Mercia Garden Products 01OAOSB0705-V2 Instruction manual
01OAOSB0705-V2
Please retain product label and instructions for future reference
Overall Dimensions:
Length = 1843mm
Width = 2257mm
Height = 2205mm
Base Dimensions:
Length = 1448mm
Width = 2082mm
Before assembly
please make sure you have a
suitable base ready to erect your
building
MADE IN GREAT BRITAIN
BEFORE YOU START PLEASE READ INSTRUCTIONS CAREFULLY
- Check the pack and make sure you have all the parts listed.
- When you are ready to start, make sure you have the right tools at hand
(not supplied) including a Phillips screwdriver, Stanley knife, wood saw,
step ladder and drill with 2mm bit.
- Ensure there is plenty of space and a clean dry area for assembly.
TIMBER
As with all natural materials, timber can be aected during various weather
conditions. For the duration of heavy or extended periods of rain, swelling of the
wood panels may occur. Warping of the wood may also occur during excessive
dry spells due to an interior moisture loss. Unfortunately, these processes cannot
be avoided but can be helped. It is suggested that the outdoor building is
sprayed with water during extended periods of warm sunshine and sheltered as
much as possible during rain or snow.
Our buildings are pre treated with a water based treatment**; this only helps to
protect the product during transit and for upto 3 months against mould. To
validate your guarantee and ensure longevity of the product, it is ESSENTIAL the
building is treated with a wood preserver within the rst three months of
assembly and thereafter in accordance with the manufactures recommendations. Care must be taken to ensure the product is placed on a suitable base.
x2
2mm Drill bit
All building’s should be erected by two
adults
For ease of assembly, you must pilot
drill all screw holes and ensure all
screw heads are countersunk.
Winter = High Moisture = Expansion
Summer = Low Moisture = Contraction
CAUTION
Every eort has been made during the
manufacturing process to eliminate the
prospect of splinters on rough surfaces
of the timber. You are strongly advised
to wear gloves when working with or
handling rough sawn timer.
1
Front Gable
4
Small Side Panel
Fixing Kit
9
Roof Eave Framing - 1795mm QTY 2
10
Large Strip - 1662mm QTY 2
5
Floor
2
Back Gable Side Panel
6
Roof
Small Roof
3
7
8
Door
BUILDING A BASE
When thinking about where the building and base is going to be constructed:
Ensure that there will be access to all sides for maintenance work and annual
treatment.
Ensure the base is level and is built on rm ground, to prevent distortion. Refer
to diagrams for the base dimensions, The base should be slightly smaller than
the external measurement of the building, i.e. The cladding should overlap the
base, creating a run o for water. It is also recommended that the oor be at
least 25mm above the surrounding ground level to avoid ooding.
TYPES OF BASE
- Concrete 75mm laid on top of 75mm hard-core.
- Slabs laid on 50mm of sharp sand.
Whilst all products manufactured are made to the
highest standards of Safety and in the case of childrens
products independently tested to EN71 level, we cannot
accept responsibility for your safety whilst erecting or
using this product.
Mercia Garden Products Limited, Sutton On Trent, Newark, Nottinghamshire, NG23 6QN
www.merciagardenproducts.co.uk
For Assistance Please
Contact Customer Care on
01636 880514
**Protim Aquatan T5 (621)**
Your building has been treated with Aquatan.
Aquatan is a water-based concentrate which is diluted with water, the
building as been treated by the correct application of Aquatan
solution and then allowed to dry. Aquatan is a decorative nish to
colour the wood, which is applied industrially to timber fence panels
and garden buildings.
Aquatan undiluted contains: boric acid, sodium hydroxide 32%
solution, aqueos mixture of sodium dioctyl sulphosuccinat and
alcohols: 2, 4, 6-trichlorophenol.
11
Door Strip - 1590mm QTY 2
12
Small Strip - 1529mm QTY 2
13
Ridge Bar - 1448mm QTY 1
14
Large Fascia - 1410mm QTY 2
15
Small Fascia - 1000mm QTY 2
16
Fascia Block - 140mm QTY 1
17
Support Block- 495mm QTY 3
18
Diamond Finial - QTY 2
P 1
Please retain product label and instructions for future reference
Felt
19
20
Corner Bracing
Step 1
Remove transportation blocks
from the bottom of each panel
before beginning assembly. Each
Panel should have two blocks.
21
Pad bolt
T-Hinge x3
22
Nail Bag
50mm Screw x 28
40mm Screw x 22
30mm Screw x 91
Felt Tacks x 80
Step 3
Fix the T-hinge to the door
using 30mm screws ensuring
that the screws go through
to the door framing.
1mm
8
21
Step 2
Place the floor on a firm and
level base, ensure base has
suitable drainage free from
areas where standing water can
collect. (See front page on base
requirements).
21 x 30mm Screws
Attach the door strips to the
inside of the door aperture
using 30mm screws.
11
11
5
6 x 30mm Screws
P 2
Loading...