Page 1
Page 1 of 4
SOFA /CHAIR
SOFA/CHAIR.
Before you start, here are some helpful advice:
1. We suggest you spend a short time reading through this leaflet and then follow the simple step-by-step
instructions.
2. Owing to the size and weight of the sofa/chair, we recommend that it is assembled by two adults, on a
carpeted or padded area, in the room that it is intended for. Approximate assembly time: 20 minutes.
3. Please do not use any tools other than those provided or recommended in these instructions.
4. Please do not throw away any of the packaging or the instruction until you have checked all the components
and hardware and the furniture is fully assembled. Please ensure that the packaging is disposed of in a safe
and environmentally friendly way.
5. Assemble all components loosely until advised to tighten. Depending on use, it may be necessary to tighten
the components from time to time, so please save the tools that have been provided.
6. Please keep all fitting out of reach of children.
Thank you for purchasing the
Hardware:
Components:
A. Bolt M8x 65mm x 8
B. Bolt M8x 55mm x 4
C. Spring Washer x 12
D. Flat Washer x 12
E. Allen Wrench x1
1 Sofa Body x1 2L/2R Front Leg x 2 3 Front leg stretcher x 2
4L/4R Back Leg x2 5 Back leg stretcher x2
Page 2
Page 2 of 4
SOFA/ CHAIR
STEP 1:
Please put Sofa Body (1) on a carpeted or padded surface.
Open the zipper on the bottom of the Sofa Body (1) and take out the 2 pieces of Front Legs (2L/2R) &
Front leg stretcher (3) and 2 pieces of Back Legs (4L/4R) & Back leg stretcher (5) and hardware from the
legs box.
STEP 2:
Attach 1 piece of Front Leg (2L) to the bottom of Sofa Body (1) by using 2 pieces of Bolts (A) with 2 pieces of
Spring Washer (C) and 2 pieces of Flat Washer (D) as shown.
Tighten Bolts (A) by using Allen Wrench (E) as shown.
Hardware & Tools required
Page 3
Page 3 of 4
A
x 2
SOFA/ CHAIR
STEP 3:
Insert the smaller end of Front Leg stretcher (3) into the hole of
Front Leg （2L） and attach the other end of
Front Leg stretcher (3) to the bottom of Sofa Body (1) by using 1 piece of Bolts (B) with 1 piece of Spring
Washer (C) and 1 piece of Flat Washer (D) as shown.
Hardware & Tools required
STEP 4:
Attach 1 piece of Front Leg (2R) & Front Leg stretcher (3) to the bottom of Sofa Body (1) by using 2 pieces of
Bolts (A) and 1 piece of Bolt (B) with 3 pieces of Spring Washer (C) and 3 pieces of Flat Washer (D) as shown.
Tighten Bolts by using Allen Wrench (E) as shown
.
C
B
x 3
x 1
E
x 1
D
x 3
Hardware & Tools required
Page 4
Page 4 of 4
1
B
x 2
A
x 6
x 4
D
x 1
E
C
x 6
SOFA/ CHAIR
STEP 5:
Repeat the same steps for other pieces of Leg (4R/4L) & Back Leg stretcher (5).
Tighten Bolts by using Allen Wrench (E) as shown
Hardware & Tools required
STEP 6:
Close the zipper on the bottom of the Sofa Body (1).
Carefully turn over the assembled Sofa Body (1) and Legs (2) & (4) from step 5 by two adults as shown to avoid
leg crack.
Assembly is complete. Your Sofa/Chair is ready to be used now!
Loading...