Mercia Garden Products 01BEACH-V1 Instruction manual
General Instructions
Please retain product label and instructions for future reference
01BEACH-V1
BEACH HUT
BEFORE YOU START PLEASE READ INSTRUCTIONS CAREFULLY
- Check the pack and make sure you have all the parts listed.
- When you are ready to start, make sure you have the right tools at hand (not supplied)
including a Phillips screwdriver, Stanley knife, wood saw, step ladder and drill with 2mm
bit.
- Ensure there is plenty of space and a clean dry area for assembly.
TIMBER
As with all natural materials, timber can be aected during various weather conditions.
For the duration of heavy or extended periods of rain, swelling of the wood panels may
occur. Warping of the wood may also occur during excessive dry spells due to an interior
moisture loss. Unfortunately, these processes cannot be avoided but can be helped. It is
suggested that the outdoor building is sprayed with water during extended periods of
warm sunshine and sheltered as much as possible during rain or snow.
Our buildings are pre treated with a water based treatment**; this only helps to protect
the product during transit and for upto 3 months against mould. To validate your
guarantee and ensure longevity of the product, it is ESSENTIAL the building is treated
with a wood preserver within the rst three months of assembly and thereafter in
accordance with the manufactures recommendations. Care must be taken to ensure
the product is placed on a suitable base.
x2
2mm Drill bit
**Protim Aquatan T5 (621)**
Your building has been treated with Aquatan.
Aquatan is a water-based concentrate which is diluted with water, the building as been treated by the correct
application of Aquatan solution and then allowed to dry.
Aquatan is a decorative nish to colour the wood, which is applied industrially to timber fence panels and
garden buildings.
Aquatan undiluted contains: boric acid, sodium hydroxide 32% solution, aqueos mixture of sodium dioctyl
sulphosuccinat and alcohols: 2, 4, 6-trichlorophenol.
All building’s should be
erected by two adults
For ease of assembly, you
MUST pilot drill all screw
holes and ensure all screw
heads are countersunk.
Winter = High Moisture = Expansion
Summer = Low Moisture = Contraction
CAUTION
Every eort has been made during the
manufacturing process to eliminate the
prospect of splinters on rough surfaces of the
timber. You are strongly advised to wear gloves
when working with or handling rough sawn
timber.
BUILDING A BASE
When thinking about where the building and base is going to be constructed:
Ensure that there will be access to all sides for maintenance work and annual
treatment.
Ensure the base is level and is built on rm ground, to prevent distortion. Refer to
diagrams for the base dimensions, The base should be slightly smaller than the external
measurement of the building, i.e. The cladding should overlap the base, creating a run
o for water. It is also recommended that the oor be at least 25mm above the
surrounding ground level to avoid ooding.
TYPES OF BASE
- Concrete 75mm laid on top of 75mm hard-core.
- Slabs laid on 50mm of sharp sand.
Whilst all products manufactured are made to the highest standards of Safety and in
the case of childrens products independently tested to EN71 level, we cannot accept
responsibility for your safety whilst erecting or using this product.
For assistance please contact customer care on: 01636 880514
Mercia Garden Products Limited,
Sutton On Trent,
Newark,
Nottinghamshire,
NG23 6QN
Refer to the instructions pages for you specic product code
www.merciagardenproducts.co.uk
03BEACH-V1
Overall Dimensions:
Length = 3280mm
Width = 2373mm
Height = 2860mm
Base Dimensions:
Length = 2122mm
Width = 3256mm
Before assembly
please make sure you have a
suitable base ready to erect your
building
Please retain product label and instructions for future reference
80mm Bolt x4
35mm Bolt x4
150mm Screw x16
100mm Screw x60
60mm Screw x38
50mm Screw x100
40mm Screws x58
30mm Screws x38
30mm Blk Screws x6
20mm Screws x20
10mm Screws x8
Felt Tacks x130
MADE IN GREAT BRITAIN
1 2 3 4 5 6 7
Door
Gable
8 9
Plain
Side
QTY 2
10 11
Plain
Gable
Veranda
Side Panel
QTY 2
12
Ladder Side - 760mm L & R
Veranda
Front Panel
QTY 2
Gable Top Floor
13
Ladder Step - 760mm QTY 2
14
Deck Boards - 2122mm QTY 8
Roof
QTY 4
Master
Door
Slave
Door
Base
QTY 2
15
Tower Block - 400mm QTY 14
27
Ladder Block QTY 4
Pre Assembly
Remove transportaion blocks from the
panels before beginning assembly.
Step 1
Fix the bases together along the
longer side using 4x80mm bolts.
4x80mm Bolts
Pre drill
hole
80mm
Bolt
11
16
Tower Brace - 400mm QTY 28
17
Cover Trim - 265mm QTY 2
18
Cover Trim - 1875mm QTY 2
19
Fascia - 1299mm QTY 4
20
21
Finial QTY 2
Fascia Block - 140mm QTY 2
22
23
24
25
26
Butt Hinge QTY 6
Chrome Handle QTY 2
Turn Button QTY 2
11
Press Lock
Barrel Bolt QTY 2
P 2
Please retain product label and instructions for future reference
Step 2
Fix the base blocks to the base using 1x100mm
screw per block.
See illustration for block positioning.
14x150mm Screws
Pre drill
hole
150mm
screw
15
Step 4
Attach the ladder blocks onto the
edge of each ladder step using
2x60mm screws per block.
Secure each step to the ladder
sides with 4x60mm per step.
Repeat this process for both sides.
*Ensure the steps are level before
continuing.
16x60mm Screws
Pre drill
hole
60mm
screw
12
13
27
13
27
Step 3
Secure the blocks to the base with
the tower braces. Ensure to line the
braces up with the base timbers,
xing in place with 2x100mm
screws per brace.
56x100mm Screws
Pre drill
hole
100mm
screw
16
Step 5
Screw the fully assembled ladder
to the tower base with 2x100mm
screws, approximately in the
centre of the base.
2x100mm Screws
Pre drill
hole
100mm
screw
16
P 3
Loading...