Mercury 2003-Mercury-Marauder, 2003 Marauder Owner's Manual

www.carburetor-manual.com

Would you like some Free Manuals?

http://carburetor-manual.com/free-shop-manual-club-t-13.html

Also visit http://freeshopmanual.com for more Free Manuals

Also Visit my website for 7 FREE Download Manuals starting

with this one.

"The ABC's of Carburetion"

Click Here Now

file:///C|/Documents%20and%20Settings/Tim/Desktop/carburetor-manual-welcome/index.htm[4/25/2009 11:42:20 AM]

Table of Contents

Introduction 4
Instrument Cluster 10

Warning and control lights 10
Gauges 15

Entertainment Systems 19

AM/FM stereo cassette with CD 19
CD changer 28

Climate Controls 33

Electronic automatic temperature control 33

Lights 38

Headlamps 38
Turn signal control 42
Bulb replacement 43

Driver Controls 49

Windshield wiper/washer control 49
Steering wheel adjustment 50
Power windows 60
Mirrors 61
Speed control 63

Locks and Security 75

Keys 75
Locks 75
Anti-theft system 77

Seating and Safety Restraints 88

Seating 88
Safety restraints 91
Air bags 104
Child restraints 111

1

Table of Contents

Driving 122

Starting 122
Brakes 126
Traction control/AdvanceTrac 128
Air suspension 130
Transmission operation 131
Vehicle loading 136
Trailer towing 138

Roadside Emergencies 142

Getting roadside assistance 142
Hazard flasher switch 143
Fuel pump shut-off switch 143
Fuses and relays 144
Changing tires 151
Jump starting 156
Wrecker towing 162

Customer Assistance 163

Reporting safety defects (U.S. only) 172

Cleaning 173
Maintenance and Specifications 179

Engine compartment 181
Engine oil 182
Battery 186
Fuel information 194
Air filter(s) 206
Part numbers 211
Refill capacities 211
Lubricant specifications 212

2

Table of Contents

Accessories 218
Index 221

All rights reserved. Reproduction by any means, electronic or mechanical
including photocopying, recording or by any information storage and retrieval
system or translation in whole or part is not permitted without written
authorization from Ford Motor Company. Ford may change the contents without
notice and without incurring obligation.

Copyright © 2002 Ford Motor Company

3

Introduction

CALIFORNIA Proposition 65 Warning

WARNING: Engine exhaust, some of its constituents, and

certain vehicle components contain or emit chemicals known to
the State of California to cause cancer and birth defects or other
reproductive harm. In addition, certain fluids contained in vehicles and
certain products of component wear contain or emit chemicals known
to the State of California to cause cancer and birth defects or other
reproductive harm.

CONGRATULATIONS

Congratulations on acquiring your new Mercury. Please take the time to
get well acquainted with your vehicle by reading this handbook. The
more you know and understand about your vehicle the greater the safety
and pleasure you will derive from driving it.

For more information on Ford Motor Company and its products visit the
following website:

• In the United States: www.ford.com

• In Canada: www.ford.ca

• In Mexico: www.ford.com.mx

• In Australia: www.ford.com.au

Additional owner information is given in separate publications.
This Owner’s Guide describes every option and model variant available

and therefore some of the items covered may not apply to your
particular vehicle. Furthermore, due to printing cycles it may describe
options before they are generally available.

Remember to pass on the Owner’s Guide when reselling the vehicle. It is
an integral part of the vehicle.

4

Introduction

Fuel pump shut-off switch In the event of an accident the

safety switch will automatically cut off the fuel supply to the
engine. The switch can also be activated through sudden vibration (e.g.
collision when parking). To reset the switch, refer to the Fuel pump
shut-off switch in the Roadside emergencies chapter.

SAFETY AND ENVIRONMENT PROTECTION

Warning symbols in this guide

How can you reduce the risk of personal injury and prevent possible
damage to others, your vehicle and its equipment? In this guide, answers
to such questions are contained in comments highlighted by the warning
triangle symbol. These comments should be read and observed.

Warning symbols on your vehicle

When you see this symbol, it is
imperative that you consult the
relevant section of this guide before
touching or attempting adjustment
of any kind.

Protecting the environment

We must all play our part in
protecting the environment. Correct
vehicle usage and the authorized
disposal of waste cleaning and
lubrication materials are significant
steps towards this aim. Information in this respect is highlighted in this
guide with the tree symbol.

5

Introduction

BREAKING-IN YOUR VEHICLE

Your vehicle does not need an extensive break-in. Try not to drive
continuously at the same speed for the first 1,600 km (1,000 miles) of
new vehicle operation. Vary your speed to allow parts to adjust
themselves to other parts.

Drive your new vehicle at least 800 km (500 miles) before towing a
trailer.

Do not add friction modifier compounds or special break-in oils during
the first few thousand kilometers (miles) of operation, since these
additives may prevent piston ring seating. See Engine oil in the
Maintenance and specifications chapter for more information on oil
usage.

SPECIAL NOTICES
Emission warranty

The New Vehicle Limited Warranty includes Bumper-to-Bumper
Coverage, Safety Restraint Coverage, Corrosion Coverage, and 7.3L
Power Stroke Diesel Engine Coverage. In addition, your vehicle is eligible
for Emissions Defect and Emissions Performance Warranties. For a
detailed description of what is covered and what is not covered, refer to
the Warranty Guide that is provided to you along with your Owner’s
Guide.

Data Recording

Computers in your vehicle are capable of recording detailed data
potentially including but not limited to information such as:

• the use of restraint systems including seat belts by the driver and
passengers,

• information about the performance of various systems and modules in
the vehicle, and

• information related to engine, throttle, steering, brake or other system
status.

6

Introduction

Any of this information could potentially including information regarding
how the driver operates the vehicle potentially including but not limited
to information regarding vehicle speed, brake or accelerator application
or steering input. This information may be stored during regular
operation or in a crash or near crash event.

This stored information may be read out and used by:

• Ford Motor Company.

• service and repair facilities.

• law enforcement or government agencies.

• others who may assert a right or obtain your consent to know such

information.

Special instructions

For your added safety, your vehicle is fitted with sophisticated electronic
controls.

Please read the section Supplemental Restraint System (SRS)
in the Seating and safety restraints chapter. Failure to follow

the specific warnings and instructions could result in personal injury.

Front seat mounted rear facing child or infant seats should
NEVER be used in front of a passenger side air bag unless the

air bag can be and is turned OFF.

Notice to owners of Severe Duty vehicles

Before you drive your vehicle, be sure to read the “Severe Duty Owner’s
Guide Supplement.” This book contains important operation and
maintenance information.

7

Introduction

These are some of the symbols you may see on your vehicle.

Vehicle Symbol Glossary

Safety Alert

Fasten Safety Belt Air Bag-Front

Air Bag-Side Child Seat

Child Seat Installation
Warning

Child Seat Tether
Anchor

Anti-Lock Brake System

Traction Control AdvanceTrac

Master Lighting Switch Hazard Warning Flasher

Fog Lamps-Front Fuse Compartment

See Owner’s Guide

Child Seat Lower
Anchor

Brake System

Brake Fluid ­Non-Petroleum Based

Fuel Pump Reset Windshield Wash/Wipe

Windshield
Defrost/Demist

8

Rear Window
Defrost/Demist

Vehicle Symbol Glossary

Introduction

Power Windows
Front/Rear

Child Safety Door
Lock/Unlock

Power Window Lockout

Interior Luggage
Compartment Release
Symbol

Panic Alarm Engine Oil

Engine Coolant

Engine Coolant
Temperature

Do Not Open When Hot Battery

Avoid Smoking, Flames,
or Sparks

Battery Acid

Explosive Gas Fan Warning

Power Steering Fluid

Maintain Correct Fluid
Level

Emission System Engine Air Filter

MAX

MIN

Passenger Compartment
Air Filter

Check fuel cap Low tire warning

Jack

9

Instrument Cluster

WARNING LIGHTS AND CHIMES

Warning lights and gauges can alert you to a vehicle condition that may
become serious enough to cause expensive repairs. A warning light may
illuminate when a problem exists with one of your vehicle’s functions.
Many lights will illuminate when you start your vehicle to make sure the
bulb works. If any light remains on after starting the vehicle, have

the respective system inspected immediately.

Check engine

Illuminates briefly to ensure the
system is functional. If it comes on
after the engine is started, one of
the engine’s emission control
systems may be malfunctioning. The
light may illuminate without a driveability concern being noted and will
not require towing.

Light remains on:

Temporary malfunctions may cause your light to illuminate. Examples
are:

1. The vehicle has run out of fuel.

2. Poor fuel quality or water in the fuel.

3. The fuel cap may not have been properly installed and securely

tightened.
These temporary malfunctions can be corrected by filling the fuel tank

with high quality fuel of the recommended octane and/or properly
installing and securely tightening the fuel cap. After three driving cycles
without these or any other temporary malfunctions present, the light

CHECK

ENGINE

10

Instrument Cluster

should turn off. (A driving cycle consists of a cold engine startup
followed by mixed city/highway driving.) No additional vehicle service is
required.

If the light remains on, have your vehicle serviced at the first available
opportunity.

Light is blinking:

Engine misfire is occurring which could damage your catalytic converter.
You should drive in a moderate fashion (avoid heavy acceleration and
deceleration) and have your vehicle serviced at the first available
opportunity.

Under engine misfire conditions, excessive exhaust temperatures
could damage the catalytic converter, the fuel system, interior

floor coverings or other vehicle components, possibly causing a fire.

Check fuel cap

Illuminates when the fuel cap is not
installed correctly. Check the fuel
cap for proper installation. When
the fuel filler cap is properly
re-installed, the light(s) will turn off
after a period of normal driving. Continuing to operate the vehicle with
the check fuel cap light on, or a mis-installed fuel cap can activate the
Service Engine Soon/Check Engine warning light.

It may take a long period of time for the system to detect an
improperly installed fuel filler cap.

For more information, refer to Fuel filler cap in the Maintenance and
specifications chapter.

CHECK

FUEL

CAP

Brake system warning

To confirm the brake system
warning light is functional, it will
momentarily illuminate when the
ignition is turned to the ON position
(alternatively for some vehicles
when the ignition is moved from the ON position to START position, the
light will momentarily illuminate prior to reaching the START position).
It also illuminates if the parking brake is engaged. If the brake system
warning light does not illuminate as described, seek service immediately.

!

BRAKE

11

Instrument Cluster

Illumination after the parking brake is released indicates low brake fluid
level or a brake system malfunction and the brake system should be
serviced immediately by a qualified technician.

Refer to Brakes in the Driving chapter for more information.

Anti-lock brake system (ABS)

To confirm the anti-lock brake
system (ABS) warning light is
functional it will momentarily
illuminate when the ignition is
turned to the ON position
(alternatively for some vehicles when the ignition is moved from the ON
position to the START position, the light will momentarily illuminate just
prior to reaching the START position). If the light remains on, continues
to flash or fails to illuminate, have the ABS serviced immediately. If the
ABS light remains on, it means the anti-lock brake system has
malfunctioned and is disabled, however, the normal brake system will
still function unless the brake warning light also remains illuminated and
parking brake is off. Refer to Brakes in the Driving chapter for more
information.

Safety belt

Illuminates to remind you to fasten
your safety belts. For more
information, refer to the Seating
and safety restraints chapter.

ABS

Air bag readiness

Illuminates to confirm that the air
bags (front or side) are operational.
If the light fails to illuminate,
continues to flash or remains on,
have the system serviced immediately.

Charging system

Illuminates when the battery is not
charging properly.

12

AIR

BAG

Instrument Cluster

Engine coolant temperature

Illuminates when the engine coolant
temperature is high. Stop the
vehicle as soon as safely possible,
switch off the engine and let it cool.

Never remove the coolant recovery cap while the engine is
running or hot.

Refer to Engine coolant in the Maintenance and specifications
chapter. If light stays on or continues to turn on after the vehicle warms
up, have your vehicle serviced.

Traction ControlY active (if equipped)

Illuminates when the Traction
Controly system is active. It will be
lit for a minimum of four seconds or
for the duration of the Traction
Controly event.

For more information, refer to the
Driving chapter.

Air suspension

Illuminates when the air suspension
switch is turned OFF, the load limit
is exceeded or the air suspension
system requires servicing.

Low fuel

Illuminates when the fuel level in
the fuel tank is at, or near, empty
(refer to Fuel gauge in this chapter
for more information).

