Page 1
Description : COCKTAIL TABLEProduct
Size : 48"x 28"x 18"H
P. 1/4
Wood Furniture Maintenance:
- Always dust, wipe, and clean with the grain of the wood.
- Dust with a soft cloth. Dust will scratch the furniture surface if
not removed properly.
- Use the same type of polish consistently as interchanging oil based and wax-based polishes will cause a build-up and result
in a foggy or cloudy appearance.
- If a polished surface becomes foggy, rub it with a cloth dipped
in a solution of one tablespoon vinegar to one quart of water.
Rub softly with the grain until the surface is completely dry.
- Soap and water are not advisable for wood surfaces. Water
can penetrate the finish and raise the grain on wood, causing
damage.
- Remember to change dusting cloths frequently as dirty cloths
may scratch your furniture's surface.
The Enemies of Wood:
- Moisture is wood's worst enemy. Liquid spills should be gently
wiped up immediately. Coasters should be used under all
beverages.
- Do not allow rubber or vinyl materials to lie on the furniture.
Chemicals in rubber may leave a stain. Put a strip of felt or
leather under accessories that have rubber or vinyl.
- Heat creates a chemical change in the furniture's finish, which
results in a white spot. Use protective pads under hot dishes,
appliances, etc.
- Sunlight's ultraviolet rays can damage the finish of furniture.
Do not place furniture directly against a heater or radiator and
do not place in the path of hot streams of air from central heating.
This will cause extreme localized drying of the wood.
High Gloss Resin Table Maintenance:
- Resin tabletops have approximately 1/8" of a resin coat on the
top face of the table, which will resist ice, water, wine, liquor, food,
cleaning fluids, and warm or hot liquids; however, cups, glasses,
etc. containing hot liquids should not be left on the table without a
coaster for protection.
- Resin tabletops will scratch just the same as any other glossy
surface and basic precautions should be taken.
- For lasting shine, the resin table should be waxed with a car wax
that does not contain silicon. Maintaining this wax build-up will
result in a high gloss shine.
- When wiping down the table, a soft, clean rag should be used.
Do not use a heavy paper.
Granite Top Maintenance:
The surface of the granite on your table has been polished or sealed to create a
generally non-porous surface. The stone has many natural characteristics
including: veining, hairline cracks, and color variations - which make up the stone's
beauty.
To maintain the beauty of your granite:
- Protect surfaces from scratching, staining and etching by:
* Keeping them free of debris or sharp objects
* Wiping up spills immediately
* Avoiding contact with chemicals (particularly acid-based materials)
- Clean with pH neutral products or those especially formulated for use on stone.
- It is not recommended to use a water-based solvent for dark granite as it will
remove the polish from the surface.
absorbed into the stone.
- After a period of use, apply a penetrating sealer to prevent contaminants from being
- Remove stains with special absorbent poultices formulated for use on stone.
- Renew the surface on polished granite (granite with a hight gloss surface ) by buffing
with special stone polish , powder or cream .
Do not use granite polish on granite with a matte finish, which has been honed
rather than polished. (Penetrating sealer may be used on both polished and honed
granite.)
Marble Top Maintenance:
Marble may be stone, but it is porous stone and can stain easily. Treating marble
surfaces the same as wood surfaces is a great rule of thumb.
- It is recommended to seal the tops on a regular basis (every 6 to 12 months).
A good quality stone sealer can be purchased from any tiles/stone store or any
homecare store and should be applied according to the manufacturer's
recommendation.
- When sealed properly, marble tops can be used indoors and outdoors and can
withstand any weather conditions except internal freezing. Snow or freezing rain
will penetrate the table and cause cracks.
Caring for the Fabric on Upholstered Furniture:
- Frequent vacuuming of the entire upholstered area will prevent dust from settling
into the fibers.
- Professional cleaning is always recommended for all upholstered pieces.
- Always pre-test a small area of fabric in an inconspicuous area when cleaning
before proceeding.
- Do not use cleaning products containing brightening agents.
Page 2
P. 2/4
MADE IN VIETNAM
ASSEMBLY INSTRUCTIONS
STEP 1: Align the Leg Frames (B) together with Upper Stretcher (C) and Lower Stretcher (D) as
picture shown. Insert I-nut (1) and secure well by Allen Key (5).
STEP 2: Place the Table Top (A) on the floor with a piece of cloth or carpet to prevent finish from
scratching. Attach the base in Step 1 to the top by using Flat Washer (4), Lock Washer (3) and Allen
Secure well by Wrench
Bolt (2).
(6). Assembly product is now completed.
Page 3
PARTS LIST
P. 3/4
HARDWARE LIST
Allen Bolt
Allen Key
Straight Allen Key
MADE IN VIETNAM
Page 4
MADE IN VIETNAM
PRODUCT DETAILS
TOP
LEGS
PRODUCT SIZE
CARTON SIZE
NET WEIGHT
GROSS WEIGHT
CU.FT.
ACACIA WOOD
METAL
48" x 28" x 18"H
50.98''x31.89''x8.26''
48.4 LBS
61.6 LBS
7.77/1PC'
P. 4/4
PLZ100CLF
LEG FRAME
COMPLETE HARDWARE
UPPER STRETCHER
PLZ100CUST
PLZ100CLST
LOWER STRETCHER
PLZ100CLEV
LEVELER
Loading...