Mercury Row W003191060 Assembly Instructions

P.1

All rights reserved.

Assembly Instructions

P.2

General Assembly Guidelines

I. Ensure that all parts and hardware are available before beginning assembly.

II. Follow each step carefully to ensure the proper assembly of this product.

III. Two people are recommended for ease in the assembly of this product.

IV. The three main types of hardware used to assemble this product are: wood

dowels, screws and bolts.
V. The provided glue is to secure wood dowels in place. When first inserting dowels,

locate the appropriate hole for the dowel, place a small amount of glue in the hole
and insert the dowel. Wipe away excess glue immediately.

21

In future assembly steps when dowels are necessary to attach assembly parts

together, place a small amount of glue on the end of the dowel before attaching

parts together. Wipe away excess glue immediately.

VI. A Phillips head screwdriver is required for the assembly of this product .

VII. Power tools should not be used to assemble this product.

VIII. Drill may be needed for securing product to wall.

Parts List

P.3

All rights reserved.

1

5

6

4

6

3

7

7

8

8

2

9

9

9

9

9

13

12

10

14

11

15

16

X 2

Hardware List

P.4

A
B
C
D
E
F

H
J
K
L
M

Ø8x30mm
Ø6x35mm
Ø15x11mm
Ø15x9.5mm Cam lock

Ø6x50mm

M 4G

Ø6x12mm

Ø4x22mm Handle Bolt
Ø4x32mm Screw 10

Wooden dowel
Cam bolt
Cam lock

Sticker
Screw

Hex Key
Bolt

Handle

Bolt

24
24
16

8

24

6
1

20

1
2

2

pcs
pcs
pcs

pcs

pcs
pcs

pc
pcs

pc
pcs

pcs

pcs

N
P

Q
R
S
T
U
V
W
X
Y
Z

Ø3x17mm

Ø3x12mm

Ø4x25mm

Ø4x12mm

Plastic wedge
Screw

Pulley
Pulley
Screw

Shelf support pin
Velcro strap
Screw

Nut
Screw

Glue tube 1

Drawer slider

* Note: This piece comes preassembled for
shipping purposes and must be disassembled
to complete the desk assembly.

8
8

2
2

40

8

2
2

2
2

2

pcs
pcs

pcs
pcs

pcs
pcs

pcs
pcs

pcs
pcs

pc
Set

Philips head screwdriver required for assembly

(not included)

The hardware quantities listed above are required for proper assembly.

Some extra hardware may also have been included.

P.5

Step 1

All rights reserved.

Pick up the slider arm (Z) and separate the slide Runner for the following Steps. Extend
the Slide .Runner all the way forward,press the plastic release lever of the slider arm up
and pull the Slide Runner Complete out .

Slider arm

Slider arm

Slider bracket

Z

Slider bracket

Z

P.6

Step 2

All rights reserved.

Using screw (S) attach slider bracket (Z) to parts (11,12) with Philips head screwdriver as per
diagram.

S

S

S

11

S

S

12

Z

S

Z

Step 3

P.7

All rights reserved.

Using screw (S) attach slider arm (Z) to parts (3,4,5) with Philips head screwdriver as per diagram.

S

S

Z Z Z

S

3

S

S

5

S

Z

S

S

4 4

S

S

S

Step 4

P.8

Insert wooden dowel (A) into parts (3,4,5), then secure cam bolt (B) into parts (3,4,5) with Philips
head screwdriver as per diagram.

A

A

B

B

3

A

A

A

A

B

B

B

5

A

A

4 4

A

B

A

A

B

A

P.9

Step 5

Insert wooden dowel (A) into parts (7,16), then secure cam bolt (B) into parts (1,15) with Philips
head screwdriver as per diagram.

B

B

B

A

B

A

B

B

B

B

15 x 2pcs

1

A

A

B

7 x 2pcs

A

16 x 2pcs

A

P.10

Step 6

Using cam lock(C) secure part (7) to parts (4,5) with Philips head screwdriver as per diagram.

Finished edge

21 3

C

5

7

C

Finished edge

C

4

7

C

Step 7

P.11

All rights reserved.

Using cam lock(C) secure part (7) to parts (3,4) with Philips head screwdriver as per diagram.

3

21 3

C

7

C

C

4

C

7

Step 8

P.12

All rights reserved.

Using screw (F) attach part (2) into parts (3,4,5) with hex key (G) as per diagram.

