Memorex MVD4540C User Manual
OWNER’S MANUAL
MANUAL DE INSTRUCCIONES
DVD PLAYER / Hi-Fi VIDEO CASSETE RECORDER
DVD COMPACTOS / VIDEOGRABADOR Hi-Fi ESTEREO
MVD4540C
ENGLISH
ESPAÑOL
If you purchase a universal remote control from your local retailer, please contact the
remote manufacturer for the required programming code.
Si usted a comprado un control remoto universal, por favor comunicace con el fabricante
para el codico de programaccion requerido.
When shipped from the factory, the TV/CABLE menu option is set to the "CABLE"
(Cable Television) mode.
If not using CABLE (Cable TV), set this menu option to the "TV" mode.
Al salir la unidad de fábrica, la opción de menú de TV/CABLE se ajusta al modo de
"CABLE" (Televisión por cable).
Si no utiliza CABLE, ajuste esta opción de menú al modo de "TV".
Before operating the unit, please read this manual thoroughly.
Antes de usar la unidad, lea detenidadmente este manual de instrucciones.
2D81121AE Cover 6/4/04, 18:191
ATTENTION
ATENCION
TV/CABLE MODE SELECTION
SELECCION DE MODO DE TV/CABLE
ENGLISH
The lightning flash with arrowhead
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION:
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN
NOTE:
Please keep all packaging material for at least 90 days in case you need to return this product to your place of purchase or
Memorex.
TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER (OR
BACK). NO USER-SERVICEABLE PARTS
INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
OR MOISTURE.
symbol, within an equilateral triangle is
intended to alert the user to the presence
of uninsulated dangerous voltage within
the product's enclosure that may be of
sufficient magnitude to constitute a risk
of electric shock to persons.
The exclamation point within an equilateral
triangle is intended to alert the user to
the presence of important operating and
maintenance (servicing) instructions in
the literature accompanying the appliance.
WARNING: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
CAUTION: Changes or modifications not expressly approved by the partly responsible for compliance with the FCC
CAUTION:
THIS DIGITAL VIDEO PLAYER EMPLOYS A LASER SYSTEM.
TO ENSURE PROPER USE OF THIS PRODUCT, PLEASE READ THIS USER'S GUIDE CAREFULLY AND RETAIN FOR
FUTURE REFERENCE. SHOULD THE UNIT REQUIRE MAINTENANCE, CONTACT AN AUTHORIZED SERVICE LOCATION-SEE SERVICE PROCEDURE.
USE OF CONTROLS, ADJUSTMENTS OR THE PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED
HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.
TO PREVENT DIRECT EXPOSURE TO LASER BEAM, DO NOT TRY TO OPEN THE ENCLOSURE. VISIBLE LASER
RADIATION MAY BE PRESENT WHEN THE ENCLOSURE IS OPENED. DO NOT STARE INTO BEAM.
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference to
radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Rules could void the user's authority to operate this equipment.
Location of the required Marking
The rating sheet and the safety caution are on the rear of the unit.
CERTIFICATION: COMPLIES WITH FDA RADIATION PERFORMANCE
STANDARDS, 21 CFR SUBCHAPTER J.
2
2D81121A[E] (02-05) 6/4/04, 18:192
IMPORTANT SAFEGUARDS
1. READ INSTRUCTIONS
All the safety and operating instructions should be read before the unit is operated.
2. RETAIN INSTRUCTIONS
The safety and operating instructions should be retained for future reference.
3. HEED WARNINGS
All warnings on the unit and in the operating instructions should be adhered to.
4. FOLLOW INSTRUCTIONS
All operating and use instructions should be followed.
5. CLEANING
Unplug this unit from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners.
Use a damp cloth for cleaning the exterior cabinet only.
6. ATTACHMENTS
The manufacturer of this unit does not make any recommendations for attachments, as they may cause hazards.
7. WATER AND MOISTURE
Do not use this unit near water. For example, near a bathtub, washbowl, kitchen sink, laundry tub, in a wet basement, or
near a swimming pool.
8. ACCESSORIES
Do not place this unit on an unstable cart, stand, tripod, bracket, or table.
The unit may fall, causing serious injury, and serious damage to the unit.
8A. An appliance and cart combination should be moved with care. Quick stops,
excessive force, and uneven surfaces may cause the appliance and cart
combination to overturn.
9. VENTILATION
Slots and openings in the cabinet back or bottom are provided for ventilation,
to ensure reliable operation of the unit, and to protect it from overheating.
These openings must not be blocked or covered. The openings should never be blocked by placing the unit on a bed,
sofa, rug, or other similar surface. This unit should never be placed near or over a radiator or heat source. This unit
should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided and/or the
manufacturer’s instructions have been adhered to.
10. POWER SOURCES
This unit should be operated only from the type of power source indicated on the rating plate. If you are not sure of the
type of power supply to your home, consult your appliance dealer or local power company. For units intended to operate
from battery power, or other sources, refer to the operating instructions.
