Page 1
Sectional
IMPORTANT
Carefully remove all the parts from the carton and
place them individually on a soft cloth to prevent
scratches or other damage.
Carefully and strictly follow these assembly instructions
to ensure a completed product as designed.
Do not use power tools above 8 volts to assemble.
Part List
L.
Back
1 pc.
H.
Seat Cushion
1 pc.
Hardware List
M.
Seat
1 pc.
I.
Back Cushion
1 pc.
N.
Back
1 pc.
K.
Back Cushion
1 pc.
E.
Foot
4 pcs.
J.
Clip
6 pcs.
Hex Wrench
1 pc.
Small
Hex Wrench
1 pc.
M6x35
Head Cap Bolt
18 pcs. (+1 extra)
Spring Washer
18 pcs. (+1 extra)
Flat Washer
18 pcs. (+1 extra)
Page 2
Assembly Instructions 2/7
IMPORTANT
Use a soft cloth between these parts and the floor.
Do not use power tools above 8 volts to assemble.
Do not tighten all the bolts until each part is properly assembled.
The unit must be level to work properly. Use the included adjustable levelers to level.
Keep Hex Wrench as the bolts may need to be tightened in the future.
Follow instructions in carton first, then proceed with Step 13.
Corner Unit
STEP 13
Attach Seat (M) to Back (N) with Head Cap Bolts,
Spring Washers and Flat Washers,
tightening bolts only halfway.
M
N
Head Cap Bolt
Spring Washer
Flat Washer
Head Cap Bolt
Spring Washer
Flat Washer
L
STEP 14
Attach Back (L) to unit with
Head Cap Bolts, Spring Washers
and Flat Washers, tightening bolts only halfway.
Page 3
Assembly Instructions /37
STEP 15
Insert Head Cap Bolts, Spring Washers
and Flat Washers into unit, tightening bolts
only halfway.
Tighten all bolts used in Steps 13, 14 and 15.
Head Cap Bolt
Spring Washer
Flat Washer
E
Head Cap Bolt
Spring Washer
Flat Washer
E
E
E
STEP 16
Attach Feet (E) to unit
with Head Cap Bolts,
Spring Washers and Flat Washers.
For a 4 seat sectional, complete Steps 17 and 18.
For a 5 seat sectional, follow instructions in carton, then complete Steps 19 and 20.
For a 6 seat sectional, follow instructions in 2 cartons, then complete Steps 21 and 22.
For a 7 seat sectional, follow instructions in 3 cartons, then complete Steps 23 and 24.
Page 4
Assembly Instructions /47
4 Seat Sectional
STEP 17
Attach left unit, middle unit, corner unit
and right unit with Clips (J).
(See Figure 4)
Left Unit Middle Unit
Right Unit
Figure 4
G
F
G
F
J
J
J
J
Cor
ner Unit
J
J
I
K
G
Toggle
H
Figure 5
F
Figure 6
STEP 18
Turn unit to its upright position.
Attach Seat Cushions (F) to unit by
pushing toggles through weaving in back of unit.
(See Figure 5)
Place Seat Cushion (H) and Back Cushions (I), (K) into position.
Level unit by adjusting the adjustable levelers on bottom of unit.
(See Figure 6)
Page 5
5 Seat Sectional
STEP 19
Assembly Instructions /57
Attach left unit, middle units, corner unit
and right unit with Clips (J).
(See Figure 7)
Figure 7
I
G
G
Right Unit
Middle Unit
Left Unit Middle Unit
K
G
G
J
J
J
J
J
J
Cor
J
J
ner Unit
F
F
H
Toggle
F
F
carton is also needed for this step.
Turn unit to its upright position.
Attach Seat Cushions (F) to unit by
pushing toggles through weaving in back of unit.
Place Seat Cushion (H) and Back Cushions (I), (K) into position.
Figure 8
STEP 20
(See Figure 8)
Figure 9
Level unit by adjusting the adjustable levelers on bottom of unit.
(See Figure 9)
Page 6
Assembly Instructions /67
6 Seat Sectional
STEP 21
Attach left unit, middle units, corner unit
and right unit with Clips (J).
(See Figure 10)
Right Unit
Middle Unit
Figure 10
G
F
G
F
Left Unit Middle Unit Middle Unit
J
J
G
I
K
G
H
F
F
F
G
J
J
J
J
J
J
Corner Unit
Toggle
Figure 11
J
J
Figure 12
STEP 22
Two cartons are also needed for this step.
Turn unit to its upright position.
Attach Seat Cushions (F) to unit by
pushing toggles through weaving in back of unit.
(See Figure 11)
Place Seat Cushion (H) and Back Cushions (I), (K) into position.
Level unit by adjusting the adjustable levelers on bottom of unit.
(See Figure 12)
Page 7
7 Seat Sectional
STEP 23
Assembly Instructions /77
Right Unit
Attach left unit, middle units, corner unit
and right unit with Clips (J).
(See Figure 13)
Left Unit Middle Unit Middle Unit
Figure 13
Middle Unit
Middle Unit
J
J
J
J
J
J
J
J
J
Corner Unit
J
J
J
G
F
G
F
G
F
I
K
G
G
H
G
Toggle
F
F
Figure 14
F
STEP 24
Three
pushing toggles through weaving in back of unit.
cartons are also needed for this step.
Turn unit to its upright position.
Attach Seat Cushions (F) to unit by
(See Figure 14)
Figure 15
Place Seat Cushion (H) and Back Cushions (I), (K) into position.
Level unit by adjusting the adjustable levelers on bottom of unit.
(See Figure 15)
Page 8
CARE INSTRUCTIONS
NEVER
allow liquids to remain on furniture.
Absorption causes parts to warp
and split and finishes to delaminate.
Do not use power tools
above 8 volts to assemble.
PREVENT
CRACKING
Do not place
in direct sunlight.
PREVENT
FADING
NEVER
use glass cleaners on
finished furniture. Ammonia
chemically attacks the finish.
Do not write
directly on surface.
PREVENT
MARKING
Do not place hot
objects on surface.
PREVENT
FINISH DAMAGE
Do not use rubber
based placemats.
PREVENT
DISCOLORING
Do not use commercial
waxes and polishes.
PREVENT
YELLOWING
CLEAN
with a soft cloth moistened
in lukewarm soap and water.
Buff with a dry clean cloth.
We will provide replacements free of charge for missing or damaged parts within 1 year of purchase. Digital
images of the defective parts may be required. If the product was not purchased from an authorized retailer, we are
under no obligation to provide replacement parts. Parts are not available for fully assembled items nor are parts
available for sale.
Loading...