HOME AUDIO SYSTEM WITH CD
PLAYER AND AM/FM STEREO RADIO
MODEL: MX4302
BEFORE OPERATING THIS PRODUCT, PLEASE READ THESE
INSTRUCTIONS COMPLETELY.
OPERATING INSTRUCTIONS
MX4302.O/M.QXD 3/4/03 7:47 AM Page 21
1
WARNING
CAUTION: TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER (OR BACK). NO
USER-SERVICEABLE PARTS INSIDE. REFER
SERVICING TO QUALIFIED SERVICE PERSONNEL.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
DANGEROUS VOLTAGE:
The lightning flash with arrowhead symbol,
within an equilateral triangle is intended to alert
the user to the presence of uninsulated
dangerous voltage within the product’s
enclosure that may be of sufficient magnitude to
constitute a risk of electric shock to persons.
ATTENTION:
The exclamation point within an equilateral
triangle is intended to alert the user to the
presence of important operating and
maintenance (servicing) instructions in the
literature accompanying the appliance.
DANGER:
Invisible and hazardous laser radiation when
open and interlock failed or defeated. Avoid
direct exposure to beam.
FCC WARNING:
This equipment may generate or use radio
frequency energy. Changes or modifications to
this equipment may cause harmful interference
unless the modifications are expressly
approved in the instruction manual. The user
could lose the authority to operate this
equipment if an unauthorized change or
modification is made.
SURGE PROTECTORS:
It is recommended to use a surge protector for
AC connection. Lightning and power surges
ARE NOT covered under warranty for this
product.
LASER SAFETY: This unit employs a laser. Only
qualified service personnel should attempt to
service this device due to possible eye injury.
CAUTION: USE OF CONTROLS,
ADJUSTMENTS OR PERFORMANCE
PROCEDURE HEREIN MAY RESULT IN
HAZARDOUS RADIATION EXPOSURE.
INFORMATION:
This equipment has been tested and found to
comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable
protection against harmful interference in a
residential installation. This equipment generates,
uses, and can radiate radio frequency energy
and, if not installed and used in accordance with
the instructions, may cause harmful interference
to radio communications. However, there is no
guarantee that interference will not occur in a
particular installation. If this equipment does
cause harmful interference to radio or television
reception, which can be determined by turning
the equipment off and on, the user is encouraged
to try to correct the interference by one or more
of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment
and receiver.
• Connect the equipment into an outlet on a
circuit different from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV
technician for help.
Thank you for purchasing the Memorex audio system.
The serial number of your unit can be found on a label on the bottom of the cabinet. We suggest that you
record the serial number in the space provided below in case this information is ever needed at a future
date.
PLEASE KEEP ALL PACKAGING MATERIAL FOR AT LEAST 90 DAYS IN CASE YOU NEED TO
RETURN THIS PRODUCT TO YOUR PLACE OF PURCHASE OR MEMOREX.
Model Number: MX4302
Serial Number: _______________________________________
MX4302.O/M.QXD 3/4/03 7:47 AM Page 1
2
Before using the unit, be sure to read all operating instructions
carefully. Please note that these are general precautions and may not
pertain to your unit. For example, this unit may not have the capability
to be connected to an outdoor antenna.
1. READ INSTRUCTIONS
All the safety and operating instructions should be read before the
product is operated.
2. RETAIN INSTRUCTIONS
The safety and operating instructions should be retained for future reference.
3. HEED WARNINGS
All warnings on the product and in the operating instructions should be
adhered to.
4. FOLLOW INSTRUCTIONS
All operating and use instructions should be followed.
5. CLEANING
Unplug this product from the wall outlet before cleaning. Do not use
liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.
6. ATTACHMENTS
Do not use attachments not recommended by the product's
manufacturer as they may cause hazards.
7. WATER AND MOISTURE
Do not use this product near water- for example, near a bathtub,
washbowl, kitchen sink, or laundry tub, in a wet basement, or near a
swimming pool.
8. ACCESSORIES
Do not place this product on an unstable cart, stand, tripod, bracket, or
table. The product may fall, causing serious injury and serious damage to
the product. Use only with a cart, stand, tripod, bracket, or table
recommended by the manufacturer or sold with the
product. Any mounting of the product should follow the
manufacturer’s instructions, and should use a mounting
accessory recommended by the manufacturer.