AIR

SUSP

LOW

FUEL

O/D off

Illuminates when the overdrive
function has been turned OFF using
the Transmission Control Switch
(TCS) on the gearshift. If the light
does not come on or the light flashes steadily, have your vehicle serviced
as soon as possible, damage to the transmission could occur.

O/D

OFF

13

Instrument Cluster

Turn signals

Illuminates when the turn signals or
the hazard lights are turned on. If
the lights stay on continuously or
flash faster, check for a burned-out bulb.

High beams

Illuminates when the high beam
headlamps are turned on.

Safety belt warning chime

Sounds to remind you to fasten your safety belts.

BeltMinderY chime

Sounds intermittently to remind you to fasten your safety belts.

Supplemental restraint system (SRS) warning chime

Sounds when a malfunction in the supplemental restraint system (front
or side airbags) has been detected. Have the supplemental restraint
system inspected immediately.

Headlamps on warning chime

Sounds when the headlamps or parking lamps are on, the key is removed
from the ignition and the driver’s door is opened.

Key-in-ignition warning chime

Sounds when the key is left in the ignition and the driver’s door is
opened.

14

GAUGES

Engine coolant temperature gauge

Indicates the temperature of the
engine coolant. At normal operating
temperature, the needle remains
within the normal area (the area
between the “H” and “C”). If it
enters the red section, the engine is
overheating. Stop the vehicle as
soon as safely possible, switch off
the engine immediately and let the
engine cool. Refer to Engine

coolant in the Maintenance and
specifications chapter.

Instrument Cluster

H

C

Never remove the coolant reservoir cap while the engine is
running or hot. Steam and scalding liquid from a hot cooling

system can burn you badly.

This gauge indicates the temperature of the engine coolant, not the
coolant level. If the coolant is not at its proper level the gauge indication
will not be accurate.

15

Instrument Cluster

Engine oil pressure gauge

Located in the lower center of the
instrument panel, indicates engine
oil pressure. If the pointer drops
below the normal operating range
(50–75 psi) or the minimum low (6
psi) pressure when the engine is
running, stop your vehicle as soon
as possible, shut off the engine and
check the oil level. Add oil if
necessary.

Do not continue to operate your
engine as long as the pointer is out of the normal operating range.
Otherwise, your engine may be severely damaged.

If the gauge indicates zero or very low oil pressure (needle drops
below “0”) stop the vehicle and engine as soon as safe to do so
and check the engine oil level.

After running, the engine may be hot. Allow the engine to cool
before handling any components.

Voltmeter gauge

Located in the lower center of the
instrument panel, measures the
battery charging voltage. If the
meter consistently indicates less
than 13.0 volts or more than 15.0
volts under normal vehicle
operation, have your vehicle’s
electrical system checked.

16

Instrument Cluster

Fuel gauge

Displays approximately how much
fuel is in the fuel tank. The fuel
gauge may vary slightly when the
vehicle is in motion or on a grade.

When refueling the vehicle from
empty indication, the amount of fuel
that can be added will be less than
the advertised capacity due to the
reserve fuel.

The FUEL DOOR icon and arrow
indicates which side of the vehicle the fuel filler door is located.

Speedometer

Indicates the current vehicle speed.

Odometer

Registers the total kilometers
(miles) of the vehicle.

17

Instrument Cluster

Trip odometer

Registers the kilometers (miles) of
individual journeys. To reset,
depress the control.

Tachometer

Indicates the engine speed in
revolutions per minute.

Driving with your tachometer
pointer continuously at the top of
the scale may damage the engine.

18

Entertainment Systems

AUDIOPHILE AM/FM STEREO/CASSETTE/SINGLE CD

1. Tape eject control

2. CD eject control

3. Bass/treble control

4. Balance/fade control

5. Compression/shuffle control

6. Select control

7. Side direction/Dolby control

8. Rewind/fast forward control

9. RDS/DSP control

10. Autoset control

Volume/power control

Press the control to turn the audio
system on or off.

Audio power can also be turned on
by pressing the AM/FM select
control or the TAPE/CD select control.

11. Scan control

12. Seek control

13. Tune control

14. AM/FM/CD control

15. Phone/mute control

16. Power/volume control

17. Tape control

18. CD door

19. Cassette door

19

Entertainment Systems

Turn control to raise or lower
volume.

If the volume is set above a certain level and the ignition is turned off,
the volume will come back on at a “nominal” listening level when the
ignition switch is turned back on.

Bass adjust

The bass adjust control allows you
to increase or decrease the audio
system’s bass output.

Press the BASS control then press:

•

•

Treble adjust

The treble adjust control allows you
to increase or decrease the audio
system’s treble output.

Press the TREB control then press:

•

•

to decrease the bass output

and

to increase the bass output.

to decrease the treble output

and

to increase the treble output.

Speaker balance adjust

Speaker sound distribution can be
adjusted between the right and left
speakers.

20

Entertainment Systems

Press the BAL control then press:

•

•

Speaker fade adjust

Speaker sound can be adjusted
between the front and rear
speakers.

Press the FADE control then press:

•

•

Seek function

The seek function control works in radio, tape or CD mode.

Seek function in radio mode

• Press to find the next

• Press

Seek function in tape mode

• Press to listen to the previous selection on the tape.

• Press

to shift sound to the left and
to shift sound to the right.

to shift the sound to the

front and

to shift the sound to the rear.

listenable station down the
frequency band.

to find the next
listenable station up the
frequency band.

to listen to the next selection on the tape.

Seek function in CD mode

• Press to seek to the previous
track of the current disc.

• Press
next track of the current disc.
After the last track has been
completed, the first track of the current disc will automatically replay.

to seek forward to the

21

Entertainment Systems

Scan function

The scan function works in radio,
tape or CD mode.

Scan function in radio mode

Press the SCAN control to hear a brief sampling of all listenable stations
on the frequency band. Press the control again to stop the scan mode.

Scan function in tape mode

Press the SCAN control to hear a short sampling of all selections on the
tape. (The tape scans in a forward direction. At the end of the tape’s
first side, direction automatically reverses to the opposite side of the
tape.) To stop on a particular selection, press the control again.

Scan function in CD mode

Press the SCAN control to hear a short sampling of all selections on the
CD. (The CD scans in a forward direction, wrapping back to the first
track at the end of the CD.) To stop on a particular selection, press the
control again.

AM/FM select

The AM/FM select control works in
radio, tape and CD modes.

AM/FM select in radio mode

This control allows you to select AM or FM frequency bands. Press the
control to switch between AM, FM1 or FM2 memory preset stations.

AM/FM select in tape mode

Press this control to stop tape play and begin radio play.

Radio station memory preset

The radio is equipped with six station memory preset controls. These
controls can be used to select up to six preset AM stations and twelve
FM stations (six in FM1 and six in FM2).

22

Entertainment Systems

Setting memory preset stations

1. Select the frequency band with

the AM/FM select control.

2. Select a station. Refer to Tune

adjust or Seek function for more information on selecting a station.

3. Press and hold a memory preset control until the sound returns,

indicating the station is held in memory of the control you selected.

Autoset memory preset

Autoset allows you to set strong radio stations without losing your
original manually set preset stations. This feature is helpful on trips
when you travel between cities with different radio stations.

Starting autoset memory preset

1. Select a frequency using the AM/FM select controls.

2. Press the control.

3. When the first six strong stations

are filled, the station stored in
memory preset control 1 will start
playing.

If there are less than six strong stations available on the frequency band,
the remaining memory preset controls will all store the last strong
station available.

These stations are temporarily stored in the memory preset controls
(until deactivated) and are accessed in the same manner as your original
presets.

To deactivate autoset and return to your audio system’s manually set
memory stations, press the AUTO control again.

23

Entertainment Systems

Setting the clock with radio data system (RDS) feature

Press the RDS control until SELECT
HOUR or SELECT MINS is
displayed.

Use the SEL control to manually set
the time.

•

•

Tune adjust

The tune control works in radio mode.

Tune adjust in radio mode

• Press to move to the next

• Press

to decrease hours/minutes

and

to increase hours/minutes.

frequency down the band
(whether or not a listenable
station is located there). Hold the
control to move through the
frequencies quickly.

to move to the next frequency up the band (whether or not

a listenable station is located there). Hold for quick movement.

Tape/CD select

• To begin tape play (with a tape
loaded into the audio system)
while in the radio or CD mode,
press the TAPE control. Press the
button during rewind or fast forward to stop the rewind or fast
forward function.

• To begin CD play (if CD is
loaded), press the CD control.
The first track of the disc will
begin playing. If returning from
radio or tape mode, CD play will begin where it stopped last.

24

Entertainment Systems

Rewind

The rewind control works in tape
and CD modes.

• In tape mode, radio play will
continue until rewind is stopped
(with the TAPE control) or the beginning of the tape is reached.

• In CD mode, pressing the REW control rewinds the CD within the
current track.

Fast forward

The fast forward control works in
tape and CD modes.

• In the tape mode, radio play will
continue until the fast forward
function is stopped (with the tape control) or tape direction will
automatically reverse when the end of the tape is reached.

• In CD mode, pressing the control fast forwards the CD within the
current track.

Tape direction select

Press to play the alternate side of
the tape.

Eject function

Press the EJ control to stop and
eject a tape.

Press the EJ control to stop and
eject a CD.

DolbyT noise reduction

Dolbyt noise reduction operates in
tape mode. Dolbyt noise reduction
reduces the amount of hiss and
static during tape playback.

25

Entertainment Systems

Press the control to activate (and deactivate) the Dolbyt noise
reduction.

Dolbyt noise reduction is manufactured under license from Dolbyt
Laboratories Licensing Corporation. “Dolbyt” and the double-D
symbol
Corporation.

Compression adjust

Compression adjust brings soft and
loud CD passages together for a
more consistent listening level.

Press the COMP control to activate
and deactivate compression adjust.

Radio data system (RDS) feature

This feature allows your audio system to receive station identification or
program type from RDS-equipped FM radio stations.

The Federal Communications Commission (FCC) and the Canadian Radio
and Telecommunications Commission (CRTC) recommend that FM radio
broadcasters use RDS technology to transmit information. FM radio
stations are independently operated and individually elect to use RDS
technology to transmit station ID and program type as desired.

Press the RDS control until RDS ON
or RDS OFF appears in the display.
Use the SEL control to enable (ON)
or disable (OFF) the feature. With the RDS activated, press the SEL
control to scroll through the following selections:

Traffic

• Press the RDS control until
TRAFFIC is displayed.

are registered trademarks of Dolbyt Laboratories Licensing

• Use the SEL control to select ON
or OFF. With the feature on, use
the SEEK or SCAN control to
find a radio station broadcasting a
traffic report (if it is broadcasting
RDS data).

26

Entertainment Systems

This feature also allows you to control the volume of traffic
announcements. With the display reading TRAFFIC ON, adjust the
volume (using the volume control) to the desired level. The volume level
will show at the bottom of the display. Interrupting traffic
announcements will be at the selected volume level.

Traffic information is not available in most U.S. markets.

Program type

• Press the RDS control until the
FIND program type is displayed.

• Use the SEL control to select the
program type. With the feature
on, use the SEEK or SCAN
control to find the desired
program type from the following
selections:

• Classic

• Country

• Info

• Jazz

• Oldies

Show

• With RDS activated, press the
RDS control until SHOW is
displayed.

• Use the SEL control to select
TYPE (the display shows the
program type), NAME (the
display shows the call letters of
the station) or NONE.

• R&B

• Religious

• Rock

• Soft

• Top 40

Shuffle feature

The shuffle feature operates in CD
mode and plays all tracks in random
order.

Press the SHUFFLE control to start
this feature. Random order play will continue until the SHUFFLE control
is pressed again.

27

Entertainment Systems

Mute mode

Press the MUTE control to mute the
playing media. Press the MUTE
control again to return to the
playing media.

Digital signal processing

The digital signal processing (DSP)
feature allows you to change the
signal mode to suit your listening
tastes.

These effects will change the sound quality and may need to be adjusted
based upon the program material to suit your listening needs.

Press the control to turn the feature on or off.
Press the DSP control to adjust the occupancy modes:

• ALL SEATS

• DRIVER SEAT

• REAR SEATS

Use the SELECT control to change
the equalization to the desired
mode.

CD CHANGER (IF EQUIPPED)

The CD changer is located in the trunk.

1. Slide the door to access the CD

changer magazine.

28

2. Press to eject the magazine.

Entertainment Systems

3. Turn the magazine (A) over.

4. Using the disc holder release

knob (C), pull the disc holder (B)
out of the magazine.

If you pull too hard on the disc holder, the disc holder may come
completely out of the magazine. If this happens, reinsert the disc holder
back into the magazine while pressing on the lever (A).

