chapter 4 Congure the Router in Wireless Router Mode

Tick this checkbox if you want to allow the wireless clients on your guest network to communicate with the devices connected to your router’s LAN ports or main network via methods such as network neighbors and Ping.

4. Click SAVE. Now you can ensure network security and privacy!

4. 3. 3. Wireless Schedule

The wireless function can be automatically off at a specific time when you do not need the wireless function.

1. Visit http://mwlogin.net, and log in with the password you set for the router.

2. Go to Advanced > Wireless > Wireless Schedule.

3. Enable the Wireless Schedule function.

4. Click Add to specify a wireless off period during which you need the wireless off

automatically, and click SAVE.

Note:

• The effective wireless schedule is based on the time of the router. You can go to Advanced > System > Time to modify the

time.

• The wireless network will be automatically turned on after the time period you set.

Page 33

Chapter 4 Congure the Router in Wireless Router Mode

4. 3. 4. WPS

WPS (Wi-Fi Protected Setup) can help you to quickly and securely connect to a network. This section will guide you to add a new wireless device to your router’s network quickly via

WPS.

Note:

The WPS function cannot be configured if the wireless function of the router is disabled. Please make sure the wireless

function is enabled before configuration.

1. Visit http://mwlogin.net, and log in with the password you set for the router.

2. Go to Advanced > Wireless > WPS.

3. Follow one of the following methods to connect your client device to the router’s Wi-Fi

network.

Method 1: Using a PIN

• Connects via the Client’s PIN

1. Keep the WPS Status as Enabled and select Client’s PIN.

2. Enter the PIN of your device and click CONNECT. Then your device will get connected to

the router.

• Connects via the Router’s PIN

1. Keep the WPS Status as Enabled and select Router’s PIN.

Page 34

Chapter 4 Congure the Router in Wireless Router Mode

2. Enter the router’s PIN on your personal device. You can also generate a new one.

Note:

PIN (Personal Identification Number) is an eight-character identification number preset to each router. WPS supported devices

can connect to your router with the PIN.

Method 2: Using the WPS Button on the Web Screen

Click Start on the screen. Within two minutes, enable WPS on your personal device. A Devic e- (X X-X X-XX-X X-X X-XX) Connected message should appear on the screen,

indicating successful WPS connection.

Note:

XX-XX-XX-XX-XX-XX is the MAC address of your device.

Method 3: Using the WPS Button on the Router

Press the router’s WPS button. Within two minutes, enable WPS on your personal device.

Page 35

Chapter 4 Congure the Router in Wireless Router Mode

4. 3. 5. Additional Settings

1. Visit http://mwlogin.net, and log in with the password you set for the router.

2. Go to Advanced > Wireless > Additional Settings.

3. Configure the advanced settings of your wireless network and click Save.

Note:

If you are not familiar with the setting items on this page, it’s strongly recommended to keep the provided default values;

otherwise it may result in lower wireless network performance.

• WMM - WMM function can guarantee the packets with high-priority messages being

transmitted preferentially.

• AP Isolation - This function isolates all connected wireless stations so that wireless

stations cannot access each other through WLAN.

• Airtime Fairness - This function can improve the overall network performance by

sacrificing a little bit of network time on your slow devices.

• Beacon Interval - Enter a value between 40-1000 milliseconds for Beacon Interval here.

Beacon Interval value determines the time interval of the beacons. The beacons are the packets sent by the router to synchronize a wireless network. The default value is 100.

• RTS Threshold - Here you can specify the RTS (Request to Send) Threshold. If the packet

is larger than the specified RTS Threshold size, the router will send RTS frames to a particular receiving station and negotiate the sending of a data frame. The default value is

2346.

• DTIM Interval - This value determines the interval of the Delivery Traffic Indication

Message (DTIM). A DTIM field is a countdown field informing clients of the next window for listening to broadcast and multicast messages. When the router has buffered broadcast or multicast messages for associated clients, it sends the next DTIM with a DTIM Interval value. You can specify the value between 1-255 Beacon Intervals. The default value is 1, which indicates the DTIM Interval is the same as Beacon Interval.

Page 36

Chapter 4 Congure the Router in Wireless Router Mode

• Group Key Update Period - Enter a number of seconds (minimum 30) to control the time

interval for the encryption key automatic renewal. The default value is 0, meaning no key renewal.

4. 4. NAT Forwarding

The router’s NAT (Network Address Translation) feature makes the devices on the LAN use the same public IP address to communicate on the internet, which protects the local network by hiding IP addresses of the devices. However, it also brings about the problem that external hosts cannot initiatively communicate with the specified devices in the local network.

With the forwarding feature, the router can traverse the isolation of NAT so that clients on the internet can reach devices on the LAN and realize some specific functions.

The Mercusys router includes four forwarding rules. If two or more rules are set, the priority of implementation from high to low is Port Forwarding, Port Triggering, UPNP and DMZ.

4. 4. 1. Port Forwarding

When you build up a server in the local network and want to share it on the internet, Port Forwarding can realize the service and provide it to internet users. At the same time Port Forwarding can keep the local network safe as other services are still invisible from the

internet.

Port Forwarding can be used to set up public services in your local network, such as HTTP, FTP, DNS, POP3/SMTP and Telnet. Different service uses different service port. Port 80 is used in HTTP service, port 21 in FTP service, port 25 in SMTP service and port 110 in POP3 service. Please verify the service port number before the configuration.

I want to:

Share my personal website I’ve built in local network with my friends through the internet.

For example, the personal website has been built in my home PC (192.168.1.100). I hope that my friends on the internet can visit my website in some way. My PC is connected to the router with the WAN IP address 218.18.232.154.