8A. An appliance and cart combination should be moved
with care. Quick stops, excessive force, and uneven
surfaces may cause the appliance and cart
combination to overturn.
9. VENTILATION
Slots and openings in the cabinet and in the back or bottom are
provided for ventilation and to ensure reliable operation of the product
and to protect it from overheating. These openings must not be blocked
or covered. The openings should never be blocked by placing the
product on a bed, sofa, rug, or other similar surface. This product
should never be placed near or over a radiator or heat source. This
product should not be placed in a built-in installation such as a
bookcase or rack unless proper ventilation is provided or the
manufacturer's instructions have been adhered to.
10. POWER SOURCES
This product should be operated only from the type of power source
indicated on the marking label. If you are not sure of the type of power
supply to your home, consult your appliance dealer or local power
company. For products intended to operate from battery power, or
other sources, refer to the operating instructions.
11. GROUNDING OR POLARIZATION
This product is equipped with a polarized alternating-current line plug
(a plug having one blade wider than the other). This plug will fit into the
power outlet only one way. This is a safety feature. If you are unable to
insert the plug fully into the outlet, try reversing the plug. If the plug
should still fail to fit, contact your electrician to replace your obsolete
outlet. Do not defeat the safety purpose of the polarized plug.
12. POWER-CORD PROTECTION
Power-supply cords should be routed so that they are not likely to be
walked on or pinched by items placed upon or against them, paying
particular attention to cords at plugs, convenience receptacles, and the
point where they exit from the appliance.
13. LIGHTNING
To protect your product from a lightning storm, or when it is left
unattended and unused for long periods of time, unplug it from the wall
outlet and disconnect the antenna or cable system. This will prevent
damage to the product due to lightning and power-line surges.
14. POWER LINES
An outside antenna system should not be located in the vicinity of
overhead power lines or other electric light or power circuits, or where it
can fall into such power lines or circuits. When installing an outside
antenna system, extreme care should be taken to keep from touching
such power lines or circuits as contact with them might be fatal.
15. OVERLOADING
Do not overload wall outlets and extension cords as this can result in a
risk of fire or electric shock.
16. OBJECT AND LIQUID ENTRY
Never push objects of any kind into this product through openings as they
may touch dangerous voltage points or short out parts that could result in
fire or electric shock. Never spill or spray any type of liquid on the product.
17. OUTDOOR ANTENNA GROUNDING
If an outside antenna is connected to the product, be sure the antenna
system is grounded so as to provide some protection against voltage
surges and built-up static charges. Section 810 of the National Electric
Code, ANSI/NFPA 70, provides information with respect to proper
grounding of the mast and supporting structure, grounding of the leadin wire to an antenna discharge product, size of grounding conductors,
location of antenna discharge product, connection to grounding
electrodes, and requirements for grounding electrode.
18. SERVICING
Do not attempt to service this product yourself as opening or removing
covers may expose you to dangerous voltage or other hazards. Refer
all servicing to qualified service personnel.
19. REPLACEMENT PARTS
When replacement parts are required, be sure the service technician
uses replacement parts specified by the manufacturer or those that
have the same characteristics as the original part. Unauthorized
substitutions may result in fire, electric shock or other hazards.
20. SAFETY CHECK
Upon completion of any service or repairs to this product, ask the
service technician to perform safety checks to determine that the
product is in proper operating condition.
21. WALL OR CEILING MOUNTING
The product should be mounted to a wall or ceiling only as
recommended by the manufacturer.
22. DAMAGE REQUIRING SERVICE
Unplug the product from the wall outlet and refer servicing to qualified
service personnel under the following conditions:
a. When the power-supply cord or plug is damaged.
b. If liquid has been spilled, or objects have fallen into the product.
c. If the product has been exposed to rain or water.
d. If the product does not operate normally by following the operating
instructions. Adjust only those controls that are covered by the
operating instructions, as an adjustment of other controls may result
in damage and will often require extensive work by a qualified
technician to restore the product to its normal operation.
e. If the product has been dropped or the cabinet has been damaged.
f. When the product exhibits a distinct change in performance - this
indicates a need for service.
