Mercury MerCruiser, MerCruiser Axius SeaCore 496 MAG, MerCruiser Axius SeaCore 496 MAG HO, MerCruiser Axius 496 MAG HO Owner's Manual

NOTE: The following applies to CE marked products only.

Declaration of Conformance – Mercury MerCruiser

This sterndrive or inboard engine when installed in accordance to Mercury MerCruisers’ instructions complies with the requirements of the following directives by meeting the associated standards, as amended:

Recreational Craft Directive 94/25/EC; 2003/44/EC

Applicable Requirement Standards Applied

Owner’s manual (A.2.5) ISO 10240

Openings in Hull, Deck and superstructure (A.3.4) ISO 9093‑1; ISO 9093‑2

Handling characteristics (A.4) ISO 8665

Inboard Engine (A.5.1.1) ISO 15584; ISO 10088; ISO 7840; ISO 10133

Fuel System (A.5.2) ISO 10088; ISO 7840; ISO 8469

Electrical System (A.5.3) ISO 10133; ISO 8846

Steering system (A.5.4)

Exhaust emission requirements (B.2) ISO 8178

Owner’s manual (B.4) ISO 8665

Noise emission levels (C.1) ISO 14509

Ignition‑protected equipment (Annex II) ISO 8846; SAE J1171; SAE J1191; SAE J 2031

Applicable portions of: ISO 10592, ISO 8848 and ABYC P‑17

90-899883295 608

*899883295*

Mercury MerCruiser declares that our sterndrive or inboard engines without integral exhaust, when installed in a recreational craft, in accordance with the manufacturers supplied instructions, will meet the exhaust emissions requirements of the directive mentioned above. This engine must not be put into service until the recreational craft in which it is to be installed has been declared in conformity, if so required, with the relevant provision of the directive.

Electromagnetic Compatibility Directive 89/336/EC, 92/31/EEC and 93/68/EEC

Generic emission standard EN 50081‑1

Generic immunity standard EN 50082‑1

Vehicles, boats and internal combustion engine driven devices ‑ Radio disturbance characteristics

Electrostatic discharge testing EN 61000‑6‑2; EN 61000‑4‑2; EN61000‑4‑3

The notified body responsible for surveillance of the quality system under Full Quality Assurance Module H of Directive 2003/44/EC is:

Det Norske Veritas Norway Notified Body Number: 0575

This declaration is issued under the sole responsibility of Mercury Marine and Mercury MerCruiser.

Kevin Grodzki

SAE J551 (CISPR 12)

President ‑ Mercury MerCruiser, Stillwater, OK, USA

Regulatory contact: Regulations and Product Safety Department Mercury Marine W6250 W. Pioneer Road Fond du Lac, WI 54936 USA

Identification Record

Please record the following information:

Engine Model and Horsepower Engine Serial Number

Transom Assembly Serial Number (Sterndrive) Gear Ratio Sterndrive Unit Serial Number

Transmission Model (Inboard) Gear Ratio Transmission Serial Number

Propeller Number Pitch Diameter

Hull Identification Number (HIN) Purchase Date

Boat Manufacturer Boat Model Length

Welcome

The serial numbers are the manufacturer’s keys to numerous engineering details that apply to your Mercury MerCruiser® power package. When contacting your Authorized Mercury MerCruiser Dealer about service, always specify model and serial numbers.

The description and specifications contained herein were in effect at the time this guide was approved for printing. Mercury Marine, whose policy is one of continuous improvement, reserves the right to discontinue models at any time, or to change specifications or designs, without notice and without incurring obligation.

Precision Parts, Mercury Propellers, Mariner, Quicksilver, #1 On The Water, Alpha, Bravo, Bravo Two, Pro Max, OptiMax, Sport‑Jet, K‑Planes, MerCathode, RideGuide, SmartCraft, Zero Effort, M with Waves logo, Mercury with Waves logo, VesselView, and SmartCraft logo are all registered trademarks of Brunswick Corporation. Mercury Product Protection logo is a registered service mark of Brunswick Corporation.

You have selected one of the finest marine power packages available. It incorporates numerous design features to assure operating ease and durability.

With proper care and maintenance, you will thoroughly enjoy using this product for many boating seasons. To ensure maximum performance and carefree use, we ask that you thoroughly read this manual.

The Operation, Maintenance and Warranty Manual contains specific instructions for using and maintaining your product. We suggest that this manual remain with the product for ready reference whenever you are on the water.

Thank you for purchasing one of our Mercury MerCruiser products. We sincerely hope your boating will be pleasant!

Mercury MerCruiser

Warranty Message

The product you have purchased comes with a limited warranty from Mercury Marine; the terms of the warranty are set forth in the Warranty Sections of this manual. The warranty statement contains a description of what is covered, what is not covered, the duration of coverage, how to best obtain warranty coverage, important disclaimers and limitations of damages and other related information. Please review this important information.

Mercury Marine products are designed and manufactured to comply with our own high quality standards, applicable industry standards and regulations, as well as certain emissions regulations. At Mercury Marine every engine is operated and tested before it is boxed for shipment to make sure that the product is ready for use. In addition, certain Mercury Marine products are tested in a controlled and monitored environment, for up to 10 hours of engine run time, in order to verify and make a record of compliance with applicable standards and regulations. All Mercury Marine product, sold as new, receives the applicable limited warranty coverage, whether the engine participated in one of the test programs described above or not.

Read This Manual Thoroughly

IMPORTANT: If you don’t understand any portion of this manual, contact your dealer for a demonstration of actual starting and operating procedures.

Notice

Throughout this publication, and on your power package, dangers, warnings, cautions, and

notices, accompanied by the International Hazard Symbol installer/user to special instructions concerning a particular service or operation that may be hazardous if performed incorrectly or carelessly. These safety alerts follow ANSI standard Z535.6‑2006 for product safety information in product manuals, instructions, and other collateral materials. Observe them carefully.

These Safety Alerts alone cannot eliminate the hazards that they signal. Strict compliance with these special instructions while performing the service, plus common sense operation, are major accident prevention measures.

DANGER

Indicates a hazardous situation which, if not avoided, will result in death or serious injury.

WARNING

Indicates a hazardous situation which, if not avoided, could result in death or serious injury.

CAUTION

Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.

, may be used to alert the

NOTICE

Indicates a situation which, if not avoided, could result in engine or major component failure.

IMPORTANT: Identifies information essential to the successful completion of the task.

NOTE: Indicates information that helps in the understanding of a particular step or action.

WARNING

The operator (driver) is responsible for the correct and safe operation of the boat, the equipment aboard and the safety of all occupants aboard. We strongly recommend that the operator read this Operation, Maintenance and Warranty Manual and thoroughly understand the operational instructions for the power package and all related accessories before the boat is used.

WARNING

The engine exhaust from this product contains chemicals known to the state of California to cause cancer, birth defects or other reproductive harm.