Personal Website

Router

Home

LAN

WAN: 218.18.232.154

Page 37

Chapter 4 Congure the Router in Wireless Router Mode

1. Set your PC to a static IP address, for example 192.168.1.100.

7. Visit http://mwlogin.net, and log in with the password you set for the router.

8. Go to Advanced > NAT Forwarding > Port Forwarding.

9. Click Add.

2. Click VIEW COMMON SERVICES and select HTTP. The External Port, Internal Port and

Protocol will be automatically filled in.

10. Click VIEW CONNECTED DEVICES and select your home PC. The Device IP

Address will be automatically filled in. Or enter the PC’s IP address 192.168.1.100 manually in the Device IP Address field.

11. Click SAVE.

Note:

• It is recommended to keep the default settings of Internal Port and Protocol if you are not clear about which

port and protocol to use.

• If the service you want to use is not in the Common Services list, you can enter the corresponding

parameters manually. You should verify the port number that the service needs.

• You can add multiple virtual server rules if you want to provide several services in a router. Please note that

the External Port should not be overlapped.

Done!

Users on the internet can enter http:// WAN IP (in this example: http:// 218.18.232.154) to visit your personal website.

Note:

• If you have changed the default External Port, you should use http:// WAN IP: External Port to visit the

website.

• The WAN IP should be a public IP address. For the WAN IP is assigned dynamically by the ISP, it is

recommended to apply and register a domain name for the WAN referring to Dynamic DNS. Then users on the internet can use http:// domain name to visit the website.

Page 38

Chapter 4 Congure the Router in Wireless Router Mode

4. 4. 2. Port Triggering

Port triggering can specify a triggering port and its corresponding external ports. When a host in the local network initiates a connection to the triggering port, all the external ports will be opened for subsequent connections. The router can record the IP address of the host. When the data from the internet return to the external ports, the router can forward them to the corresponding host. Port triggering is mainly applied to online games, VoIPs, video players and common applications including MSN Gaming Zone, Dialpad, Quick Time 4 players and more.

Follow the steps below to configure the port triggering rules:

1. Visit http://mwlogin.net, and log in with the password you set for the router.

2. Go to Advanced > NAT Forwarding > Port Triggering.

3. Click Add.

4. Click VIEW COMMON SERVICES, and select the desired application. The Triggering Port,

Triggering Protocol and External Port will be automatically filled in. The following picture takes application MSN Gaming Zone as an example.

5. Click SAVE.

Note:

• You can add multiple port triggering rules as needed.

• The triggering ports can not be overlapped.

• If the application you need is not listed in the Common Services list, please enter the parameters manually. You should verify

the external ports the application uses first and enter them in External Ports field. You can input at most 5 groups of ports

(or port sections). Every group of ports must be set apart with “,”. For example, 2000-2038, 2050-2051, 2085, 3010-3030.

Page 39

Chapter 4 Congure the Router in Wireless Router Mode

4. 4. 3. UPnP

The UPnP (Universal Plug and Play) protocol allows the applications or host devices to automatically find the front-end NAT device and send request to it to open the corresponding ports. With UPnP enabled, the applications or host devices on the local network and the internet can freely communicate with each other realizing the seamless connection of the network. You may need to enable the UPnP if you want to use applications for multiplayer gaming, peer-to-peer connections, real-time communication (such as VoIP or telephone conference) or remote assistance, etc.

Tips:

• UPnP is enabled by default in this router.

• Only the application supporting UPnP protocol can use this feature.

• UPnP feature needs the support of operating system (e.g. Windows Vista/ Windows 7/ Windows 8, etc. Some of operating

system need to install the UPnP components).

For example, when you connect your Xbox to the router which is connected to the internet to play online games, UPnP will send request to the router to open the corresponding ports allowing the following data penetrating the NAT to transmit. Therefore, you can play Xbox online games without a hitch.

LAN

WAN

RouterXbox

If necessary, you can follow the steps to change the status of UPnP.

1. Visit http://mwlogin.net, and log in with the password you set for the router.

2. Go to Advanced > NAT Forwarding > UPnP and toggle on or off according to your needs.

Page 40

Chapter 4 Congure the Router in Wireless Router Mode

4. 4. 4. DMZ

When a PC is set to be a DMZ (Demilitarized Zone) host in the local network, it is totally exposed to the internet, which can realize the unlimited bidirectional communication between internal hosts and external hosts. The DMZ host becomes a virtual server with all ports opened. When you are not clear about which ports to open in some special applications, such as IP camera and database software, you can set the PC to be a DMZ host.

Note:

DMZ is more applicable in the situation that users are not clear about which ports to open. When it is enabled, the DMZ host is

totally exposed to the internet, which may bring some potential safety hazards. If DMZ is not in use, please disable it in time.

I want to:

Make the home PC join the internet online game without port restriction.

For example, due to some port restriction, when playing the online games, you can log in normally but cannot join a team with other players. To solve this problem, set your PC as a DMZ host with all ports opened.

How can I do that?

1. Assign a static IP address to your PC, for example 192.168.1.100.

2. Visit http://mwlogin.net, and log in with the password you set for the router.

3. Go to Advanced > NAT Forwarding > DMZ and select Enable DMZ.

4. Click VIEW CONNECTED DEVICES and select your PC. The DMZ Host IP

Address will be automatically filled in. Or enter the PC’s IP address 192.168.1.100 manually in the DMZ Host IP Address field.

Page 41

Chapter 4 Congure the Router in Wireless Router Mode

3. Click SAVE.

Done!

You’ve set your PC to a DMZ host and now you can make a team to game with other players.

4. 5. Parental Controls

Parental Controls allows you to set up unique restrictions on internet access for each member of your family. You can block inappropriate content, set daily limits for the total time spent online and restrict internet access to certain times of the day.

I want to:

Block access to inappropriate online content for my child’s devices, restrict internet access to 2 hours every day and block internet access during bed time (10 PM to 7 AM) on weekdays.

How can I do that?

