Label Picture Description QTY
A Left Side Frame 1
B Right Side Frame 1
WARNING: These chairs are intended only for normal use with all four chair
legs on the ground. These consumer chairs have relatively thin legs and are
not designed to be sat in with only two chair legs on the ground (as from
tipping back, forward, or to the side), and such can cause stress and failure
of one or more chair legs. Any misuse of the chair voids any warranties,
express or implied.
Assembly Instructions
Caution : You must read this before you proceed
DINING CHAIR
Part List
Page 1 of 8
C Front Stretcher 1
D Back Stretcher 1
E Top Rest 1
F Cushion Seat 1
Label Picture Description QTY
①
JCBC M6 x 25mm + S/W
M6 + F/W M6 x 13mm
5
②
JCBC M6 x 45mm + S/W
M6 + F/W M6 x 13mm
5
③ Allen Key M4 1
④ L Bracket 5
⑤ CSK Screw M3.5 x 12mm 9
⑥ Wood Dowel M8 x 25mm 3
⑦ Screwdriver
Not
Provided
Hardware
Page 2 of 8
Before
Beginning
Assembly:
Assembly Preparation
Assembly Steps
Overview
This Dining Chair has multiple parts and may require up to some 30 minutes
to assemble. To give you an overview of the Dining Chair parts, the above
picture is to help you put the various parts into perspective. Please read
through the instructions below to familiarise yourself with the parts and
steps before assembly.
Back Stretcher (D)
Front Stretcher (C)
Right Side
Frame (B)
Left Side
Frame (A)
Cushion Seat (F)
Top Rest (E)
Page 3 of 8
Step 1
Step 2
1.1 Place the left side frame (A) and right side frame (B) as shown.
1.2 Align the tenon of front stretcher (C) with the mount position of Side
Frames.
1.3 Align the tenon of back stretcher (D) with mount position of Side
Frames.
Then, fix the Front Scretcher (C) and Back Sctretcher (D) with JCBC Bolt ②
+ Spring Washer + Flat Washer using Allen Key ③.
DO NOT FULLY TIGHTEN SCREWS.
1.1
1.3
1.2
Page 4 of 8
Step 3
Step 4
Place Wood Dowel ⑥ on the Side Frame as shown above.
Place the Top Rest (E) on the back frame as shown above.
Then, fix the Top Rest (E) with JCBC Bolt ① + Spring Washer + Flat
Washer using Allen Key ③.
DO NOT FULLY TIGHTEN SCREWS.
Page 5 of 8
Step 5
Step 6
Place the Cushion Seat (F) on the table, then put the assembled chair
parts in Step4 to fix the Cushion Seat (F) as shown.
Align the Wood Dowel ⑥ into the tenon of Cushion Seat (F) as shown
above.
Then, fix the Cushion Seat (F) with L-Bracket ④ and Screws ⑤ using
Screwdriver (not provided).
DO NOT FULLY TIGHTEN ALL THE BOLT AND SCREWS NOW.
① If wobble
③ Test again
②
30-50mm
Page 6 of 8
Step 7
Place the dining chair on a Level Surface to check if it wobbles. loosen the
bolts. lift the dining chair some 30mm to 50mm high from the ground, keep
your feet and toes well away from the drop zone, and drop the dining chair
freely and vertically with the four legs, hitting the ground at the same time.
This Drop Test will help to ensure that all the bolts and gaps to all reach full
alignment.
Test again for evenness on Level Surface.
If no wobbles are found, proceed to tighten all the Bolts.
Caution: When tightening the Bolts, tighten sequentially.
Do not tighten any screw fully and then towards the next one,this would
cause the frame to warp. If it still wobbles, loosen the bolts and execute this
same drop test.
If the dining chair is not Stable it could lead to damage to the product.
Inspect and make sure all parts are connected.
The dining chair is ready for use.
Caution: This dining chair can only be used on a flat, level surface.
Page 7 of 8
Care & Maintenance
Page 8 of 8
Loading...