23. HEAT
The product should be situated away from heat sources such as
radiators, heat registers, stoves, or other products (including amplifiers)
that produce heat.
24. NOTE TO CATV SYSTEM INSTALLER
This reminder is provided to call the CATV system installer's attention
to Article 820-40 of the NEC that provides guidelines for proper
grounding and, in particular, specifies that the cable ground shall be
connected to the grounding system of the building, as close to the point
of cable entry as practical.
EXAMPLE OF ANTENNA GROUNDING AS PER
NATIONAL ELECTRICAL CODE
IMPORTANT SERVICE SAFETY INSTRUCTIONS
MX4302.O/M.QXD 3/4/03 7:47 AM Page 2
PORTABLE CART WARNING
(symbol provided by RETAC)
3
PREPARATION FOR USE
AC OPERATION
Unwind the AC cord and extend it to its full length. Insert the small end of the AC cord into the AC power
jack on the rear of the unit. Insert the other end of the AC cord into any convenient 120V 60Hz household
outlet.
Please note that this unit is equipped with a polarized AC
plug which has one blade wider than the other. This is a
safety feature to reduce the likelihood of electric shock. This
polarized AC plug will only fit in a polarized AC outlet. If you
find that you cannot insert this plug into your outlet, you
may have an obsolete non-polarized outlet. Please do not
try to defeat this safety feature by using a non-polarized
adapter or by filing the wider blade to make it fit into your
outlet. If this plug does not fit into your outlet, you should contact a qualified licensed electrician to replace
your obsolete outlet.
SPEAKER CONNECTION
1. Place the speakers in convenient locations on either side of the unit.
Usually a distance of five to eight feet between speakers provides
the best stereo effect, but this may vary depending on the size and
acoustics of the room.
2. Locate the Speaker Terminals on the rear of the unit and connect the
red wires to the red (+) terminals and connect the black wires to the
black (–) terminals.
3. To connect the speakers, press the terminal down, insert the speaker wire and press the terminal back to
the lock position.
CAUTION: Only connect the speakers which are supplied with the unit. The use of any other or additional
speakers may cause damage to the unit. Never operate the unit without the speakers connected.
HEADPHONES
To listen to the unit through headphones, simply insert the headphones (not included) into the Headphones
jack. The speakers will be disconnected when the headphones are plugged in.
MX4302.O/M.QXD 3/4/03 7:47 AM Page 3
AC Plug
Red
AC Outlet
UNIT
Black
R
L
4
PREPARATION FOR USE (CONTINUED)
BATTERY OPERATION
The battery compartment is located on the rear of the remote control.
• Remove the battery compartment door by pressing down and sliding the door in
the direction of the arrow.
• Insert two (2) AA size batteries into the battery compartment as shown to the right.
Be sure to observe the polarity markings which are engraved inside the battery
compartment. If the batteries are inserted incorrectly, the remote control will not
operate.
• Replace the battery compartment door.
REMOTE SENSOR:
To operate the unit with the remote control, point the remote at the remote sensor on the front of the main
unit and press the appropriate button. The remote control has an effective operating range of approximately
15 feet and an angle of no more than 30°.
NOTE: Bright sunlight may interfere with the operation of the remote control.
BATTERY PRECAUTIONS
Follow these precautions when using batteries in this device:
1. Use only the size and type of batteries specified.
2. Be sure to follow the correct polarity when installing the batteries as indicated in the battery
compartment. Reversed batteries may cause damage to the device.
3. Do not mix different types of batteries together (e.g. Alkaline and Carbon-zinc) or old batteries with fresh
ones.
4. If the device is not to be used for a long period of time, remove the batteries to prevent damage or injury
from possible battery leakage.
5. Do not try to recharge batteries not intended to be recharged; they can overheat and rupture.
(Follow battery manufacturer’s directions.)