1. Visit http://mwlogin.net, and log in with the password you set for the router.

2. Go to Advanced > Parental Controls.

3. Click Add to create a profile for a family member.

4. Add basic profile information.

Page 42

Chapter 4 Congure the Router in Wireless Router Mode

1 ) Enter a Name for the profile to make it easier to identify.

2 ) Under Devices, click

3 ) Select the devices that belong to this family member. Access restrictions will be

applied to these devices. Click ADD when finished.

Note: Only devices that have previously been connected to your router’s network are listed here. If you are

unable to find the device you want to add, connect it to your network and then try again.

4 ) Click NEXT.

5. Block content for this profile.

1 ) Enter the key word of the website that you want to block. Click if want to block

multiple websites.

2 ) Click NEXT.

5. Set time restrictions on internet access.

Page 43

Chapter 4 Congure the Router in Wireless Router Mode

1 ) Enable Time Limits on Monday to Friday and Saturday & Sunday then set the

allowed online time to 2 hours each day.

2 ) Enable Bed Time on School Nights (Sun to Thur) and use the up/down arrows or

enter times in the fields. Devices under this profile will be unable to access the internet during this time period.

3 ) Click SAVE.

Note: The effective time limits are based on the time of the router. You can go to Advanced > System > Time to modify

the time.

Done!

The amount of time your child spends online is controlled and inappropriate content is blocked on their devices.

4. 6. QoS

QoS (Quality of Service) is designed to ensure the efficient operation of the network when come across network overload or congestion. Devices set as high priority will be allocated more bandwidth and so continue to run smoothly even when there are many devices connected to the network.

Page 44

Chapter 4 Congure the Router in Wireless Router Mode

I want to:

Ensure a fast connection of my computer while I play online games for the next 2 hours.

How can I do that

1. Visit http://mwlogin.net, and log in with the password you set for the router.

2. Go to Advanced > QoS.

3. Tick the Enable checkbox of QoS.

4. Enter the maximum upload and download bandwidths provided by your internet service

provider, and then click SAVE. 1Mbps equals to 1,000Kbps.

5. Find your computer in the Device Priority section and toggle on Priority. Select 4 hours

from the drop-down list of Timing. Your computer will be prioritized for the next 4 hours.

Done!

You can now enjoy playing games without lag on your computer for the next 4 hours.

4. 7. Security

This function allows you to protect your home network from cyber attacks and unauthorized users by implementing these network security functions.

4. 7. 1. Firewall

The SPI (Stateful Packet Inspection) Firewall protects the router from cyber attacks and validate the traffic that is passing through the router based on the protocol. This function is enabled by default.

Page 45

Chapter 4 Congure the Router in Wireless Router Mode

1. Visit http://mwlogin.net, and log in with the password you set for the router.

2. Go to Advanced > Security > Firewall, and configure the parameters as you need. It’s

recommended to keep the default settings.

4. 7. 2. Access Control

Access Control is used to block or allow specific client devices to access your network (via wired or wireless) based on a list of blocked devices (Blacklist) or a list of allowed devices (Whitelist).

I want to:

Block or allow specific client devices to access my network (via wired or wireless).

How can I do that?

1. Visit http://mwlogin.net, and log in with the password you set for the router.

2. Go to Advanced > Security > Access Control.

3. Select the access mode to either block (recommended) or allow the device(s) in the list.

To block specific device(s):

1 ) Select Blacklist and click SAVE.

2 ) Click Add and select devices you want to be blocked. You can see the devices have

been added to the blacklist.

Page 46

To allow specific device(s):

1 ) Select Whitelist and click SAVE.

Chapter 4 Congure the Router in Wireless Router Mode

2 ) Add devices to the whitelist.

• Add connected devices

Click Select From Device List and select the devices you want to be allowed.

• Add unconnected devices

Page 47

Chapter 4 Congure the Router in Wireless Router Mode

Click Add Manually and enter the Device Name and MAC Address of the device you want to be allowed.

Done!

Now you can block or allow specific client devices to access your network (via wired or wireless) using the Blacklist or Whitelist.

4. 7. 3. IP & MAC Binding

IP & MAC Binding, namely, ARP (Address Resolution Protocol) Binding, is used to bind network device’s IP address to its MAC address. This will prevent ARP Spoofing and other ARP attacks by denying network access to a device with matching IP address in the Binding list, but unrecognized MAC address.

I want to:

Prevent ARP spoofing and ARP attacks.

How can I do that?

1. Visit http://mwlogin.net, and log in with the password you set for the router.

2. Go to Advanced > Security > IP & MAC Binding.

3. Enable IP & MAC Binding and click SAVE.

4. Bind your device(s) according to your need.

To bind the connected device(s):

Page 48

Chapter 4 Congure the Router in Wireless Router Mode

Locate the ARP List section and enable Bind to bind the IP and MAC addresses of a specific device.

To add a binding entry:

1 ) Click Add in the Binding List section.

2 ) Click VIEW CONNECTED DEVICES and select the device you want to bind. Or enter

the MAC Address and IP Address that you want to bind.

3 ) Click ADD.

4. 7. 4. ALG

You can view ALG (Application Layer Gateway) settings at Advanced > Security> ALG. It is recommended to keep them as default.

4. 8. VPN Server

The VPN (Virtual Private Networking) Server allows you to access your home network in a secured way through internet when you are out of home. The router offers two ways to setup VPN connection: OpenVPN and PPTP (Point to Point Tunneling Protocol) VPN.

Page 49

Chapter 4 Congure the Router in Wireless Router Mode

4. 8. 1. OpenVPN

OpenVPN is somewhat complex but with greater security and more stable. It is suitable for restricted environment, such as campus network and company intranet In the OpenVPN connection, the home network can act as a server, and the remote device can access the server through the router which acts as an OpenVPN Server gateway.

To use the VPN feature, you should enable OpenVPN Server on your router, and install and run VPN client software on the remote device. Please follow the steps below to set up an

OpenVPN connection.