11. GROUNDING OR POLARIZATION
This unit is equipped with a polarized alternating-current line plug (a plug having one blade wider than the other). This
plug will fit into the power outlet only one way. This is a safety feature. If you are unable to insert the plug fully into the
outlet, try reversing the plug. If the plug should still fail to fit, contact your electrician to replace your obsolete outlet. Do
not defeat the safety purpose of the polarized plug, if your unit is equipped with a 3-wire grounding-type plug, a plug
having a third (grounding) pin. This plug will only fit into a grounding-type power outlet. This too, is a safety feature. If you
are unable to insert the plug into the outlet, contact your electrician to replace your obsolete outlet.Do not defeat the
safety purpose of the grounding-type plug.
12. POWER-CORD PROTECTION
Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or
against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from
the appliance.
13. LIGHTNING
To protect your unit from a lightning storm, or when it is left unattended and unused for long periods of time, unplug it
from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the unit due to lightning
and power line surges.
14. POWER LINES
An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power
circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care
should be taken to keep from touching such power lines or circuits, as contact with them might be fatal.
15. OVERLOADING
Do not overload wall outlets and extension cords, as this can result in a risk of fire or electric shock.
16. OBJECT AND LIQUID ENTRY
Do not push objects through any openings in this unit, as they may touch dangerous voltage points or short out parts that
could result in fire or electric shock. Never spill or spray any type of liquid into the unit.
17. OUTDOOR ANTENNA GROUNDING
If an outside antenna or cable system is connected to the unit, be sure the antenna or cable system is grounded to
provide some protection against voltage surges and built-up static charges, Section 810 of the National Electrical Code,
ANSI/NFPA 70, provides information with respect to proper grounding of the mast and supporting structure, grounding of
the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna discharge unit, connection to grounding electrodes, and requirements for the grounding electrode.
18. SERVICING
Do not attempt to service this unit yourself as opening or removing covers may expose you to dangerous voltage or other
hazards. Refer all servicing to qualified service personnel.
PORTABLE CART WARNING
(symbol provided by RETAC)
S3125A
ENGLISH
3
2D81121A[E] (02-05) 6/4/04, 18:193
IMPORTANT SAFEGUARDS
19. DAMAGE REQUIRING SERVICE
Unplug this unit from the wall outlet and refer servicing to qualified service personnel under the following
conditions:
a. When the power-supply cord or plug is damaged.
b. If liquid has been spilled, or objects have fallen into the unit.
c. If the unit has been exposed to rain or water.
d. If the unit does not operate normally by following the operating instructions. Adjust only those
controls that are covered by the operating instructions, as an improper adjustment of other controls may result in
damage and will often require extensive work by a qualified technician to restore the unit to its normal operation.
e. If the unit has been dropped or the cabinet has been damaged.
20. REPLACEMENT PARTS
21. SAFETY CHECK
22. HEAT
23. DISC TRAY
24. CONNECTING
25. LASER BEAM
26. DISC
27. NOTE TO CABLE TV SYSTEM INSTALLER
f. When the unit exhibits a distinct change in performance, this indicates a need for service.
When replacement parts are required, be sure the service technician uses replacement parts specified by the manufacturer or those that have the same characteristics as the original part.
Unauthorized substitutions may result in fire, electric shock or other hazards.
Upon completion of any service or repairs to this unit, ask the service technician to perform safety checks to determine
that the unit is in proper operating condition.
The product should be situated away from heat sources such as radiators, heat registers, stoves, or other products
(including amplifiers) that produce heat.
Keep your fingers well clear of the disc tray as it is closing. It may cause serious personal injury.
When you connect the product to other equipment, turn off the power and unplug all of the equipment from the wall
outlet. Failure to do so may cause an electric shock and serious personal injury. Read the owner's manual of the other
equipment carefully and follow the instructions when making any connections.
Do not look into the opening of the disc tray or ventilation opening of the product to see the source of the laser beam. It
may cause sight damage.
Do not use a cracked, deformed, or repaired disc. These discs are easily broken and may cause serious personal injury
and product malfunction.
This reminder is provided to call the CABLE TV system installer’s attention to Article 820-40 of the NEC that provides
guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding
system of the building, as close to the point of cable entry as practical.
EXAMPLE OF ANTENNA GROUNDING AS PER THE
GROUND CLAMP
ELECTRIC SERVICE
EQUIPMENT
NEC-NATIONAL ELECTRICAL CODE
S2898A
CONDENSATION
Moisture will form in the operating section of the DVD/VCR if the player is brought from cool surroundings into a warm room
or if the temperature of the room rises suddenly. When this happens, the DVD/VCR's performance will be impaired.
To prevent this, let the DVD/VCR stand in its new surroundings for about an hour before switching it on, or make sure that the
room temperature rises gradually.
Condensation may also form during the summer if the DVD/VCR is exposed to the breeze from an air conditioner. In such
cases, change the location of the DVD/VCR.
