Mercia Garden Products 01OVLPRA0806SDFW-V1 Instruction manual

General Instructions
Please retain product label and instructions for future reference
8X6 OVERLAP REVERSE APEX
BEFORE YOU START PLEASE READ INSTRUCTIONS CAREFULLY
- Check the pack and make sure you have all the parts listed.
- When you are ready to start, make sure you have the right tools at hand (not supplied) including a Phillips screwdriver, Stanley knife, wood saw, step ladder and drill with 2mm bit.
- Ensure there is plenty of space and a clean dry area for assembly.
TIMBER
As with all natural materials, timber can be aected during various weather conditions. For the duration of heavy or extended periods of rain, swelling of the wood panels may occur. Warping of the wood may also occur during excessive dry spells due to an interior moisture loss. Unfortunately, these processes cannot be avoided but can be helped. It is suggested that the outdoor building is sprayed with water during extended periods of warm sunshine and sheltered as much as possible during rain or snow.
x2
2mm Drill bit
**Protim Aquatan T5 (621)**
Your building has been treated with Aquatan.
Aquatan is a water-based concentrate which is diluted with water, the building as been treated by the correct application of Aquatan solution and then allowed to dry.
Aquatan is a decorative nish to colour the wood, which is applied industrially to timber fence panels and garden buildings.
All building’s should be erected by two adults
For ease of assembly, you MUST pilot drill all screw holes and ensure all screw heads are countersunk.
Winter = High Moisture = Expansion Summer = Low Moisture = Contraction
CAUTION
Every eort has been made during the manufacturing process to eliminate the prospect of splinters on rough surfaces of the timber. You are strongly advised to wear gloves when working with or handling rough sawn timber.
Our buildings are pre treated with a water based treatment**; this only helps to protect the product during transit and for upto 3 months against mould. To validate your guarantee and ensure longevity of the product, it is ESSENTIAL the building is treated with a wood preserver within the rst three months of assembly and thereafter in accordance with the manufactures recommendations. Care must be taken to ensure the product is placed on a suitable base.
BUILDING A BASE
When thinking about where the building and base is going to be constructed: Ensure that there will be access to all sides for maintenance work and annual treatment.
Ensure the base is level and is built on rm ground, to prevent distortion. Refer to diagrams for the base dimensions, The base should be slightly smaller than the external measurement of the building, i.e. The cladding should overlap the base, creating a run o for water. It is also recommended that the oor be at least 25mm above the surrounding ground level to avoid ooding.
TYPES OF BASE
- Concrete 75mm laid on top of 75mm hard-core.
- Slabs laid on 50mm of sharp sand.
Whilst all products manufactured are made to the highest standards of Safety and in the case of childrens products independently tested to EN71 level, we cannot accept responsibility for your safety whilst erecting or using this product.
Aquatan undiluted contains: boric acid, sodium hydroxide 32% solution, aqueos mixture of sodium dioctyl sulphosuccinat and alcohols: 2, 4, 6-trichlorophenol.
For assistance please contact customer care on: 01636 880514
Mercia Garden Products Limited, Sutton On Trent, Newark, Nottinghamshire, NG23 6QN
Refer to the instructions pages for you specic product code
www.merciagardenproducts.co.uk
01OVLPRA0806SDFW-V1
Please retain product label and instructions for future reference
Overall Dimensions:
Length = 1905mm
Width = 2414mm
Height = 2216mm
Base Dimensions:
Length = 1753mm
Width = 2350mm
Before assembly
please make sure you have a
suitable base ready to erect your
building
MADE IN GREAT BRITAIN
Building content
1
Nail Bag
Felt Tacks x 100
20mm Screw x 8
30mm Black Screw x 2
30mm Screw x 58
40mm Screw x 40
50mm Screw x 30
Pre Assembly
Remove transportation blocks from the bottom of each panel before beginning assembly. Each Panel should have two
3
2
4
5
Door Panel
6
Roof Sheet
Qty 2
7
8
9
10
11
12
13
Plain Panel
Ridge Bar - 2304mm Qty 1
Cover Trim - 1800mm Qty 4
Eaves Frame - 1195mm Qty 4
Door Strip - 1590mm Qty 2
Fascia - 1016mm Qty 4
Door Block- 140mm Qty 1
Finial x2
Plain Gable
Qty 2
14
T Hinge Qty 2
17
Pad Bolt
Qty 1
Floor
15
Turn Button
Qty 2
18
Felt
L-Bracket
Qty 2
19
Capping
Felt
16
Door
Fix the T Hinges onto the door and door frame as shown. Ensure that the screws go through the cladding and into the framing behind.
14x30mm screws
14
30mm
Pre drill
hole
screw
1
5
P 12
Loading...
+ 4 hidden pages