A

A

B

C

29

Entertainment Systems

5. Line up the CD with the groove

of the disc holder. Ensure that the
label on the CD faces downwards.

6. Press in on the disc holder until it

locks securely into the magazine. If
the disc holders are not fully locked
into the magazine, the unit will not
operate.

Ensure that the disc holder is
evenly inserted and at the same
level as the magazine (A). The unit
will not operate if the disc holder is
not inserted at the same level (B).

Radio power must be turned on to play the CDs in the changer. The
magazine may be stored in the glove box when not being used.

The CD magazine may be inserted or ejected with the radio power off.
ONLY use the magazine supplied with the CD changer, other types will

damage the unit.
Keep the CD changer door closed. Coins and foreign objects will damage

the CD player and void your audio system warranty.

Do not insert any promotional (odd shaped or sized) discs, or
discs with removable labels into the CD player as jamming may
occur.

A

B

TROUBLESHOOTING THE CD CHANGER (IF EQUIPPED)

The laser beam used in the compact disc player is harmful to the
eyes. Do not attempt to disassemble the case.

If sound skips:

• You may be traveling on a rough road, playing badly scratched discs or
the disc may be dirty. Skipping will not scratch the discs or damage
the player.

30

Entertainment Systems

If your changer does not work, it may be that:

• A disc is already loaded where you want to insert a disc.

• The disc is inserted with the label surface downward.

• The disc is dusty or defective.

• The player’s internal temperature is above 60°C (140°F). Allow the

player to cool down before operating.

• A disc with format and dimensions not within industry standards is
inserted.

CLEANING COMPACT DISCS

Inspect all discs for contamination before playing. If necessary, clean
discs only with an approved CD cleaner and wipe from the center out to
the edge. Do not use circular motion.

CD AND CD CHANGER CARE

• Handle discs by their edges only. Never touch the playing surface.

• Do not expose discs to direct sunlight or heat sources for extended

periods of time.

• Do not insert more than one disc into each slot of the CD changer
magazine.

CD units are designed to play commercially pressed 12 cm (4.75
in) audio compact discs only. Due to technical incompatibility,
certain recordable and re-recordable compact discs may not
function correctly when used in Ford CD players. Irregular
shaped CDs, CDs with a scratch protection film attached, and CDs
with homemade paper (adhesive) labels should not be inserted
into the CD player. The label may peel and cause the CD to
become jammed. It is recommended that homemade CDs be
identified with permanent felt tip marker rather than adhesive
labels. Ball point pens may damage CDs. Please contact your
dealer for further information.

CLEANING CASSETTE PLAYER (IF EQUIPPED)

Clean the tape player head with a cassette cleaning cartridge after 10 to
12 hours of play in order to maintain the best sound and operation.

CASSETTE AND CASSETTE PLAYER CARE

• Use only cassettes that are 90 minutes long or less.

• Do not expose tapes to direct sunlight, high humidity, extreme heat or

extreme cold. Allow tapes that may have been exposed to extreme
temperatures to reach a moderate temperature before playing.

31

Entertainment Systems

• Tighten very loose tapes by inserting a finger or pencil into the hole
and turning the hub.

• Remove loose labels before inserting tapes.

• Do not leave tapes in the cassette player for a long time when not

being played.

RADIO FREQUENCY INFORMATION

The Federal Communications Commission (FCC) and the Canadian Radio
and Telecommunications Commission(CRTC) establish the frequencies
AM and FM stations may use for their broadcasts. Allowable frequencies
are:

AM 530, 540–1600, 1610 kHz
FM 87.7, 87.9–107.7, 107.9 MHz
Not all frequencies are used in a given area.

RADIO RECEPTION FACTORS

Three factors can affect radio reception:

• Distance/strength. The further an FM signal travels, the weaker it is.
The listenable range of the average FM station is approximately 40 km
(24 miles). This range can be affected by “signal modulation.” Signal
modulation is a process radio stations use to increase their
strength/volume relative to other stations.

• Terrain. Hills, mountains and tall buildings between your vehicle’s
antenna and the radio station signal can cause FM reception problems.
Static can be caused on AM stations by power lines, electric fences,
traffic lights and thunderstorms. Moving away from an interfering
structure (out of its “shadow”) returns your reception to normal.

• Station overload. Weak signals are sometimes captured by stronger
signals when you pass a broadcast tower. A stronger signal may
temporarily overtake a weaker signal and play while the weak station
frequency is displayed.

The audio system automatically switches to single channel reception if it
will improve the reception of a station normally received in stereo.

AUDIO SYSTEM WARRANTIES AND SERVICE

Refer to the Warranty Guide for audio system warranty information.
If service is necessary, see your dealer or a qualified technician.

32

Climate Controls

ELECTRONIC AUTOMATIC TEMPERATURE CONTROL (EATC)
SYSTEM

The EATC system will maintain a
selected temperature and
automatically control the fan speed
and airflow location.

F

OUTSIDE TEMP AUTOMATIC

NORM A/C

MAX A/C

AUTO

VENT FLOOR FLR • DEF DEF

OFF

Automatic operation

Press AUTOMATIC and select the desired temperature. The selected
temperature and the word AUTO will appear in the display window. The
EATC system will either heat or cool to achieve the selected
temperature. The system will automatically determine fan speed, airflow
location and if outside air or recirculated air is required. Fan speed
remains automatic unless the fan speed thumbwheel is turned or the
steering wheel fan speed control (if equipped) is pressed.

When in automatic operation and weather conditions require heat, the
air will be sent to the floor ducts. However, until the engine has warmed,
the fan will operate at a low speed and airflow will be directed to the
windshield defroster ducts. Upon engine warm up, the system will
automatically direct airflow to the floor ducts and operate the required
fan speed to achieve the selected temperature.

If unusual conditions exist (i.e.-window fogging, etc.), the manual
overrides allow you to select airflow locations and the fan speed. To
return to automatic operation, press Automatic/AUTO.

HI

LO

Temperature selection

The control the temperature, select
the desired temperature by pressing
the temperature controls.

F

˚

AUTO

33

Climate Controls

For continuous maximum cooling,
push the blue button until 16°C
(60°F) is shown in the display
window. The EATC will continue
maximum cooling (disregarding the
displayed temperature) until a
warmer temperature is selected by
pressing the red control.

For continuous maximum heating, push the red button until 32°C (90°F)
is shown in the display window. The EATC will continue maximum
heating (disregarding the displayed temperature) until a cooler
temperature is selected by pressing the blue control.

Temperature conversion

Press MAX A/C and DEF

at
the same time (for one second) to
switch between Fahrenheit and
Celsius.

If your vehicle has an English/Metric (E/M) control to change your
electronic instrument cluster display (if equipped) and the message
center display (if equipped) from English to Metric, this control will also
change the temperature display. Refer to Electronic Message Center in
the Driver Controls Chapter.

Displaying outside temperature

Press OUTSIDE TEMP to display
the outside air temperature. It will
be displayed until OUTSIDE TEMP
is pressed again.

OUTSIDE TEMP

VENT PNL • FLRMAX A/C

OUTSIDE TEMP AUTOMATIC

NORM A/C

MAX A/C

OUTSIDE TEMP

AUTO

VENT FLOOR FLR • DEF DEF

OFF

HI

LO

If the selected temperature is changed while the outside temperature is
displayed, the new temperature will be displayed for four seconds after it
is changed, then the outside temperature will return to the window.

34

NORM A/C

VENTMAX A/C

Climate Controls

If a manual override function is selected while the outside temperature is
displayed, the new function will be displayed for four seconds after it is
changed, then the outside temperature will return to the window along
with the override selection.

The outside temperature reading is most accurate when the vehicle is
moving. Higher readings may be obtained when the vehicle is not
moving. The readings that you get may not agree with temperatures
given on the radio due to differences in vehicle and station locations.

Fan speed (

)

When AUTOMATIC is pressed, fan
speed is adjusted automatically for
existing conditions. You can override

OFF

HI

fan speed at any time. To control
fan speed manually, use the

AUTOMATIC

thumbwheel to cancel automatic fan
speed operation. Rotate the
thumbwheel or press the steering

FLR • DEF DEF

LO

wheel controls (if equipped) up for
higher fan speed or down for lower
fan speed.

The display will show
indicate manual fan operation.

to

F

˚

AUTO

To return to automatic fan operation, press AUTOMATIC.

Manual override controls

The manual override controls allow
you to determine airflow location
and fan speed. To return to full
automatic control, press

F

OUTSIDE TEMP AUTOMATIC

NORM A/C

MAX A/C

AUTO

VENT FLOOR FLR • DEF DEF

OFF

Automatic/AUTO.

• Max A/C - Distributes recirculated air through the instrument panel

registers. A temperature of 16°C (60°F) will appear in the display
window until Automatic/AUTO, another manual override control, or
the temperature control has been selected. The A/C compressor will
only function if the outside temperature is above approximately 2°C
(36°F). Max A/C is noisier than Norm A/C, but more economic and
efficient. This mode will reduce undesirable odors from entering the
vehicle.

HI

LO

35

Climate Controls

• Norm A/C- Distributes outside air through the instrument panel

registers. The A/C compressor will only function if the outside
temperature is above approximately 2°C (36°F). Norm A/C is more
quiet than Max A/C, but not as economic and efficient.

• Vent-Distributes outside air through the instrument panel registers.

The air cannot be cooled below the outside temperature.

• Floor- Distributes outside air through the floor ducts. The air cannot

be cooled below the outside temperature.

• Floor & Defrost - Distributes outside air through the windshield

defroster ducts, floor ducts and the side window demisters. The A/C
compressor will operate automatically if the outside temperature is
above approximately 2°C (36°F). The air distributed through the floor
ducts will be slightly warmer than that sent to the windshield
defroster ducts and the side window demisters.

• Defrost - Distributes outside air through the windshield defroster

ducts and the side window demisters. The A/C compressor will
operate automatically if the outside temperature is above
approximately 2°C (36°F). This mode will clear ice and fog from the
windshield.

Operating tips

• To reduce fogging under humid weather conditions, place the climate

control system in Defrost and Rear Defrost (if equipped) mode before
driving.

• To reduce humidity buildup inside the vehicle: Do not drive with the

climate control system in Off mode. Do not drive with the climate
control system in Max A/C mode (if equipped).

• Under normal weather conditions, do not leave your vehicle in Max

A/C (if equipped), recirculation control (if equipped) or Off mode
when turning off the ignition.

• Under snowy or dirty weather conditions, leave your vehicle in Max

A/C (if equipped), recirculation control (if equipped), or Off mode
when turning off the ignition.

• Remove any snow, ice or leaves from the exterior base of the

windshield.

• To increase the efficiency of the A/C (if equipped), drive with the

windows slightly open for 2–3 minutes or until the vehicle has been
“aired” out.

• Do not place objects under the front seat or over the defroster ducts.

They may reduce visibility, fall into the ducts, or degrade the
performance of your climate control system.

36

Climate Controls

To aid in side window defogging/demisting in cold weather conditions:

1. Select VENT

2. Set the temperature control to full heat

3. Set the fan speed to HI

4. Direct the outer panel vents towards to side windows
To increase airflow to the outer panel vents, close the central panel

vents.

Do not place objects on top of the instrument panel, as these
objects may become projectiles in a collision or sudden stop.

REAR WINDOW DEFROSTER

The rear defroster control is located
on the instrument panel.

Press the rear defroster control to
clear the rear window of thin ice
and fog.

• A small LED will illuminate when

the rear defroster is activated.

The ignition must be in the ON position to operate the rear window
defroster.

The defroster turns off automatically after 10 minutes or when the
ignition is turned to the OFF position. To manually turn off the defroster
before 10 minutes have passed, push the control again.

Activating the rear window defroster will also activate the heated mirrors
(if equipped). For more information refer to Heated outside mirrors in
the Driver controls chapter.

37

Lights

HEADLAMP CONTROL

Turns the lamps off.

Turns on the parking
lamps, instrument panel lamps,
license plate lamps and tail lamps.

Turns the headlamps on.

Your vehicle’s headlamp system is equipped with a feature that will not
dim the instrument panel lighting when the headlamps are on in the
daytime. Even during full daylight, the instrument panel lighting will still
be visible with the headlamp operating.

Autolamp control

The autolamp system provides light
sensitive automatic on-off control of
the exterior lights normally
controlled by the headlamp control.

The autolamp system also keeps the
lights on for a predetermined period
of time after the ignition switch is
turned to OFF.

• To turn autolamps on, rotate the

control counterclockwise to the
next position from OFF.