TABLE OF CONTENTS

Section 1 - Warranty

Warranty Registration: United States and

Canada....................................................................2

Warranty Registration: Outside the United States and

Canada....................................................................2

Transfer of Warranty................................................3

Mercury Product Protection Plan: United States and

Canada....................................................................3

Mercury MerCruiser Limited Warranty

(Gasoline‑Fueled Products Only) ...........................4

3‑Year Limited Warranty Against Corrosion............6

Section 2 - Getting to Know Your Power Package

Identification..........................................................14

Engine Serial Number Decal..........................14

Bravo Sterndrive Serial Number and

Identification...................................................14

Bravo Transom Serial Number.......................15

Features and Controls...........................................16

Lanyard Stop Switch......................................16

Emergency Stop (E‑Stop) Switch...................17

Instrumentation...............................................18

VesselView (If Equipped).............................18

SC1000 and SC100 Digital Gauges (If

Equipped).....................................................19

SmartCraft Partner Digital Gauges..............19

Analog Gauges (If Equipped).......................19

Bravo Sterndrive Serial Number and

Identification...................................................20

Electronic Helm Steering................................20

Dual‑Handle Electronic Remote Control (ERC) with DTS Trackpad Features and Operation..21

4‑Year Limited Corrosion Warranty: SeaCore

Sterndrive Models with Gas Engines ......................7

Global Warranty Charts...........................................8

Warranty for Consumer Applications................8

Warranty for Commercial Applications.............9

Warranty for Government Applications............9

Mercury Installation Quality Certification Program 10

Emission Control Information Label.......................11

Owner Responsibility........................................12

Operation.....................................................21

Adjustment...................................................21

Joystick—Basic Operation.............................22

Power Trim.....................................................22

ERC Trim Control.........................................22

Joystick and Trim Control.............................24

Trailer and Trailer Limit Position..................24

Trim without Key.............................................24

Electrical System Overload Protection...........24

Warning Horn Signals....................................27

Audio Warning System...................................27

Caution.........................................................27

Severe..........................................................28

OBDM..........................................................28

Testing The Audio Warning System.............28

Engine Guardian Strategy..............................28

Axius Premier Features (If equipped)....................29

Axius Premier Precision Pilot Trackpad

Functions........................................................29

Safe Boating Suggestions.....................................32

Be Alert to Carbon Monoxide Poisoning................33

Good Ventilation...............................................33

Poor Ventilation ...............................................34

Basic Boat Operation.............................................34

Trailering the Boat..........................................34

Freezing Temperature Operation...................34

Drain Plug and Bilge Pump............................35

Protecting People in the Water..............................35

While You Are Cruising.....................................35

90-899883295 JUNE 2008 Page i

Section 3 - On the Water

While Boat Is Stationary...................................35

High‑Speed and High‑Performance Operation......35

Passenger Safety in Pontoon Boats and Deck

Boats.....................................................................35

Boats Having An Open Front Deck...................36

Boats With Front‑Mounted, Raised Pedestal

Fishing Seats....................................................36

Wave and Wake Jumping......................................36

Impact with Underwater Hazards..........................37

Drive Unit Impact Protection.............................38

Operating with Low Water Inlets in Shallow

Water....................................................................38

Conditions Affecting Operation.............................38

Weight Distribution (Passengers and Gear)

Inside the Boat.............................................. 38

The Bottom of the Boat................................. 38

Cavitation...................................................... 39

Ventilation..................................................... 39

Elevation and Climate................................... 39

Propeller Selection........................................39

Getting Started..................................................... 40

20‑Hour Break‑In Period............................... 40

Launching and Boat Operation..................... 40

Operation Chart.......................................... 40

Starting and Stopping the Engine................. 41

Starting the Engine..................................... 41

Stopping the Engine....................................42

Throttle Only Operation.................................42

Traditional Maneuvering with Steering and

Thrust............................................................43

To Maneuver the Boat in Forward.............. 43

To Steer the Boat in Tight Turns at Low

Speeds........................................................43

To Spin the Boat at Low Speeds................ 43

Maneuvering with the Joystick...................... 43

Special Digital Throttle and Shift (DTS)

