Page 1
ASSEMBLY AND INSTALLATION
INSTRUCTIONS
H0190
TO AVOID RISK OF ELECTRICAL SHOCK, BE SURE TO SHUT OFF
WARNING:
NOTES: 1. Before installing, consult local electrical codes for wiring and grounding requirements.
2. READ AND SAVE THESE INSTRUCTIONS.
Hardware Package (included):
POWER WHILE INSTALLING OR SERVICING THIS FIXTURE.
Mounting Plate (A)
Bolt Nut (G)
Green Grounding
Screw (B)
Loop Lock (H) Washer (I) Hex Nut (J)
Mounting Screw (C) Lock Nut (E) Wire
Fixture Mounting
Screw (D)
Suction Cap (K)
Installation Steps
Turn off the power at fuse or circuit box.
1. Thread two fixture mounting screws to the mounting plate, and secure them with
two lock nuts. Adjust the length of the fixture mounting screws if necessary.
2. Attach the mounting plate to outlet box by using two mounting screws.
3. Screw the tubes onto the coupling of the main fixture. (See Fig.1)
4. Take two loop locks, open the locking tube, and then hook it onto the loop of the
tube and the loop of hanger. Close back the locking tube of the loop lock.
5. There are (8) 12" L rods, (2) 6" L rods, and (2) 3" L rods are attached in
the hardware package, choose the desired installation height you need. Then
thread the fixture wires and fixture grounding wire through the rods and threaded
pipes as shown in the graph.
Note: Length adjustable from 28-1/8" to 85-1/8". Use fewer rods if shorter length is desired.
Fig. 1
Connector (F)
Tube
Coupling
Main Fixture
6. Screw all rods together until securely by using the threaded pipes, and then lock to the stems of hunger securely.
7. Place the canopy over the rods, making sure the threaded pipes feed through the holes of canopy, then screw canopy with two flat
washers, washers and hex nuts.
8. Cut any excess fixture wires and fixture grounding wire. Slit the two fixture wires apart in 5 inches. Peel off insulation of the two wires
in 5/8 inch.
9. Pull out the house supply wires and the house grounding wire from the outlet box. Make wire connections using the wire connectors:
--- The smooth wire (marked) from the fixture to the black wire from the power source.
--- The ridged wire (unmarked) from the fixture to the white wire from the power source.
--- Attach the fixture grounding wire to the mounting plate with the green grounding screw. Then connect it to the house grounding
wire with a wire connector.
Carefully put the wires back into the outlet box.
10. Raise the canopy against the ceiling, with the fixture mounting screws located on the mounting plate protruding from
the holes on the canopy, secure it with two bolt nuts.
11. Attach the glass shades onto the glass holders, then secure them with the metal pads and socket rings.
12. Install 6 x 60W max medium base bulbs (not included) to the sockets.
211019
Page 2
13. Install bottom bulbs (Included).
a. Attach the suction cap to the top surface of the bulb lens.
b. Insert and twist the bulb (LED GU10 BASE ONLY) into the socket of the lamp holder using the suction cap.
c. Remove the suction cap from the bulb lens by pulling the knob of the suction cap.
Note: Do not discard the suction cap, it will be needed when replacing the bulb.
Turn on the power at fuse or circuit box.
14. Choose a mode by turn the 3 - way switch on the side of the fixture.
a. Turn the 3 - way switch clockwise, the bottom light will turn off and the side lights will brighten.
b. Turn the 3 - way switch clockwise again, the bottom light will brighten and the side lights will turn off.
c. Turn the 3 - way switch clockwise again, all lights will brighten.
Outlet Box
Housing Grounding Wire
wire connector (F)
Fixture Mounting Screw (D)
Mounting Plate (A)
Green Grounding Screw (B)
Mounting Screw (C)
Lock Nut (E)
Canopy (K)
Bolt Nut (G)
8 X 12" Rod
2 X 6" Rod
Fixture Wire
Fixture Grounding Wire
Hex Nut (J)
Washer (I)
Flat Washer
Threaded Pipe
Figure.1
Loop lock
Twist the locking
tube to open or
close loop lock
Socket Ring
Glass Shade
Bulb Type A
Max.60W
(not included)
2 X 3" Rod
hanger
Loop
Loop Lock (H)
Tube
Metal Pad
Main Fixture
Socket
3-Way Switch
LED GU10 Bulb
Max.5W (included)
Suction Cap (K)
Knob
211019
Page 3
The following parts are available for re-order if damaged or missing.
Spare Parts List:
Mounting Plate (A)
Wire connector (F)
12”Rod 4644RR
LED GU10 Bulb Max.5W
8082HL
Green Grounding
Screw (B)
Bolt Nut (G)
Mounting Screw (C) Lock Nut (E)
Assembly Kit 5772MM
6”Rod 4645RR
Fixture Mounting Screw (D)
3”Rod 4646RR
Glass Shade 9916CS
B
C
A: 38"
B: 14"
C:31"~85"
A
211019
Loading...