• To turn autolamps off, rotate the control clockwise past OFF to the

parking lamp position

The headlamps will also turn on when the windshield wipers are
activated, after a 10–20 second delay.

, then back to OFF.

38

Lights

Foglamp control

The foglamps can be turned on
when the headlamp control is pulled
toward you and is in any of the
following positions:

• Parking lamps

• Low beams

• Autolamps

Daytime running lamps (DRL) (if equipped)

Turns the lowbeam headlamps on with a reduced output. To activate:

• the key must be in the ON position,

• the parking brake released, and

• the headlamp control is in the OFF or Parking lamps position.

Always remember to turn on your headlamps at dusk or during

inclement weather. The Daytime Running Light (DRL) System
does not activate your tail lamps and generally may not provide
adequate lighting during these conditions. Failure to activate your
headlamps under these conditions may result in a collision.

High beams

Push the lever toward the
instrument panel to activate. Pull
the lever towards you to deactivate.

39

Lights

Flash to pass

Pull toward you slightly to activate
and release to deactivate.

PANEL DIMMER CONTROL

Use to adjust the brightness of the
instrument panel during headlight
and parklamp operation.

• Rotate the thumbwheel from left
to right to brighten the
instrument panel.

• Rotate the thumbwheel from right
to left to dim the instrument
panel.

Domelamp Control

The panel dimmer control also controls the domelamp operation.

• Rotate the thumbwheel fully to the right, past detent to activate the
domelamp.

• In order to turn off the domelamp, rotate the thumbwheel to the left.

AIMING THE HEADLAMPS

The headlamps on your vehicle are properly aimed at the assembly plant.
If your vehicle has been in an accident the alignment of your headlamps
should be checked by a qualified service technician.

Vertical aim adjustment

1. Park the vehicle on a level surface approximately 7.6 meters (25 feet)

from a vertical wall or screen directly in front of it.

40

Lights

• (1) Eight feet

• (2) Center height of lamp to

ground

• (3) Twenty five feet

• (4) Horizontal reference line

2. Measure the height of the headlamp bulb center from the ground and

mark a 2.5 meter (8 foot) horizontal reference line on the vertical wall or
screen at this height (a piece of masking tape works well).

3. Turn on the low beam headlamps to illuminate the wall or screen and

open the hood.

4. On the wall or screen you will

observe an area of high intensity
light. The top of the high intensity
area should touch the horizontal
reference line, if not, the beam will
need to be adjusted.

To see a clearer light pattern for
adjusting, you may want to block
the light from one headlamp while
adjusting the other.

5. Locate the vertical adjuster on

each headlamp. Usinga4mm
wrench, turn the adjuster either
clockwise (to adjust down) or
counterclockwise (to adjust up).
The horizontal edge of the brighter
light should touch the horizontal
reference line.

6. HORIZONTAL AIM IS NOT REQUIRED FOR THIS VEHICLE AND IS

NON-ADJUSTABLE.

7. Close the hood and turn off the lamps.

41

Lights

TURN SIGNAL CONTROL

• Push down to activate the left
turn signal.

• Push up to activate the right turn
signal.

The flash rate of the turn signal will
speed up considerably if the left or
right turn lamp bulb (front or rear)
is burned out.

Cornering lamps

When the turn signal is used and the headlamps are on, the cornering
lamps will light either the right or left side depending on the direction of
the turn.

MAP/COURTESY LAMPS

Without a moon roof

With a moon roof

To turn on the map lamps, press the
map lamp control.

42

Lights

BULBS
Replacing exterior bulbs

Check the operation of all the bulbs frequently.

Using the right bulbs

Replacement bulbs are specified in the chart below. Headlamp bulbs
must be marked with an authorized “D.O.T.” for North America and an
“E” for Europe to assure lamp performance, light brightness and pattern
and safe visibility. The correct bulbs will not damage the lamp assembly
or void the lamp assembly warranty and will provide quality bulb burn
time.

Function Trade Number

Headlamp 9007
Park lamp and turn lamp (front) 3157 AK
Cornering lamp (front) 3156 K
Tail, stop and turn (rear) 3157 K
Backup lamp 3156 K
License plate lamp 168
High-mount brakelamp 912
Foglamps H1
Luggage compartment lamp 211-2
Dome lamp 906
Underhood lamp 211–2
Rear reading lamp 211-2
Map lamp 168
Illuminated visor mirror 168
Dual floorwell lamp 906
Glove compartment 168
All replacement bulbs are clear in color except where noted.
To replace all instrument panel lights - see your dealer.

Replacing the interior bulbs

Check the operation of all bulbs frequently.

43

Lights

Replacing headlamp bulbs

To remove the headlamp bulb:

1. Make sure the headlamp control is in the OFF position, then open the

hood

2. Remove the three pin type retainers and the radiator sight shield.

3. Disconnect the electrical

connector.

4. Remove the headlamp retainer

bolts and the headlamp assembly.

5. Remove the headlamp bulb

protective cover.

6. Remove the bulb retaining ring by

rotating it countercloskwise to free
it from the bulb socket and slide the
ring off of the plastic base. Keep the
ring to retain the new bulb.

7. Disconnect the electrical

connector from the bulb.

8. To install, reverse the removal

procedure. (Re-aiming the
headlamps may be necessary. For
additional information refer to the
headlamp aiming section of the
owner’s guide.)

Handle a halogen headlamp

bulb carefully and keep out
of children’s reach. Grasp the bulb
only by its plastic base and do not
touch the glass. The oil from your
hand could cause the bulb to
break the next time the
headlamps are operated.

Note: If the bulb is accidentally
touched, it should be cleaned with
rubbing alcohol before being used.

44

Lights

The headlamp bulb should not be removed from the headlamp until just
before a replacement bulb is installed. Removing the bulb for an
extended period of time may affect headlamp bulb performance.
Contaminants may enter the headlamp where they can settle on the lens
and reflector. Never turn the headlamps on with the bulb removed.

Replacing front parking lamp/turn signal bulbs

The park/turn lamp bulbs can be replaced with out removing the
headlamp assembly.

1. Make sure headlamp switch is in OFF position, then open the hood.

2. Remove the three pin type retainers and the radiator shield.

3. Remove the headlamp assembly retaining nuts, the side turn signal
lamp retaining nuts and the side turn signal assembly.

4. Remove the bulb from the side turn lamp assembly.

5. Disconnect the electrical connector from the bulb and replace the
bulb.

Note: The parking lamp/turn signal bulbs should not be removed from
the lamp until just before a replacement bulb is installed. Removing the
bulb for an extended period of time may affect headlamp bulb
performance. Contaminants may enter the headlamp where they can
settle on the lens and reflector. Never turn the lamps on with the bulb
removed.

6. To install, reverse the order of the removal procedure.

Replacing tail lamp/brake/turn lamp bulbs

The tail lamp, the brake lamp and the turn signal lamp bulbs are located
in the tail lamp assembly. Follow the same steps to replace either bulb.

45

Lights

1. Make sure headlamp switch is in
OFF position, then open the trunk
and carefully pull the carpet away to
expose the plastic retainer.

2. Remove plastic retainer to expose
the lamp assembly hardware.

3. Remove three nut and washer
assemblies and the lamp assembly
from the vehicle.

4. Remove the bulb socket by
rotating it counterclockwise, then
pulling it out of the lamp assembly.

5. Pull the bulb from the socket and
push in the new bulb.

6. Install the bulb socket into the
lamp assembly by rotating it
clockwise.

7. Install the lamp assembly on the
vehicle with three nut and washer
assemblies ensuring the washers on
the nuts are flush with the body to prevent water from entering the
trunk.

8. Install the plastic retainer and carefully push the carpet back in to
place.

46

Replacing foglamp bulbs

1. Remove the bulb socket from the
foglamp by turning
counterclockwise.

2. Disconnect the electrical
connector from the foglamp bulb.

3. Connect the new foglamp bulb to the electrical connector.

4. Install the bulb socket in the foglamp turning clockwise.

Replacing license plate lamp bulbs

1. Make sure headlamp switch is in
OFF position, then remove two
screws, grommets and the license
plate lamp assembly from the trunk
lid.

2. Carefully pull the bulb from the
socket and push in the new bulb.

3. Install the lamp assembly on
trunk lid with two grommets,
ensuring the grommets are pushed
all the way in to the trunk lid and secure with two screws.

Replacing backup lamp bulbs

1. Make sure headlamp switch is in
OFF position, then open trunk and
remove bulb socket from the trunk
lid by turning counterclockwise.

2. Pull the bulb straight out of the
socket and push in the new bulb.

3. Install the bulb socket in trunk lid
by turning clockwise.

Lights

47

Lights

Replacing high-mount brakelamp bulbs

1. Remove two screws from the
lamp assembly.

2. Carefully lift the lamp assembly
up for access to the bulbs.

3. Carefully pull the bulb socket out
of the lamp assembly.

4. Pull the bulb straight out of the
socket and push in the new bulb.

To install, reverse the removal
procedure.

48

Driver Controls

WINDSHIELD WIPER/WASHER CONTROLS

Rotate the windshield wiper control
to the desired interval, low or high
speed position.

The bars of varying length are for
intermittent wipers. When in this
position rotate the control upward
for fast intervals and downward for
slow intervals.

Push the end of the stalk to activate
washer. Push and hold for a longer
wash cycle.

Windshield wiper/washer features

The exterior lamps will illuminate after 10–20 second delay when the
ignition is ON and the windshield wiper control is in the LO or HI
position.

The lights will remain on for 30 seconds after the wipers are turned off.

Maintenance and care of windshield wiper blades

Check the wiper blades for wear at least twice a year or when they seem
less effective. Substances such as tree sap, road salt, oil film and some
hot wax treatments used by commercial car washes reduce the
effectiveness of wiper blades.

Operation of the wipers on dry glass for long periods of time may cause
deterioration of the wiper blades. Always use washer fluid when using
the wipers to remove salt or dirt from a dry windshield. Avoid using the
blades to remove frost or ice from the windshield. If the wiper blades are
frozen to the windshield, loosen the wiper blades before operating the
wipers to prevent damage to the wiper system.

It the windshield is not clear after using the windshield washer wiper
system, or if the wiper blades chatter, streak or smear when operating, it
is possible that wax, road salt or oil film may be on the windshield or the
wiper blades. Refer to Cleaning window and wiper blades in the
Cleaning chapter.

Changing the wiper blades

To make changing the wiper blades easy, turn the ignition to ACC, then
turn the wipers on. When the wipers reach the vertical position, turn the
ignition to LOCK.

49

Driver Controls

To replace the wiper blades:

1. Pull the wiper arm away from the
windshield and lock into the service
position.

2. Press and hold the tab on the
blade and slide the blade off the
wiper arm pin.

3. To attach the new wiper blade,
press and hold the tab on the blade
and slide the blade on to the wiper
arm pin. Then release the tab.

TILT STEERING

Pull the tilt steering control toward
you to move the steering wheel up
or down. Hold the control while
adjusting the wheel to the desired
position, then release the control.

Never adjust the steering wheel when the vehicle is moving.

50

Driver Controls

ILLUMINATED VISOR MIRROR

Lift the mirror cover to turn on the
visor mirror lamps.

OVERHEAD CONSOLE WITHOUT MOON ROOF (IF EQUIPPED)

The appearance of your vehicle’s overhead console will vary according to
your option package. Some of the features in the overhead console
include a storage bin and compass. To program the Homelinkt, refer to
Homelinkt Universal Transceiver it this chapter.

Storage compartment
(if equipped): Press the OPEN

control to open the storage
compartment. The door will open
slightly and can be moved to full
open.

The storage compartment may be
used to secure sunglasses or a
similar object.

Electronic compass display (if equipped)
Compass: The compass display is contained in the overhead console.

The vehicle heading is displayed as one of N, NE, E, SE, S, SW, W and
NW.

The compass reading may be affected when you drive near large
buildings, bridges, power lines and powerful broadcast antenna. Magnetic
or metallic objects placed in or on the vehicle may also affect compass
accuracy. Adjustments may need to be made to the zone and calibration
of the compass.

51

Driver Controls

Compass zone adjustment

1. Determine which magnetic zone
you are in by referring to the zone
map.

4

2. Turn the ignition to the ON
position.

5

3. Press and hold the MODE control
until VAR appears in the display,
then release. The display should
show the current zone number.

4. Press the MODE control until the
desired zone number appears. The
display will flash and then return to
normal operation. The zone is now
updated.

