Mercia Garden Products 04LEAN0804-V1 Instruction manual
General Instructions
Please retain product label and instructions for future reference
04LEAN0804-V1
8X4 GREENHOUSE LEAN-TO
BEFORE YOU START PLEASE READ INSTRUCTIONS CAREFULLY
- Check the pack and make sure you have all the parts listed.
- When you are ready to start, make sure you have the right tools at hand (not supplied)
including a Phillips screwdriver, Stanley knife, wood saw, step ladder and drill with 2mm
bit.
- Ensure there is plenty of space and a clean dry area for assembly.
TIMBER
As with all natural materials, timber can be aected during various weather conditions.
For the duration of heavy or extended periods of rain, swelling of the wood panels may
occur. Warping of the wood may also occur during excessive dry spells due to an interior
moisture loss. Unfortunately, these processes cannot be avoided but can be helped. It is
suggested that the outdoor building is sprayed with water during extended periods of
warm sunshine and sheltered as much as possible during rain or snow.
x2
2mm Drill bit
**Protim Aquatan T5 (621)**
Your building has been treated with Aquatan.
Aquatan is a water-based concentrate which is diluted with water, the building as been treated by the correct
application of Aquatan solution and then allowed to dry.
Aquatan is a decorative nish to colour the wood, which is applied industrially to timber fence panels and
garden buildings.
All building’s should be
erected by two adults
For ease of assembly, you
MUST pilot drill all screw
holes and ensure all screw
heads are countersunk.
Winter = High Moisture = Expansion
Summer = Low Moisture = Contraction
CAUTION
Every eort has been made during the
manufacturing process to eliminate the
prospect of splinters on rough surfaces of the
timber. You are strongly advised to wear gloves
when working with or handling rough sawn
timber.
Our buildings are pre treated with a water based treatment**; this only helps to protect
the product during transit and for upto 3 months against mould. To validate your
guarantee and ensure longevity of the product, it is ESSENTIAL the building is treated
with a wood preserver within the rst three months of assembly and thereafter in
accordance with the manufactures recommendations. Care must be taken to ensure
the product is placed on a suitable base.
BUILDING A BASE
When thinking about where the building and base is going to be constructed:
Ensure that there will be access to all sides for maintenance work and annual
treatment.
Ensure the base is level and is built on rm ground, to prevent distortion. Refer to
diagrams for the base dimensions, The base should be slightly smaller than the external
measurement of the building, i.e. The cladding should overlap the base, creating a run
o for water. It is also recommended that the oor be at least 25mm above the
surrounding ground level to avoid ooding.
TYPES OF BASE
- Concrete 75mm laid on top of 75mm hard-core.
- Slabs laid on 50mm of sharp sand.
Whilst all products manufactured are made to the highest standards of Safety and in
the case of childrens products independently tested to EN71 level, we cannot accept
responsibility for your safety whilst erecting or using this product.
Aquatan undiluted contains: boric acid, sodium hydroxide 32% solution, aqueos mixture of sodium dioctyl
sulphosuccinat and alcohols: 2, 4, 6-trichlorophenol.
For assistance please contact customer care on: 01636 880514
Mercia Garden Products Limited,
Sutton On Trent,
Newark,
Nottinghamshire,
NG23 6QN
Refer to the instructions pages for you specic product code
www.merciagardenproducts.co.uk
04LEAN0804-V1
Please retain product label and instructions for future reference
Overall Dimensions:
Length = 2492m
Width = 1357mm
Height = 2070mm
Base Dimensions:
Length = 2492mm
Width = 1312mm
Before assembly
please make sure you have a
suitable base ready to erect your
building
MADE IN GREAT BRITAIN
Please note that we don't include xings with this product due to wall construction materials varying from house to
house. If you are unsure on the xings you require then we recommend that you consult with your local builders
merchant or a knowledgeable DIY store.
Fixing Kit
9
Cover strip -1262mm x2
10
Vertical Beading strip -1720mm x2
11
Large panel joist - 2380mm
12
Small panel joist -1306mm x2
13
Horizontal Beading strip -580mm
14
Window block- 650mm
Content
1
Rear panel
4
x3 Small
15
hinge
2
3
16
19
Casement Stay
Large side panel
5
Door panel
Nail Bag
6
x2 Long
hinge
20
Key Plate
2x Mortice lock
17
Handle
70mm Screw x 31
50mm Screw x 16
18
Mortice Lock
Roof panel
Gable top left
7
Opening Window
Gable top right
Door8
40mm Screw x 6
30mm Screw x 37
30mm Black Screw x 20
20mm Black Screw x 4
P 2
Please retain product label and instructions for future reference
Step 1
Remove transportation blocks
from the bottom of each panel
before beginning assembly.
Each Panel should have two
blocks.
Step 3
Fit the mortice lock into the recess
and x in place with the screws
provided. Fit the key plate to the
inside of the door panel using the
screws provided.
30mm
screw
The Mortice Lock is Reversible
Step 2
Attatch the door to the door
gable using 7x30mm Screws
for each long hinge. and
8x30mm screws for the small
hinge
18
20
4x30mm Screws
16
Step 4
Fix the vertical and horizontal
beading to the door gable.
Ensure that the beading sits
ush with the back of the
8
30mm
screw
door gable as shown in the
detailed vew.
13
15
10
30mm
screw
22x30mm Screws
3
11x30mm Screws
P 3
Loading...