Step1. Set up OpenVPN Server on Your Router

1. Visit http://mwlogin.net, and log in with the password you set for the router.

Note:

• Before you enable VPN Server, we recommend you configure Dynamic DNS Service (recommended) or assign a static IP

address for router’s WAN port and synchronize your System Time with internet.

• The first time you configure the OpenVPN Server, you may need to Generate a certificate before you enable the VPN Server.

2. Go to Advanced > VPN Server > OpenVPN, and enable VPN Server.

3. Select the Service Type (communication protocol) for OpenVPN Server: UDP, TCP.

4. Enter a Service Port to which a VPN device connects, and the port number should be

between 1024 and 65535.

5. In the VPN Subnet and Netmask fields, enter the range of IP addresses that can be leased

to the device by the OpenVPN server.

6. Select your Client Access type. Select Home Network Only if you only want the remote

device to access your home network; select Internet and Home Network if you also want the remote device to access internet through the VPN Server.

7. Click SAVE then click GENERATE to get a new certificate.

Page 50

Chapter 4 Congure the Router in Wireless Router Mode

Note:

If you have already generated one, please skip this step, or click GENERATE to update the certificate.

8. Click EXPORT to save the OpenVPN configuration file which will be used by the remote

device to access your router.

Step 2. Configure OpenVPN Connection on Your Remote Device

1. Visit http://openvpn.net/index.php/download/community-downloads.html to download

the OpenVPN software, and install it on your device where you want to run the OpenVPN client utility.

Note:

You need to install the OpenVPN client utility on each device that you plan to apply the VPN function to access your router.

Mobile devices should download a third-party app from Google Play or Apple App Store.

2. After the installation, copy the file exported from your router to the OpenVPN client utility’s

“config” folder (for example, C:\Program Files\OpenVPN\config on Windows). The path depends on where the OpenVPN client utility is installed.

3. Run the OpenVPN client utility and connect it to OpenVPN Server.

4. 8. 2. PPTP VPN

PPTP VPN is more easily used and its speed is faster, it’s compatible with most operating systems and also supports mobile devices. Its security is poor and your packets may be cracked easily, and PPTP VPN connection may be prevented by some ISP.

To use the VPN feature, you should enable PPTP VPN Server on your router, and configure the PPTP connection on the remote device. Please follow the steps below to set up a PPTP

VPN connection.

Step 1. Set up PPTP VPN Server on Your Router

1. Visit http://mwlogin.net, and log in with the password you set for the router.

2. Go to Advanced > VPN Server > PPTP, and enable PPTP.

Note:

Before you enable VPN Server, we recommend you configure Dynamic DNS Service (recommended) or assign a static IP address

for router’s WAN port and synchronize your System Time with internet.

Page 51

Chapter 4 Congure the Router in Wireless Router Mode

3. In the Client IP Address filed, enter the range of IP addresses (up to 10) that can be leased

to the devices by the PPTP VPN server.

4. Set the PPTP connection permission according to your needs.

• Select Allow Samba (Network Place) access to allow your VPN device to access your

local Samba server.

• Select Allow NetBIOS passthrough to allow your VPN device to access your Samba

server using NetBIOS name.

• Select Allow Unencrypted connections to allow unencrypted connections to your

VPN server.

5. Click SAVE then configure the PPTP VPN connection account for the remote device, you

can create up to 16 accounts.

1 ) Click Add. 2 ) Enter the Username and Password to authenticate devices to the PPTP VPN Server. 3 ) Click ADD to save the information.

Step 2. Configure PPTP VPN Connection on Your Remote Device

Page 52

Chapter 4 Congure the Router in Wireless Router Mode

The remote device can use the Windows built-in PPTP software or a third-party PPTP software to connect to PPTP Server. Here we use the Windows built-in PPTP software as an example.

1. Go to Start > Control Panel > Network and Internet > Network and Sharing Center.

2. Select Set up a new connection or network.

3. Select Connect to a workplace and click Next.

4. Select Use my Internet connection (VPN).

Page 53

Chapter 4 Congure the Router in Wireless Router Mode

5. Enter the internet IP address of the router (for example: 218.18.1.73) in the Internet address

field. Click Next.

6. Enter the User name and Password you have set for the PPTP VPN server on your router,

and click Connect.

Page 54

Chapter 4 Congure the Router in Wireless Router Mode

7. The PPTP VPN connection is created and ready to use.

4. 9. IPv6

This function allows you to enable IPv6 function and set up the parameters of the router’s Wide Area Network (WAN) and Local Area Network (LAN).

1. Visit http://mwlogin.net, and log in with the password you set for the router.

Page 55

Chapter 4 Congure the Router in Wireless Router Mode

2. Go to Advanced > IPv6, and you can view the current IPv6 status information of the

router.

3. Enable IPv6 and select the mode: Router or Pass-Through (Bridge).

• If you select Router:

Fill in WAN and LAN information as required by different connection types.

• Normal: The default connection type.

1 ) Configure the WAN settings.

2 ) Configure the LAN settings. Fill in Address Prefix provided by your ISP.

3 ) Click SAVE.

Page 56

Chapter 4 Congure the Router in Wireless Router Mode

• PPPoE: Select this type if your ISP uses PPPoEv6, and provides a username and

password.

1 ) Configure the WAN settings.

2 ) Configure the LAN settings. Fill in Address Prefix provided by your ISP.

• Tunnel 6to4: Select this type if your ISP uses 6 to 4 deployment fort assigning

address.

1 ) Configure the WAN settings.

Page 57

2 ) Configure the LAN settings.

• If you select Pass-Through (Bridge):

Click SAVE. No configuration is required.

Chapter 4 Congure the Router in Wireless Router Mode

4. 10. System

4. 10. 1. Firmware Upgrade

Mercusys is dedicated to improving and richening the product features, giving users a better network experience. We will release the latest firmware at Mercusys official website www.mercusys.com. You can download the latest firmware file from the Support page of our website and upgrade the firmware to the latest version.

