Page 1
IMPORTANT
Carefully remove all the parts from the carton and
place them individually on a soft cloth to prevent
scratches or other damage.
Carefully and strictly follow these assembly instructions
to ensure a completed product as designed.
Do not use power tools above 8 volts to assemble.
Part List
O.
Back
1 pc.
Hardware List
Hex Wrench
1 pc.
E.
Foot
4 pcs.
Small
Hex Wrench
1 pc.
P.
Seat
1 pc.
M6x35
Head Cap Bolt
20 pcs. (+1 extra)
J.
Clip
2 pcs.
Spring Washer
20 pcs. (+1 extra)
D.
Frame
2 pcs.
Flat Washer
20 pcs. (+1 extra)
Page 2
Assembly Instructions 2/5
IMPORTANT
Use a soft cloth between these parts and the floor.
Do not use power tools above 8 volts to assemble.
Do not tighten all the bolts until each part is properly assembled.
The unit must be level to work properly. Use the included adjustable levelers to level.
Keep Hex Wrench as the bolts may need to be tightened in the future.
Middle Unit
STEP 1
Attach Seat (P) to Back (O) with Head Cap Bolts,
Spring Washers and Flat Washers,
tightening bolts only halfway.
(See Figure 1)
P
O
Figure 1
Flat Washer
Spring Washer
Head Cap Bolt
STEP 2
Attach Frame (D) to unit with
Head Cap Bolts, Spring Washers and
Flat Washers, tightening bolts only halfway.
D
Flat Washer
Spring Washer
Head Cap Bolt
Page 3
Assembly Instructions /35
STEP 3
Attach withFrame (D) to unit
Head Cap Bolts, Spring Washers and
Flat Washers, tightening bolts only halfway.
Tighten all bolts used in Steps 1, 2 and 3.
Flat Washer
Spring Washer
Head Cap Bolt
Head Cap Bolt
Spring Washer
Flat Washer
E
D
E
E
E
Figure 2
STEP 4
Attach Feet (E) to unit with Head Cap Bolts,
Spring Washers and Flat Washers.
(See Figure 2)
Page 4
Assembly Instructions /45
For a sofa, follow instructions in carton, then complete Steps 5 and 6.
For a 5, 6 or 7 seat sectional, follow instructions in cartons.
Sofa
STEP 5
Attach left unit, middle unit and right unit with Clips (J).
(See Figure 3)
Left Unit Middle Unit Right Unit
J
J
J
J
Figur
e 3
Page 5
G
Assembly Instructions /55
Toggle
Figure 4
G
G
Toggle
STEP 6
Three
Turn unit to its upright position.
cartons are also needed for this step.
F
F
F
Figure 5
Attach Seat Cushions (F) to unit by pushing toggles through weaving in back of unit.
(See Figure 4)
Place Back Cushions (G) into position.
Level unit by adjusting the adjustable levelers on bottom of unit.
(See Figure 5)
Page 6
CARE INSTRUCTIONS
NEVER
allow liquids to remain on furniture.
Absorption causes parts to warp
and split and finishes to delaminate.
Do not use power tools
above 8 volts to assemble.
PREVENT
CRACKING
Do not place
in direct sunlight.
PREVENT
FADING
NEVER
use glass cleaners on
finished furniture. Ammonia
chemically attacks the finish.
Do not write
directly on surface.
PREVENT
MARKING
Do not place hot
objects on surface.
PREVENT
FINISH DAMAGE
Do not use rubber
based placemats.
PREVENT
DISCOLORING
Do not use commercial
waxes and polishes.
PREVENT
YELLOWING
CLEAN
with a soft cloth moistened
in lukewarm soap and water.
Buff with a dry clean cloth.
We will provide replacements free of charge for missing or damaged parts within 1 year of purchase. Digital
images of the defective parts may be required. If the product was not purchased from an authorized retailer, we are
under no obligation to provide replacement parts. Parts are not available for fully assembled items nor are parts
available for sale. Replacements for missing or damaged parts may be requested, contact us.
Page 7
IMPORTANT
Carefully remove all the parts from the carton and
place them individually on a soft cloth to prevent
scratches or other damage.
Carefully and strictly follow these assembly instructions
to ensure a completed product as designed.
Do not use power tools above 8 volts to assemble.
Part List
A.
Back
1 pc.
D.
Frame
1 pcs.
Hardware List
Hex Wrench
1 pc.
Small
Hex Wrench
1 pc.
B.
Seat
1 pc.
E.
Foot
4 pcs.
M6x35
Head Cap Bolt
22 pcs. (+1 extra)
Spring Washer
22 pcs. (+1 extra)
C.
Side
1 pc.
J.
Clip
1 pc.
Flat Washer
22 pcs. (+1 extra)
Two cartons are needed for assembly.
