Page 1
Installation Guide
ToolsRequired: Flatheadscrewdriver, Phillipsscrewdriver,pliers,wire cutters,wire strippers,electricaltape, safetyglasses.
LightSource:
EstimatedAssembly Time:
Preparation:
present.Ifany partsare missingordamaged, donot attempttoassemble, install,or operatethefixture. MissingParts? Contactyouroriginal placeof
purchase.
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal.
(3)B10Candelabra Basebulbs 60WMaximum,bulb notincluded.
30-45minutes
Identifyandinspect allparts beforebeginninginstallation. Checkpackage contentlistand diagramsbelow toensureall partsare
Package Contents
Fixture Body
C
Crossbarx1Assembly
A
B
STEP 1 - Install the CrossbarAssembly to Outlet Box andAdjust
the length of the Nipple
a. Unfold support arms on Fixture Body (C) to proper locations.
b. Attach the Crossbar Assembly (A) to the Outlet Box with the head of
the Green Ground Screw facing you. Secure it with Outlet Box
Screws (not included), tighten until snug
c. Adjust the hex nut and lock washer underside of the crossbar to the
middle of the nipple.
d. Remove the from the Nipple. Place the Fixture Canopy
over the Nipple against the ceiling to determine the correct position
of the nipple. Thread the Finial onto the Nipple. Adjust the nipple to
allow the Fixture Canopy to rest against the ceiling when held in
place by the .
e. Remove the and the Fixture Canopy. Tighten the lock
washer against the crossbar to secure in place.
Green Ground Screw
Lock Ball
Lock Ball
Lock Ball
A
x1
Glass
x3
.
Outlet Box
STEP 2 - Wire Connections
Wrap bare or green ground wire around green ground screw on the
A.
crossbar, no less than 2 inches from the end of the wire. Tighten the
green ground screw.
B. Use standard wire connectors (not included) to make all wire
connections. Twist connectors until wires are tightly joined together.
Wrap each connection with approved electrical tape and carefully
stuff all the connected wires into the Outlet Box.
White wire
Figure 2
STEP 3 Install Fixture Body to Crossbar-
A. Attach the Fixture Body (C) over the end of the Nipple and secure
with the . Hand tighten until snug.
from outlet box
Black wire from
outlet box (or Red)
Bare, or Green
Ground wire
from outlet box
Lock Ball
Crossbar
Nipple
Green Ground Screw
on the Crossbar
White wire
from fixture
Black wire
from fixture
Ground wire
from Fixture
Outlet Box Screw
(not included)
Hex Nut and
Lock Washer
Nipple
Lock Ball
Fixture Canopy
Lock Ball
Figure 3
Top View
1of1
Page 2
STEP 4 - Install the Glass and the Bulb
a. Place the Glass (B) into the hood on the fixture body (C) and
secure with lock screws. Hand-tighten until snug.
B. Insert the bulb onto the socket and screw snugly into place.
Your fixture is now assembled and ready to use. Enjoy!
Lock Screw
Bulb(not included)
Figure 4
FINISH: SATIN BRASS
20.5” Dia.
6” Dia.
C
Socket
B
10.75"
6"
NOTE: ALL DIMENSIONS ARE ROUNDED UP TO THE NEAREST 1/4"
1of1
Loading...