1. Download the latest firmware file for the router from our website www.mercusys.com.

2. Visit http://mwlogin.net, and log in with the password you set for the router.

3. Go to Advanced > System > Firmware Upgrade.

4. Click BROWSE to locate the downloaded firmware file, and click UPGRADE.

Page 58

Chapter 4 Congure the Router in Wireless Router Mode

4. 10. 2. Backup & Restore

The configuration settings are stored as a configuration file in the router. You can backup the configuration file in your computer for future use and restore the router to the previous settings from the backup file when needed.

1. Visit http://mwlogin.net, and log in with the password you set for the router.

2. Go to Advanced > System > Backup & Restore.

To backup configuration settings:

Click BACK UP to save a copy of the current settings in your local computer. A “.bin“ file of the current settings will be stored in your computer.

To restore configuration settings:

1. Click BROWSE to locate the backup configuration file stored in your computer, and click

RESTORE.

2. Wait a few minutes for the restoring and rebooting.

To reset the router to factory default settings:

Page 59

Chapter 4 Congure the Router in Wireless Router Mode

1. Click FACTORY RESTORE to reset the router.

2. Wait a few minutes for the restoring and rebooting.

Note:

• During the resetting process, do not turn off or reset the router.

• We strongly recommend you back up the current configuration settings before resetting the router.

4. 10. 3. Change Password

1. Visit http://mwlogin.net, and log in with the password you set for the router.

2. Go to Advanced > System > Administration, and focus on the Change Password section.

3. Enter the old password, then a new password twice (both case-sensitive). Click SAVE.

4. Use the new password for future logins.

4. 10. 4. Local Management

1. Visit http://mwlogin.net, and log in with the password you set for the router.

2. Go to Advanced > System > Administration, and focus on the Local Management

section.

• Allow all LAN connected devices to manage the router:

Select All Devices for Local Managers.

Page 60

Chapter 4 Congure the Router in Wireless Router Mode

• Allow specific devices to manage the router:

1. Select Specified Devices for Local Managers and click SAVE.

2. Click Add Device.

3. Click VIEW CONNECTED DEVICES and select the device to manage the router from the

Connected Devices list, or enter the MAC address of the device manually.

4. Specify a Description for this entry.

5. Click SAVE.

4. 10. 5. Remote Management

1. Visit http://mwlogin.net, and log in with the password you set for the router.

2. Go to Advanced > System > Administration, and focus on the Remote Management

section.

• Forbid all devices to manage the router remotely:

Do not tick the Enable checkbox of Remote Management.

Page 61

Chapter 4 Congure the Router in Wireless Router Mode

• Allow all devices to manage the router remotely:

1. Tick the Enable checkbox of Remote Management.

2. Keep the HTTP port as default setting (recommended) or enter a value between 1024 and

65535.

3. Select All Devices for Remote Managers.

4. Click SAVE.

Devices on the internet can log in to http://Router’s WAN IP address:port number (such as http://113.116.60.229:1024) to manage the router.

Tips:

• You can find the WAN IP address of the router on Network Map > Internet.

• The router’s WAN IP is usually a dynamic IP. Please refer to Dynamic DNS if you want to log in to the router through a

domain name.

• Allow a specific device to manage the router remotely:

Page 62

Chapter 4 Congure the Router in Wireless Router Mode

1. Tick the Enable checkbox of Remote Management.

2. Keep the HTTP port as default setting (recommended) or enter a value between 1024 and

65535.

3. Select Specified Device for Remote Managers.

4. In the Only this IP Address field, enter the IP address of the remote device to manage the

router.

5. Click SAVE.

Devices using this WAN IP can manage the router by logging in to http://Router’s WAN IP:port number (such as http://113.116.60.229:1024).

Tips: The router’s WAN IP is usually a dynamic IP. Please refer to Dynamic DNS if you want to log in to the router through a

domain name.

4. 10. 6. System Log

1. Visit http://mwlogin.net, and log in with the password you set for the router.

2. Go to Advanced > System > System Log, and you can view the logs of the router.

Page 63

Chapter 4 Congure the Router in Wireless Router Mode

3. Click SAVE TO LOCAL to save the system logs to a local disk.

4. 10. 7. Diagnostics

Diagnostic is used to test the connectivity between the router and the host or other network devices.

1. Visit http://mwlogin.net, and log in with the password you set for the router.

2. Go to Advanced > System > Diagnostics.

3. Enter the information:

1 ) Choose Ping or Tracert as the diagnostic tool to test the connectivity.

• Ping is used to test the connectivity between the router and the tested host, and

measure the round-trip time.

Page 64

Chapter 4 Congure the Router in Wireless Router Mode

• Tracert is used to display the route (path) your router has passed to reach the

tested host, and measure transit delays of packets across an Internet Protocol network.

2 ) Enter the IP Address or Domain Name of the tested host.

3 ) Modify the Ping Count number and the Ping Packet Size. It’s recommended to

keep the default value.

4 ) If you have chosen Tracert, you can modify the Traceroute Max TTL. It’s

recommended to keep the default value.

4. Click START to begin the diagnostics.

The figure below indicates the proper connection between the router and the Yahoo server (www.Yahoo.com) tested through Ping.

The figure below indicates the proper connection between the router and the Yahoo server (www.Yahoo.com) tested through Tracert.

4. 10. 8. Time

This function allows you to set the time manually or to configure automatic time synchronization. The router can automatically update the time from an NTP server via the

internet.

1. Visit http://mwlogin.net, and log in with the password you set for the router.

2. Go to Advanced > System > Time & Language.

Page 65

Chapter 4 Congure the Router in Wireless Router Mode

• To set System Time:

1. In the System Time section, select the way in which the router gets its time: Get from

Internet, Get from Managing Device, Manually.