Page 8
Assembly Instructions 2/7
IMPORTANT
Use a soft cloth between these parts and the floor.
Do not use power tools above 8 volts to assemble.
Do not tighten all the bolts until each part is properly assembled.
The unit must be level to work properly. Use the included adjustable levelers to level.
Keep Hex Wrench as the bolts may need to be tightened in the future.
Left Unit
STEP 1
Attach Seat (B) to Back (A) with Head Cap Bolts,
Spring Washers and Flat Washers,
tightening bolts only halfway.
(See Figure 1)
A
Figure 1
B
Flat Washer
Spring Washer
Head Cap Bolt
STEP 2
Attach to Side (C) withunit
Head Cap Bolts, Spring Washers and
Flat Washers, tightening bolts only halfway.
(See Figure 2)
Head Cap Bolt
Spring Washer
Flat Washer
C
Figure 2
Page 9
Assembly Instructions /37
STEP 3
Attach withFrame (D) to unit
Head Cap Bolts, Spring Washers and
Flat Washers, tightening bolts only halfway.
Tighten all bolts used in Steps 1, 2 and 3.
Flat Washer
Spring Washer
Head Cap Bolt
E
E
E
D
Head Cap Bolt
Spring Washer
Flat Washer
E
Figure 3
STEP 4
Attach Feet (E) to unit
with Head Cap Bolts,
Spring Washers and Flat Washers.
(See Figure 3)
Page 10
Assembly Instructions /47
Right Unit
STEP 5
Attach Seat (B) to Back (A) with Head Cap Bolts,
Spring Washers and Flat Washers,
tightening bolts only halfway.
A
B
Flat Washer
Spring Washer
Head Cap Bolt
Head Cap Bolt
Spring Washer
Flat Washer
STEP 6
Attach to Side (C) withunit
Head Cap Bolts, Spring Washers and
Flat Washers, tightening bolts only halfway.
C
Page 11
Assembly Instructions /57
STEP 7
Attach withFrame (D) to unit
Head Cap Bolts, Spring Washers and
Flat Washers, tightening bolts only halfway.
Tighten all bolts used in Steps , 6 and 7.5
Head Cap Bolt
Spring Washer
Flat Washer
E
D
Flat Washer
Spring Washer
Head Cap Bolt
E
E
E
STEP 8
Attach Feet (E) to unit
with Head Cap Bolts,
Spring Washers and Flat Washers.
Page 12
Assembly Instructions 6/7
For a loveseat, complete Steps 9 and 10.
For a sofa, follow instructions in carton.
Loveseat
STEP 9
Attach left unit and right unit with Clips (J).
(See Figure 4)
Left Unit Right Unit
J
J
Figur
e 4
Page 13
G
Assembly Instructions /77
Toggle
Figure 5
G
Toggle
F
STEP 10
T
wo cartons are also needed for this step.
Turn unit to its upright position.
F
Figure 6
Attach Seat Cushions (F) to unit by pushing toggles through weaving in back of unit.
(See Figure 5)
Place Back Cushions (G) into position.
Level unit by adjusting the adjustable levelers on bottom of unit.
(See Figure 6)
Page 14
CARE INSTRUCTIONS
NEVER
allow liquids to remain on furniture.
Absorption causes parts to warp
and split and finishes to delaminate.
Do not use power tools
above 8 volts to assemble.
PREVENT
CRACKING
Do not place
in direct sunlight.
PREVENT
FADING
NEVER
use glass cleaners on
finished furniture. Ammonia
chemically attacks the finish.
Do not write
directly on surface.
PREVENT
MARKING
Do not place hot
objects on surface.
PREVENT
FINISH DAMAGE
Do not use rubber
based placemats.
PREVENT
DISCOLORING
Do not use commercial
waxes and polishes.
PREVENT
YELLOWING
CLEAN
with a soft cloth moistened
in lukewarm soap and water.
Buff with a dry clean cloth.
We will provide replacements free of charge for missing or damaged parts within 1 year of purchase. Digital
images of the defective parts may be required. If the product was not purchased from an authorized retailer, we are
under no obligation to provide replacement parts. Parts are not available for fully assembled items nor are parts
available for sale. Replacements for missing or damaged parts may be requested, contact us.
Page 15
IMPORTANT
Carefully remove all the parts from the carton and
place them individually on a soft cloth to prevent
scratches or other damage.
Carefully and strictly follow these assembly instructions
to ensure a completed product as designed.
Part List
F.
Seat Cushion
1 pc.
Care Instructions
Keep cushions free of natural debris.
Tip and angle cushions after use.
Store cushions inside when not in use.
Allow a minimum of 24 hours for wet cushions to air dry.
Never use a hairdryer on cushions.
Never put cushions in a clothes dryer.
G.
Back Cushion
1 pc.
Loading...