Page 1
ASSEMBLY INSTRUCTIONS
Before you begin, please follow assembly instructions carefully, then follow them step by step.
Read instruction carefully . See Furniture Parts list and Hardware List for guidance . Be sure you have all parts before you start assembling .
Place and assemble furniture on a clean flat soft surface , such as carpet or rug to pervent being scratched .
PART LIST
TOP PANEL 1 PC
1
BOTTOM PANEL
2
SIDE PANEL (L)
3
SIDE PANEL (R)
4
CENTER PANEL
5
BACK PANEL
6
SHELF PANEL (L)
7
SHELF PANEL (R)
8
DOOR PANEL (L)
9
DOOR PANEL (R)
10
SELF-PREPARED TOOLS: Tools below are NOT included in package.
SCREWDRIVER
POWER DRILL
HAMMER
QTY
1 PC
1 PC
1 PC
1 PC
1 PC
4 PCS
4 PCS
1 PC
2 PCS
HARDWARE
MINI FIX
A
M8 X 30MM WOOD DOWEL
B
M6 X 5OMM
C
CSK CAP WOOD SCREW
M4 X 25MM C.B SCREW
D
M3.5 X 16MM C.B SCREW
E
ALLEN KEY M4
F
5/8 NAIL
G
5/8 HINGES
H
METAL SHELF SUPPORT
I
PVC HANDLE 108-160
J
PVC SQUARE LEG 5038
K
TIPPING PACK
L
A1
L1
L2
A2
A3
6 SETS
12 PCS
6 PCS
6 PCS
40 PCS
1 PC
35 PCS
6 PCS
32 PCS
1
3 PCS
4 PCS
L3
L5
L4
2 SETS
3
5
7
7
6
8
8
4
J
9
Reminder:
Please ensure that all surfaces and edges with colours/laminations are facing forward/outward.
10
7
10
7
2
8
8
K
Page 2
ASSEMBLY INSTRUCTIONS
STEP 1 STEP 2
- Insert hardware A1 onto panel (3), (4) and (5).
(Repeat 6 times.)
- Insert hardware
(Repeat 4 times.)
- Insert hardware
(Repeat 12 times.)
A2 onto panel (1).
B onto panel (3), (4) and (5).
A2
x4
A1
ROTATE
SCREWDRIVER
REQUIRED
B
- Attach panel (3), (4) and (5) to panel (1).
- Insert all hardware A2 into A1.
- Rotate all A1 until tight.
- Apply A3 onto all A1.
(Repeat 6 times.)
x12
x6
PRESS
4
5
* Ensure the arrows on hardware A1 point towards mounting positions.
STEP 3 STEP 4
Connect panel (2) to panel (3), (4) and (5) by using hardware C and F.
(Repeat 6 times.)
1
3
PRESS
* In this step hardware A1, A2 and B are pre-inserted.
- Fix hardware K into panel (2) with hardware E.
( Repeat 4 times for each hardware.)
- Cover back the hardware
( Repeat 4 Times )
SCREWDRIVER
REQUIRED
OR
HARDWARE
F
4
5
1
x6
3
Section View
A1
A2
ROTATE
A3
x6
PRESS
SCREWDRIVER
REQUIRED
K.
C
2
x6
ROTATE
F
* In this step hardware B are pre-inserted.
K
K
ROTATE
PRESS
x16
x4
4
1
5
3
2
4
5
1
E
3
K
PAGE: /4
2
Page 3
ASSEMBLY INSTRUCTIONS
STEP 5 STEP 6
Assemble panel (6) to entire body with hardware G.
(Repeat 35 times.)
HAMMER
REQUIRED
- Insert hardware I into mounting positions on panel (3), (4) and (5) by hand.
(Repeat 32 times.)
- Assemble the panel
(Repeat 8 times.)
G
x35
10
HIT
SCREWDRIVER
REQUIRED
x32
- Fix hardware H into panel (3), (4) and (5) by using hardware E.
(Repeat 2 times for each hardware.)
- Tighten or loosen the screw to adjust position of panel
(Do only when needed.)
6
3
2
STEP 7 STEP 8
- Fix hardware H onto panel (9) and (10) by using hardware E.
(Repeat 2 times for each hardware.)
- Fix hardware
(Repeat 2 times for each hardware.)
J onto panel (9) and (10) by using hardware D.
H
E
PRESS
H
(7) and (8) into between panel (3), (4) and (5).
1
3
7
7
I
7
7
5
8
8
8
8
2
(9) and (10).
4
SCREWDRIVER
REQUIRED
1
6
3
6
x6
ROTATE
D
x12
ROTATE
J
9
10
J
PAGE: /4
* In this step hardware H have been assembled in panel (9) and (10).
3
ADJUST
H
ADJUST
x12
H
ROTATE
E
9
6
6
10
2
10
4
Page 4
ASSEMBLY INSTRUCTIONS
STEP 9 STEP 10
Assemble hardware L1 into panel (1) and (6)
by using hardware L2.
(Repeat 2 times.)
1
SCREWDRIVER
REQUIRED
- Mark and use the power drill
to drill a hole on the wall.
- Hit hardware
(Repeat 2 times.)
L1
L2
ROTATE
STEP 11 STEP 12
- Assemble hardware L1 to L3 by using hardware L4.
(Repeat 2 times.)
x2
6
3
SCREWDRIVER
REQUIRED
- Connect two of the hardware L1 by using hardware L5.
- Tighten the hardware L5.
(Repeat 2 times.)
L3 into the wall.
POWER
DRILL
REQUIRED
1
L3
HAMMER
REQUIRED
x2
HIT
9
10
10
4
L1
L5
L1
CONNECT
L1
L5
x2
1
1
L3
L4
L1
x2
9
10
10
4
ROTATE
9
10
10
4
x2
L1
PAGE: /4
4
TIGHTEN
Loading...