Mercury Row W005208702 Installation & Assembly

Page 1
Installation Guide
lease go to the Care + Maintenance selection.
P
Tools Required: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses. Light Source: Fixture Hanging Height: Estimated Assembly Time: Preparation:
present. If any parts are missing or damaged, do not attempt to assemble, install, or operate the fixture. Missing Parts? Contact your original place of purchase.
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal.
(1)A19 Medium Base 100W bulb Maximum, bulb not included.
Minimum Hanging Height is 20”, Maximum Hanging Height is 111.5”.
30-45 minutes
Identify and inspect all parts before beginning installation. Check package content list and diagrams below to be sure all parts are
Package Contents
Fixture
B
Body x1
Crossbar
A
Assembly x1
Shade
C
x1
STEP 1 Adjust Fixture Height-
A. Loosen the set screw on the coupling underside of the ceiling
canopy.Adjust the cord in or out of the ceiling canopy according to your hanging height.
B. Tighten the set screw on the coupling once your hanging height
is achieved. Move the safety clip next to the hex nut inside of the ceiling canopy.
Safety Clip
STEP 2 - Installing the CrossbarAssembly
A. Pass the supply wires from outlet box through the Crossbar
Assembly (A). Attach the Crossbar Assembly (A) to the Outlet Box with the head of the Green Ground Screw facing you. Secure the Crossbar Assembly (A) with Outlet Box Screws (not included). Tighten until snug.
Outlet Box
A
Supply Wires with
Ground Wire
Figure 2
STEP 3 Test Fitting Ceiling Canopy to Crossbar Assembly-
A.
Remove mounting balls from the Crossbar Assembly (A). Fit the Ceiling Canopy to the mounting balls. Note: The should be snug against
ceiling
the and the mounting balls. If not, adjust the length of the nipple on the Crossbar Assembly (A) by unscrewing the preassembled hex nut and lock washer and then screwing the mounting screws in or out of the crossbar until the correct length is achieved. Once the Ceiling Canopy is secure, remove the mounting ball and Ceiling Canopy and proceed to Step 4.
Crossbar Assembly (A) and secure with
Ceiling Canopy
Outlet Box Screws (not included)
Cord
Hex Nut
Ceiling Canopy
Set Screw
Coupling
B
Cord
Figure 1
Screwdriver
1of2
Ceiling Canopy
A
Hex Nut and Lock Washer
Mounting Screw
Mounting Ball
Figure 3
Released
Date:2018-08-23
Page 2
STEP 4 - Wire Connections
A. Wrap bare or green ground wire around green ground screw on the
crossbar, no less than 2 inches from the end of the wire. Tighten the green ground screw.
B. Use standard wire connectors (not included) to make all wire
connections. Twist connectors until wires are tightly joined together. Wrap each connection with approved electrical tape and carefully stuff all the connected wires into the Outlet Box.
C. If the electrical wire is going to be cut shorter than provided, strip
back the clear wire covering the 3 fixture wires as far as you need to. This will expose each fixture wire individually. Strip each end of 3 fixture wires.
White wire
from outlet box
Black wire from
outlet box (or Red)
White wire from fixture
Black wire from fixture
Figure 4
NGA1510PK
FINISH: POLISHED NICKEL
4.75” Dia.
Bare,orGreen
Ground wire
from outlet box
Green Ground Screw on the Crossbar
Ground wire from Fixture
STEP 5 Install the Fixture-
A. Carefully tuck all wires into the outlet box and position the Ceiling
Canopy over the outlet box.Align the holes in the Ceiling Canopywith the mounting screws, then attach the Ceiling Canopy using the previously removed mounting balls. Hand tighten until snug.
A
Mounting Screw
Ceiling Canopy
Mounting Ball
Figure 5
STEP 6 - Install Shade and Bulb
A. Remove Stem from Fixture Body
Figure 6
(B).
B. Place the holes of the shade (C)
over the bolts on the underside of the Fixture Body (B). Secure
B
the Shade (C) by threading the Stem onto the bolts. Hand tighten until snug.
C. Insert bulbs onto sockets and
screw snugly into place.
Your fixture is now assembled and ready to use. Enjoy!
Socket
T10 Vintage Bulb (recommended but not included)
111. 5 ”
14”
12.5”
9.5” Dia.
C
NOTE: ALL DIMENSIONS ARE ROUNDED UP TO THE NEAREST 1/4"
Released
Date:2018-08-23
2of2
Loading...