Page 1
Assembly Instruction Sheet
ToolsRequired: Flathead screwdriver, Phillips screwdriver,pliers, wire cutters, wire strippers,electrical tape, safety glasses.
LightSource:
EstimatedAssembly Time:
Preparation:
present.If any parts are missingor damaged, do not attemptto assemble, install, or operatethe fixture. Contact customer servicefor replacement
parts.
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal.
(1)A21 MediumBasebulb 150W Maximum or
(1)Medium Base Vintage Bulb is recommendedbut not supplied.
20-30minutes
Identifyand inspect all parts beforebeginning installation. Check package contentlist and diagrams below toensure all parts are
Package Contents
Mounting Screw
A
x3
Fixture Body
C
x1
Glass
B
Panel
x4
STEP 1 Remove Cage from Socket Assembly-
A. Unlock lock screws on the bottom of the socket assembly and
remove the cage from the socket assembly.
Cage
STEP 2 Install Glass Panels-
A. Insert the Glass Panel (B) into the
cage with beveled edge is outside.
Attach the top edge of the Glass
Panel (B) to the slot in the top of the
cage. Fold tabs in the bottom edge of
the cage to secure Glass Panels (B).
Figure 2
STEP 3 Install the Bulb and Cage-
A. Insert the bulb onto the socket and
screw snugly into place.
B. Place the cage back onto the socket
assembly and secure with previously
removed lock screws. Hand tighten
until snug.
Slot
Cage
Tab
B
Cage
C
Vintage Bulb
Socket Assembly
Lock Screw
Figure 1
Thank you for purchasing a product.
Need assistance with parts or assembly? Call our customer service or visit us
1of2
Figure 3
(recommended
but not Supplied)
Socket
Socket Assembly
Lock Screw
Page 2
STEP 4 - Mark the Location for the 3 Mounting Holes
A. Place the light fixture onto the post and mark the location of the 3
mounting holes on the fixture fitter onto the post with the marking
pen.
Post
Lighting
STEP 8 Attach the fixture to
the Post Mount
A. Place the fixture on the post
-
lining up the mounting holes
on the fixture fitter with the
holes on the post. Use the
Mounting Screws (A) to
attach the fixture to the post.
Fixture
Fitter
Post
Lighting
Mounting
Hole
Fixture
Fitter
Post
STEP 5 M C
EM H
A. Remove the light fixture. Using
STEP 6 Drill Holes-
A. Using the 1/16” bit and drill, drill a pilot hole completely through the
- arking the enter of
ach ounting ole
the center punch and hammer
marking the center of each
mounting hole location that is
marked with the marking pen.
post at each (3) locations marked in step 5 above.
Marking Pen
Mounting
Hole
Figure 4
Center Punch
1/16” bit and drill
Fixture
Fitter
Post
Figure 5
Hammer
Marking
Post
Your fixture is now
assembled and ready
to use. Enjoy!
FINISH: EARTH BLACK
7”
7”
A
Figure 8
Post
Hole
Figure 6
STEP 7 - Wire Connections
A. Use standard wire connectors (not included) to make all wire
connections. Twist connectors until wires are tightly joined together.
Wrap each connection with approved electrical tape and carefully
stuff all the connected wires into the Outlet Box.
White wire
from outlet box
Black wire from
outlet box (or Red)
Bare, or Green
Ground wire
from outlet box
Post
White wire
from fixture
Black wire
from fixture
Ground wire
from fixture
Figure 7
Thank you for purchasing a product.
Need assistance with parts or assembly? Call our customer service or visit us
20.5”
NOTE: ALL DIMENSIONS ARE ROUNDED UP
TO THE NEAREST 1/4"
2of2
Loading...