Compass calibration adjustment

Perform this adjustment in an open
area free from steel structures and
high voltage lines:

1. Press and hold the MODE control
until CAL appears in the display
(approximately eight seconds) and
release.

2. Drive the vehicle slowly (less
than 5 km/h [3 mph]) in circles until
CAL indicator turns off in about 2–3 complete circles.

3. The compass is now calibrated.

123

15
14

13
12

6 7 8 91011

OVERHEAD CONSOLE WITH MOON ROOF (IF EQUIPPED)

The appearance of your vehicle’s overhead console will vary according to
your option package. Some of the features in the overhead console
include Compass, Homelink, and Moon Roof controls.

52

Driver Controls

Compass mode

The compass reading may be affected when you drive near large
buildings, bridges, power lines and powerful broadcast antenna. Magnetic
or metallic objects placed in, on or near the vehicle may also affect
compass accuracy.

1. Turn ignition to the ON position.

2. Start the engine.

3. From a blank display press and
release the MODE button once. The
directional heading will be
displayed.

Note: If the compass is
de-calibrated, CAL will be displayed
in the right corner of the display.
Refer to “Calibration mode” in this
section for more details.

4. The overhead console displays the compass heading in one of eight
directions: NORTH, NORTHEAST, EAST, SOUTHEAST, SOUTH,
SOUTHWEST, WEST, and NORTHWEST.

Zone variation mode

Most geographic areas (zones) have a magnetic north compass point that
varies slightly from the northerly direction on maps. A correct zone
setting will eliminate compass heading error.

For optimum calibration, turn off all electrical accessories (heater/air
conditioning, wipers, etc.) and make sure all vehicle doors are shut.

To set the compass zone:

1. Press and release the MODE
button until the compass directional
heading is displayed.

53

Driver Controls

2. Hold down the MODE button for
5 seconds to enter zone mode. The
display will read PRESS RESET TO
SET ZONE XX where XX is the
current zone.

3. Release the MODE button.

4. Repeatedly press and release the
RESET button to scroll through the
zones 1–15 until the desired zone is
displayed.

5. Press the MODE button to save

4

the new zone setting and return to
the compass normal mode.

5

Note: The compass exits the zone
setting mode and returns to its
previous setting after one minute of
no activity.

Note: If power is interrupted during the zone setting process, the
compass resets to the same zone it was set to before the zone change
process was started.

Calibration mode

To calibrate the compass:

1. Press and release the MODE
button until the compass directional
heading is displayed.

123

6 7 8 91011

15
14

13
12

2. Hold down the MODE button for
10 seconds to enter the calibration
mode. The display will read PRESS
RESET TO DECAL.

3. Release the MODE button.

54

Driver Controls

4. Press the RESET button to
de-calibrate the compass. The
display will read CIRCLE SLOWLY
TO CALIBRATE for a few seconds
and then display a direction with
CAL displayed on the right side.

5. Slowly drive the vehicle in a
circle (less than 5 km/h [3 mph]).
This will take up to three circles to complete calibration.

6. The correct compass heading will be displayed when the compass is
calibrated.

Note: If the RESET button is not pressed, the compass will exit
calibration mode after three minutes of no activity and the original
calibration data will be restored.

Note: If power is interrupted during the calibration process, the compass
resets to the original calibration data from before the calibration process
started.

HomeLinkTmode
Train mode

Note: Do not train the HomeLinkt with the vehicle parked in the garage.
To train a HomeLinkt button to control a specific device:

1. Select the HomeLinkt button to
train.

2. Press and continuously hold the
button for 20 seconds. CHANNEL X
TRANSMIT will be displayed (X will
be 1, 2, or 3) during this time.

Note: If more than one button is
pressed, priority will be given to the
lowest numbered channel.

55

Driver Controls

3. After 20 seconds, the display will
read CHANNEL X TRANING to
indicate training has started.
Continue to hold the button.

Note: If the channel being trained
has not been previously trained, the
channel will immediately enter the
training mode (no 20 second delay).

4. Point the original garage door
opener/transmitter at the overhead
console. Hold down the original transmitter’s button so the overhead
console can learn the transmitter’s frequency and data stream.

5. Training will be complete in 100
seconds or less. CHANNEL X
TRAINED will be displayed when
training is complete.

6. DID NOT TRAIN will be displayed
if the channel did not properly train.

7. Release the channel X button.
Training is complete.

Note: Additional training may be
required for rolling code equipped
devices. Refer to the Rolling code
programming in this section.

Rolling code programming

To train a garage door opener (or other rolling code equipped devices)
with the rolling code feature, follow these instructions after completing
the “Train mode” in this section. (A second person may make the
following training procedures quicker & easier)

1. Locate the “learn” or “smart” button on the garage door motor
head unit. Exact location and color of the button may vary by product

56

Driver Controls

brand. If there is difficulty locating the “learn” or “smart” button refer to
the device’s owner manual or contact HomeLinkt at 1–800–355–3515 or
on the Internet at www.homelink.com.

2. Press and release the “learn” or “smart” button on the garage door
motor head unit.

Note: Following step 2, there are 30 seconds in which to initiate step 3.

3. Press and release the
programmed HomeLinkt button.
Press and release the HomeLinkt
button a second time to complete
the training process. (Some garage
door openers may require this
procedure to be done a third time
to complete the training.)

The rolling code equipped device
should now recognize the
HomeLinkt signal and activate when
the HomeLink button is pressed. The remaining two buttons may now be
programmed if this has not previously been done. Refer to the “Train
mode” in this section.

Transmit mode

1. Select the button for the desired
channel (for example, for the garage
door you wish to open).

2. Press the button. CHANNEL X
TRANSMIT is displayed.

3. The proper signal is transmitted
to the device being controlled.

4. Release the button.
Note: If more than one button is

pressed, priority will be given to the
lowest numbered channel.

57

Driver Controls

Erase mode

To erase all three HomeLinkt channel codes:

1. Simultaneously press and hold
buttons 1 and 3 for 20 seconds.

2. CLEARING CHANNELS will be
displayed when the channel codes
are being erased.

3. CHANNELS CLEARED will be
displayed when the erase operation
is complete.

4. Release buttons 1 and 3.

HomeLinkTdefault code mode

HomeLinkt uses default codes for testing and for optional home lighting
accessories. To load the default codes:

1. Simultaneously press and hold
buttons 1 and 3. CLEARING
CHANNELS is displayed.

58

Driver Controls

2. After 20 seconds CHANNELS
CLEARED is displayed. Continue to
hold the buttons.

3. After 10 more seconds,
CHANNELS DEFAULTED is
displayed when all the channel
default codes have been successfully
loaded.

Note: If you need to train the
garage door opener, refer to “Train
mode” in this section.

AUXILIARY POWER POINT

The auxiliary power point is located in the floor console storage bin.
Do not plug optional electrical accessories into the cigarette lighter. Use

the power point.
Do not use the power point for operating the cigarette lighter element.
The Maximum power each power point can supply depends on the fuse

rating. For example: a 20A fuse should supply a maximum of 240 Watts,
a 15A fuse should supply a maximum of 180 Watts and a 10A fuse should
supply a maximum of 120 Watts. Exceeding these limits will result in a
blown fuse.

59

Driver Controls

Always keep the power point caps closed when not being used.

Power outlets are designed for accessory plugs only. Do not hang
any type of accessory or accessory bracket from the plug.
Improper use of the power outlet can cause damage not covered
by your warranty.

POWER WINDOWS

Press and hold the rocker switches to open and close windows.

• Press the top portion of the
rocker switch to close.

• Press the bottom portion of the
rocker switch to open.

60

One touch down

• Press the bottom portion of the
rocker switch completely down
and release quickly. The driver’s
window will open fully. Depress
again to stop window operation.

One touch down can be deactivated
during operation by pushing down
on the top part of the driver power
window control.

Window lock

The window lock feature allows only
the driver to operate the power
windows.

To lock out all the window controls
except for the driver’s press the left
side of the control. Press the right
side to restore the window controls.

POWER SIDE VIEW MIRRORS

To adjust your mirrors:

1. Select

mirror or
mirror.

2. Move the control in the direction

you wish to tilt the mirror.

3. Return to the center position to

lock mirrors in place.

to adjust the left

to adjust the right

Driver Controls

61

Driver Controls

Heated outside mirrors

Both mirrors are heated
automatically to remove ice, mist
and fog when the rear window
defrost is activated.

Do not remove ice from the
mirrors with a scraper or
attempt to readjust the mirror
glass if it is frozen in place.
These actions could cause damage to the glass and mirrors.

Fold-away mirrors

Pull the side mirrors in carefully
when driving through a narrow
space, like an automatic car wash.

Automatic dimming inside rear view mirror

Your vehicle is equipped with an
inside rear view mirror which has an
auto-dimming function. The
electronic day/night mirror will
change from the normal state to the
non-glare state when bright lights
(glare) reach the mirror. When the mirror detects bright light from front
or behind, it will automatically adjust (darken) to minimize glare.

Do not block the sensor on the backside of the mirror since this may
impair proper mirror performance.

Press the control to turn the mirror OFF or AUTO.
The mirror will automatically return to the normal state whenever the

vehicle is placed in R (Reverse)(when the mirror is on) to ensure a
bright clear view when backing up.

OFF AUTO

62

Driver Controls

POWER ADJUSTABLE FOOT PEDALS

The accelerator and brake pedal
should only be adjusted when the
vehicle is stopped and the gearshift
lever is in the P(Park) position.

Press and hold the rocker control to
adjust accelerator and brake pedal.

• Press the left side of the control to adjust the pedals toward you.

• Press the right side of the control to adjust the pedals away from you.

The adjustment allows for approximately 65 mm (2.5 inches) of
maximum travel.

Never adjust the accelerator and brake pedal with feet on the
pedals while the vehicle is moving.

SPEED CONTROL
To turn speed control on

• Press ON.

Vehicle speed cannot be controlled
until the vehicle is traveling at or
above 48 km/h (30 mph).

Do not shift the gearshift lever
into N (Neutral) with the speed
control on.

Do not use the speed control in heavy traffic or on roads that
are winding, slippery, or unpaved.

63

Driver Controls

To turn speed control off

• Press OFF or

• Turn off the vehicle ignition.

Once speed control is switched off,
the previously programmed set
speed will be erased.

To set a speed

• Press SET ACCEL. For speed
control to operate, the speed
control must be ON and the
vehicle speed must be greater
than 48 km/h (30 mph).

If you drive up or down a steep hill, your vehicle speed may vary
momentarily slower or faster than the set speed. This is normal.

Speed control cannot reduce the vehicle speed if it increases above the
set speed on a downhill. If your vehicle speed is faster than the set
speed while driving on a downhill, you may want to shift to the next
lower gear or apply the brakes to reduce your vehicle speed.

If your vehicle slows down more than 16 km/h (10 mph) below your set
speed on an uphill, your speed control will disengage. This is normal.
Pressing RESUME will re-engage it.

Do not use the speed control in heavy traffic or on roads that
are winding, slippery, or unpaved.

64

Driver Controls

To set a higher set speed

• Press and hold SET ACCEL.
Release the control when the
desired vehicle speed is reached
or

• Press and release SET ACCEL to
operate the Tap-Up function.
Each press will increase the set
speed by 1.6 km/h (1 mph) or

• Accelerate with your accelerator pedal. When the desired vehicle
speed is reached, press and release SET ACCEL.

You can accelerate with the accelerator pedal at any time during speed
control usage. Releasing the accelerator pedal will return your vehicle to
the previously programmed set speed.

To set a lower set speed

• Press and hold COAST. Release
the control when the desired
speed is reached or

• Press and release COAST to
operate the Tap-Down function.
Each press will decrease the set
speed by 1.6 km/h (1 mph) or

• Depress the brake pedal. When
the desired vehicle speed is
reached, press SET ACCEL.

65

Driver Controls

To disengage speed control

• Depress the brake pedal.

Disengaging the speed control will
not erase the previously
programmed set speed.

Pressing OFF will erase the
previously programmed set speed.

To return to a previously set speed

• Press RESUME. For RESUME to
operate, the vehicle speed must
be faster than 48 km/h (30 mph).

66

STEERING WHEEL CONTROLS
Radio control features

• Press BAND/MODE to select AM,
FM1, FM2, TAPE or CD (if
equipped).

In Radio mode:

• Press MEM/NEXT to select a
preset station from memory.

In Tape mode:

• Press MEM/NEXT to listen to the
next selection on the tape.

In CD mode:

• Press MEM/NEXT to listen to the
next track on the disc.

In any mode:

• Press VOL up or down to adjust the volume.

Climate control features

• Press TEMP up or down to adjust temperature.

• Press FAN up or down to adjust fan speed.

