Mercia Garden Products 03WES1008-V1 Instruction manual
General Instructions
Please retain product label and instructions for future reference
03WES1008-V1
10X8 SUMMERHOUSE, T&G ROOF AND FLOOR, DOUBLE DOORS, OPENING WINDOW AND
VERANDA
BEFORE YOU START PLEASE READ INSTRUCTIONS CAREFULLY
- Check the pack and make sure you have all the parts listed.
- When you are ready to start, make sure you have the right tools at hand (not supplied)
including a Phillips screwdriver, Stanley knife, wood saw, step ladder and drill with 2mm
bit.
- Ensure there is plenty of space and a clean dry area for assembly.
TIMBER
As with all natural materials, timber can be aected during various weather conditions.
For the duration of heavy or extended periods of rain, swelling of the wood panels may
occur. Warping of the wood may also occur during excessive dry spells due to an interior
moisture loss. Unfortunately, these processes cannot be avoided but can be helped. It is
suggested that the outdoor building is sprayed with water during extended periods of
warm sunshine and sheltered as much as possible during rain or snow.
x2
2mm Drill bit
**Protim Aquatan T5 (621)**
Your building has been treated with Aquatan.
Aquatan is a water-based concentrate which is diluted with water, the building as been treated by the correct
application of Aquatan solution and then allowed to dry.
All building’s should be
erected by two adults
For ease of assembly, you
MUST pilot drill all screw
holes and ensure all screw
heads are countersunk.
Winter = High Moisture = Expansion
Summer = Low Moisture = Contraction
CAUTION
Every eort has been made during the
manufacturing process to eliminate the
prospect of splinters on rough surfaces of the
timber. You are strongly advised to wear gloves
when working with or handling rough sawn
timber.
Our buildings are pre treated with a water based treatment**; this only helps to protect
the product during transit and for upto 3 months against mould. To validate your
guarantee and ensure longevity of the product, it is ESSENTIAL the building is treated
with a wood preserver within the rst three months of assembly and thereafter in
accordance with the manufactures recommendations. Care must be taken to ensure
the product is placed on a suitable base.
BUILDING A BASE
When thinking about where the building and base is going to be constructed:
Ensure that there will be access to all sides for maintenance work and annual
treatment.
Ensure the base is level and is built on rm ground, to prevent distortion. Refer to
diagrams for the base dimensions, The base should be slightly smaller than the external
measurement of the building, i.e. The cladding should overlap the base, creating a run
o for water. It is also recommended that the oor be at least 25mm above the
surrounding ground level to avoid ooding.
P 1
TYPES OF BASE
- Concrete 75mm laid on top of 75mm hard-core.
- Slabs laid on 50mm of sharp sand.
Whilst all products manufactured are made to the highest standards of Safety and in
the case of childrens products independently tested to EN71 level, we cannot accept
responsibility for your safety whilst erecting or using this product.
Aquatan is a decorative nish to colour the wood, which is applied industrially to timber fence panels and
garden buildings.
Aquatan undiluted contains: boric acid, sodium hydroxide 32% solution, aqueos mixture of sodium dioctyl
sulphosuccinat and alcohols: 2, 4, 6-trichlorophenol.
For assistance please contact customer care on: 01636 880514
Mercia Garden Products Limited,
Sutton On Trent,
Newark,
Nottinghamshire,
NG23 6QN
Refer to the instructions pages for you specic product code
www.merciagardenproducts.co.uk
03WES1008-V1
Please retain product label and instructions for future reference
Fixing Kit
Overall Dimensions:
Length = 3422mm
Width = 2830mm
Height = 2252m
Base Dimensions:
Length = 3124mm
Width = 2413mm
Before assembly
please make sure you have a
suitable base ready to erect your
building
MADE IN GREAT BRITAIN
Building Content
13
Veranda Support - 27x44x1685mm Qty 2
14
Fascia - 12x95x1549mm Qty 4
15
Door Strip - 12x60x800mm Qty 2
16
Window Strip - 12x45x1055mm Qty 1
17
Tower Bolt Strip - 19x45x140mm Qty 2
18
Cover Trims - 12x30x1680mm Qty 4
19
Door Beading Strip - 12x17x1710mm Qty 2
1
Door Gable
5
Floor Qty 2
10
2
Plain Gable Plain Side
6
Veranda Floor
Roof Qty 4
11
20
Door Beading Strip - 12x17x1207mm Qty 1
3
4
21
Roof Support - 27x70x2315mm Qty 1
22
Roof Support Block - 27x70x655mm Qty 2
23
Window Beading Strip - 12x17x437mm Qty 8
Window Side
24
Window Beading Strip - 12x17x348mm Qty 8
8
7
Master
Door
12
9
Slave
Door
25
30
32
Finial x2
Press Lock
26
Handle
Thinge
Qty 4
31
Turn Button
33
Corner
Bracing
27
Hinge
Qty 4
28
Tower Bolt
Qty 2
29
Casement
Stay
50mm Screw x 86
40mm Screw x 24
30mm Screw x 61
30mm Black Screw x 73
20mm Screw x 6
Veranda Rail
Qty 2
Opening Window
Glazing
Qty 4
Felt
34
U Channel
Qty 2
35
Nail Bag
16mm Black Screw x 6
25mm Nails x 64
Felt Tacks x 150
P 10
Please retain product label and instructions for future reference
Pre Assembly
Remove transportation
blocks from the bottom
of each panel before
beginning assembly. Each
Panel should have two
Step 1
Fix a Thinge to the top and bottom of each
door and a hinge in the middle and x to
the door gable using 30mm black screws.
1
26
27
8
26
9
26
27
30mm
screw
Pre drill
hole
Insert the glazing sheet into the window rebate, ensure a
ush t. Attach window beading with the 25mm glazing
pins provided, x4 pins per beading. When nailing pins
protect the glazing sheet with a piece of cardboard or
similar to avoid breakage and scratches.
23
24
12
26
27
26
44 x 30mm black screws
64x 25mm glazing pins
P 11
Loading...