Page 1
WARNING: DISCONNECT POWER AT THE MAIN
FUSE BOX BEFORE INSTALLATION.
WARNING:
This xture is intended for installation in
accordance with the National Electrical Code
(NEC) and all local code specications. If you are
not familiar with code requirements, installation
by a certied electrician is recommended.
Before assembly, remove all parts and part
packages from box. If anything is missing, please
contact the retailer from which the product was
purchased.
1. Carefully pull house wires out of junction box so
they are easily accessible during installation.
2. Position mounting bracket (A) so threaded ends
of attached xture mounting screws (E) are
facing down towards oor.
3. Carefully pull house wires through center hole
in mounting bracket (A).
4. Align small holes in mounting bracket (A) with
holes in junction box.
5. Thread each junction box screw (B) into holes in
mounting bracket (A) and into holes in junction
box. Tighten junction box screws (B) to secure
mounting bracket (A) to junction box.
CAUTION: Make sure house wires are pulled
completely through hole in mounting bracket.
DO NOT pinch wires between mounting bracket
and ceiling.
ANY QUESTIONS CALL: 800-613-3261
M-F 8:00AM-6:00PM ET
ITEM#: CN701151
A
E
B
E
B
JUNCTION
BOX
6. The length of the cord must be adjusted before
xture is installed. Hold canopy (D) against
ceiling to determine desired hanging height of
xture.
7. Using screwdriver, loosen set screw on strain
relief (V) on canopy (D) to release cord (H) (Do
not completely remove set screw). Carefully
pull cord (H) down or push cord (H) up through
canopy (D) to achieve desired length. Tighten set
screw on strain relief (V) to secure cord (H).
8. Insert end of cord through each hole in cord clip
(W). Slide cord clip (W) down towards inside of
canopy.
D
V
H
W
H
1
elkhome.com
Page 2
ITEM#: CN701151
9. Strip 3/4” of insulation from ends of xture
wires.
10. Slightly loosen ground screw on mounting
bracket (A). Do not completely remove ground
screw. Wrap house ground wire (copper) around
ground screw, leaving enough ground wire
to attach to xture ground wire. Twist end of
xture ground wire and end of house ground
wire (copper) together. Twist wire connector
(C) onto ends of wires. Completely tighten wire
connector (C). Reference chart below for correct
wire connections.
Connect Supply (House) Ground Copper Wire to:
Bare Copper Wire or,
Bare Silver Wire or,
Green Insulated Wire.
GROUND
SCREW
A
HOUSE GROUND
WIRE (COPPER)
C
FIXTURE
GROUND WIRE
11. Twist end of house lead wire (black) and end of
xture lead wire together. Twist wire connector
(C) onto ends of wires. Completely tighten wire
connector (C). Twist end of house neutral wire
(white) and end of xture neutral wire together.
Twist wire connector (C) onto ends of wires.
Completely tighten wire connector (C). Reference
chart to the right for correct wire connections.
12. Wrap electrical tape (not included) around wire
connectors (C) and wires. Ensure wires are
securely fastened into wire connectors.
13. Carefully push all wires and wire connectors into
junction box.
Connect Black Lead
Supply (House) Wire to:
Black Wire or,
*Parallel Cord
(Round and Smooth) or,
No printed words on
wire insulation or,
Insulated Wire
(other than green)
with Copper Conductor.
*When parallel wire (SPT 1 & SPT 2) is used:
The lead wire is round in shape or smooth.
The neutral wire is square in shape or ridged.
FIXTURE LEAD WIRE HOUSE LEAD WIRE
FIXTURE GROUND
WIRE
FIXTURE NEUTRAL
WIRE
Connect White Neutral
Supply (House) Wire to:
White Wire or,
*Parallel Cord
(Square and Ridged) or,
Printed words on
wire insulation or,
Insulated Wire
(other than green)
with Silver Conductor.
(BLACK)
HOUSE GROUND
WIRE (COPPER)
HOUSE NEUTRAL WIRE
(WHITE)
2
elkhome.com
Page 3
ITEM#: CN701151
14. Carefully raise xture up to ceiling. Place
canopy (D) over mounting bracket (A). Pass
holes in canopy (D) over ends of xture
mounting screws (E).
15. Screw one threaded cap (F) onto end of each
xture mounting screw (E). Tighten threaded
caps (F) to secure xture to ceiling. DO NOT over
tighten.
16. Screw recommended bulb (E26 Edison bulb
type, not included) into socket. Verify correct
bulb wattage marked on socket of xture.
WARNING: DO NOT exceed maximum bulb
wattage.
A
E
D
E
FF
BULB
3
elkhome.com
Loading...