Page 1
ASSEMBLY INSTRUCTION
E181-70 70" TV STAND
Front Frame
A B C D
1PC 1PC 1PC 1PC
Divider Panel
E
3PCS 4PCS 2PCS
Bolt
I F
1/4”x1/2”
Shelf Panel T-Shaped Leg
F
F
Bolt
J
1/4”x1/2”
G
K
Top Panel Bottom PanelBack Frame
Bolt
1/4”x1/2”
H
L
Cross Bar
5PCS
Shelf Pin
2PCS 4PCS 32PCS
M
Metal Plate
12PCS
Allen Wrench
N
F
4MM
1PC
O
This page lists all the contents included in the box.
Please take the time to identify the hardware as
well as the individual components to this product.
As you unpack and prepare for assembly, place
the contents on a carpeted or padded area to
protect them from damage.
Anti-Tipping HW
F
2SETS
16PCS
1
Page 2
***Do not tighten screws & bolts until the entire unit is completely assembled.
Attach the Bolt (J) to the Front Frame (A) by Allen Wrench (N) as shown.
1
A
A
N
X 2
J
2
Attach the Bolt (J) to the Back Frame (B) by Allen Wrench (N) as shown.
N
X 2
J
B
B
2
Page 3
3
Attach the T-Shaped Leg (G) to the Back Frame (B) by using Bolt (K) as shown.
B
G
G
X 2
K
Unfold the Front Frame (A) as shown.
4
G
K
A
3
Page 4
5
Attach the Cross Bar (H) to the Front Frame (A) by using Bolt (K) as shown.
6
H
H
H
K
Attach the Back Frame (B) to the Front Frame (A) and Cross Bar (H) by using Bolt (K) as
shown.
X 5
K
A
H
H
K
H
H
K
X 5
X 4
K
B
H
H
H
A
4
Page 5
7
Place Bottom Panel (D) on Cross Bar (H) as shown.
8
H
H
Insert Metal Plate (M) into the holes on the Front Frame (A) and Back Frame (B) as shown.
D
H
H
B
A
M
D
X 12
5
Page 6
9
Slide the Divider Panel (E) through the Metal Plate (M). Make sure the dividers are facing
correctly as shown.
E
E
E
B
A
D
10
Attach Top Panel (C) to the Front Frame (A) and Back Frame (B) by using Bolt (K) as shown.
X 4
K
C
B
A
6
Page 7
11
Insert Shelf Pin (L) to the holes of Divider Panel (E) and side panels. Then place Shelf
Panel (F) onto the Shelf Pin (L) as shown.
X 8
L
L
F
E
F
E
E
F
F
7
Page 8
12
*NOTE: WE RECOMMEND THAT YOU ATTACH THE PRODUCT TO YOUR WALL
AS A SAFETY PRECAUTION USING ANTI-TIPPING HW (O) AS BELOW
INSTRUCTION.
Attach Mounting Plate to the Back Frame (B) by using Bolt (I), make sure the
Mounting Plate extend DOWNWARD.
Drill 2 holes in your wall approximately 2” (Inches) BELOW the corresponding
positions of Mounting Plate and insert Wall Anchor as shown.
*NOTE: You may need to tap LIGHTLY with a rubber mallet.
Now connect the corresponding Mounting Plate with Connection Strap and tighten as
described before locking in place.
1
C
I
N
B
2
3
4
Wall
Wall
Wall
Wall
O
Cleaning & Care
Treat surface with care. Surface is resistant to scratches but is not scratch resistant. Clean surfaces
with a dry or damp soft cloth. Do not use abrasive cleaners. Hardware may loosen over time.
Periodically check that all connections are tight.
8
Loading...