MX4302.O/M.QXD 3/4/03 7:47 AM Page 4
+
—
—
+
5
LOCATION OF CONTROLS AND INDICATORS
1. Display
2. Speaker Terminals (Rear of Unit)
3. POWER Button and Remote Sensor
4. STOP(■)/BAND Button
5. TUNING/CD Skip/Search Button
6. PLAY/PAUSE ( ) Button
7. TUNING/CD Skip/Search Button
8. REPEAT/MEMORY UP Button
9. FM Wire Antenna (Rear of Unit)
10. HOLD SET Button
11. CD Function Button
12. TUNER Function Button
13. MEMORY/CLOCK SET Button
14. CD Compartment
15. AC Power jack (Rear of Unit)
16. VOLUME Up Button
17. VOLUME Down Button
18. COLOR MODE Button
19. PRESET EQ Button
20. CD Door OPEN/CLOSE Button
21. TIMER/Sleep Button
22. Headphones Jack
MX4302.O/M.QXD 3/4/03 7:47 AM Page 5
1
2
3
4
5
6
7
8
9
10 18
11
12
13
14
15
16
17
19
20
21
22
6
LOCATION OF CONTROLS AND INDICATORS
1. FUNCTION Button
2. Direct Track Selection Buttons
3. OVER Button
4. PLAY/PAUSE Button
5. STOP/BAND Button
6. TUNING DN/UP Buttons
7. RANDOM Button
8. DISPLAY Button
9. INTRO Button
10. REP (Repeat)/MEM (Memory Up)
Button
11. SNOOZE Button
12. TIMER Button
13. POWER Button
14. MUTE Button
15. VOLUME +/– Buttons
16. PRESET EQ Button
17. MEM (Memory)/CLOCK Button
18. SLEEP Button
REMOTE
MX4302.O/M.QXD 3/4/03 7:47 AM Page 6
113
2
10
11
12
3
4
5
6
7
8
9
14
15
16
17
18
SETTING THE CLOCK
7
OPERATING INSTRUCTIONS
With the power off, press and
hold the MEMORY/CLOCK SET
button; “24H” will blink.
1
Press the MEMORY/CLOCK SET
button and the hours will blink.
3
Press the TUNING/CD Skip/
Search ❶ or ❷ button to
set the unit to the 24 hour (24H)
mode (also known as military
time), or 12 hour (12H) mode.
2
Press the TUNING/CD Skip/
Search ❶ or ❷ button to
set the current hour, then press
the MEMORY/CLOCK SET
button ❸ again; the minute digits
will blink. If you selected 12H time
display be sure to observe the AM
or PM indicators to make sure
you have set the hour correctly.
4
Press the TUNING/CD Skip/
Search ❶ or ❷ button to
set the current minute. Press the
MEMORY/CLOCK SET button ❸
and the time will be set.
5
MX4302.O/M.QXD 3/4/03 7:47 AM Page 7
2
1
2
1
3
2
1
3
8
OPERATING INSTRUCTIONS (CONTINUED)
Press and hold the COLOR MODE
button until RHYTHM appears in the
display, then release. The display
color will then change according to
the rhythm of the music. Press and
hold the COLOR MODE button
again until RHYTHM disappears
from the display to cancel Rhythm.
2
To leave one solid color in the
display, press the HOLD SET
button; HOLD will appear in the
display. Press the HOLD SET
button again to continue the color
cycling.
3
When the unit is on, press and
release the COLOR MODE button
to cycle through the 14 color
options. Each option will display a
different color sequence in the
display.
1
COLOR BUTTONS
When the unit is on, the display will cycle through the colors of the selected Color options - experiment for
your favorite color sequence! Change the color selection, or hold a particular color as follows:
Standby (Power Off) Mode
In Standby (Power Off) mode the display shows the correct time. Press the
DISPLAY button once to show the TIMER ON time. After five seconds the
display returns to the correct time.
Tuner Mode
In Tuner mode the display shows a radio frequency. Press the DISPLAY button
once to show the correct time, or twice to show the TIMER ON time. After five
seconds the display returns to show the radio frequency.
CD Mode
During CD playback, the display shows the CD track number and elapsed time.
Press the DISPLAY button once to see the Remaining Time on the disc, twice
to see the correct time, and a third time to see the TIMER ON time. After five
seconds the display returns to show the CD track number and elapsed time.
1
DISPLAY BUTTON (REMOTE CONTROL ONLY)
With the power on, press the PRESET EQ button to cycle through the
preset EQ settings, or to turn the EQ off. Each press of the PRESET
EQ button will cycle as follows: CLASSIC (harp), ROCK (guitar) POP
(dancing), Off.
