Mercury Row W005206594 Installation & Assembly

Page 1
TV Stand
Thank you for purchasing TV Stand
!Before you start, here are some helpful advice:
1.We suggest you spend a short time reading through this leaflet and then follow the simple step-by-step
instructions.
2.Owing to the size and weight of the TV Stand, we recommend that it is assembled by two adults, on a carpeted or
padded area, in the room that it is intended for. Approximate assembly time: 60 minutes.
3.Please do not use any tools other than those provided or recommended in these instructions.
hardware and the furniture is fully assembled.
5.Assemble all components loosely until advised to tighten. Depending on use, it may be necessary to tighten the
components from time to time, so please save the tools that have been provided.
6.Please keep all pieces out of reach of children.
Hardware :
Cambolt/Metal
A)
Ø 6 x 35 mm
Shelf Pin/Metal
F)
Ø 5 x 15 mm
K)
Pin Sliding Top/Plastic
Ø 8 x 19 mm
P)
Screwdriver (Not Include)
x 10
x 12
B)
Ø 15 mm
G)
M 3.5 x 15.5 mm
L)
x 4
Ø 8 mm
x 1
CamLock/Metal
Screw/Metal
Buffer/Rubber
C)
Ø 8 x 30 mm
x 10
H)
9 x 14 x 10 mm
x 10
M)
x 1
42 x 14 x 8 mm
Dowel/Wood
Wedge/Plastic
Stopper/Plastic
D)
x 40
M 12 x 35 mm
I)
25 x 25 x 2 mm
x 10
N)
Ø 8 x 16 mm
x 2
Screw/Metal
x 6
Foam Pad/Spon
x 4
Pin Sliding Bottom/Plastic
x 4 x 6
Screw/Metal
E)
M 7 x 50 mm
J)
L 4
O)
Key/Metal
Screw Cup/Plastic
Ø 15 mm
x 6
x 1
Page 1 of 9
Page 2
Components:
1
3
12
5
11
14
13
6
12
4
11
2
8
9
7
10
9
7
8
Top Board x1
1
Center Board 1 x1 Center Board 2 x1
5
Support Board 2 x2
9
Adjustable Shelf 2 x1
13
Bottom Board x1
2
6
Support Board 3 x1
10
14
Back Board x1
Side Board Left x1
3
Leg x2
7
Door x2 Adjustable Shelf 1 x2
11
4 Side Board Right x1
Support Board 1 x2
8
12
Page 2 of 9
Page 3
TV Stand
STEP 1:
1
3
4
STEP 2:
5
6
Ax6 Hardware required. Screwdriver not included
Cx16 Px1
7
9
10
8
Ax4 Hardware required. Screwdriver not included
Cx20 Px1
Page 3 of 9
Page 4
STEP 3:
8
9
8
10
9
7
STEP 4:
Bx2 Px1
Hardware required. Screwdriver not included
7
Bx2 Px1
Hardware required. Screwdriver not included
Page 4 of 9
Page 5
STEP 5:
To be continued to Step 8
STEP 6:
Cx4
Hardware required
4
6
5
3
Bx6
Ox6 Px1
1
Hardware required. Screwdriver not included
Page 5 of 9
Page 6
STEP 7:
2
14
STEP 8:
Ex6 Jx1
Hardware required.
2
Dx6 Ix4
Px1
Hardware required. Screwdriver not included
Page 6 of 9
Page 7
STEP 9:
12
13
12
STEP 10:
O
Fx12
Hardware required
11
11
Kx4 Ox4
Mx2
O
Hardware required
Page 7 of 9
Page 8
STEP 11:
11
L
11
STEP 12:
Lx1
Hardware required
Hx10 Gx10
Px1
Hardware required. Screwdriver not included
Page 8 of 9
Page 9
STEP 13:
Assembly is complete. The TV Stand is ready to enjoy now !
Page 9 of 9
Loading...