Page 1
Installation Guide
Pleasegoto our website for product cleaning tips.Go to the selection.
ToolsRequired: Flatheadscrewdriver, Phillipsscrewdriver,pliers,wire cutters,wire strippers,electricaltape, safetyglasses.
LightSource:
FixtureHangingHeight:
EstimatedAssembly Time:
Preparation:
present.Ifany partsare missingordamaged, donot attempttoassemble, install,or operatethefixture. Contactyour originalplaceof purchase.
(4)B10Candelabra Basebulbs 60WMaximum,bulb notincluded.
MinimumHangingHeight is26”, MaximumHangingHeight is74”.
30-45minutes
Identifyandinspect allparts beforebeginninginstallation. Checkpackage contentlistand diagramsbelow toensureall partsare
Care+Maintenance
Note: This CONVERTIBLE fixture can be mounted as chandelier light or semi-flush light. Refer to respective
installation steps for installations.
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal.
Package Contents
Crossbar Assembly
A
x1
C
Fixture Chain
B
x1
Quick Link
x2
Ceiling Canopy
D
x1
Canopy
E
x1
Fixture Loop
F
x1
Center Column
G
x1
Loop
STEP 2A - Install the Canopy Loop
A. Thread the Canopy Loop
Ceiling Canopy (D) and h
until snug.
STEP 3A - Installing the CrossbarAssembly
A. Pass the supply wires from outlet box through the Crossbar
Assembly (A). Attach the Crossbar Assembly (A) to the Outlet Box
with the head of the Green Ground Screw facing you. Secure the
Crossbar Assembly (A) with Outlet Box Screws (not included).
Tighten until snug.
(E) to the
and tighten
E
Figure 2A
D
Glass
H
x4
Fixture Body
I
x1
Assembly Instructions for Chandelier Light:
(Step 1A - Step 8A)
STEP 1A - Install the Fixture Loop and the Center Column
A. Thread the Fixture Loop , the Center Column and the
(I) together as shown. Hand tighten until snug.
Body
(F) (G) Fixture
F
G
I
Figure 1A
Figure 3A
Outlet Box Screws
(not included)
STEP 4A Test Fitting Ceiling Canopy to Crossbar Assembly-
A.
Remove mounting balls from the Crossbar Assembly (A). Fit the
Ceiling Canopy (D)
mounting balls. Note: The should be snug against
the and the mounting balls. If
ceiling
mounting screws on the Crossbar Assembly (A) by unscrewing the
preassembled hex nut and lock washer and then screwing the
mounting screws in or out of the crossbar until the correct length is
achieved. Once the Ceiling Canopy (D) is secure, remove the
mounting ball and .Ceiling Canopy (D)
Mounting Screw
Mounting Ball
to the
Crossbar Assembly (A) and secure with
Fixture Canopy
A
D
Figure 4A
Outlet Box
A
Supply Wires with
Ground Wire
not, adjust the length of the
Hex Nut and
Lock Washer
1of2
Page 2
STEP 5A - Install the Fixture Chain and Ceiling Canopy
STEP 8A - Install Glasses and Bulbs
A. Adjust the Fixture Chain (B) to your desired length by removing
links if needed. Put a cloth over the Fixture Chain (B) to protect the
finish.
B. Pull the supply wires through
the Fixture Chain (B) alternating
links. After the wires are
through the Fixture Chain (B),
pull the supply wires and the
ground wire through the Ceiling Canopy (D).
C. Attach one end of the Fixture Chain (B) to the
Fixture Loop (F) with one Quick Link (C). Lift the
fixture and Fixture Chain (B) up and attach the
other end of the Fixture Chain (B) onto the
Canopy Loop (E) with another Quick Link (C).
The fixture will now hang safely.
D. Cut the wires leaving approximately 8” of wire
extending from the Outlet Box.
Suggested chain length for Ceiling height :
8’ ceiling : use 10links of chain and 2 quick links
9’ ceiling : use 20links of chain and 2 quick links
10’ ceiling : use 30 links of chain and 2 quick
links
STEP 6A - Making the Wire Connections
A. Wrap bare or green ground wire around green ground screw on the
crossbar, no less than 2 inches from the end of the wire. Tighten the
green ground screw.
B. Use standard wire connectors (not included) to make all wire
connections. Twist connectors until wires are tightly joined together.
Wrap each connection with approved electrical tape and carefully
stuff all the connected wires into outlet box.
Note: If the electrical wire is going to be cut shorter than provided
you will need to identify the "L" line wire and the "N" neutral wire
before you cut the excess wire off. One is labeled N and the other
labeled L. To do this separate the "L" line wire and the "N" neutral
wire as far as you need to. Re-label the wire near where you want to
make the cut. Be sure to mark the wire on the side of the fixture and
not on the excess wire being cut and removed.
Supply
Wires and
Ground Wire
Figure 5A
Insert bulb onto socket and screw snugly into place.
A. s s
B. Place the neck of the Glass (H) into the bobeche on the Fixture
Body (I) and secure with lock screws. Hand-tighten until snug.
D
E
C
B
Your fixture is now assembled and ready to use. Enjoy!
Bobeche
Lock Screw
Socket
Bulb(not
Figure 8A
included)
H
Neck
Assembly Instructions for Semi-Flush Light:
(Step 1B)
C
The following parts will not be used in the assembly of the SemiFlush Light fixture. Please set aside these parts.
F
Fixture Chain
B
x1
Quick Link
C
x2
Canopy
E
x1
STEP 1B - Install the Ceiling Canopy and the Center Column
A. Pass supply wires and ground wire through the Center Column (G)
and the Ceiling Canopy (D).
B. Thread the , the Center Column and the
Fixture Body Cut the
wires leaving approximately ” of wire extending from the Ceiling
Canopy (D).
C. Go to Step 3A- Step 4A, Step 6A- Step 8A
installations.
Ceiling Canopy (D) (G)
Loop
(I) together as shown. Hand tighten until snug.
6
(Extra Parts include)
F
to complete
Fixture Loop
x1
White wire
from outlet box
Black wire from
outlet box (or Red)
Bare, or Green
Ground wire
from outlet box
Green Ground Screw
on the Crossbar
STEP 7A Install the Ceiling
Canopy to CrossbarAssembly
A. Carefully tuck all wires into
-
the outlet box and position the
Ceiling Canopy (D) over the
outlet box. Align the holes in
the Ceiling Canopy (D) with
the mounting screws, then
attach the Ceiling Canopy (D)
using the previously removed
mounting balls. Hand tighten
until snug.
supply wire from fixture
identified with the Label “N”
supply wire from fixture
identified with the label “L”
Ground wire
from Fixture
Figure 6A
Mounting
Screw
Mounting Ball
A
D
Figure 7A
D
G
Figure 1B
Supply Wires
and Ground Wire
I
2of2
Loading...