Features........................................................48

Dock............................................................49

Throttle Only............................................... 49

1 (Single) Lever...........................................50

Sync............................................................50

After Break‑In Period.....................................51

End of First Season Checkup....................... 51

Axius Premier (If equipped)..................................51

Axius Premier Touchpad Features................51

General Information.................................... 51

Standby.......................................................52

Standby and Active Lights.......................... 52

Power Icon..................................................53

Auto Heading.............................................. 53

Heading Adjustment and Override..............57

Disengage Auto Heading............................57

To Resume to a Heading ...........................57

Changing VesselView Mode Display

Times.......................................................... 58

Skyhook........................................................ 58

Engaging (Activating) Skyhook...................59

The Skyhook Screen in VesselView........... 61

Disengaging (Deactivating) Skyhook..........62

Response Button...........................................63

Track Waypoint............................................. 63

Engaging Track Waypoint Mode.................63

Disengaging Track Waypoint Mode............64

Turn Buttons or Joystick in Track Waypoint

Mode...........................................................65

Auto Heading Button in Track Waypoint

Mode ..........................................................65

Acknowledging a Turn During a Waypoint

Arrival..........................................................65

Waypoint Sequence....................................66

Cruise Control............................................... 69

Contingent Operations......................................... 69

Port Engine Only Operation.......................... 69

Axius Shift Override—Emergency

Procedure......................................................69

Fuel Requirements...............................................72

Fuel Ratings.....................................................72

Using Reformulated (Oxygenated) Gasolines

(USA Only).......................................................72

Gasolines Containing Alcohol..........................72

Engine Oil.............................................................73

Owner/Operator Responsibilities..........................78

Dealer Responsibilities.........................................78

Maintenance.........................................................78

Do‑It‑Yourself Maintenance Suggestions.............79

Inspection.............................................................79

Maintenance Schedules—Axius Models..............80

Page ii 90-899883295 JUNE 2008

Section 4 - Specifications

Engine Specifications...........................................73

Fluid Specifications.............................................. 74

Engine...........................................................74

Sterndrive—Bravo.........................................74

Steering.........................................................74

Power Trim....................................................75

Section 5 - Maintenance

Routine Maintenance—Axius Models........... 80

Scheduled Maintenance—Axius Models.......80

Maintenance Log..................................................81

Engine Oil..............................................................82

Checking...........................................................82

Filling................................................................82

Changing Oil and Filter.....................................83

Easy Engine Oil Drain System.....................83

Engine Oil Drain Pump.................................84

Changing Filter.............................................84

Steering Fluid........................................................85

Checking and Filling Steering Fluid................85

Changing Steering Fluid.................................86

Engine Coolant......................................................86

Checking...........................................................86

Filling................................................................87

Changing .........................................................88

Drive Unit Oil.........................................................88

Checking...........................................................88

Filling................................................................88

Changing..........................................................89

Power Trim Fluid...................................................91

Checking...........................................................91

Filling................................................................91

Changing..........................................................92

Battery...................................................................92

Multiple EFI Engine Battery Precautions........92

Cleaning The Flame Arrestor................................93

Water‑Separating Fuel Filter ................................93

GEN III Models...............................................94

Removal.......................................................94

Installation....................................................95

Lubrication.............................................................96

Electronic Shift Control (ESC) Shift Cable.....96

Sterndrive Unit and Transom Assembly.........96

Sterndrive U‑joint Shaft Splines And O‑rings

(Sterndrive Unit Removed).............................97

Engine Coupler...............................................97

Propellers..............................................................98

Propeller Repair.............................................98

Bravo Three Propeller Removal.....................98

Bravo Three Propeller Installation..................99

Serpentine Drive Belt...........................................101

Checking......................................................101

Replacing.....................................................101

Corrosion Protection............................................103

Corrosion Information...................................103

Maintaining Ground Circuit Continuity..........103

Anodes and MerCathode System Locations 103 Checking the Quicksilver MerCathode

System.........................................................104

Power Package Exterior Surfaces................105

Boat Bottom Care.........................................105

Anti‑fouling Paint..........................................105

Sterndrive Surface Care...............................107

Flushing the Seawater System—Sterndrive

Models.................................................................108

General Information—Bravo Sterndrive.......108

Flushing Attachments.................................108

Sterndrive Water Pickups...........................109

The Boat out of the Water—Bravo

Sterndrive.....................................................109

The Boat in the Water—Bravo Sterndrive....110

The Boat out of the Water—Alternative Water

Pickups.........................................................111

The Boat in the Water—Alternative Water

Pickups.........................................................112

SeaCore Power Package Flushing

Procedure.....................................................113

Models Using The Sterndrive Water

Pickup........................................................113

Cold Weather or Extended Storage.....................120

Preparing Power Package for Storage.........120

Engine and Fuel System Preparation........121

Draining the Seawater System............................122

Drain System Identification...........................122

Air Actuated Single Point Drain System.....122

Manual Drain System.................................123

Air Actuated Single Point Drain System.......123

Check VesselView First.......................................132

Diagnosing EFI Problems....................................132

Diagnosing DTS Problems..................................132

90-899883295 JUNE 2008 Page iii

Section 6 - Storage

Boat in the Water.......................................123

Boat out of the Water.................................125

Manual Drain System...................................127

Boat in the Water.......................................127

Boat out of the Water.................................128

Draining the Sterndrive.................................128

Battery Storage....................................................129

Power Package Recommissioning......................129

Section 7 - Troubleshooting

Engine Guardian System.....................................132

Troubleshooting Charts.......................................132

Starter Motor Will Not Crank Engine, Or Cranks

Slow............................................................132

Engine Will Not Start or Is Hard to Start......133

Poor Performance.......................................133

Engine Runs Rough, Misses, or Backfires..133

Excessive Engine Temperature..................133

Insufficient Engine Temperature.................134

Low Engine Oil Pressure.............................134

Section 8 - Customer Assistance Information

Battery Will Not Recharge...........................134

Joystick.......................................................134

Electronic Remote Controls........................135

Steering System..........................................135

Power Trim Does Not Operate (Motor Does Not

Operate)......................................................136

Power Trim Does Not Operate (Motor Operates

but Sterndrive Unit Does Not Move)...........136

Owner Service Assistance.................................138

Local Repair Service......................................138

Service Away From Home.............................138

Stolen Power Package..................................138

Attention Required after Submersion............138

Replacement Service Parts...........................138

Parts and Accessories Inquiries................139

Resolving a Problem......................................139

Mercury Marine Service Offices.....................139

Ordering Literature.............................................140

United States and Canada............................140

Outside The United States and Canada........140

Dealer Checklist and Customer Orientation.......141

Page iv 90-899883295 JUNE 2008

Section 1 - Warranty

Table of Contents

Warranty Registration: United States and Canada

.............................................................................. 2

Warranty Registration: Outside the United States

and Canada.......................................................... 2

Transfer of Warranty............................................. 3

Mercury Product Protection Plan: United States and

Canada................................................................. 3

Mercury MerCruiser Limited Warranty (Gasoline-

Fueled Products Only) ......................................... 4

3-Year Limited Warranty Against Corrosion......... 6

4-Year Limited Corrosion Warranty: SeaCore

Sterndrive Models with Gas Engines ................... 7

Global Warranty Charts........................................ 8

Warranty for Consumer Applications..............8

Warranty for Commercial Applications............9

Warranty for Government Applications...........9

Mercury Installation Quality Certification Program

............................................................................ 10

Emission Control Information Label.................... 11

Owner Responsibility ................................... 12

90-899883295 JUNE 2008 Page 1

Section 1 - Warranty

Warranty Registration: United States and Canada

To ensure that your warranty coverage begins promptly, your selling dealer should fill out the Warranty Registration Card completely and mail it to the factory immediately upon sale of the new product.

The Warranty Registration Card identifies the name and address of the original purchaser, product model and serial number(s), date of sale, type of use and selling dealer’s code, name, and address. The dealer also certifies that you are the original purchaser and user of the product. A temporary Owner Warranty Registration Card will be presented to you when you purchase the product.

Upon receipt of the Warranty Registration Card at the factory, Mercury MerCruiser will send you an owner resource guide that includes your warranty registration confirmation. If you do not receive your owner resource guide within 60 days from date of new product sale, please contact your selling dealer.

Because of your selling dealer’s ongoing interest in your satisfaction, the product should be returned to him for warranty service.

The product warranty is not effective until the product is registered at the factory.

NOTE: Registration lists must be maintained by the factory and dealer on marine products sold in the United States in the event that a safety recall notification under the Federal Boat Safety Act is required.

You may change your address at any time, including at time of warranty claim, by calling Mercury MerCruiser or sending a letter or fax to Mercury MerCruiser’s warranty registration department with your name, old address, new address, and engine serial number. Your dealer can also process this change of information.

United States customers or dealers may contact: Mercury Marine Attn: Warranty Registration Department W6250 Pioneer Road P.O. Box 1939 Fond du Lac, WI 54936-1939 920-929-5054 Fax 920-929-5893

Canadian customers or dealers may contact: Mercury Marine Canada Limited 2395 Meadowpine Blvd. Mississauga, ON Canada, L5N 7W6 Fax 1-800-663-8334

Warranty Registration: Outside the United States and Canada

To ensure that your warranty coverage begins promptly, your selling dealer should fill out the warranty registration card completely and mail it to the distributor responsible for administering the warranty registration and claim program for your area.

Page 2 90-899883295 JUNE 2008

Section 1 - Warranty

The warranty registration card identifies your name and address, product model and serial numbers, date of sale, type of use, and the selling distributor’s and dealer’s code number, name, and address. The distributor or dealer also certifies that you are the original purchaser and user of the product. A copy of the warranty registration card, designated as the purchaser’s copy, MUST be given to you immediately after the card has been completely filled out by the selling distributor or dealer. This card represents your factory registration identification. Keep the card; if you ever need warranty service on this product, your dealer may ask you for the warranty registration card to verify date of purchase and to use the information on the card to prepare the warranty claim forms.