MOON ROOF (IF EQUIPPED)

To open the moon roof:

• Press and hold the control
forward to raise the moon roof to
the vent position (when the glass
panel is closed).

• For one-touch operation, press
and release the rear portion of
the control; this will fully open
the moon roof.

• To stop one-touch operation at
the desired position, press and
release the forward portion of the control.

To close the moon roof:

• Press and hold the front portion of the control.

Driver Controls

NEXT

MODE

67

Driver Controls

• To close from the vent position, press and hold the rear portion of the
control.

Do not let children play with the moon roof. They may seriously
hurt themselves.

HOMELINKT UNIVERSAL TRANSCEIVER

The HomeLinkt Universal Transceiver, located on the driver’s visor,
provides a convenient way to replace up to three hand-held transmitters
with a single built-in device. This feature will learn the radio frequency
codes of most current transmitters to operate garage doors, entry gate
operators, security systems, entry door locks, and home or office lighting.

When programming your HomeLinkt Universal Transceiver to a
garage door or gate, be sure that people and objects are out of

the way to prevent potential harm or damage.

Do not use the HomeLinkt Universal Transceiver with any garage door
opener that lacks safety stop and reverse features as required by U.S.
federal safety standards (this includes any garage door opener model
manufactured before April 1, 1982). A garage door which cannot detect
an object, signaling the door to stop and reverse, does not meet current
U.S. federal safety standards. For more information, contact HomeLinkt
at: www.homelink.com or 1–800–355–3515.

Retain the original transmitter for use in other vehicles as well as for
future programming procedures (i.e. new HomeLinkt equipped vehicle
purchase). It is also suggested that upon the sale of the vehicle, the
programmed Homelinkt Universal Transceiver buttons be erased for
security purposes, refer to Programming in this section.

Programming

Do not program the HomeLinkt Universal Transceiver with the
vehicle parked in the garage.

Note: Some vehicles may require the ignition switch to be turned to the

second (or “ACC”) position for programming and/or operation of the
HomeLinkt. It is also recommended that a new battery be placed in the
hand-held transmitter of the device being programmed to HomeLinkt for
quicker training and accurate transmission of the radio-frequency signal.

68

Driver Controls

1. Press and hold the two outside

buttons releasing only when the red
light begins to flash after 20
seconds. Do not repeat step one to
program additional hand-held
transmitters to the remaining two
HomeLinkt buttons. This will erase
previously programmed hand-held
transmitter signals into HomeLinkt.

2. Position the end of your

hand-held transmitter 2–8 cm (1–3
inches) away from the HomeLinkt Universal Transceiver surface (located
on your overhead console) while keeping the red light in view.

3. Simultaneously press and hold

both the HomeLinkt and hand-held
transmitter button. Do not release

the buttons until step 4 has been
completed.

Some entry gates and garage door
openers may require you to replace
step 3 with procedures noted in the
“Gate Operator and Canadian
Programming” section for Canadian
residents.

4. The red light will flash slowly and then rapidly. Release both buttons

when the red light flashes rapidly. (The rapid flashing light indicates
acceptance of the hand-held transmitters’ radio frequency signals.)

5. Press and hold the just-trained HomeLinkt button and observe the red

light. If the light is a constant red, programming is complete and your
device should activate when the HomeLinkt button is pressed and
released. Note: To program the remaining two HomeLinkt buttons,
begin with step 2 in the “Programming” section — do not repeat step 1.
If the red light blinks rapidly for two seconds and then turns to a
continuous red, proceed with steps 6 through 8 to complete
programming of a rolling code equipped device.

6. At the garage door opener receiver (motor-head unit) in the garage,

locate the “learn” or “smart” button (usually near where the hanging
antenna wire is attached to the unit).

7. Press and release the “learn” or “smart” button. (The name and color

of the button may vary by manufacturer.)

69

Driver Controls

Note: There are 30 seconds in which to initiate step eight.

8. Return to the vehicle and firmly press, hold for two seconds and

release the HomeLinkt button. Repeat the press/hold/release sequence
again, and, depending on the brand of the garage door opener (or other
rolling code equipped device), repeat this sequence a third time to
complete the programming.

HomeLinkt should now activate your rolling code equipped device. To
program additional HomeLinkt buttons begin with step 2 in the
“Programming” section. For questions or comments, please contact
HomeLink at www.homelink.com or 1–800–355–3515.

Operating the HomeLinkT Universal Transceiver

To operate, simply press and release
the appropriate HomeLinkt button.
Activation will now occur for the
trained product (garage door, gate
operator, security system, entry
door lock, or home or office lighting
etc.). For convenience, the
hand-held transmitter of the device
may also be used at any time. In the
event that there are still
programming difficulties, contact
Homelinkt at www.homelink.com or 1–800–355–3515.

Erasing HomeLinkT buttons

To erase the three programmed
buttons (individual buttons cannot
be erased):

• Press and hold the two outer
HomeLinkt buttons until the red
indicator light begins to
flash-after 20 seconds. Release
both buttons. Do not hold for
longer that 30 seconds.

HomeLinkt is now in the train (or
learning) mode and can be programmed at any time beginning with step
2inthe“Programming” section.

Reprogramming a single HomeLinkTbutton

To program a device to HomeLinkt using a HomeLinkt button previously
trained, follow these steps:

70

Driver Controls

1. Press and hold the desired HomeLinkt button. Do NOT release the

button.

2. The red indicator light will begin to flash after 20 seconds. Without

releasing the HomeLinkt button, follow step 2 in the “Programming”
section.

For questions or comments, contact HomeLinkt at www.homelink.com
or 1–800–355–3515.

Gate Operator & Canadian Programming

During programming, your
hand-held transmitter may
automatically stop transmitting —
not allowing enough time for
HomeLinkt to accept the signal
from the hand-held transmitter.

After completing steps 1 and 2
outlined in the “Programming”
section, replace step 3 with the
following:

Note: If programming a garage door opener or gate operator, it is
advised to unplug the device during the “cycling” process to prevent
overheating.

• Continue to press and hold the HomeLinkt button (note step 3 in the
“Programming” section) while you press and release — every two
seconds (“cycle”) your hand-held transmitter until the frequency
signal has been accepted by the HomeLinkt. The red indicator light
will flash slowly and then rapidly after HomeLinkt accepts the radio
frequency signal.

• Proceed with step 4 in the “Programming” section.

OVERDRIVE CONTROL
Activating overdrive

(Overdrive) is the normal drive position for the best fuel economy.

The overdrive function allows automatic upshifts and downshifts through
all available gears.

71

Driver Controls

Deactivating overdrive

Overdrive can be deactivated by
pressing the Transmission Control
Switch (TCS) on the gearshift
handle.

The Transmission Control Indicator

O/D

Light
instrument cluster. The transmission
will operate in all gears except
overdrive.

To return to normal overdrive mode,
press the Transmission Control Switch again. The
illuminated.

When you shut off and re-start your vehicle, the transmission will
automatically return to normal

For additional information about the gearshift lever and the transmission
control switch operation refer to the Automatic Transmission
Operation section of the Driving chapter.

FUEL DOOR RELEASE

Your vehicle is equipped with a
locking fuel door. To open the door,
press the control located on the
door.

will illuminate on the

OFF

O/D

OFF

(Overdrive) mode.

will no longer be

72

Fuel filler door override release

If the remote release is inoperative,
open the trunk, then pull the
override release handle located
inside the trunk to open the fuel
filler door.

INTERIOR TRUNK CONTROL

The remote trunk release control is
located on the driver’s door trim
panel and can be operated at any
time.

You can render the switch
inoperable by locking the button
with your master key.

Driver Controls

CELL PHONE USE

The use of Mobile Communications Equipment has become increasingly
important in the conduct of business and personal affairs. However,
drivers must not compromise their own or others’ safety when using
such equipment. Mobile Communications can enhance personal safety
and security when appropriately used, particularly in emergency
situations. Safety must be paramount when using mobile communications
equipment to avoid negating these benefits.

Mobile Communication Equipment includes, but is not limited to cellular
phones, pagers, portable email devices, in vehicle communications
systems, telematics devices and portable two-way radios.

73

Driver Controls

A driver’s first responsibility is the safe operation of the vehicle.

The most important thing you can do to prevent a crash is to
avoid distractions and pay attention to the road. Wait until it is safe to
operate Mobile Communications Equipment.

CENTER CONSOLE

Your vehicle may be equipped with a variety of console features. These
include:

• Utility compartment

• Power point (inside utility compartment storage bin)

• Cupholders

• Air vents to the rear seating positions (heat only)

• Coin holders (inside utility compartment storage bin)

• Ash tray cup (insert in left cup holder only)

POSITIVE RETENTION FLOOR MAT

Position the driver floor mat so that
the eyelet is over the pointed end of
the retention post and rotate
forward to lock in. Make sure that
the mat does not interfere with the
operation of the accelerator or the
brake pedal. To remove the floor
mat, reverse the installation
procedure.

74

Locks and Security

KEYS

The key operates all locks on your vehicle. In case of loss, replacement
keys are available from your dealer.

You should always carry a second key with you in a safe place in case
you require it in an emergency.

Refer to SecuriLocky Passive Anti-Theft System for more information.

POWER DOOR LOCKS

Press control to unlock all doors.
Note: When Perimeter Alarm is
armed, this switch is disabled.

Press control to lock all doors.

Smart locks

With the key in any ignition position, and either the driver’s or
passenger’s door open, the doors cannot be locked using the power door
lock switches.

The vehicle may still be locked with the key in the ignition, and
performing one of the following actions:

• Pressing the manual lock button on the door.

• Operating the remote entry transmitter.

• Operating the keyless entry keypad.

• Operating the driver’s door with a key.

75

Locks and Security

Childproof door locks

• When these locks are set, the
rear doors cannot be opened from
the inside.

• The rear doors can be opened
from the outside when the doors
are unlocked.

The childproof locks are located on
rear edge of each rear door and
must be set separately for each door. Setting the lock for one door will
not automatically set the lock for both doors.

• Move lock control up to engage the childproof lock.

• Move control down to disengage childproof locks.

INTERIOR LUGGAGE COMPARTMENT RELEASE

Your vehicle is equipped with a mechanical interior luggage compartment
release handle that provides a means of escape for children and adults in
the event they become locked inside the luggage compartment.

Adults are advised to familiarize themselves with the operation and
location of the release handle.

To open the luggage compartment
door (lid) from within the luggage
compartment, pull the illuminated
“T” shaped handle and push up on
the trunk lid. The handle is
composed of a material that will
glow for hours in darkness following
brief exposure to ambient light.

The “T” shaped handle will be
located either on the luggage
compartment door (lid) or inside
the luggage compartment near the
tail lamps.

76

Locks and Security

Keep vehicle doors and

luggage compartment
locked and keep keys and remote
transmitters out of a child’s reach.
Unsupervised children could lock
themselves in the trunk and risk
injury. Children should be taught
not to play in vehicles.

On hot days, the temperature in the trunk or vehicle interior can

rise very quickly. Exposure of people or animals to these high
temperatures for even a short time can cause death or serious
heat-related injuries, including brain damage. Small children are
particularly at risk.

REMOTE ENTRY SYSTEM

This device complies with part 15 of the FCC rules and with RS-210 of
Industry Canada. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) This device
must accept any interference received, including interference that may
cause undesired operation.

Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to
operate the equipment.

The remote entry system allows you to lock or unlock all vehicle doors
without a key.

The remote entry features operate in any ignition position except when
the vehicle is running and the transmission is not in P (park) or N
(Neutral).

If there is any potential remote keyless entry problem with your vehicle,
ensure ALL remote entry transmitters are brought to the dealership,
to aid in troubleshooting.

77

Locks and Security

Unlocking the doors

Press this control to unlock the
driver’s door. The interior lamps will
illuminate.

Press the control a second time
within five seconds to unlock all
doors.

Locking the doors

Press this control to lock all doors.
The horn will chirp and the

parklamps/taillamps will flash to
confirm the control was pressed.

Deactivating/activating the horn chirp and flash confirmation
feature

The horn chirp and flash confirmation feature can be turned on/off
through the following procedure using the power door locks:

You must complete steps 1-7 within 30 seconds or the procedure will
have to be repeated. If the procedure needs to be repeated, you must
wait 30 seconds.

1. Turn the ignition key to ON.

2. Press the power door unlock control on the door panel three times.

3. Turn the ignition key from ON to OFF.

4. Press the power door unlock control three times.

5. Turn the ignition back to ON. The door locks will cycle lock/unlock.

6. Press the unlock control twice.

78

Locks and Security

7. After a five to ten second delay, the door locks will cycle lock/unlock
to confirm successful programming.

8. Turn the ignition to OFF.

Sounding a panic alarm

Press this control to activate the
alarm.