2. Select your local Time Zone.

3. Enter the address or domain of the NTP Server 1 or NTP Server 2.

4. Click SAVE.

• To set up Daylight Saving Time:

1. In the Daylight Saving Time section, tick the Enable box.

2. Select the start time from the drop-down list in the Start fields.

3. Select the end time from the drop-down list in the End fields.

4. Click SAVE.

Note:

This setting will be used for some time-based functions such as firewall. You must specify your time zone once you log in to

the router successfully; otherwise, time-based functions will not take effect.

Page 66

Chapter 4 Congure the Router in Wireless Router Mode

4. 10. 9. Language

This function allows you to set the language for the system.

1. Visit http://mwlogin.net, and log in with the password you set for the router.

2. Go to Advanced > System > Time & Language.

3. In the Language section, choose your desired language.

4. Click SAVE.

4. 10. 10. Reboot

Some settings of the router will take effect only after rebooting, and the system will reboot automatically. You can also reboot the router to clear cache and enhance running

performance.

1. Visit http://mwlogin.net, and log in with the password you set for the router.

2. Go to Advanced > System > Reboot, and you can restart your router.

• To reboot the router manually:

Click REBOOT, and wait a few minutes for the router to reboot.

• To set the router to reboot regularly:

1. Tick the Enable box of Reboot Schedule.

2. Specify the Reboot Time when the router reboots and Repeat to decide how often it

reboots.

3. Click SAVE.

Page 67

Chapter 4 Congure the Router in Wireless Router Mode

4. 10. 11. LED Control

The LED of the router indicates its activities and status. You can enable the Night Mode feature to specify a time period during which the LED is off.

1. Visit http://mwlogin.net, and log in with the password you set for the router.

2. Go to Advanced > System > LED Control.

3. Enable Night Mode.

4. Specify the LED off time, and the LED will be off during this period every day.

Note: The effective LED off time is based on the time of the router. You can go to Advanced > System > Time to modify the

time.

5. Click SAVE.

Page 68

Chapter 5

Congure the Router in Access Point Mode

Chapter 5. Congure the Router in Access Point Mode

This chapter presents how to configure the various features of the router working as an access point.

It contains the following sections:

• Operation Mode

• Firmware Upgrade

• Backup & Restore

• Administration

• System Log

• Diagnostics

• Time

• Language

• Reboot

• LED Control

5. 1. Operation Mode

1. Visit http://mwlogin.net, and log in with the password you set for the router.

2. Go to System > Operation Mode.

3. Select the working mode as needed and click SAVE.

Page 69

Chapter 5

Congure the Router in Access Point Mode

5. 2. Firmware Upgrade

1. Download the latest firmware file for the router from our website

2. Visit http://mwlogin.net, and log in with the password you set for the router.

3. Go to System > Firmware Upgrade.

4. Click BROWSE to locate the downloaded firmware file, and click UPGRADE.

www.mercusys.com.

5. 3. Backup & Restore

1. Visit http://mwlogin.net, and log in with the password you set for the router.

2. Go to System > Backup & Restore.

To backup configuration settings:

Click BACK UP to save a copy of the current settings in your local computer. A “.bin“ file of the current settings will be stored in your computer.

To restore configuration settings:

Page 70

Chapter 5

Congure the Router in Access Point Mode

1. Click BROWSE to locate the backup configuration file stored in your computer, and click

RESTORE.

2. Wait a few minutes for the restoring and rebooting.

To reset the router to factory default settings:

1. Click FACTORY RESTORE to reset the router.

2. Wait a few minutes for the restoring and rebooting.

Note:

• During the resetting process, do not turn off or reset the router.

• We strongly recommend you back up the current configuration settings before resetting the router.

5. 4. Administration

5. 4. 1. Change Password

1. Visit http://mwlogin.net, and log in with the password you set for the router.

2. Go to System > Administration, and focus on the Change Password section.

3. Enter the old password, then a new password twice (both case-sensitive). Click SAVE.

Page 71

Chapter 5

Congure the Router in Access Point Mode

4. Use the new password for future logins.

5. 4. 2. Local Management

1. Visit http://mwlogin.net, and log in with the password you set for the router.

2. Go to System > Administration, and focus on the Local Management section.

• Allow all LAN connected devices to manage the router:

Select All Devices for Local Managers.

• Allow specific devices to manage the router:

1. Select Specified Devices for Local Managers and click SAVE.

2. Click Add Device.

Page 72

Chapter 5

3. Click VIEW CONNECTED DEVICES and select the device to manage the router from the

Connected Devices list, or enter the MAC address of the device manually.

4. Specify a Description for this entry.

5. Click SAVE.

Congure the Router in Access Point Mode

5. 5. System Log

1. Visit http://mwlogin.net, and log in with the password you set for the router.

2. Go to System > System Log, and you can view the logs of the router.

3. Click SAVE TO LOCAL to save the system logs to a local disk.

5. 6. Diagnostics

Diagnostic is used to test the connectivity between the router and the host or other network devices.

1. Visit http://mwlogin.net, and log in with the password you set for the router.

2. Go to System > Diagnostics.

Page 73

Chapter 5

Congure the Router in Access Point Mode

3. Enter the information:

1 ) Choose Ping or Tracert as the diagnostic tool to test the connectivity.

• Ping is used to test the connectivity between the router and the tested host, and

measure the round-trip time.

• Tracert is used to display the route (path) your router has passed to reach the

tested host, and measure transit delays of packets across an Internet Protocol network.

2 ) Enter the IP Address or Domain Name of the tested host.

3 ) Modify the Ping Count number and the Ping Packet Size. It’s recommended to

keep the default value.

4 ) If you have chosen Tracert, you can modify the Traceroute Max TTL. It’s

recommended to keep the default value.

4. Click START to begin the diagnostics.

The figure below indicates the proper connection between the router and the Yahoo server (www.Yahoo.com) tested through Ping.