In some countries, the distributor will issue a permanent (plastic) warranty registration card to you within 30 days after receiving the factory copy of the warranty registration card from your distributor or dealer. If you receive a plastic warranty registration card, you may discard the purchaser’s copy that you received from the distributor or dealer when you purchased the product. Ask your distributor or dealer if this plastic card program applies to you. For further information concerning the warranty registration card and its relationship to warranty claim processing, refer to the International Warranty. See Table of Contents.

NOTE: Registration lists must be maintained by the factory and dealer on marine products sold in the United States in the event of a safety recall notification under the Federal Boat Safety Act.

Transfer of Warranty

The limited warranty is transferable to a subsequent purchaser, but only for the remainder of the unused portion of the limited warranty. This will not apply to products used for commercial applications.

To transfer the warranty to the subsequent owner, send or fax a copy of the bill of sale or purchase agreement, new owner’s name, address and engine serial number to Mercury Marine’s warranty registration department. In the United States mail to:

Mercury Marine Attn: Warranty Registration Department W6250 W. Pioneer Road P.O. Box 1939 Fond du Lac, WI 54936-1939 920-929-5054 Fax 920-929-5893

In Canada mail to: Mercury Marine Canada Limited 2395 Meadowpine Blvd. Mississauga, ON Canada, L5N 7W6 Fax 1-800-663-8334

Upon processing the transfer of warranty, Mercury Marine will send registration verification to the new owner of the product by mail.

There is no charge for this service. For products purchased outside the United States and Canada, contact the distributor in

your country, or the distributor closest to you.

Mercury Product Protection Plan: United States and Canada

(Certain performance products, triple engine installations, and commercial applications are excluded.)

90-899883295 JUNE 2008 Page 3

Section 1 - Warranty

The Mercury Product Protection Plan provides coverage against unexpected mechanical and electrical breakdowns that may occur beyond the standard limited warranty.

The optional Mercury Product Protection Plan is the only Factory Plan available for your engine.

One‑, two‑, three‑, four‑, or five‑ year term plans can be purchased up to 12 months after the original engine registration date.

See your participating Mercury MerCruiser dealer for complete program details.

Mercury MerCruiser Limited Warranty (Gasoline‑Fueled Products Only)

Mercury MerCruiser Limited Warranty (Gasoline-Fueled Products Only)

What is Covered

Mercury Marine warrants its new products to be free of defects in material and workmanship during the period described following.

Duration of Coverage

Warranty Period for Recreational Use

The warranty period begins on the date the product is first sold to a recreational‑use retail purchaser or the date on which the product is first put into service, whichever occurs first. Products installed by an Installation Quality Certified Installer receive one (1) year of additional warranty coverage. The repair or replacement of parts or the performance of service under this warranty does not extend the life of this warranty beyond its original expiration date. The warranty period is specific to the model covered; see your model for the base coverage period:

Coverage for Horizon Inboard Models, and Vazer 100 Sterndrive Models

The Limited Warranty for Horizon Inboard Models and Vazer 100 Models is four (4) years when installed by an Installation Quality Certified Installer or three (3) years for non‑certified installations..

Coverage for SeaCore Sterndrive Models

The Limited Warranty for SeaCore Sterndrive Models is four (4) years when installed by an Installation Quality Certified Installer or three (3) years for non‑certified installations.

Coverage for Tow Sports Inboard Models

The Limited Warranty for all Tow Sports Inboard models is three (3) years when installed by an Installation Quality Certified Installer or two (2) years for non‑certified installations.

Coverage for All Other Models

The Limited Warranty for all other Gasoline Sterndrive and Inboard models except those described above is two (2) years when installed by an Installation Quality Certified Installer or one (1) year for non‑certified installations.

Warranty Period for Commercial Use

The warranty period begins on the date the product is first sold to a commercial‑use retail purchaser or the date on which the product is first put into service, whichever occurs first. Commercial users of these products receive warranty coverage for either one (1) year from the date of first retail sale or the accumulation of 500 hours of operation, whichever occurs first. Commercial use is defined as any work‑related or employment‑related use of the product, or any use of the product that generates income for any part of the warranty period, even if the product is only occasionally used for such purposes. The repair or replacement of parts or the performance of service under this warranty does not extend the life of this warranty beyond its original expiration date.

Transfer of Coverage

Unexpired warranty coverage can be transferred from one recreational‑use customer to a subsequent recreational‑use customer upon proper reregistration of the product. Unexpired warranty coverage cannot be transferred either to or from a commercial‑use customer.

Termination of Coverage

Warranty coverage is terminated for used product obtained in any of the following ways:

• Repossession from a retail customer

• Purchase at auction

• Purchase from a salvage yard

• Purchase from an insurance company that obtained the product as a result of an insurance claim

Page 4 90-899883295 JUNE 2008

Section 1 - Warranty

Conditions That Must Be Met in Order to Obtain Warranty Coverage

Warranty coverage is available only to retail customers that purchase from a dealer authorized by Mercury Marine to distribute the product in the country in which the sale occurred, and then only after the pre‑delivery inspection process specified by Mercury Marine is completed and documented. Warranty coverage becomes available upon proper registration of the product by the authorized dealer. Inaccurate warranty registration information regarding recreational use or subsequent change of use from recreational to commercial (unless properly reregistered) may void the warranty at the sole discretion of Mercury Marine. Routine maintenance must be performed according to the maintenance schedule in the Operation, Maintenance & Warranty manual in order to obtain warranty coverage. Mercury Marine reserves the right to make any warranty coverage contingent upon proof of proper maintenance.

What Mercury Marine Will Do

Mercury Marine's sole and exclusive obligation under this warranty is limited to, at our option, repairing a defective part, replacing such part or parts with new or Mercury Marine certified remanufactured parts, or refunding the purchase price of the Mercury Marine product. Mercury Marine reserves the right to improve or modify products from time to time without assuming an obligation to modify products previously manufactured.

How to Obtain Warranty Coverage

The customer must provide Mercury Marine with a reasonable opportunity to repair and reasonable access to the product for warranty service. Warranty claims shall be made by delivering the product for inspection to a Mercury Marine dealer authorized to service the product. If the purchaser cannot deliver the product to such a dealer, written notice must be given to Mercury Marine. Mercury Marine will then arrange for the inspection and any covered repair. The purchaser in that case shall pay for all related transportation charges and travel time. If the service provided is not covered by this warranty, the purchaser shall pay for all related labor and material and any other expenses associated with that service. The purchaser shall not, unless requested by Mercury Marine, ship the product or parts of the product directly to Mercury Marine. Proof of registered ownership must be presented to the dealer at the time warranty service is requested in order to obtain coverage.

