Mercia Garden 01PTSHPMOW4803-V2 User manual

General Instructions

Please retain product label and instructions for future reference

01PTSHPMOW4803-V2

Pressure Treated Shiplap Mower Store

BEFORE YOU START PLEASE READ INSTRUCTIONS CAREFULLY

- Check the pack and make sure you have all the parts listed.

- When you are ready to start, make sure you have the right tools at hand (not supplied) including a Phillips
screwdriver, Stanley knife, wood saw, step ladder and drill with 2mm bit.

- Ensure there is plenty of space and a clean dry area for assembly.

TIMBER

As with all natural materials, timber can be aected during various weather conditions. For the duration of
heavy or extended periods of rain, swelling of the wood panels may occur. Warping of the wood may also
occur during excessive dry spells due to an interior moisture loss. Unfortunately, these processes cannot be
avoided but can be helped. It is suggested that the outdoor building is sprayed with water during extended
periods of warm sunshine and sheltered as much as possible during rain or snow.

Once your garden building has been installed it will need to be treated as soon as possible and annually to
prevent the timber from deteriorating and to waterproof it. This is required to maintain the anti-rot guarantee.

Dip Treated buildings - Require a preservative treatment to protect against rot and decay and a waterproof
treatment to prevent water ingress

x2

2mm Drill bit

Pressure Treated Timber

Pressure treating is a chemical process which helps to protect wood against adverse weather which could
lead to rot or insect damage.

The most common chemicals used to pressure treat wood are Alkaline Copper Quaternary (ACQ),
Copper Azole (CA), and Micronized Copper Quaternary (MCQ).

Safety: Always wear gloves, eye protection and a dust mask when handling wood. Due to chemicals in
pressure treated wood, never burn its sawdust or scraps; instead dispose in a landll.

All building’s should be
erected by two adults

For ease of assembly, you
MUST pilot drill all screw
holes and ensure all screw
heads are countersunk.

Winter = High Moisture = Expansion
Summer = Low Moisture = Contraction

CAUTION

Every eort has been made during the
manufacturing process to eliminate the
prospect of splinters on rough surfaces of the
timber. You are strongly advised to wear gloves
when working with or handling rough sawn
timber.

Pressure Treated buildings - Require a waterproof treatment to prevent water ingress

Log Cabins - Are supplied untreated and require a preservative and waterproong treatment.

BUILDING A BASE

When thinking about where the building and base is going to be constructed:
Ensure that there will be access to all sides for maintenance work and annual
treatment.

Ensure the base is level and is built on rm ground, to prevent distortion. Refer to diagrams for the base
dimensions, The base should be slightly smaller than the external measurement of the building, i.e. The
cladding should overlap the base, creating a run o for water. It is also recommended that the oor be at least
25mm above the surrounding ground level to avoid ooding.

TYPES OF BASE

- Concrete 75mm laid on top of 75mm hard-core.

- Slabs laid on 50mm of sharp sand.

Whilst all products manufactured are made to the highest standards of Safety and in the case of childrens
products independently tested to EN71 level, we cannot accept responsibility for your safety whilst erecting
or using this product.

For assistance please contact customer care on: 01636 880514

Mercia Garden Products Limited,
Sutton On Trent,
Newark,
Nottinghamshire,
NG23 6QN

Refer to the instructions pages for you specic product code

www.merciagardenproducts.co.uk

01PTSHPMOW4803-V2

Please retain product label and instructions for future reference

Overall Dimensions:

Length = 1450mm

Width = 951mm

Height = 1421mm

Base Dimensions:

Length = 1395mm

Width = 910mm

Before assembly

please make sure you have a

suitable base ready to erect your

building

MADE IN GREAT BRITAIN

1

2

3

13

Pad bolt QTY 1

PI-07-0035

Pre Assembly

Remove transportation blocks
from the bottom of each panel
before beginning assembly. Each
Panel should have two blocks.

Turn button

14

QTY 2

PI-07-0034

15

T- Hinge QTY 4

PI-02-1043

Felt Tacks x80

60x30mm Screw

3x30mm Black Screw

10x40mm Screw

20x50mm Screw

6x20mm Screw

Back Panel QTY 1

AI-01SHPMOW4803BP-V2

5

Right Gable QTY 1

AI-01SHPMOW4803RG-V2

6

Left Gable QTY 1

AI-01SHPMOW4803LG-V2

7

Front Panel QTY 1

AI-01SHPMOW4803FP-V2

8

4

Floor QTY 1

AI-01SHPMOW4803F-V2

9

OSB Roof Sheet

Front Fasica QTY 1
12 x 95 x 1450mm

S1295-1450MM

10

Doors QTY 2

AI-01SHPMOW4803D-V2

Door Trims QTY 2
12 x 45 x 1264mm

S1245-1264MM

Side Fascias QTY 2

12 x 95 x 965mm

S1295-965MM

11

Felt

12

Door Strip QTY 2
12 x 45 x 590mm

S1245-590MM

P 2