The figure below indicates the proper connection between the router and the Yahoo server (www.Yahoo.com) tested through Tracert.

Page 74

Chapter 5

Congure the Router in Access Point Mode

5. 7. Time

This function allows you to set the time manually or to configure automatic time synchronization. The router can automatically update the time from an NTP server via the

internet.

1. Visit http://mwlogin.net, and log in with the password you set for the router.

2. Go to System > Time & Language.

• To set System Time:

1. In the System Time section, select the way in which the router gets its time: Get from

Internet, Get from Managing Device, Manually.

2. Select your local Time Zone.

3. Enter the address or domain of the NTP Server 1 or NTP Server 2.

4. Click SAVE.

• To set up Daylight Saving Time:

1. In the Daylight Saving Time section, tick the Enable box.

Page 75

Chapter 5

Congure the Router in Access Point Mode

2. Select the start time from the drop-down list in the Start fields.

3. Select the end time from the drop-down list in the End fields.

4. Click SAVE.

Note:

This setting will be used for some time-based functions such as firewall. You must specify your time zone once you log in to

the router successfully; otherwise, time-based functions will not take effect.

5. 8. Language

This function allows you to set the language for the system.

1. Visit http://mwlogin.net, and log in with the password you set for the router.

2. Go to System > Time & Language.

3. In the Language section, choose your desired language.

4. Click SAVE.

5. 9. Reboot

Some settings of the router will take effect only after rebooting, and the system will reboot automatically. You can also reboot the router to clear cache and enhance running

performance.

1. Visit http://mwlogin.net, and log in with the password you set for the router.

Page 76

Chapter 5

2. Go to System > Reboot, and you can restart your router.

• To reboot the router manually:

Click REBOOT, and wait a few minutes for the router to reboot.

• To set the router to reboot regularly:

1. Tick the Enable box of Reboot Schedule.

2. Specify the Reboot Time when the router reboots and Repeat to decide how often it

reboots.

3. Click SAVE.

Congure the Router in Access Point Mode

5. 10. LED Control

The LED of the router indicates its activities and status. You can enable the Night Mode feature to specify a time period during which the LED is off.

1. Visit http://mwlogin.net, and log in with the password you set for the router.

2. Go to System > LED Control.

3. Enable Night Mode.

Page 77

Chapter 5

Congure the Router in Access Point Mode

4. Specify the LED off time, and the LED will be off during this period every day.

Note: The effective LED off time is based on the time of the router. You can go to Advanced > System > Time to modify the

time.

5. Click SAVE.

Page 78

FAQ

Q1. What should I do if I forget my wireless password?

The default wireless password is printed on the bottom label of the router.

If the password has been altered, please connect your computer to the router using

an Ethernet cable and follow the steps below:

1. Visit http://mwlogin.net, and log in with the password you set for the router.

2. Go to Wireless or Advanced > Wireless > Wireless Settings to retrieve or reset

your wireless password.

Q2. What should I do if I forget my login password of the web management

page?

1. Reset the router to its factory default settings.

2. Visit http://mwlogin.net, and create a password for future login.

Note: You’ll need to recongure the router to surf the internet once the router is reset, and please mark down your new

password for future use.

Q3. What should I do if I cannot log in to the router’s web management page?

This can happen for a variety of reasons. Please try the methods below to log in

again.

• Make sure the router connects to the computer correctly and the corresponding

LED light up.

• Make sure the IP address of your computer is congured as Obtain an IP address

automatically and Obtain DNS server address automatically.

• Make sure you enter the correct IP address to log in: http://mwlogin.net or

192.168.1.1.

• Check your computer’s settings:

1 ) Go to Start > Control Panel > Network and Internet, and click View network

status and tasks.

2 ) Click Internet Options on the bottom left.

3 ) Click Connections and select Never dial a connection.

Page 79

FAQ

4 ) Click LAN settings and deselect the following three options, and click OK.

5 ) Go to Advanced > Restore advanced settings, and click OK.

Page 80

FAQ

• Use another web browser or computer to log in again.

• Reset the router to factory default settings and try again. If the login still fails,

please contact the technical support.

Note: You’ll need to recongure the router to surf the internet once the router is reset.

Q4. What should I do if I cannot access the internet even though the

conguration is nished?

1. Visit http://mwlogin.net, and log in to with the password you set for the router.

2. Go to Advanced > Network > Status to check the Internet status:

If IP Address is a valid one, please try the methods below and try again:

• Your computer might not recognize any DNS server addresses, please manually

congure DNS server.

1 ) Go to Advanced > Network > DHCP Server.

2 ) Enter 8.8.8.8 as Primary DNS, and click Save.

Tips: 8.8.8.8 is a safe and public DNS server operated by Google.

• Restart the modem and the router.

Page 81

1 ) Power o your modem and the router, and leave them o for 1 minute.

2 ) Power on your modem rst, and wait about 2 minutes.

3 ) Power on the router, and wait another 1 or 2 minutes and check the Internet

access.

• Reset the router to factory default settings and recongure the router.

• Upgrade the rmware of the router.

• Check the TCP/IP settings on the particular device if all other devices can get

internet from the router.

If the IP Address is 0.0.0.0, please try the methods below and try again:

• Make sure the physical connection between the router and the modem is proper.

• Clone the MAC address of your computer.

1 ) Visit http://mwlogin.net, and log in with the username and password you set

for the router.

FAQ

2 ) Go to Advanced > Network > Internet, select Clone Current Device MAC

and click SAVE.

Tips:

• Some ISP will register the MAC address of your computer when you access the Internet for the rst time through

their Cable modem, if you add a router into your network to share your Internet connection, the ISP will not accept it

as the MAC address is changed, so we need to clone your computer’s MAC address to the router.

• The MAC addresses of a computer in wired connection and wireless connection are dierent.

• Modify the LAN IP address of the router.