5

F

4

F

3

F

2

3

F

F

G

2

F

Step 9

P.13

All rights reserved.

Using bolt (H) attach part (9) to part (2) with hex key (G) as per diagram.

H

H

H

9

H

9

H

H

H

H

2

9

9

H

H

G

9

Step 10

P.14

Put part (6) as per diagram.

3

6

6

5

4

Step 11

P.15

Using cam lock (C) secure part (1) into parts (3,4,5) with Philips head screwdriver as per diagram.

21 3

1

C

C

C

5

C

C

C

3

4

Step 12

P.16

All rights reserved.

Using screw (P) secure plastic wedge (N) to part (6) with Philips head screwdriver as per diagram.

N

6

6

P

N

Step 13

P.17

All rights reserved.

Using screw (L) attach parts (11,12) to part (13) with Philips head screwdriver as per diagram.

X 2

11

12

13

L

L

L

L

Step 14

P.18

Put part (14) as per diagram.

X 2

12

14

11

13

Step 15

P.19

All rights reserved.

Using screw (L) attach part (13) to part (16) with Philips head screwdriver as per diagram.

X 2

16

13

L

Step 16

P.20

All rights reserved.

Using cam lock (D) attach part (15) to parts (11,12) and cam lock (C) attach part (15) to part (16)
with Philips head screwdriver as per diagram.

21 3

D

D

D

D

11

15

C

12

16

X 2

Step 17

P.21

Place sticker (E) cover the holes as per diagram.

E

E

E

E

E

E

E

E

E

Step 18

P.22

Insert shelf support pin (T) into parts (3,4,5) as per diagram. Make sure you place the four shelf
support pins (T) in the same level. So the shelf is not titled .Put part (8) into unit as per diagram.
Tilt and rest the adjustable shelf (8) onto the shelf support pins .

5

4

T

3

T

T

T

T

8

T

T

T

T

8

8

Step 19

P.23

All rights reserved.

Using screw (S) attach Pulley (R,Q) to part (10) ,then using handle bolt (K) secure handle (J) to part
(10) with Philips head screwdriver as per diagram.

S

Q

S

S

R

10

M

10

S

R

K

K

J

Q

M

Step 20

P.24

Pick up the door (10), and fit the pulley (R) over the slider rails on the bottom panel (2) ,then place
the pulley (Q) into top panel (1) , till it click into pulley (R) as per diagram.

R

1

10

2

2

1

Q

10

10

Q

Slider bracket

Step 21

P.25

All rights reserved.

Insert the assembled drawers into the unit frame, extend the Ball Bearing Slide Tracks (Z) on the
pedestal Side Panel all the way forward .Then align the Slide Runners on the assembled drawers
with the Slide Tracks and push the drawer carefully inside until it stops. Note : if the drawer does
not go in smoothly, please take it out and repeat the step. If you need to remove the drawer, please
pull the drawer all the way out, press or lift the plastic release lever and pull out the drawer and
then re-assembled the drawer until it was going in smoothly .

Slider arm

OR

z

Slider bracket

Step 22

P.26

All rights reserved.

Insert the assembled drawers into the unit frame, extend the Ball Bearing Slide Tracks (Z) on the
pedestal Side Panel all the way forward .Then align the Slide Runners on the assembled drawers
with the Slide Tracks and push the drawer carefully inside until it stops. Note : if the drawer does
not go in smoothly, please take it out and repeat the step. If you need to remove the drawer, please
pull the drawer all the way out, press or lift the plastic release lever and pull out the drawer and
then re-assembled the drawer until it was going in smoothly .

Slider arm

OR

z

Step 23

P.27

All rights reserved.

Using screw (X) attach Velcro strap (U) into part (1) with Philips head screwdriver as per diagram.

U

X

1

U

X

P.28

21 3

Using screw (V) attach Velcro strap (U) into Nut (W) to wall with Philips head screwdriver as per
diagram.

WARNING

Serious or fatal injuries can occur from furniture tipping over. To prevent the furniture from tipping over we recommend
that it is permanently fixed to the wall. Wall anchor and hardware are included with this product. Please make sure

hardware is suitable for your walls before installing, as different wall materials may require different types of anchors.

Wall

W

U

V

Step 25

P.29

All rights reserved.

Position the assembled unit at the desired location ,if necessary adjust the floor leveler at the
bottom of the support leg to level the unit .

Step 26

P.30

All rights reserved.

Final Assembly