What Is Not Covered

This limited warranty does not cover the following:

• Routine maintenance items

• Adjustments

• Normal wear and tear

• Damage caused by abuse

• Abnormal use

• Use of a propeller or gear ratio that does not allow the engine to run in its recommended RPM range (see the Operation, Maintenance & Warranty manual)

• Operation of the product in a manner inconsistent with the recommended operation and duty cycle section of the Operation, Maintenance & Warranty manual

• Neglect

• Accident

• Submersion

• Improper installation (proper installation specifications and techniques are set forth in the installation instructions for the product)

• Improper service

• Use of an accessory or part that was not manufactured or sold by Mercury Marine and that damages the Mercury product

• Jet pump impellers and liners

• Operation with fuels, oils, or lubricants that are not suitable for use with the product (see the Operation, Maintenance & Warranty manual)

• Alteration or removal of parts

• Water entering the engine through the fuel intake, air intake, or exhaust system or damage to the product from insufficient cooling water caused by blockage of the cooling system by a foreign body

• Running the engine out of water

• Mounting the engine too high on the transom

• Operating the boat with the engine over trimmed

90-899883295 JUNE 2008 Page 5

Section 1 - Warranty

Use of the product for racing or other competitive activity, or operating with a racing‑type lower unit at any point, even by a previous owner of the product, voids the warranty. Expenses related to haul‑out, launch, towing, storage, telephone, rental, inconvenience, slip fees, insurance coverage, loan payments, loss of time, loss of income, or any other type of incidental or consequential damages are not covered by this warranty. Also, expenses associated with the removal or replacement of boat partitions or other material in order to gain access to the product are not covered by this warranty. No individual or entity, including Mercury Marine authorized dealers, has been given authority by Mercury Marine to make any affirmation, representation, or warranty regarding the product, other than those contained in this limited warranty. If such affirmation, representation, or warranty is made, it shall not be enforceable against Mercury Marine.

DISCLAIMERS AND LIMITATIONS THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE EXPRESSLY DISCLAIMED. TO THE EXTENT THAT THEY CANNOT BE DISCLAIMED, THE IMPLIED WARRANTIES ARE LIMITED IN DURATION TO THE LIFE OF THE EXPRESS WARRANTY. INCIDENTAL AND CONSEQUENTIAL DAMAGES ARE EXCLUDED FROM COVERAGE UNDER THIS WARRANTY. SOME STATES/COUNTRIES DO NOT ALLOW FOR THE DISCLAIMERS, LIMITATIONS AND EXCLUSIONS IDENTIFIED ABOVE. AS A RESULT, THEY MAY NOT APPLY TO YOU. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER LEGAL RIGHTS WHICH VARY FROM STATE TO STATE AND COUNTRY TO COUNTRY.

3‑Year Limited Warranty Against Corrosion

3-YEAR LIMITED WARRANTY AGAINST CORROSION

What Is Covered

Mercury Marine warrants that each new Mercury, Mariner, Mercury Racing, Sport Jet, M2 Jet Drive, Tracker by Mercury Marine Outboard, MerCruiser Inboard or Sterndrive engine (Product) will not be rendered inoperative as a direct result of corrosion for the period of time described below.

Duration of Coverage

This limited corrosion warranty provides coverage for three (3) years from either the date the product is first sold, or the date on which the product is first put into service, whichever occurs first. The repair and replacement of parts, or the performance of service under this warranty does not extend the life of this warranty beyond its original expiration date. Unexpired warranty coverage can be transferred to subsequent (noncommercial use) purchaser upon proper re‑registration of the product. Warranty coverage is terminated for used product repossessed from a retail customer, purchased at auction, from a salvage yard, or from an insurance company that obtained the product as a result of an insurance claim.

Condition That Must Be Met in Order to Obtain Warranty Coverage

Warranty coverage is available only to retail customers that purchase from a dealer authorized by Mercury Marine to distribute the product in the country in which the sale occurred, and then only after the Mercury Marine specified pre‑delivery inspection process is completed and documented. Warranty coverage becomes available upon proper registration of the product by the authorized dealer. Corrosion prevention devices specified in the Operation, Maintenance & Warranty manual must be in use on the boat, and routine maintenance outlined in the Operation, Maintenance & Warranty manual must be timely performed (including without limitation the replacement of sacrificial anodes, use of specified lubricants, and touch‑up of nicks and scratches) in order to maintain warranty coverage. Mercury Marine reserves the right to make warranty coverage contingent upon proof of proper maintenance.

What Mercury Will Do

Mercury's sole and exclusive obligation under this warranty is limited to, at our option, repairing a corroded part, replacing such part or parts with new or Mercury Marine certified re‑manufactured parts, or refunding the purchase price of the Mercury product. Mercury reserves the right to improve or modify products from time to time without assuming an obligation to modify products previously manufactured.

How to Obtain Warranty Coverage

The customer must provide Mercury with a reasonable opportunity to repair, and reasonable access to the product for warranty service. Warranty claims shall be made by delivering the product for inspection to a Mercury dealer authorized to service the product. If purchaser cannot deliver the product to such a dealer, written notice must be given to Mercury. We will then arrange for the inspection and any covered repair. Purchaser in that case shall pay for all related transportation charges and/or travel time. If the service provided is not covered by this warranty, purchaser shall pay for all related labor and material, and any other expenses associated with that service. Purchaser shall not, unless requested by Mercury, ship the product or parts of the product directly to Mercury. Proof of registered ownership must be presented to the dealer at the time warranty service is requested in order to obtain coverage.

What Is Not Covered

Page 6 90-899883295 JUNE 2008

Section 1 - Warranty

This limited warranty does not cover electrical system corrosion; corrosion resulting from damage, corrosion which causes purely cosmetic damage, abuse or improper service; corrosion to accessories, instruments, steering systems; corrosion to factory installed jet drive unit; damage due to marine growth; product sold with less than a one year limited Product warranty; replacement parts (parts purchased by the Customer); products used in a commercial application. Commercial use is defined as any work or employment related use of the product, or any use of the product which generates income, for any part of warranty period, even if the product is only occasionally used for such purposes.

4‑Year Limited Corrosion Warranty: SeaCore Sterndrive Models with Gas Engines

4-YEAR LIMITED CORROSION WARRANTY: SEACORE STERNDRIVE MODELS WITH GAS ENGINES

What Is Covered

Mercury Marine warrants that each new MerCruiser SeaCore engine, transom, and sterndrive package will not be rendered inoperative as a direct result of corrosion for the period of time described below.

Duration of Coverage

This limited corrosion warranty provides coverage for four (4) years from either the date on which the MerCruiser SeaCore engine, transom, and sterndrive package is first sold or the date on which it is first put into service, whichever occurs first. The repair or replacement of parts or the performance of service under this warranty does not extend the life of this warranty beyond its original expiration date. Unexpired warranty coverage can be transferred to a subsequent (noncommercial‑use) purchaser upon proper reregistration of the product. Warranty coverage is terminated for used product obtained in any of the following ways:

• Repossession from a retail customer

• Purchase at auction

• Purchase from a salvage yard

• Purchase from an insurance company that obtained the product as a result of an insurance claim

Condition That Must Be Met in Order to Obtain Warranty Coverage

Warranty coverage is available only to retail customers that purchase from a dealer authorized by Mercury Marine to distribute the product in the country in which the sale occurred, and then only after the pre‑delivery inspection process specified by Mercury Marine is completed and documented. Warranty coverage becomes available upon proper registration of the product by the authorized dealer. Corrosion‑prevention devices specified in the Operation, Maintenance & Warranty manual must be in use on the boat, and routine maintenance outlined in the Operation, Maintenance & Warranty manual must be performed according to the maintenance schedule in the Operation, Maintenance & Warranty manual (including without limitation the replacement of sacrificial anodes, use of specified lubricants, and touch‑up of nicks and scratches) in order to maintain warranty coverage. Mercury Marine reserves the right to make warranty coverage contingent upon proof of proper maintenance.