Note:

Mercusys routers use 192.168.1.1 as their default LAN IP address. It may conict with the IP range of your existent ADSL

modem/router. If so, the router is not able to communicate with your modem and cause you can’t access the Internet. To

resolve this problem, we need to change the LAN IP address of the router to avoid such conict, for example, 192.168.2.1.

1 ) Visit http://mwlogin.net, and log in with the username and password you set

for the router.

2 ) Go to Advanced > Network > LAN.

3 ) Modify the LAN IP address as the follow picture shows. Here we take

192.168.2.1 as an example.

4 ) Click Save.

Page 82

• Restart the modem and the router.

1 ) Power o your modem and the router, and leave them o for 1 minute.

2 ) Power on your modem rst, and wait about 2 minutes.

3 ) Power on the router, and wait another 1 or 2 minutes and check the internet

access.

• Double check the Internet Connection Type.

FAQ

1 ) Conrm your Internet Connection Type, which can be learned from the ISP.

2 ) Visit http://mwlogin.net, and log in with the username and password you set

for the router.

3 ) Go to Advanced > Network > WAN.

4 ) Select your Internet Connection Type and ll in other parameters.

5 ) Click SAVE.

6 ) Restart the modem and the router.

• Please upgrade the rmware of the router.

If you’ve tried every method above but cannot access the internet, please contact

the technical support.

Q5. What should I do if I cannot nd my wireless network or I cannot connect to

the wireless network?

If you fail to nd any wireless network, please follow the steps below:

• Make sure the wireless function of your device is enabled if you’re using a laptop

with a built-in wireless adapter. You can refer to the relevant document or contact

the laptop manufacturer.

• Make sure the wireless adapter driver is installed successfully and the wireless

adapter is enabled.

• On Windows 7

Page 83

FAQ

1 ) If you see the message No connections are available, it is usually because

the wireless function is disabled or blocked somehow.

2 ) Clicking Troubleshoot and windows might be able to x the problem by itself.

• On Windows XP

1 ) If you see the message Windows cannot congure this wireless

connection, this is usually because windows conguration utility is disabled

or you are running another wireless conguration tool to connect the

wireless.

2 ) Exit the wireless conguration tool (the Mercusys Utility, for example).

3 ) Select and right click My Computer on Desktop, and select Manage to open

Computer Management window.

4 ) Expand Services and Applications > Services, and nd and locate Wireless

Zero Conguration in the Services list on the right side.

5 ) Right click Wireless Zero Conguration, and then select Properties.

6 ) Change Startup type to Automatic, click Start and make sure the Service

status is Started. And then click OK.

If you can nd other wireless network except your own, please follow the steps

below:

• Make sure your computer/device is still in the range of your router/modem. Move

closer if it is currently too far away.

If you can nd your wireless network but fail to connect, please follow the steps

below:

• Authenticating problem/password mismatch:

1 ) Sometimes you will be asked to type in a PIN number when you connect to

the wireless network for the rst time. This PIN number is dierent from the

Wireless Password/Network Security Key. Usually you can only nd it on the

label of your router.

Page 84

2 ) If you cannot nd the PIN or PIN failed, you may choose Connecting using

a security key instead, and then type in the Wireless Password/Network

Security Key.

3 ) If it continues to show note of Network Security Key Mismatch, it is

suggested to conrm the wireless password of your wireless router.

FAQ

Note: Wireless Password/Network Security Key is case sensitive.

• Windows unable to connect to XXXX / Can not join this network / Taking longer

than usual to connect to this network:

• Check the wireless signal strength of your network, if it is weak (1~3 bars),

please move the router closer and try again.

• Change the wireless Channel of the router to 1, 6, or 11 to reduce

interference from other networks.

• Re-install or update the driver for your wireless adapter of the computer.

Mercusys MR70X User guide

Specifications and Main Features

Frequently Asked Questions

User Manual

Conventions

Chapter 1. Introduction

1. 1. Product Overview

1. 2. Product Appearance

1. 2. 1. Front Panel

1. 2. 2. Rear Panel

Chapter 2. Connect to the Internet

2. 1. Position Your Router

2. 2. Connect to the Internet

Chapter 3. Log In to the Router

4. 2. Network

4. 2. 1. Status

4. 2. 2. Internet

4. 2. 3. MAC Clone

4. 2. 4. LAN

4. 2. 5. IPTV/VLAN

4. 2. 6. DHCP Server

4. 2. 7. Dynamic DNS

4. 2. 8. Static Routing

4. 3. Wireless

4. 3. 1. Wireless Settings

4. 3. 2. Guest Network

4. 3. 3. Wireless Schedule

4. 3. 4. WPS

4. 3. 5. Additional Settings

4. 4. NAT Forwarding

4. 4. 1. Port Forwarding

4. 4. 2. Port Triggering

4. 4. 3. UPnP

4. 4. 4. DMZ

4. 5. Parental Controls

4. 6. QoS

4. 7. Security

4. 7. 1. Firewall

4. 7. 2. Access Control

4. 7. 3. IP & MAC Binding

4. 7. 4. ALG

4. 8. VPN Server

4. 8. 1. OpenVPN

4. 8. 2. PPTP VPN

4. 9. IPv6

4. 10. System

4. 10. 1. Firmware Upgrade

4. 10. 2. Backup & Restore

4. 10. 3. Change Password

4. 10. 4. Local Management

4. 10. 5. Remote Management

4. 10. 6. System Log

4. 10. 7. Diagnostics

4. 10. 8. Time

4. 10. 9. Language

4. 10. 10. Reboot

4. 10. 11. LED Control

5. 1. Operation Mode

5. 2. Firmware Upgrade

5. 3. Backup & Restore

5. 4. Administration

5. 4. 1. Change Password

5. 4. 2. Local Management

5. 5. System Log

5. 6. Diagnostics

5. 7. Time

5. 8. Language

5. 9. Reboot

5. 10. LED Control