1
PRESET EQ
MUTE
To temporarily mute the sound, press the MUTE button on the
remote control; the Mute indicator will appear in the display and the
sound will be muted. Press the MUTE button again to restore the
sound and the Mute indicator will disappear from the display.
1
MX4302.O/M.QXD 3/4/03 7:47 AM Page 8
9
OPERATING INSTRUCTIONS (CONTINUED)
Press the POWER button to turn
the unit on.
1
Press the TUNING/CD Skip/
Search ❶ or ❷ button to
select a station (see Tuning note
below).
NOTE: If the FM band is selected
and you have tuned to an FM
Stereo station, the FM Stereo
indicator will light in the display.
4
Press the STOP (■)/BAND
button to select AM or FM.
NOTE: If you select the FM band,
be sure to extend the FM Wire
Antenna.
3
Press the TUNER Function
button; the RADIO indicator will
appear in the display.
2
Adjust the PRESET EQ ❶ and
VOLUME ❷ buttons as desired.
5
When you have finished listening,
press the POWER button to turn
the unit off.
6
Hints for Better Reception
FM - Make sure that the FM Wire Antenna is extended to its full length. You may have to vary the direction
of the antenna to find the strongest signal for each FM station.
AM - The AM ferrite bar antenna is located inside the unit. It may be necessary to turn the unit slightly so
that the internal antenna is pointing in the direction of the AM transmitter. You may have to experiment to
find the position that provides the strongest reception for each of your favorite AM stations.
LISTENING TO THE RADIO
TUNING:
MANUAL TUNING: Repeatedly press the TUNING/CD Skip/Search or to manually advance the
frequency in the display up or down until the desired frequency appears.
AUTOMATIC TUNING: Press and hold the TUNING/CD Skip/Search or until the frequency in the
display starts to scan, and then release the button; the tuner will search and then stop on the next strong
station it finds. Repeat this procedure until the desired frequency appears in the display.
MX4302.O/M.QXD 3/4/03 7:47 AM Page 9
2
1
2
1
2
10
OPERATING INSTRUCTIONS (CONTINUED)
Press the POWER button to turn
the unit on.
1
Press the MEMORY/CLOCK SET
button ❶. Within four seconds,
press the REPEAT/MEMORY UP
button ❷ repeatedly until the
desired memory number appears
on the display.
4
Use the TUNING/CD Skip/Search
❶ or ❷ button to select a
station.
3
Press the TUNER Function button
❶; the RADIO indicator will
appear in the display.
Press the STOP (■)/BAND
button ❷ to select the desired
band - FM or AM.
2
Press the MEMORY/CLOCK SET
button again to set the station in
the selected memory.
5
Repeat steps 3 through 5 to
program up to 10 stations in each
band, if desired.
In case the main power supply
is interrupted, the memory
presets will be erased.
6
SETTING RADIO PRESETS
This unit can preset 10 AM and 10 FM radio stations for convenient recall.
Follow steps 1 and 2 above.
1
Adjust the PRESET EQ ❶ and
VOLUME ❷ buttons as desired.
3
Press the REPEAT/MEMORY UP
button to select a preset; the
station will automatically be tuned
in.
2
RECALLING RADIO PRESETS
MX4302.O/M.QXD 3/4/03 7:47 AM Page 10
2
1
2
1
2
1
12
35
2
1
2
11
Press the POWER button to turn
the unit on.
1
The CD player will read the table
of contents on the disc and the
total number of tracks and total
playing time on the disc will
appear in the display.
4
Press the CD OPEN/CLOSE
button to open the CD
Compartment and insert a CD with
the label side facing up. Press
again to shut the CD
Compartment.
3
Press the CD Function button to
select CD.
2
Press the PLAY/PAUSE ( )
button to begin playback on
Track 1.
5
Adjust the PRESET EQ ❶ and
VOLUME ❷ buttons as
desired. Playback will continue
until all the tracks on the disc
have been played.
6
To stop playback before the disc
ends, press the STOP (■)/BAND
button. The disc will stop and the
display will show the total number
of tracks and playing time on the
disc.
7
After the last track has been
played, the disc stops automatically and the display shows the
total number of tracks and playing
time on the disc. If you are finished
listening, press the CD OPEN/
CLOSE button to eject the CD
Compartment.