What Mercury Marine Will Do

Mercury's sole and exclusive obligation under this warranty is limited to, at our option, repairing a corroded part, replacing such part or parts with new or Mercury Marine certified remanufactured parts, or refunding the purchase price of the Mercury product. Mercury reserves the right to improve or modify products from time to time without assuming an obligation to modify products previously manufactured.

How to Obtain Warranty Coverage

The customer must provide Mercury Marine with a reasonable opportunity to repair and reasonable access to the product for warranty service. Warranty claims shall be made by delivering the product for inspection to a Mercury Marine dealer authorized to service the product. If the purchaser cannot deliver the product to such a dealer, written notice must be given to Mercury Marine. Mercury Marine will then arrange for the inspection and any covered repair. The purchaser in that case shall pay for all related transportation charges and/or travel time. If the service provided is not covered by this warranty, the purchaser shall pay for all related labor and material, and any other expenses associated with that service. The purchaser shall not, unless requested by Mercury Marine, ship the product or parts of the product directly to Mercury Marine. Proof of registered ownership must be presented to the dealer at the time warranty service is requested in order to obtain coverage.

What Is Not Covered

90-899883295 JUNE 2008 Page 7

Section 1 - Warranty

This limited warranty does not cover the following:

• Electrical system corrosion

• Corrosion resulting from damage

• Corrosion that causes purely cosmetic damage

• Abuse or improper service

• Corrosion to accessories, instruments, and steering systems

• Corrosion to a factory‑installed jet drive unit

• Damage due to marine growth

• Replacement parts (parts purchased by the customer)

• Product sold with less than a one‑year limited product warranty

• Products used in a commercial application. Commercial use is defined as any work or employment related use of the product, or any use of the product which generates income, for any part of warranty period, even if the product is only occasionally used for such purposes.

Global Warranty Charts

Warranty for Consumer Applications

Engine Model

Axius SeaCore 496 MAG Axius SeaCore 496 MAG HO

Axius 496 MAG Axius 496 MAG HO

The Americas (excluding Brazil)

Brazil

Europe, Middle East, Africa

Australia, New Zealand

Japan

South Pacific

Other Asia

The Americas (excluding Brazil)

Brazil

Europe, Middle East, Africa

Australia, New Zealand

Japan

South Pacific

Other Asia

Region

Standard Factory Limited Warranty by

Certification Status of Boat Manufacturer

Not Certified

3 years 4 years 3 years

2 years 2 years 2 years

3 years

1 year 1 year 1 year

2 years 2 years 2 years

1 year 1 year 1 year

1 year

2 years

1 year 1 year 1 year

2 years 2 years 2 years

1 year 1 year 1 year

Installation Quality

Certified

4 years

3 years

2 years 2 years

3 years

Consumer Limited

Corrosion Warranty

4 years

3 years

2 years

Page 8 90-899883295 JUNE 2008

Warranty for Commercial Applications

Engine Model Region

The Americas (excluding Brazil)

Brazil

Axius SeaCore 496 MAG Axius SeaCore 496 MAG HO

Axius 496 MAG Axius 496 MAG HO

Europe, Middle East, Africa

Australia, New Zealand

Japan

South Pacific

Other Asia

The Americas (excluding Brazil)

Brazil

Europe, Middle East, Africa

Australia, New Zealand

Japan

South Pacific

Other Asia

Section 1 - Warranty

Standard Factory Limited Warranty by

Certification Status of Boat Manufacturer

Not Certified

1 year 1 year 1 year

2 years 2 years 2 years

1 year or 500 hours 1 year or 500 hours 1 year or 500 hours

1 year 1 year 1 year

2 years 2 years 2 years

1 year or 500 hours 1 year or 500 hours 1 year or 500 hours

Installation Quality

Certified

Commercial Limited

Corrosion Warranty

Warranty for Government Applications

Engine Model

Axius SeaCore 496 MAG Axius SeaCore 496 MAG HO

Axius 496 MAG Axius 496 MAG HO

The Americas (excluding Brazil)

Brazil

Europe, Middle East, Africa

Australia, New Zealand

Japan

South Pacific

Other Asia

The Americas (excluding Brazil)

Brazil

Europe, Middle East, Africa

Australia, New Zealand

Japan

South Pacific

Other Asia

Region

Standard Factory Limited Warranty by

Certification Status of Boat Manufacturer

Not Certified

1 year 1 year 1 year

2 years 2 years 2 years

1 year or 500 hours 1 year or 500 hours 1 year or 500 hours

1 year 1 year 1 year

2 years 2 years 2 years

1 year or 500 hours 1 year or 500 hours 1 year or 500 hours

Installation Quality

Certified

Government Limited

Corrosion Warranty

90-899883295 JUNE 2008 Page 9

Section 1 - Warranty

Mercury Installation Quality Certification Program

15502

Mercury MerCruiser products installed by a Mercury Installation Quality Certified Manufacturer are Installation Quality certified products and may receive an additional one (1) year of limited warranty coverage.

The Installation Quality Certification program was developed to recognize MerCruiser boatbuilder customers who have achieved higher manufacturing standards. It is the first and only comprehensive manufacturer‑installation certification program in the industry.

The program has three goals:

1. To enhance overall product quality.

2. To improve the boat ownership experience.

3. To enhance overall customer satisfaction. The certification process is designed to review all facets of manufacturing and engine

installation. The program is composed of design, manufacturing and installation review stages with which builders must comply. Certification applies leading‑edge methodologies to create:

• Efficiencies and best practices specific to engine installation.

• World‑class assembly and component specifications.

• Efficient installation processes.

• Industry standard end‑of‑line test procedures Boat builders that successfully complete the program and meet all certification

requirements earn Installation Quality System Certified Manufacturer status and receive an additional one (1) year of Mercury limited factory warranty coverage on all MerCruiser‑powered boats that are registered on and after the boat builder's certification date for all worldwide registrations.

Mercury has designated a section of our Website to promote the Installation Quality Certification Program and communicate its benefits to consumers. For a current list of MerCruiser‑powered boat brands that have earned Installation Quality Certification, visit

www.mercurymarine.com/mercruiser_warranty.

Page 10 90-899883295 JUNE 2008

Emission Control Information Label

EMISSION CONTROL

INFORMATION

THIS ENGINE CONFORMS TO XXXX CALIFORNIA EMISSION REGULATIONS FOR SPARK IGNITION MARINE ENGINES REFER TO OWNER'S MANUAL FOR MAINTENANCE SPECIFICATIONS AND ADJUSTMENTS

SERIAL #

FAMILY

STD.

D.O.M.

