Page 1
Before you start, here are some helpful advice:
1.We suggest you spend a short time reading through this leaflet and then follow the simple step-by-step
instructions.
2. it is assembled by two adults, on a carpeted or
Owing to the size and weight of the TV Stand, we recommend that
padded area, in the room that it is intended for. Approximate assembly time: 70 minutes.
3.Please do not use any tools other than those provided or recommended in these instructions.
4.Please do not throw away any of the packaging or instructions until you have checked all the components and
hardware and the furniture is fully assembled.
5.Assemble all components loosely until advised to tighten. Depending on use, it may be necessary to tighten the
components from time to time, so please save the tools that have
6.Please keep all pieces out of reach of children.
Hardware :
A)
Cambolt/Metal
Camlock/Metal
B)
C)
Dowel/Wood
been provided.
Screw/Metal
D)
Hex/Allen Key/Metal
E)
x 16
x 4
x 10
x 8
Ø 15 mm
Pin Sliding Bottom/Plastic
G)
Ø 8 x 16 mm
L)
Q)
Ø 6 x 35 mm
F)
Pin Sliding Top/Plastic
Ø 8 x 19 mm
Screw/Metal Screw/Metal
K)
M 6.4 x 14 mm M 12 x 45 mm
P)
Screw Cup/Plastic Stoper/Plastic
Ø 15 mm 40 x 14 x 8mm
x 16
x 4
x 8
Ø 8 x 30 mm
H)
Grommet Cover / Plastic
Wall Plug/Plastic
M)
5002
Bumper /Silicon
R)
Ø 8 mm
x 28
M 7 x 50 mm
Short Bracket / Aluminium
I)
x 2
Wall Mounted Bolt/Metal Plastic
N)
x 8
S)
x 1x 2
Screwdriver (Not Include)
L 4
x 16
Long Bracket /Aluminium
J)
x 5
Shelf Pin/Metal
O)
Ø 5 x 15 mm
x 2
x 1
x 1
x 1
x 4
Page 1 of 10
Page 2
Components:
Top Board x1
1 2 3
Center Board 1 x1 Center Board 1 x2
5
Back Board x1
9
Bottom Board x1 Side Board Left x1 Side Board Right x1
6
Adjustable Shelf x1
7
4
Frame Door x2
8
Page 2 of 10
Page 3
STEP 1:
E
Hardware required.
Screwdriver not included
Ax12 Cx12 Ex1 Ix5 Kx10 Sx1
STEP 2:
Ax4 Cx16 Sx1
Hardware required.
Screwdriver not included
Page 3 of 10
Page 4
STEP 3:
Bx4 Sx1
STEP 4:
BACK VIEW
Bx4 Hx1 Px4
Sx1
Ha
rdware required.
Screwdriver not included
Page 4 of 10
Page 5
STEP 5:
Bx4
STEP 6:
Sx1
Hardware required.
Screwdriver not included
Bx4 Px4 Sx1
Hardware required.
Screwdriver not included
Page 5 of 10
Page 6
STEP 7:
Dx12 E
STEP 8:
Hardware required.
Dx4 E Hx1
rdware required.
Ha
Page 6 of 10
Page 7
STEP 9:
Determine your desired (Y)
height, then subtract by 127 mm.
This is the drill holes height from
the floor (Z).
127
( Y )
( Z )
STEP 10:
Please use minimum 1 hole from each hole group to apply the wall plug
and screw. Use additional holes when necessary.
* Long Bracket
Different wall materials require unique wall fasteners.
The wall plugs (M) and screws (L) are designed for fixing to concrete walls only.
Please consult your local hardware store to ensure you are using the correct
hardware for your wall type.
J
L M
Page 7 of 10
Page 8
STEP 11:
J
L
Use Waterpass to ensure the drill position
STEP 12:
Jx1 Lx5 Mx5
Sx1
Hardware required.
Screwdriver not included
Nx2 Sx1
Hardware required.
Screwdriver not included
Page 8 of 10
Page 9
STEP 13:
Ox4
STEP 14:
Hardware required.
8
8
Fx4 Gx4 Qx2
Hardware required.
Page 9 of 10
Page 10
STEP 15:
Q
Rx1
STEP 16:
R
Q
Hardware required.
Assembly is complete. The TV Stand is ready to enjoy now !
Page 10 of 10
Loading...