8
Remove your disc, press the CD
Door OPEN/CLOSE button ❶ to
close the CD door and press the
POWER button ❷ to turn the unit
off.
9
PLAYING COMPACT DISCS
NORMAL PLAYBACK
OPERATING INSTRUCTIONS (CONTINUED)
MX4302.O/M.QXD 3/4/03 7:47 AM Page 11
CD
2
1
2
2
1
12
After you insert the disc into the CD
player and the total number of
tracks and playing time appear on
the display, you may press either
the CD Skip/Search ❶ or
❷ button to select a specific track
for playback.
1
When the desired track number
appears in the display, press the
PLAY/PAUSE ( ) button.
Playback will begin on the track
you selected.
2
During CD playback, if you wish
to pause the disc momentarily,
press the PLAY/PAUSE ( )
button again. Playback stops but
the disc continues to spin and the
time display will blink.
1
Press the PLAY/PAUSE ( )
button again to release pause and
resume normal CD playback.
2
CD PAUSE CONTROL
TO BEGIN PLAYBACK FROM A SPECIFIC TRACK
During playback, depress and
hold either the CD Skip/Search
()or ( ) button to move the
player forward or backward within
a track to locate a specific
musical passage. The player will
move forward or backward at high
speed as long as the button is
depressed. When you release the
CD Skip/Search ( ) or ( )
button, normal playback will
resume.
During playback, press the CD
Skip/Search ( ) button once to
advance the player to the
beginning of the next track. Press
the CD Skip/Search ( ) button
repeatedly to advance the player
to higher numbered tracks.
1 3
During playback, press the CD
Skip/Search ( ) button once to
move the player back to the
beginning of the current track. Press
the CD Skip/Search ( ) button
repeatedly to move the player back
to lower numbered tracks.
2
FORWARD/REVERSE SKIP TRACK AND HIGH-SPEED MUSIC SEARCH ( / )
OPERATING INSTRUCTIONS (CONTINUED)
If the track is over 10, press the
OVER button repeatedly to select
the tenth digit of the track number
(i.e. to select track 24, press the
OVER button twice {"2-" will
appear}, then press the 4 button).
Playback will automatically start.
3
MX4302.O/M.QXD 3/4/03 7:47 AM Page 12
2
1
1
2
13
To repeat a single track, while in
the Stop mode, press the
REPEAT/MEMORY UP button ❶
once; “REPEAT” will blink in the
display. Press the CD Skip/Search
❷ or button ❸ to select
the specific track that you wish to
repeat. When the desired track
number appears in the display,
press the PLAY/PAUSE ( )
button ❹ to begin playback. The
specific track you selected will be
repeated continuously. You can
press the REPEAT/MEMORY UP
button ❶ while a track is playing to
repeat that track.
1
To cancel Repeat Playback,
press the REPEAT/MEMORY UP
button ❶ until “REPEAT” dis-
appears from the display. You
can also cancel Repeat Playback
by pressing the CD OPEN/
CLOSE button ❷.
3
To repeat all of the tracks on a
disc continuously, while in the
Stop mode, press the
REPEAT/MEMORY UP button ❶
twice; “REPEAT” will light in the
display. Press the CD
PLAY/PAUSE ( ) button ❷ to
begin all tracks repeating.
2
REPEAT PLAYBACK
Press the CD Function button to
select CD.
1
Press the MEMORY/CLOCK SET
button; “P-01” (program number),
“01” (track number) will appear
and “MEMORY” will appear in the
display.
3
Insert a CD with the label side
facing up.
Wait for the CD player to read the
table of contents and display the
total number of tracks and playing
time of the disc.
2
PROGRAMMED PLAYBACK
The CD player in this unit has a 20 track programmable memory that allows you to program up to 20 tracks
on any disc for playback in any desired order. You may program 20 different tracks or you may also program
certain tracks to play more than once.
To perform programmed playback, proceed as follows:
PROGRAMMED PLAYBACK SECTION CONTINUED ON NEXT PAGE.
OPERATING INSTRUCTIONS (CONTINUED)
MX4302.O/M.QXD 3/4/03 7:47 AM Page 13
3
4
2
1
1
2
1
2
CD
14
Press the CD Skip/Search ❶
or button ❷ to select the first
track that you wish to program.
