Mensor CPT6010 Specifications

CPT6010 Digital Pressure Transducer

Applications

 High accuracy transfer standard
 Pressure standard in test & calibration stands
 Wind tunnels
 Hydrology, Oceanography
 Aerospace, Metrology

Features

Testing and
Calibration Technology

Data Sheet CPT6010 • 04/2015

 0.020% FS accuracy
 Ranges:

Absolute: 0-7.5 psia to 0-6000 psia

Gauge: 0-5 psig to 0-6000 psig

 Pneumatic or Hydraulic
 RS-232 or RS-485 communication
 303 stainless steel housing

Description

General

The CPT6010 Digital Pressure Transducer is a self-contained
pressure sensing device that provides high accuracy pressure
measurements in both the single and dual calibration models.
This transducer incorporates a low hysteresis silicon sensor with
electronically compensated pressure linearity over the specified
temperature range.

The CPT6010 Transducer is characterized over the full pressure
and temperature range to achieve 0.020% FS uncertainty. This
uncertainty specification includes linearity, hysteresis, repeat­ability and temperature errors. Also featured is an output which
is updated at a rate of 50 readings per second (20 ms).

Applications

The CPT6010 is used in OEM Applications where a high ac­curacy pressure sensing is required. It can also be used as a

Digital Pressure Transducer Model CPT6010

transfer standard or in pressure calibration and testing areas of
production facilities.

Functional Flexibility

The CPT6010 Digital Pressure Transducer is a high accuracy
pressure measurement component that uses either RS-232
or RS-485 to communicate with a host computer over long
distances. Any MS-DOS compatible PC with an available serial
output port can serve as the host controller.

System designers will appreciate the flexibility offered by having
highly accurate pressure transducers that are not tied to a front
panel and which may be located remotely. For remote operation
the transducer equipped with RS-485 can be located up to 4,000
feet from the host. A simple cable can accommodate both the
power and the two-way communications requirements.

Data Sheet CPT6010 • 04/2015 Page 1 of 2

Related Products:
CPT6100 and CPT6180 Digital Pressure Transducer
Pressure Systems

Specifications

Total Uncertainty

Calibration
Stability after
warmup

Calibration

Pressure Ranges

Special Pressure
Ranges

Pressure Units

Resolution

Overpressure
Limit

Compensated
Temp. Range

Warm-up

Reading Rate

Communications

Max.
Transmission

Multi-drop
Capacity

0.020%FS. Total uncertainty (k=2) includes
hysteresis, linearity, repeatability, reference
standard, drift and temperature effects over the
calibrated range for the calibration interval speci-

ed with periodic re-zeroing.

Less than 0.02% FS for six months.

Calibration Interval: 180 days
Cal Uncertainties: 0.020% FS
Calibration adjustment: Zero and Span. (Zero
and span may be reset via the serial interface

without affecting the linearity.)

Abs: 0-7.5 psia up to 0-6000 psia.
Gauge: 0-5 psig up to 0-6000 psig.

Vacuum or bidirectional ranges. Metric pressure
units also available.

Selected from a list of 35: psi, inHg @0°C and
60°F, inH2O @4°C, 20°C and 60°F, ftH2O @ 4°C,
20°C and 60°F, mTorr, inSW @ 0C, ftSW @ 0C,
ATM, bars, mbars, mmH2O @ 4°C, cm H2O @
4°C, MH2O @ 4°C, mmHg @ 0°C, cmHg @ 0°C,
Torr, hPa, mPa, kPa, Pa, D/cmsq, G/cmsq, Kg/
cmsq, mSW @ 0°C, OSI, PSF, TSF, TSI, µHg @

0°C, %fs. All seawater units are 3.5% salinity.

Up to 1 ppm, depending on measurement units
and range.

150% FS or greater, depending on range

15 to 45 °C

10 minutes to rated accuracy

50 Hz

RS-232 or RS-485. LabVIEW®1 drivers are avail­able.

4000 feet (RS-485)

The maximum number of RS-485 Series 6000

transducers which can be connected to a single

host computer is 31.

Mechanical
Shock

Case Size

Weight

Media
Compatibility

Fittings

Power

Compliance

Options

1

LabVIEW® is a trademark of National Instruments Corporation.

5g max.

1.75” wide x 6.0” long (4.45 x 15.24 cm), not

including pneumatic and electrical.

Approximately 12 ounces (28.3 grams).

All media compatible with 316L stainless steel.

Pressure Port: 1/4 inch male NPT

Reference Port: 1/16 inch barb (gauge instru­ments only)

9-18 VDC, 45mA @ 12 VDC
6 pin Bendix connector
#PT02E-10-6P

Conforms to CE standards EN 50081-1, EN
50082-1, EN 50081-2, and EN 50082-2.

Relief Valves —up to 1000 psig
Custom ranges.

The calibration program at Mensor is accredited by A2LA as

complying with both the ISO/IEC 17025:2005 and the ANSI/
NCSL Z540-1-1994 standards. All Mensor primary standards
are traceable to NIST. Mensor is registered to ISO9001:2008.

Since product innovation is a continuous process at Mensor,

we reserve the right to change specications without notice.

Represented by:

Mensor

201 Barnes Drive
San Marcos, Texas 78666
Toll Free: 800-984-4200
Tel: [phone]
Fax: [phone]
Email: [e-mail]

Data Sheet CPT6010 • 04/2015Page 2 of 2