Page 1
Assembly Instruction Sheet
ToolsRequired: Flathead screwdriver,Phillipsscrewdriver,pliers, wire cutters, wire strippers, electrical tape, safety glasses.
LightSource:
EstimatedAssembly Time:
Preparation:
present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.Contactcustomerserviceforreplacement
parts.
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal.
(1)A21 MediumBase bulb150W Maximumor
(1)MediumBaseVintageBulbisrecommendedbutnotsupplied.
20-30minutes
Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtoensureallpartsare
Package Contents
Fixture Loop
A
x1
Waterproof
B
Washer
x1
C
STEP 1 Install Glass Panels-
A. Insert the Glass Panel (C) into the
cage with beveled edge is
outside. Attach the top edge of the
Glass Panel (C) to the slot in the
top of the cage. Fold tabs in the
bottom edge of the cage to secure
Glass Panels (C).
B. Place the Waterproof Washer (B)
over the nipple on the top center
of the Fixture Body (D) and thread
the Fixture Loop (A) onto the
nipple. Hand tighten until snug.
Glass Panel
x4
Slot
Cage
Fixture Body
D
x1
Hardware Contents
Crossbar
AA
x1
Lock Washer
BB
x2
Hex Nut
CC
x2
Nipple
DD
x1
A
B
STEP 2 Install the Crossbar to the junction box-
A. Attach the Crossbar (AA) to the Outlet Box with the head of the
Green Ground Screw facing you. Secure it with Outlet Box Screws
(not included), tighten until snug
Green Ground
D
Screw
.
Figure 2
HH
Outlet Box
AA
Outlet Box Screw
(not included)
Canopy
EE
Chain Loop
x1
Canopy Lock
FF
Ring
x1
Fixture Chain
GG
x1
Quick Link
x2
Ceiling Canopy
II
x1
Figure 1
Tab
STEP 3 Install the Canopy Chain Loop and Nipple-
A. Thread one Hex Nut (CC) to one end of the Nipple (DD) until it is at
least 0.25” from the end. Pass one Lock Washer (BB) over the end
of the Nipple (DD) and thread the Canopy Chain Loop (EE) onto the
Nipple (DD). By using pliers, thread the Hex Nut (CC) against the
Canopy Chain Loop (EE) and hand tighten until snug.
B. Thread another Hex Nut (CC) to the middle of the Nipple (DD).
Place another Lock Washer (BB) over the Nipple (DD) and then
C
Thank you for purchasingthis product.
thread the Nipple (DD) into the Crossbar (AA) until the Nipple (DD)
is about 0.375” above the Crossbar (AA).
C. Remove the Canopy Lock Ring (FF) from the Canopy Chain Loop
(EE). Place the Ceiling Canopy (II) over the Canopy Chain Loop
(EE) against the ceiling to determine the correct position of the
Nipple (DD). Thread the Canopy Lock Ring onto the Canopy Chain
Loop (EE). Adjust the Nipple (DD) to allow the Ceiling Canopy (II) to
1of3
Page 2
(Step 3 Continued)
STEP 5 - Making the Wire Connections
rest against the ceiling
when held in place by the
Canopy Lock Ring (FF).
D. Remove the Canopy Lock
Ring (FF) and the Ceiling
AA
BB
CC
Step B
Canopy (II). Tighten the
Hex Nut (CC) against the
Crossbar (AA) to secure in
DD
place.
CC
EE
Figure 3
FF
BB
Step A
II
STEP 4 - Install the Fixture Chain and Ceiling Canopy
A. Adjust the Fixture Chain (GG) to your desired length by removing
links if needed.
B. Pull the supply wires through the Fixture Chain (GG) alternating
links. After the wires are through the Fixture Chain (GG), pull the
Supply Wires and the Ground Wire through the Canopy Lock Ring
(FF) and the Ceiling Canopy (II) in order.
C. Attach one end of the Fixture Chain (GG) to the Fixture Loop with
one Quick Link (HH). Lift the fixture and Fixture Chain (GG) up and
attach the other end of the Fixture Chain (GG) onto the Canopy
Chain Loop (EE) with another Quick Link (HH). The fixture will now
hang safely.
D. Feed the Supply Wires and Ground Wire through the Canopy Chain
Loop (EE) and Nipple (DD) into the Outlet Box. Cut the wires leaving
approximately 8” of wire extending from the Outlet Box.
E. Go to Step 5 for wire connections and follow the directions. Return
to Step F in this step when complete with Step 5.
F. Raise the Ceiling Canopy (II) and Canopy Lock Ring (FF) up the
Fixture Chain (GG) and over
the Canopy Chain Loop (EE).
Tighten the Canopy Lock Ring
(FF) onto the Canopy Chain
Loop (EE) until tight.
DD
Suggested chain length for
Ceiling height :
8’ ceiling : use 10 links of chain
and 2 quick links
9’ ceiling : use 20 links of chain
and 2 quick links
10’ ceiling : use 30 links of
chain and 2 quick links
Supply
Wires and
Ground Wire
GG
EE
HH
A. Wrap bare or green ground wire around green ground screw on the
crossbar, no less than 2 inches from the end of the wire. Tighten the
green ground screw.
B.
Use standard wire connectors (not included) to make all wire
connections. Twist connectors until wires are tightly joined together.
Wrap each connection with approved electrical tape and carefully
stuff all the connected wires into outlet box.
Note: If the electrical wire is going to be cut shorter than provided
you will need to identify the "L" line wire and the "N" neutral wire
before you cut the excess wire off. One is labeled N and the other
labeled L. To do this separate the "L" line wire and the "N" neutral
wire as far as you need to. Re-label the wire near where you want to
make the cut. Be sure to mark the wire on the side of the fixture and
not on the excess wire being cut and removed.
White wire
from outlet box
Black wire from
outlet box (or Red)
Bare, or Green
Ground wire
from outlet box
Green Ground Screw
White wire from fixture
identified with the Label “N”
Black wire from fixture
identified with the label “L”
Ground wire
from Fixture
Figure 5
on the Crossbar
STEP 6 - Install the Bulb
A. Insert the bulb onto the socket and screw snugly into place.
Your fixture is now assembled and ready to use. Enjoy!
Socket
Figure 4
II
Vintage Bulb
(recommended
but not Supplied)
FF
HH
Fixture
Loop
Thank you for purchasingthis product.
2of3
Figure 6
Page 3
FINISH: EARTH BLACK
NOTE: ALL DIMENSIONS ARE ROUNDED UP TO THE NEAREST 1/4"
5" Dia.
122.5” OVERALL
HEIGHT INCLUDES
96” CHAIN AND
2 QUICK LINKS()
7"
20.75"
7"
Thank you for purchasingthis product.
3of3
Loading...