To deactivate the alarm, press the
control again or turn the ignition to
ACC or ON.

Panic alarm will only operate with
the ignition in the OFF position.

Opening the trunk

Press the control once to open the
trunk.

Ensure that the trunk is closed and
latched before driving your vehicle.
Failure to latch the trunk may cause
objects to fall out of the trunk or
block the rear view. This feature will
not work with the transmission out
of P (Park) or N (Neutral) if the
ignition is in either the ACC or ON
position.

Replacing the battery

The remote transmitter is powered by one coin type three-volt lithium
battery CR2032 or equivalent. Typical operating range will allow you to
be up to 10 meters (33 feet) away from your vehicle. A decrease in
operating range can be caused by the following factors:

• Weather conditions

• Nearby radio towers

• Structures around the vehicle

• Other vehicles parked next to the vehicle

79

Locks and Security

To replace the battery:

1. Twist a thin coin between the two
halves of the transmitter near the
key ring. DO NOT TAKE THE
FRONT PART OF THE
TRANSMITTER APART.

2. Place the positive (+) side of new
battery in the same orientation.
Refer to the diagram inside the
transmitter unit.

3. Snap the two halves back
together.

Replacement of the battery will not cause the remote transmitter to
become deprogrammed from your vehicle. The remote transmitter should
operate normally after battery replacement.

Replacing lost transmitters

Take all your vehicle’s transmitters
to your dealer if service is required.

If a remote transmitter has been lost
and you would like to remove it
from the vehicle’s memory, or you
would like to purchase additional
remote transmitters and have them
programmed to your vehicle:

• Take all your vehicle’s
transmitters to your dealer for
programming, or

• Perform the following programming procedure yourself.

Place the key in the ignition and
turn from 2 (LOCK) to 3 (OFF) and
cycle between 3 (OFF) and 4 (ON)
four times in rapid succession within
3 seconds. After doors lock/unlock,
press any control on all transmitters
(up to four). When completed, turn
the ignition to 3 (OFF).

All transmitters must be
programmed at the same time.

3

2

1

4

5

80

Locks and Security

Illuminated entry

The interior lamps illuminate:

• when the remote entry system is used to unlock the door(s) or sound
the panic alarm, or

• when the driver door is unlocked using the key in the driver door key
cylinder.

The system automatically turns off after 25 seconds after the UNLOCK
button on the RUN or ACC position.

The inside lights will not turn off if:

• they have been turned on with the dimmer control, or

• any door is open.

The battery saver will shut off the interior lamps 10 minutes after the
ignition is turned off. Demand lighting will turn off after 30 minutes.

Autolock

This feature automatically locks all vehicle doors when:

• all doors are closed,

• the ignition is in the ON position,

• the brake pedal is depressed and

• you shift into any gear.

Relock

The autolock feature repeats when:

• the ignition is in the ON position,

• a door is open and then closed,

• the transmission is placed in Reverse or any Drive gear, and then

• the brake pedal is depressed and then released.

Deactivating/activating the autolock feature

Before following the procedure, make sure that the ignition is OFF and
all vehicle doors are closed.

Automatic door locks can be turned on/off with the keyless entry keypad
through the following procedure:

You must complete steps 1-5 within 30 seconds or the procedure will
have to be repeated. If the procedure needs to be repeated, you must
wait 30 seconds.

81

Locks and Security

1. Enter the keyless entry keypad factory code.

2. Within 5 seconds, press and hold control 7/8.

3. Within 5 seconds (while holding down control 7/8), press and release

control 3/4.

4. Release control 7/8.

The door will lock/unlock to confirm the feature has been disabled. Once
disabled, the feature can be enabled by repeating the same sequence.

Automatic door locks can also be turned on/off through the following
procedure:

You must complete steps 1-7 within 30 seconds or the procedure will
have to be repeated. If the procedure needs to be repeated, you must
wait 30 seconds.

1. Turn the ignition key to ON.

2. Press the power door unlock control on the door panel three times.

3. Turn the ignition key from ON to OFF.

4. Press the power door unlock control three times.

5. Turn the ignition back to ON.

6. Press the unlock control once. After a five to ten second delay, the

door will lock/unlock to confirm successful programming.

7. Turn the ignition to OFF.

KEYLESS ENTRY SYSTEM

With the keyless entry keypad, you
can:

• lock or unlock the vehicle doors
without using the key.

• open the trunk.

• disable/enable autolock.

See also Remote entry system in this chapter for more information.
Your vehicle has a factory-set 5–digit code that operates the keyless

entry system. You can also program your own 5–digit personal entry
code.

The factory-set code is located:

• On the owner’s wallet card in the glove compartment,

• Taped to the computer module, or

1 2

3

4567890

82

Locks and Security

• At your dealer.

When using the keyless entry keypad, press the middle of each button in
order to ensure a good activation.

Programming your own entry code

1. Enter the factory-set code (keypad will illuminate when pressed).

2. Press the 1/2 control within five

seconds of step 1.

3. Enter your personal 5 digit code.

Enter each digit within five seconds
of the previous one.

All of the vehicle doors will lock and unlock to confirm programming of
the new code.

Do not set a code that includes five of the same number or presents
them in sequential order; these types of codes are easier to figure out.

You can program up to three personal codes to unlock your vehicle.
These codes do not replace the permanent code that the dealership gave
you.

Erasing personal code

To erase all of the personal entry codes programmed to a vehicle:

1. Enter the factory-set code.

2. Press and release 1/2 within 5

seconds of step 1.

3. Press and hold 1/2 for two

seconds. All of the vehicle doors will
lock and then unlock to confirm
erasure.

1 2

1 2

3

4567890

3

4567890

Unlocking the doors and releasing the trunk with the keyless entry
system

To unlock the driver door, enter either the factory-set code or personal
code (each digit pressed within 5 seconds of prior digit). The interior
lamps will illuminate.

83

Locks and Security

To unlock all doors, enter the
factory-set code or personal code
(driver door unlocks) and press 3/4
within five seconds.

To release the trunk, enter the
factory-set code or personal code
(driver door unlocks) and press 5/6
within five seconds.

After the factory-set code or personal code has been entered, you can
unlock all doors (press 3/4) and release the trunk (press 5/6) as long as
the controls are pressed within 5 seconds of each other.

Locking doors with the keyless entry system

It is not necessary to enter the factory-set code prior to locking all doors.
To lock the doors:

Press 7/8 and 9/0 at the same time.

1 2

1 2

1 2

3

4567890

3

4567890

3

4567890

SECURILOCKY PASSIVE ANTI-THEFT SYSTEM

SecuriLocky passive anti-theft system is an engine immobilization
system. This system is designed to prevent the engine from being started
unless a coded key programmed to your vehicle is used.

The SecuriLocky passive anti-theft system is not compatible with
non-Ford aftermarket remote start systems. Use of these systems may
result in vehicle starting problems and a loss of security protection.

THEFT INDICATOR

The theft indicator is the flashing red indicator located on the dash
panel.

84

Locks and Security

• When the ignition is in the OFF position, the indicator will flash once
every 2 seconds to indicate the SecuriLocky system is functioning as
a theft deterrent.

• When the ignition is in the ON position, the indicator will glow for 3
seconds to indicate normal system functionality.

If a problem occurs with the SecuriLocky system, the indicator will flash
rapidly or glow steadily when the ignition is in the ON position. If this
occurs, the vehicle should be taken to an authorized dealer for service.

Automatic arming

The vehicle is armed immediately
after switching the ignition to the 3
(OFF) or 2 (LOCK) position. The
indicator on the instrument panel
will flash every two seconds when
the vehicle is armed.

Automatic disarming

Switching the ignition to the 4 (ON) position with a coded key disarms
the vehicle. The indicator on the instrument will illuminate for three
seconds and then go out. If the indicator stays on for an extended period
of time or flashes rapidly, have the system serviced by your dealership or
a qualified technician.

3

2

1

4

5

Key information

Your vehicle is supplied with two coded keys (or three, if your vehicle
is equipped with the valet feature). Only a coded key will start your
vehicle. Spare coded keys can be purchased from your dealership. Your
dealership can program your key or you can “do it yourself.” Refer to

Programming spare keys.

The following items may prevent the vehicle from starting:

• Large metallic objects

• Electronic devices on the key chain that can be used to purchase

gasoline or similar items

• A second key on the same key ring as the coded key

85

Locks and Security

If any of these items are present, you need to keep these objects from
touching the coded key while starting the engine. These objects and
devices cannot damage the coded key, but can cause a momentary “no
start” condition if they are too close to the key during engine start. If a
problem occurs, turn ignition OFF and restart the engine with all other
objects on the key ring held away from the ignition key. Check to make
sure the coded key is an approved Ford coded key.

If your keys are lost or stolen you will need to do the following:

• Use your spare key to start the vehicle, or

• Have your vehicle towed to a dealership or a locksmith. The key codes

will need to be erased from your vehicle and new key codes will need
to be re-coded.

Replacing coded keys can be very costly and you may want to store an
extra programmed key away from the vehicle in a safe place to prevent
an unforeseen inconvenience.

The correct coded key must be used for your vehicle. The use of the
wrong type of coded key may lead to a “no start” condition.

If an unprogrammed key is used in the ignition it will cause a “no
start” condition.

Programming spare keys

A maximum of eight keys can be coded to your vehicle. Only
SecuriLocky keys can be used. To program a coded key yourself, you
will need two previously programmed coded keys (keys that already
operate your vehicle’s engine) and the new unprogrammed key(s) readily
accessible for timely implementation of each step in the procedure.

If two previously programmed coded keys are not available, you must
bring your vehicle to your dealership to have the spare coded key(s)
programmed.

Please read and understand the entire procedure before you begin.

86

Locks and Security

1. Insert the first previously

programmed coded key into the
ignition and turn the ignition from 3
(OFF) to 4 (ON) (maintain ignition
in 4 (ON) for at least one second).

2. Turn ignition to 3 (OFF) then 2

(LOCK) and remove the first coded
key from the ignition.

3. Within ten seconds of removing

the first coded key, insert the
second previously programmed coded key into the ignition and turn the
ignition from 3 (OFF) to 4 (ON) (maintain ignition in 4 (ON) for at least
one second but no more than ten seconds).

4. Turn the ignition to 3 (OFF) then 2 (LOCK) and remove the second

coded key from the ignition.

5. Within twenty seconds of removing the second coded key, insert the

new unprogrammed key (new key) into the ignition and turn the ignition
from 3 (OFF) to 4 (ON) (maintain ignition in 4 (ON) for at least one
second). This step will program your new key to a coded key.

6. To program additional new unprogrammed key(s), repeat this

procedure from step 1.
If successful, the new coded key(s) will start the vehicle’s engine and the

theft indicator will illuminate for three seconds and then go out.
If not successful, the new coded key(s) will not start the vehicle’s engine

and the theft indicator will flash on and off and you may repeat steps 1
through 6. If failure repeats, bring your vehicle to your dealership to
have the new spare key(s) programmed.

3

2

1

4

5

87

Seating and Safety Restraints

SEATING
Adjustable head restraints

Your vehicle’s seats are equipped with head restraints which are
vertically adjustable. The purpose of these head restraints is to help limit
head motion in the event of a rear collision. To properly adjust your head
restraints, lift the head restraint so that it is located directly behind your
head or as close to that position as possible. Refer to the following to
raise and lower the head restraints.

The head restraints can be moved
up and down.

Push control to lower head restraint.

Using the power lumbar support

The power lumbar control is located
on the front inboard side of the
seat.

Press one side of the control to
adjust firmness.

Press the other side of the control
to adjust softness.

88

Seating and Safety Restraints

Heated seats (if equipped)

To operate the heated seats:

• Push the indicated side of the
control for maximum heat.

• Push again to deactivate.

• Push the indicated side of the

control for minimum heat.

• Push again to deactivate.

The heated seat module resets at every ignition run cycle. While the
ignition is in the run position, activating the high or low heated seat
switch enables heating mode. When activated, they will turn off
automatically when the ignition is turned to the OFF position.

The indicator light will illuminate when the heated seats have been
activated.

Adjusting the power front seats – door mounted controls

The controls for the power seats are located on the inside of each front
door.

Never adjust the driver’s seat or seatback when the vehicle is
moving.

Do not pile cargo higher than the seatbacks to avoid injuring
people in a collision or sudden stop.