DISP

31656

XXXXXXXXXXXX XX.X g/kW-hr

XXXXXXXX

X.XL

MMM YYYY

0575

EMISSION CONTROL

INFORMATION

REFER TO OWNER'S MANUAL FOR MAINTENANCE SPECIFICATIONS AND ADJUSTMENTS

SERIAL #

FAMILY

STD.

D.O.M.

DISP

31657

XXXXXXXXXXXX XX.X g/kW-hr

XXXXXXXX

X.XL

MMM YYYY

NOT FOR SALE IN CALIFORNIA

A tamper‑resistant Emission Control Information label is affixed in a visible location to the engine at time of manufacture by Mercury MerCruiser. In addition to the required emissions statement, the label lists the engine serial number, family, STD (emission standard/level), date of manufacture (month, year), and the engine displacement. Please note that the low emissions certification will not affect the fit, function, or performance of the engines. Boatbuilders and dealers may not remove the label or the part it is affixed to before sale. If modifications are necessary, contact Mercury MerCruiser about the availability of replacement decals before proceeding.

NOTE: When the CE mark is present in the lower right corner of the Emission Control Information Label on the engine, the Declaration of Conformance applies. Refer to the front page of this manual for further information.

Section 1 - Warranty

Emission Control Label—California Emissions–Compliant

"SERIAL#"—Engine Serial Number "FAMILY"—Engine Family "STD."—Emissions Standard "D.O.M."—Date of Manufacture "DISP"—Piston Displacement

Emission Control Label—Not for Sale in California

"SERIAL#"—Engine Serial Number "FAMILY"—Engine Family "STD."—Emissions Standard "D.O.M."—Date of Manufacture

90-899883295 JUNE 2008 Page 11

"DISP"—Piston Displacement

Section 1 - Warranty

Owner Responsibility

The operator must have routine engine maintenance performed to maintain emission levels within prescribed certification standards.

The operator may not modify the engine in any manner that alters the horsepower or allows emissions levels to exceed their factory specifications.

Page 12 90-899883295 JUNE 2008

Section 2 - Getting to Know Your Power Package

Table of Contents

Section 2 - Getting to Know Your Power Package

Identification........................................................ 14

Engine Serial Number Decal.........................14

Bravo Sterndrive Serial Number and

Identification..................................................14

Bravo Transom Serial Number......................15

Features and Controls........................................ 16

Lanyard Stop Switch.....................................16

Emergency Stop (E-Stop) Switch..................17

Instrumentation.............................................18

VesselView (If Equipped) ....................... 18

SC1000 and SC100 Digital Gauges (If

Equipped) ............................................... 19

SmartCraft Partner Digital Gauges ........ 19

Analog Gauges (If Equipped) ................. 19

Bravo Sterndrive Serial Number and

Identification..................................................20

Electronic Helm Steering...............................20

Dual-Handle Electronic Remote Control (ERC) with DTS Trackpad Features and Operation

......................................................................21

Operation ............................................... 21

Adjustment ............................................. 21

Joystick—Basic Operation............................22

Power Trim....................................................22

ERC Trim Control ................................... 22

Joystick and Trim Control ....................... 24

Trailer and Trailer Limit Position ............ 24

Trim without Key...........................................24

Electrical System Overload Protection..........24

Warning Horn Signals...................................27

Audio Warning System..................................27

Caution ................................................... 27

Severe .................................................... 28

OBDM .................................................... 28

Testing The Audio Warning System ....... 28

Engine Guardian Strategy.............................28

Axius Premier Features (If equipped)................. 29

Axius Premier Precision Pilot Trackpad

Functions.......................................................29

90-899883295 JUNE 2008 Page 13

Section 2 - Getting to Know Your Power Package

25902

33533

Identification

The serial numbers are the manufacture's keys to numerous engineering details which apply to your MerCruiser power package. When contacting MerCruiser about service, always specify model and serial numbers.

Engine Serial Number Decal

The serial number decal is located on top of the engine.

Serial numbers and maintenance color codes decal

The engine serial number is also stamped in the engine block.

Bravo Sterndrive Serial Number and Identification

The Bravo sterndrive serial number, gear ratio, model number, and bar code are embedded in the ground plate on the port side of the sterndrive.

Bravo sterndrive information on ground plate

Page 14 90-899883295 JUNE 2008

The serial number is also stamped as a permanent reference on the sterndrive casting

33534

25904

inside the back cover.

Bravo sterndrive serial number stamping

Bravo Transom Serial Number

The Bravo transom serial number is stamped in the U‑bolt plate of the Bravo transom assembly.

Section 2 - Getting to Know Your Power Package

a - Transom assembly serial Number

90-899883295 JUNE 2008 Page 15

Bravo transom assembly U‑bolt plate

Section 2 - Getting to Know Your Power Package

25905

The serial number is also stamped on the gimbal housing. This is used as a permanent reference for authorized MerCruiser Dealers.

Gimbal housing with serial number stamping

a - Transom assembly serial Number

Features and Controls

Lanyard Stop Switch

The purpose of a lanyard stop switch is to turn off the engine when the operator moves outside the operator's position (as in accidental ejection from the operator's position).

Accidental ejections, such as falling overboard, are more likely to occur in:

• low‑sided sport boats

• bass boats

• high performance boats Accidental ejections can also occur from:

• poor operating practices

• sitting on the seat or gunwale at planing speeds

• standing at planing speeds

• operating at planing speeds in shallow or obstacle infested waters

• releasing your grip on the steering wheel that is pulling in one direction

• consuming alcohol or drugs

• high speed boating maneuvers

a - Stop switch b - Lanyard

RUN

74608

c - Clips to the operator

Page 16 90-899883295 JUNE 2008

Section 2 - Getting to Know Your Power Package

The lanyard is a cord usually between 122 and 152 cm (4 and 5 ft) in length when stretched out, with an element on one end made to be inserted into the switch and a snap on the other end for attaching to the operator. The lanyard is coiled to make its at‑rest condition as short as possible to minimize the likelihood of lanyard entanglement with nearby objects. Its stretched‑out length is made to minimize the likelihood of accidental activation should the operator choose to move around in an area close to the normal operator's position. If it is desired to have a shorter lanyard, wrap the lanyard around the operator's wrist or leg, or tie a knot in the lanyard.

Activation of the lanyard stop switch will stop the engine immediately, but the boat will continue to coast for some distance depending upon the velocity and degree of any turn at shut down. However, the boat will not complete a full circle. While the boat is coasting, it can cause injury to anyone in the boat's path as seriously as the boat would when under power.

We strongly recommend that other occupants be instructed on proper starting and operating procedures should they be required to operate the engine in an emergency (e.g. if the operator is accidentally ejected).

WARNING

If the operator falls out of the boat, stop the engine immediately to reduce the possibility of serious injury or death from being struck by the boat. Always properly connect the operator to the stop switch using a lanyard.

Accidental or unintended activation of the switch during normal operation is also a possibility. This could cause any, or all, of the following potentially hazardous situations:

• Occupants could be thrown forward due to unexpected loss of forward motion, a particular concern for passengers in the front of the boat who could be ejected over the bow and possibly struck by the propulsion or steering components.

• Loss of power and directional control in heavy seas, strong current or high winds.

