USER GUIDE
USB SD/MMC
CARD READER
You Should Have
1.Memorex®USB SD/MMC
Card Reader.
2. 1x Card Reader installation
C D - R O M .
3 .C a rd Reader User Guide.
Please notify your distributor or
retailer if any of the above is
m i s s i n g .
SYSTEM COMPATIBILITY:
The Memorex Dual Card Reader is compatible with Windows®98/2000/
ME/SE and Apple 8.5 or higher with USB enable machine.
TECHNICAL SUPPORT
For technical support, please visit our website at www.memorex.com
or call (310) 891-1680. To return the Memorex product, please consult
the retailer where you purchased the product. To exchange the product with Memorex, you must call technical support to receive a RMA
Number before sending it back.
LIMITED 1-YEAR WARRANTY
Memtek Products warranties this product against defects in materials or workmanship for one year from the date of purchase. This
w a rranty applies to the original purc h a s e r, proof of original re t a i l
p u rchase is re q u i red. This warranty specifically excludes damage
caused by misuse, abuse, improper storage, or use in a commerc i a l
application. No warranty of merchantability or fitness for a part i cular purpose is made. In the event of a claim against this warr a n t y,
Memtek Products’ obligation, and the claimant’s sole re m e d y, shall
be replacement of the product. This warranty specifically excludes
responsibility for re c o rded data in any form .
USER GUIDE
FORMATTING YOUR FLASH MEMORY CARD
Most cards are pre-formatted. If formatting is necessary, it is
recommended to use your digital camera or Flash devices
to format the card. To format your Flash Memory Card in the
USB SD/MMC Card Reader, please use the following steps:
1 . Double click on “MY COMPUTER” i c o n .
2 . Place your mouse over “Me m o re x®USB SD/MMC Dual
R e a d e r” icon and R I G H Tc l i c k .
3 . Choose “F O R M AT ”and the following box will appear.
4 . F rom the dialogue box, select “Qu i c k(e r a s e) ” and then
p ress “S TA RT ” .
After formatting, the card will be ready to use.
My Computer
5395 4996
USER GUIDE
INSTALLATION
1. Tu rn on your computer, and wait for the Wi n d o w s®e n v i ronment
to appear on your scre e n .
2. Close any application you may have running before installing the
M e m o re x®USB SD/MMC Card Reader software driver.
3. Important! Please install driver software prior to plugging-in
the USB connector.
4. I n s e rt CD into CD-ROM Drive.
5. The setup program should automatically start. If it does not,
please run the setup program by following Step #6.
6. Click S t a rt on the task bar, then select "R u n" command. Type
D:\setup.exe (or CD-ROM drive letter:\setup.exe) and then
click "O K" .
7. Follow instructions during setup pro g r a m .
8. When finished, remove CD from CD-ROM drive, and re s t a rt
your PC.
9. Plug in the USB connector from the Card Reader into the USB
p o rt of your PC.
10. Windows will automatically detect the Memore x®USB SD/MMC
C a rd Reader and finish loading the driver for it.
1 . S t a rt Windows OS.
2 . Double click on “MY COMPUTER”.
3. You will now see a “Memorex®SD/MMC Dual
Reader” icon, that appears as a Removable
Flash hard disk. Depending on the configuration of your computer, the drive letter
assigned to your card reader will vary.
4 . Double click on the “Memore x®” icon.
5 . You may now copy files from your Card Reader
to your hard disk as you would from a floppy
disk or any other removable media by “dragging
& dropping” files.
Notes:
When a Flash Memory Card is
i n s e rted into the Card Reader, it
is configured as if it were a re m o vable hard disk drive. You use the
same methods to read and write
files as you would for your disk
d r i v e .
C A U T I O N :
As with any removable storage
media, removing the Flash Memory
C a rd while data is being
w r i t t e n / t r a n s f e rred may erase the
e n t i re content of the card. Always
wait for the data write operation to
complete before removing the
Flash Memory Card .
COPYING FILES
Loading...