Always drive and ride with your seatback upright and the lap
belt snug and low across the hips.

89

Seating and Safety Restraints

Reclining the seatback can cause an occupant to slide under the
seat’s safety belt, resulting in severe personal injuries in the

event of a collision.

Press the control to recline the
seatback forward or backward.

Press to move the seat forward or
backward.

Press to move the front portion of
the seat cushion up or down.

90

Seating and Safety Restraints

Press to move the rear portion of
the seat cushion up or down.

SAFETY RESTRAINTS
Personal Safety System

The Personal Safety System provides an improved overall level of frontal
crash protection to front seat occupants and is designed to help further
reduce the risk of air bag-related injuries. The system is able to analyze
different occupant conditions and crash severity before activating the
appropriate safety devices to help better protect a range of occupants in
a variety of frontal crash situations.

Your vehicle’s Personal Safety System consists of the following items:

• Driver and passenger dual-stage air bag supplemental restraints

• Driver and front passenger side air bags

• Front safety belts with pretensioners, energy management retractors,

and safety belt usage sensors

• Driver’s seat position sensor

• Passenger occupant classification sensor

• Front crash severity sensor

• Restraints Control Module (RCM) with impact and safing sensors

• Restraint system warning light and back-up tone

• The electrical wiring for the air bags, crash sensor(s), safety belt

pretensioners, front safety belt usage sensors, driver seat position
sensor, passenger occupant classification sensor, and indicator lights

How does the personal safety system work?

The Personal safety system can adapt the deployment strategy of your
vehicle’s safety devices according to crash severity and occupant
conditions. A collection of crash and occupant sensors provides

91

Seating and Safety Restraints

information to the Restraints control module (RCM). During a crash, the
RCM activates the safety belt pretensioners and/or either one or both
stages of the dual-stage air bag supplemental restraints based on crash
severity and occupant conditions.

The fact that the pretensioners or air bags did not activate for both front
seat occupants in a collision does not mean that something is wrong with
the system. Rather, it means the Personal safety system determined the
accident conditions (crash severity, belt usage, etc.) were not
appropriate to activate these safety devices. Front air bags and
pretensioners are designed to activate only in frontal and near-frontal
collisions, not rollovers, side-impacts, or rear-impacts unless the collision
causes sufficient longitudinal deceleration.

Driver and passenger dual-stage air bag supplemental restraints

The dual-stage air bags offer the capability to tailor the level of air bag
inflation energy. A lower, less forceful energy level is provided for more
common, moderate-severity impacts. A higher energy level is used for
the most severe impacts. Refer to Air bag supplemental restraints
section in this chapter.

Front crash severity sensor

The front crash severity sensor enhances the ability to detect the
severity of an impact. Positioned up front, it provides valuable
information early in the crash event on the severity of the impact. This
allows your Personal safety system to distinguish between different levels
of crash severity and modify the deployment strategy of the dual-stage
air bags and safety belt pretensioners.

Driver’s seat position sensor

The driver’s seat position sensor allows your Personal safety system to
tailor the deployment level of the driver dual-stage air bag based on seat
position. The system is designed to help protect smaller drivers sitting
close to the driver air bag by providing a lower air bag output level.

Passenger occupant classification sensor (OCS)

For air bags to do their job they must inflate with great force, and this
force can pose a potentially deadly risk to occupants that are very close
to the air bag when it begins to inflate. For some occupants, this occurs
because they are initially sitting very close to the air bag. For other
occupants, this occurs when the occupant is not properly restrained by
seat belts or child safety seats and they move forward during pre-crash
braking. The most effective way to reduce the risk of unnecessary

92

Seating and Safety Restraints

injuries is to make sure all occupants are properly restrained. Accident
statistics suggest that children are much safer when properly restrained
in the rear seating positions than in the front.

Air bags can kill or injure a child in a child seat. NEVER place a

rear-facing child seat in front of an active air bag. If you must
use a forward-facing child seat in the front seat, move the seat all the
way back.

Always transport children 12 years old and under in the back

seat and always properly use appropriate child restraints.

The passenger occupant classification sensor can automatically turn off
the passenger front air bag and side air bag (if equipped). The system is
designed to help protect small (child size) occupants from air bag
deployments when they are improperly seated or restrained in the front
passenger seat contrary to proper child-seating or restraint usage
recommendations. Even with this technology, parents are STRONGLY
encouraged to always properly restrain children in the rear seat. The
sensor also turns off the air bag(s) when the passenger seat is empty to
prevent unnecessary replacement of the air bag(s) after a collision.

Front safety belt usage sensors

The front safety belt usage sensors detect whether or not the driver and
front outboard passenger safety belts are fastened. This information
allows your Personal safety system to tailor the air bag deployment and
safety belt pretensioner activation depending upon safety belt usage.
Refer to Safety belt section in this chapter.

Front safety belt pretensioners

The safety belt pretensioners at the front outboard seating positions are
designed to tighten the safety belts firmly against the occupant’s body
during a frontal or near-frontal collision. This maximizes the effectiveness
of the safety belts and helps properly position the occupant relative to
the air bag to improve protection. The safety belt pretensioners can be
either activated alone or, if the collision is of sufficient severity, together
with the air bags.

Front safety belt energy management retractors

The front safety belt energy management retractors allow webbing to be
pulled out of the retractor in a gradual and controlled manner in
response to the occupant’s forward momentum. This helps reduce the

93

Seating and Safety Restraints

risk of force-related injuries to the occupant’s chest by limiting the load
on the occupant. Refer to Energy management feature section in this
chapter.

Determining if the Personal safety system is operational

The Personal safety system uses a warning light in the instrument cluster
or a back-up tone to indicate the condition of the system. Refer to the
Warning light section in the Instrument cluster chapter. Routine
maintenance of the Personal safety system is not required.

The Restraints control module (RCM) monitors its own internal circuits
and the circuits for the air bag supplemental restraints, crash sensor(s),
safety belt pretensioners, front safety belt buckle sensors, driver seat
position sensor, and passenger occupant classification sensor. In addition,
the RCM also monitors the restraints warning light in the instrument
cluster. A difficulty with the system is indicated by one or more of the
following.

• The warning light will either flash or stay lit.

• The warning light will not illuminate immediately after ignition is

turned on.

• A series of five beeps will be heard. The tone pattern will repeat
periodically until the problem and warning light are repaired.

If any of these things happen, even intermittently, have the Personal
safety system serviced at your dealership or by a qualified technician
immediately. Unless serviced, the system may not function properly in
the event of a collision.

Safety restraints precautions

Always drive and ride with your seatback upright and the lap
belt snug and low across the hips.

To reduce the risk of injury, make sure children sit where they
can be properly restrained.

Never let a passenger hold a child on his or her lap while the
vehicle is moving. The passenger cannot protect the child from

injury in a collision.

94

Seating and Safety Restraints

All occupants of the vehicle, including the driver, should always
properly wear their safety belts, even when an air bag (SRS) is

provided.

It is extremely dangerous to ride in a cargo area, inside or

outside of a vehicle. In a collision, people riding in these areas
are more likely to be seriously injured or killed. Do not allow people to
ride in any area of your vehicle that is not equipped with seats and
safety belts. Be sure everyone in your vehicle is in a seat and using a
safety belt properly.

In a rollover crash, an unbelted person is significantly more likely

to die than a person wearing a safety belt.

Each seating position in your vehicle has a specific safety belt

assembly which is made up of one buckle and one tongue that
are designed to be used as a pair. 1) Use the shoulder belt on the
outside shoulder only. Never wear the shoulder belt under the arm.

2) Never swing the safety belt around your neck over the inside
shoulder. 3) Never use a single belt for more than one person.

Always transport children 12 years old and under in the back

seat and always properly use appropriate child restraints.

Safety belts and seats can become hot in a vehicle that has been

closed up in sunny weather; they could burn a small child. Check
seat covers and buckles before you place a child anywhere near them.

95

Seating and Safety Restraints

Combination lap and shoulder belts

1. Insert the belt tongue into the
proper buckle (the buckle closest to
the direction the tongue is coming
from) until you hear a snap and feel
it latch. Make sure the tongue is
securely fastened in the buckle.

2. To unfasten, push the release
button and remove the tongue from
the buckle.

Energy management feature

• This vehicle has a seat belt system with an energy management
feature at the front outboard seating positions to help further reduce
the risk of injury in the event of a head-on collision.

• This seat belt system has a retractor assembly that is designed to pay
out webbing in a controlled manner. This feature is designed to help
reduce the belt force acting on the occupant’s chest.

The front outboard and rear safety restraints in the vehicle are
combination lap and shoulder belts. The front outboard passenger and
rear seat safety belts have three types of locking modes described below:

Vehicle sensitive mode

This is the normal retractor mode, which allows free shoulder belt length
adjustment to your movements and locking in response to vehicle
movement. For example, if the driver brakes suddenly or turns a corner
sharply, or the vehicle receives an impact of approximately 8 km/h (5
mph) or more, the combination safety belts will lock to help reduce
forward movement of the driver and passengers.

96

Seating and Safety Restraints

Webbing extraction sensitive mode

The webbing extraction sensitive mode stops the belt webbing from
retracting if it is pulled out too quickly.

Automatic locking mode

In this mode, the shoulder belt is pre-locked. The belt will still retract to
remove any slack in the shoulder belt.

The automatic locking mode is not available on the driver safety belt.

When to use the automatic locking mode

• Any time a child safety seat is installed in a passenger front outboard
or any rear seating position. Children 12 years old and under should
be properly restrained in the rear seat whenever possible. Refer to
Safety Restraints for Children or Safety Seats for Children later in
this chapter.

How to use the automatic locking mode

• Buckle the combination lap and
shoulder belt.

• Grasp the shoulder portion and
pull downward until the entire
belt is pulled out.

• Allow the belt to retract. As the belt retracts, you will hear a clicking
sound. This indicates the safety belt is now in the automatic locking
mode.

97

Seating and Safety Restraints

How to disengage the automatic locking mode

Ford Motor Company recommends that all passenger safety belt

assemblies and attaching hardware should be inspected by a
qualified technician after any collision to verify that the 9automatic
locking retractor9 feature for child seats is still working properly. Safety
belt assemblies should be inspected according to the procedures in the
Workshop Manual and replaced if either damage or improper operation
is noted. Failure to replace the belt and retractor assembly could
increase the risk of injury in a collision.

Unbuckle the combination lap/shoulder belt and allow it to retract
completely to disengage the automatic locking mode and activate the
vehicle sensitive (emergency) locking mode.

Front safety belt height adjustment

Your vehicle has safety belt height
adjustments for the driver and front
outboard passenger. Adjust the
height of the shoulder belt so the
belt rests across the middle of your
shoulder.

To lower the shoulder belt height,
push the button and slide the height
adjuster down. To raise the height
of the shoulder belt, push the
button and slide the height adjuster
up. Pull down on the height adjuster to make sure it is locked in place.

Position the safety belt height adjusters so that the belt rests

across the middle of your shoulder. Failure to adjust the safety
belt properly could reduce the effectiveness of the seat belt and
increase the risk of injury in a collision.

Safety belt warning light and indicator chime

The safety belt warning light illuminates in the instrument cluster and a
chime sounds to remind the occupants to fasten their safety belts.

98

Seating and Safety Restraints

Conditions of operation

If... Then...

The driver’s safety belt is not
buckled before the ignition switch
is turned to the ON position...

The driver’s safety belt is buckled
while the indicator light is
illuminated and the warning chime
is sounding...

The driver’s safety belt is buckled
before the ignition switch is turned
to the ON position...

BeltMinder

The BeltMinder feature is a supplemental warning to the safety belt
warning function. This feature provides additional reminders by
intermittently sounding a chime and illuminating the safety belt warning
lamp in the instrument cluster when the driver’s safety belt is unbuckled.

The BeltMinder feature uses information from the passenger occupant
classification sensor to determine if a front seat passenger is present and
therefore potentially in need of a warning. To avoid activating the
BeltMinder feature for objects placed in the front passenger seat,
warnings will only be given to large front seat occupants as determined
by the passenger occupant classification sensor.

Both the driver’s and passenger’s safety belt usages are monitored and
either may activate the BeltMinder feature. The warnings are the same
for the driver and the front passenger. If the BeltMinder warnings have
expired (warnings for approximately 5 minutes) for one occupant (driver
or front passenger), the other occupant can still activate the BeltMinder
feature.

The safety belt warning light
illuminates 1-2 minutes and the
warning chime sounds 4-8
seconds.

The safety belt warning light and
warning chime turn off.

The safety belt warning light and
indicator chime remain off.

99