• Loss of control when docking.

Avoid serious injury or death from deceleration forces resulting from accidental or unintended stop switch activation. The boat operator should never leave the operator's station without first disconnecting the stop switch lanyard from the operator.

Emergency Stop (E‑Stop) Switch

The emergency stop (E‑stop) switch turns off the engines in an emergency situation, such as a person overboard or tangled propeller. When activated, the E‑stop switch interrupts the power supply to the main power relay, including power to the gauges, steering, and accessories.

Activation of the E‑stop switch stops the engines immediately, but the boat continues to coast for some distance depending upon the velocity and degree of any turn at shutdown. However, the boat does not complete a full circle. While the boat is coasting, it can cause injury to anyone in the boat's path as seriously as the boat would when under power.

We recommend instructing other occupants on proper starting and operating procedures should they need to operate the engine in an emergency.

Accidental or unintended activation of the switch during normal operation is also possible, which can cause any or all of the following potentially hazardous situations:

WARNING

90-899883295 JUNE 2008 Page 17

Section 2 - Getting to Know Your Power Package

27198

• Occupants can be thrown forward due to unexpected loss of forward motion, a particular concern for passengers in the front of the boat who could be ejected over the bow and possibly struck by the propulsion or steering components.

• Operator can lose power and directional control in heavy seas, strong current, or high winds.

• Operator can lose control when docking.

Instrumentation

VESSELVIEW (IF EQUIPPED)

The SmartCraft VesselView is the recommended information source for all drive information, engine information, fault codes, vessel information, basic navigation data, and system information.

Refer to the VesselView Operator's Manual for more information.

VesselView

Page 18 90-899883295 JUNE 2008

SC1000 AND SC100 DIGITAL GAUGES (IF EQUIPPED)

24575

OIL

C H

TEMP

R P M

X 1000

MPH

KPH

100

120

110

10 16

BATT

FUEL

CRUISELOG

0 0 0 0

32757

The SmartCraft SC1000 and SC100 digital gauges complement VesselView. Refer to the SC1000 and SC100 Digital Gauge Operator's Manual for more information.

Typical SmartCraft gauges

a - Tachometer b - Speedometer c - LCD System View display

Section 2 - Getting to Know Your Power Package

SMARTCRAFT PARTNER DIGITAL GAUGES

For other gauge manufacturers and other SmartCraft compatible products, visit www.smartcraftnetworked.com. See the specific manufacturer's operation manual for more information.

ANALOG GAUGES (IF EQUIPPED)

Instrumentation packages may vary, and may contain additional gauges. The owner and operator should be familiar with all the instruments and their functions on the boat. Ask your boat dealer to explain the gauges and normal readings that appear on your boat.

Your package may include the following types of gauges may be included with your power package.

90-899883295 JUNE 2008 Page 19

Section 2 - Getting to Know Your Power Package

33533

33534

Item Gauge Function

a Speedometer Indicates boat speed.

b Tachometer Indicates engine RPM.

c Oil pressure gauge Indicates engine oil pressure.

d Voltmeter Indicates battery voltage.

e Water temperature gauge Indicates engine operating temperature.

f Fuel gauge Indicates the quantity of fuel in tank.

g Hour meter Records engine operating time.

Bravo Sterndrive Serial Number and Identification

The Bravo sterndrive serial number, gear ratio, model number, and bar code are embedded in the ground plate on the port side of the sterndrive.

The serial number is also stamped as a permanent reference on the sterndrive casting inside the back cover.

Electronic Helm Steering

The electronic helm steering operates through electronic signals. A computer‑controlled electric motor simulates the resistance feedback found in hydraulic steering systems.

Bravo sterndrive information on ground plate

Bravo sterndrive serial number stamping

Page 20 90-899883295 JUNE 2008

Section 2 - Getting to Know Your Power Package

We recommend that you drive carefully until you have a chance to explore the Axius system's handling characteristics and boat's responses in an open area clear of obstructions or other boat traffic. The initial steering setting of two turns lock‑to‑lock provids a fast steering response. Maneuvers at speed can be more abrupt than expected. The distributor can adjust the number of turns, if desired.

Dual‑Handle Electronic Remote Control (ERC) with DTS Trackpad Features and Operation

OPERATION

The electronic remote control (ERC) handle operates the shift and throttle. Push the ERC handles handle forward from neutral to the first detent for forward gear. Continue pushing the ERC handle forward to increase speed. Pull the ERC handle from the forward position to the neutral position to decrease speed and eventually stop. Pull the ERC handle back from neutral to the first detent for reverse gear. Continue pulling the handle back to increase speed.

NOTE: When using the joystick, the computer moves the sterndrive in and out of gear even though the ERC handles remain in neutral.

ADJUSTMENT

28086

Typical ERC handles

a - Neutral b - Forward c - Reverse d - Bow of boat

The amount of force needed to move the ERC handles and to move the ERC handles through the detentes is adjustable to help prevent unwanted motion of the handle in rough water.

To adjust ERC handle tension:

1. Remove the port side cover for port lever adjustment, and starboard side cover for

starboard lever adjustment.

2. Turn the screw clockwise to increase tension on the control handle and

counter‑clockwise to decrease tension.

3. Adjust to tension desired. To adjust ERC handle detent tension:

1. Remove the port side cover for port lever adjustment, and starboard side cover for

starboard lever adjustment.

90-899883295 JUNE 2008 Page 21

Section 2 - Getting to Know Your Power Package

2. Turn the screw clockwise to increase tension on the control handle and counter‑clockwise to decrease tension.

3. Adjust to desired tension.

Starboard side with side cover removed.

a - ERC handle tension adjustment screw, labeled "De" b - ERC handle detent tension adjustment screw, labeled "Fr"

28087

Joystick—Basic Operation

The joystick offers precise, intuitive control of your boat during low speed and docking maneuvers. Engine speed is limited in this mode to prevent excessive prop wash or unacceptable boat dynamics during maneuvers.

Though joystick operation is easy and intuititve, you should avoid using it until you have the opportunity to become familiar with the joystick in open water. Thereafter, you should occaisionallly practice operating without the joystick in case the joystick becomes inoperable.

Power Trim

Power trim allows the operator to adjust the sterndrive angle while underway to achieve the ideal boat angle for varying load and water conditions. The trailering feature allows the operator to raise and lower the sterndrive unit for trailering, beaching, launching, low speed (below 1200 rpm), and shallow water operation.

ERC TRIM CONTROL

Excessive trim can cause serious injury or death at high speeds. Use caution when trimming the sterndrive, and never trim out beyond the gimbal ring support flanges while the boat is underway or at engine speeds above 1200 RPM.

Some ERC's will have a single button for trimming both sterndrives simultaneously or may have separate buttons for each sterndrive unit.

WARNING

Page 22 90-899883295 JUNE 2008

+ 120 hidden pages

Mercury MerCruiser, MerCruiser Axius SeaCore 496 MAG, MerCruiser Axius SeaCore 496 MAG HO, MerCruiser Axius 496 MAG HO Owner's Manual

Specifications and Main Features

Frequently Asked Questions

User Manual