When the desired track number
appears in the display, press the
MEMORY/CLOCK SET button ❸
again.
4
Press either the CD Skip/Search
() ❶ or ( ) button ❷ to select
the next track you wish to
program.
When the desired track
number
appears in the display,
press the MEMORY/CLOCK SET
button ❸ again.
5
Repeat step 5 until you have
programmed up to 20 track
numbers into the CD Program
Memory.
6
After programming up to 20 tracks in the CD Program Memory, press the
PLAY/PAUSE ( ) button ❶ to begin programmed playback.
“MEMORY” will appear in the display and playback will begin on the first
track that you programmed. The player will continue to play all of the
tracks that you programmed in the order in which you programmed them.
When the last programmed track has been played, the player will stop and
the display will again show the total number of tracks and playing time on
the disc. If you press the MEMORY/CLOCK SET button ❷ and then press
the PLAY/PAUSE ( ) button ❶ again, playback will start on the first
track you programmed and will continue until all the programmed tracks
have been played. To cancel the Programmed Playback mode, press the
MEMORY/CLOCK SET button ❷ while in the Stop mode to enter the
program mode, and then press the STOP (■)/BAND button ❸twice.
7
It is also possible to use the Program
and Repeat functions together to
repeat a specific program indefinitely.
First, program the tracks you wish to
hear in the order you wish to hear
them, as described above. Then,
press the REPEAT/MEMORY UP
button twice. Both the MEMORY and
REPEAT indicators will appear in the
display.
1
Press the PLAY/PAUSE ( )
button to begin programmed
repeat playback. The player will
play the tracks you selected in the
order in which you programmed
them. When the last track in the
program has been played, the
entire program will begin again.
2
Programmed Repeat operation
will continue indefinitely until you
press the STOP (■)/BAND
button.
3
PROGRAMMED REPEAT
OPERATING INSTRUCTIONS (CONTINUED)
NOTE: If no button is pressed within five seconds, the unit will revert back to the total time/tracks on the CD.
MX4302.O/M.QXD 3/4/03 7:47 AM Page 14
2
1
3
1
3
2
2
1
3
2
1
3
15
To play the first 10 seconds of
each track on the CD, press the
INTRO button. Playback will start
automatically and will play 10
seconds of each track.
1
To cancel intro playback, press
the INTRO button until “INTRO”
disappears from the display;
playback will continue from that
point.
2
INTRO PLAYBACK
OPERATING INSTRUCTIONS (CONTINUED)
To play the tracks on the CD in a
random order, while in the Stop
mode, press the RANDOM
button. Playback will start
automatically and all the tracks
will play in a random order.
1
To cancel random playback,
press the RANDOM button until
“RANDOM” disappears from the
display.
2
RANDOM PLAYBACK
MX4302.O/M.QXD 3/4/03 7:47 AM Page 15
16
With the power off, press and
hold the TIMER/Sleep button ❶;
“TIMER” will blink in the display.
Within three seconds, press and
hold the MEMORY/CLOCK SET
button ❷ until the Timer Hour
blinks in the display.
1
Within a few seconds, “TIMER” will
light in the display to indicate that
the timer is set. When the actual
time matches the time set for the
Timer, the unit will turn on to the
last function (CD or tuner) used. It
will play for one hour (in the Tuner
mode) or to the end of the disc (in
the CD mode) and then shut off and
reset itself for the following day.
Press the POWER button to turn off
the timer and set it for the next day.
TO TURN THE TIMER OFF SO IT
IS NOT SET FOR THE NEXT DAY,
press and hold the TIMER/Sleep
button again until “TIMER”
disappears from the display.
3
Press the CD
Skip/Search ❶
or ❷ button to set the hour,
then press the MEMORY/CLOCK
SET button ❸ again; the minute
digits will blink. Press the
CD
Skip/Search ❶ or ❷
button to set the minutes, then
press the MEMORY/CLOCK SET
button ❸ again.
2
SETTING THE TIMER
Set the timer to turn the unit on to the Tuner or CD mode at a preset time as follows :
NOTE: Please make sure the volume is set to the desired level to wake you up.
OPERATING INSTRUCTIONS (CONTINUED)
Press the POWER button to turn
the unit on and tune the desired
radio station or insert a CD as
previously instructed.
