Page 1
Assembly Instructions
ASSEMBLY RATING
The Assembly
shows the degree of effort needed in
assembling a specific product (with 1 being easy
and 5 being difficult). For some products, two
persons are recommended.
EASY
Rating is a 5-point system that
DIFFICULT
Page 1 of 5
Tools Required For Assembly:
Allen Wrench
(Included)
Phillips Screwdriver
(Not Included)
2 PERSONS RECOMMENDED
Page 2
FOR YOUR FURNITURE TO LAST,CORRECT ASSEMBLY AND PROPER MAINTENANCE ARE NECESSARY.
PLEASE FOLLOW THE INFORMATION PROVIDED BELOW TO FULLY ENJOY YOUR FURNITURE.
BASIC ASSEMBLY TECHNIQUES
FAILURE TO FOLLOW THE GUIDELINES ABOVE MAY
RESULT IN INJURY AND/OR PROPERTY DAMAGE.
When lock or spring washer is used in
an assembly, please make sure the
lock or spring washer is placed
between the larger flat washer and the
head of the screw or bolt.
Position each part correctly and insert
screws or bolts into their respective
holes by hand tighten or using the
proper hand tool. Only tighten when
step is completed or when instructed
to do so.
Use cardboard or carpet area when
assembling furniture to prevent
scratches Make sure the furniture
rests on a flat and level surface with
each leg evenly touching the floor.
IT IS THE USER'S RESPONSIBILITY TO MAINTAIN THE FURNITURE.THE HARDWARE MA
Y
LOOSEN OVER TIME AND MAY CAUSE THE FURNITURE TO BE WOBBLY AND UNABLE TO
SUPPORT ITS INTENDED WEIGHT CAPACITY. THIS MAY LEAD TO COLLAPSE AND MAY
CAUSE SERIOUS INJURY.
Some furniture comes with height
adjusetment knobs underneath each
leg. To lower or to raise each leg, you
need to turn clockwise or
counterclockwise, respectively.
Make sure all parts are properly
aligned, then use the appropriate
hand tool to completely tighten the
bolts or screws. Do not use power
tools and do not overtighten.
Save the instructions and store the Allen
wrench or any supplied tool for later
maintenance. After two weeks, check
and tighten any loose hardware and
repeat again every six months thereafter.
Page 2 of 5
ALL RIGHTS RESERVED.
Page 3
Page 3 of 5
Before you begin, please read Page 2
of "Assembly and Care Advice".
And remember, do not tighten until
each step is completed or instructed.
#A x 6pcs
Bolt Ø1/4" x 1-3/8"
Parts List Hardware List
#1 x 1pc
Headboard
#2 x 2pcs
Headboard Leg (L&R)
#3 x 1pc
Footboard
#4 x 2pcs
Rail
#5 x 1Set (13pcs)
Bed Slat
#6 x 1pc
Center Rail
#B x 6pcs
Lock washer Ø1/4"
#D x 1pc
Allen wrench M4
#C x 6pcs
Flat washer
Ø1/4"-3/4"
#E x 12pcs
Screw
#5/32"x1-3/16''
#7 x 4pcs Ø5/16
Support Leg (310x30x30mm)
Page 4
#A x 6pcs
#B x 6pcs
#C x 6pcs
Page 4 of 5
#D
#A
#B
#C
#1
#4
#3
#1
#2R
#2L
#4
Prepare 6 bolts assembly by inserting lock washer (#B), then flat washer (#C) onto bolts (#A).
Align headboard legs (#2R/L) to the holes of the headboard (#1). Secure with bolts (#A).
Hook the side rails (#4) to the latch of the headboard (#1) and footboard (#3).
Make sure the side rails (#4) are on firmly.
Page 5
#E x 12pcs
Page 5 of 5
ASSEMBLY IS COMPLETED
#5
#E
#4
#5
#6
#7
#4
Attach 4 support legs (#7) to center rail (#6). Adjust
floor protector according to ground level.
Align slats (#5) to the side rails (#4) and center rail (#6), then secure with screws (#E).
Page 6
Page 7
Page 8
Page 9
1. Prepare 6 bolt assemblies by first
inserting a lock washer (#B) onto
the bolt (#A) then a flat washer
(#C) onto that same bolt (#A).
2. Align the legs (#2) to the holes along the side of
the headboard (#1), then insert the bolts and secure.
Hook each end of the side rails
(#4) onto the slots along the headboard (#1) and foot board (#3).
Page 10
Insert the threaded ends of the support
legs (#7) into the holes along the center
rail (#6), turn right to tighten.
Adjust according
to the ground level.
Place the bed slats (#5)
onto the rails, then
insert a screw (#E) into
each hole. Secure
using a screwdriver.
Page 11
Prepare 10 bolt assemblies
by first inserting a lock
washer (#B) onto the bolt
(#A) then a flat washer (#F)
onto that same bolt (#A).
Insert into the holes. Secure.
Loading...