1
Press the TIMER/Sleep button a
second time to set the unit to turn off
after 80 minutes. Each additional
press with decrease the sleep time by
10 minutes. Five seconds after the
sleep time is set (“SLEEP” will light in
the display), you can press the
TIMER/Sleep button at any time to
stop the Sleep function; “SLEEP” will
disappear from the display.
3
Press the TIMER/Sleep button
and “90” will appear and “SLEEP”
will blink in the display.
2
ACTIVATING THE SLEEP FUNCTION
Set the sleep timer as follows:
SNOOZE
The timer can be temporarily turned off manually by pressing the SNOOZE button on the remote; the
timer will turn back on automatically nine minutes later.
MX4302.O/M.QXD 3/4/03 7:47 AM Page 16
2
1
2
3
1
Caring for Compact Discs
• Treat the compact disc carefully. Handle the compact disc
only by its edges. Never allow your fingers to come in contact
with the shiny, unprinted side of the compact disc.
• Do not attach adhesive tape, stickers, etc. to the compact
disc label.
• Clean the compact disc periodically with a soft, lint-free, dry
cloth. Never use detergents or abrasive cleaners to clean
the compact disc. If necessary, use a CD cleaning kit.
• If a compact disc skips or gets stuck on a section of the compact disc, it is probably dirty or damaged (scratched).
• When cleaning the compact disc, wipe in straight lines from the center of the compact disc to the outer
edge of the compact disc. Never wipe in circular motions.
• This unit is designed to play only compact discs bearing the identification logo as shown here.
Other compact discs may not conform to the CD standard and may not play properly.
• Compact discs should be stored in their cases after each use to avoid damage.
• Do not expose compact discs to direct sunlight, high humidity, high temperatures, or dust, etc. Prolonged
exposure or extreme temperatures can warp the compact disc.
• Do not stick or write anything on either side of the compact disc. Sharp writing instruments, or the ink may
damage the surface.
17
CARE AND MAINTENANCE
MX4302.O/M.QXD 3/4/03 7:47 AM Page 17
C
L
R
E
E
A
B
E
E
N
N
E
Z
N
18
Symptom Possible Cause Solution
Radio
Noise or sound distorted Station not tuned properly for Retune the AM or FM broadcast
on radio broadcasts. AM or FM. station.
FM: Wire Antenna is not Extend FM Wire Antenna.
extended.
AM: Unit is not positioned Rotate unit until best reception is
correctly. obtained.
FM STEREO indicator Poor FM signal being received. Retune station or try another station
does not light. that broadcasts in stereo.
Station is not broadcasting in stereo. Change stations.
AM or FM, no sound. TUNER Function button Press the TUNER Function button
is not pressed. to select Tuner.
Volume at minimum. Increase volume.
Compact Disc Player
CD Player will not play. CD function is not selected. Press the CD Function button to
select CD.
CD is not installed or installed Insert CD with label facing up.
incorrectly.
CD skips while playing. Disc is dirty or scratched. Wipe disc with cloth or use
another disc.
General
No power. AC power cord is not connected. Connect AC power cord.
Should this unit exhibit a problem, check the following before seeking service:
TROUBLESHOOTING GUIDE
MX4302.O/M.QXD 3/4/03 7:47 AM Page 18
19
FOR ADDITIONAL SET-UP OR OPERATING ASSISTANCE, PLEASE VISIT OUR WEBSITE AT
WWW.MEMOREXELECTRONICS.COM
OR CONTACT CUSTOMER SERVICE AT 1-800-919-3647.
PLEASE KEEP ALL PACKAGING MATERIAL FOR AT LEAST 90 DAYS IN CASE YOU NEED
TO RETURN THIS PRODUCT TO YOUR PLACE OF PURCHASE OR MEMOREX.
FOR PARTS AND ACCESSORIES, CONTACT FOX INTERNATIONAL AT 1-800-321-6993.
MX4302.O/M.QXD 3/4/03 7:47 AM Page 19
Memcorp, Inc.
Weston, FL
Printed in Hong Kong
Visit our website at www.memorexelectronics.com
MX4302.O/M.QXD 3/4/03 7:47 AM Page 20
Loading...