NATIONAL ELECTRICAL CODE
ANTENNA LEAD IN WIRE
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810-20)
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
GROUND CLAMPS
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250, PART H)
4
2D81121A[E] (02-05) 6/4/04, 18:194
Features
DVD/CD Player/Video Cassette Recorder
• DVD/CD player with Video Cassette Recorder - Unique space saving design combines a DVD/CD player and a Hi-Fi Video
cassette recorder. The DVD disc has much more capacity, but is the same size as the audio CD disc. Picture quality is higher than
Super VHS. Audio quality is higher than audio CD. The DVD PLAYER can play back audio CDs.
• High Quality Picture - More than 500 lines (VCR mode: 230 lines) of Horizontal Resolution. It exceeds Super VHS (400 lines)
or Laser Disc (430 lines) in resolution.
VCR Section
• Stereo/SAP Reception - This VCR is designed to receive stereo and second audio program (SAP) broadcasts where
available.
• 4 Video Heads - Provides optimal picture quality for special effects playback.
• 19µm HEAD - For superior picture quality even in SLP mode, 19micron width technology helps to avoid crosstalk and boost
SLP picture quality to near SP levels. With precision technology, ghosts and color beats are virtually eliminated.
• Hi-Fi Stereo Sound - With a frequency response of 20 to 20,000 Hz and a dynamic range of better than 90dB, this VCR
provides a level of excellence that rivals compact discs.
• One-touch Timer Recording (OTR) - Simply by pressing the REC/OTR button, the VCR can be programmed for up to 6
hours of recording with an immediate start.
DVD Section
• Compatible with a wide range of DVD audio outputs
Digital Audio Jack (Optical or Coaxial):
• When a component with a built-in Dolby Digital decoder is connected, Dolby Digital sound can produce the effect of being
in a movie theater or a concert hall.
• Surround standard different from Dolby Digital. This format is already in use in many theaters. By connecting this unit to a
DTS decoder or an AV amplifier with a built-in DTS decoder, the DTS audio of DVD discs recorded in this format can be
enjoyed. However, audio will not be output from the analog audio output jacks.
• The MPEG audio of DVD discs recorded in this format can be enjoyed.
• The Linear PCM sound of a 48 kHz/16 bit through 96 kHz/24 bit exceeds audio CD sound.
• Progressive scan - Progressive scan displays all the horizontal lines of a picture at one time, as a single frame. This unit
converts the interlaced (480i) video from DVD into progressive (480p) format for connection to a progressive display. It
increases the vertical resolution.
• Multi-Language - Since this DVD matches with 124 language-subtitles/-soundtracks, you can enjoy selecting a favorite
one. (You can not select the language that is not recorded on the disc.)
• Multi-Angle - Pictures of Sports or a Live Concert are recorded with many cameras. When you play such a disc, you can
change the angles during playback. (If a Multi-Angle is not recorded on the disc, you can not change the angle.)
• Repeat Playback - You can repeat chapter, track, title, sides or material between two selected points.
• Program/Random Playback (CD) - You can play back tracks in programmed or random-selected sequences.
• Zoom - You can zoom in on the selected subject on the screen during playback.
• Video Aspect Ratio - You can change the aspect ratio of the screen for your monitor/television on a suitable disc.
• Parental Control - You can limit the playback of scenes or sounds of adult DVD discs which have a parental level rating.
ENGLISH
This product incorporates copyright protection technology that is protected by method claims of certain U.S. patents and
*
other intellectual property rights owned by Macrovision Corporation and other rights owners. Use of this copyright protection technology must be authorized by Macrovision Corporation and is intended for home and other limited viewing uses
only unless otherwise authorized by Macrovision Corporation. Reverse engineering or disassembly is prohibited.
Consumers should note that not all high definition television sets are fully compatible with this product and may cause
artifacts to be displayed in the picture. In case of 525 progressive scan picture problems, it is recommended that the user
switch the connection to the “STANDARD DEFINITION” output. If there are questions regarding our TV set compatibility
with this model 525p DVD player, please contact our customer service center.
Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol are trademarks of Dolby Labora-
*
tories.
“DTS” and “DTS Digital Out” are trademarks of Digital Theater Systems, Inc.
*
Unauthorized recording of copyrighted television programs, films, video cassettes and other materials may infringe the
*
rights of copyright owners and be contrary to copyright laws.
2D81121A[E] (02-05) 6/4/04, 18:195
5
Contents
IMPORTANT SAFEGUARDS .................................. 3
Features ................................................................... 5
Contents ................................................................... 6
Parts and functions .................................................. 7
Remote control ......................................................... 8
Power source ........................................................... 9
Basic connections .................................................. 10
Antenna to DVD/VCR connection ..................... 10
DVD/VCR to TV connection .............................. 10
CABLE TV connections ......................................... 11
Playback connections ............................................ 12
Setting up the VCR section .................................... 14
Setting the video channel.................................. 14
Setting the language ......................................... 14
Auto clock setting .............................................. 15
Manual clock setting ......................................... 16
Tuner setting ..................................................... 16
To add/delete channels..................................... 16
Noise elimination............................................... 16
Tape playback operation ........................................ 17
Loading and Unloading a cassette tape............ 17
Cassette tape playback..................................... 17
Special playback ............................................... 17
ZERO RETURN function .................................. 18
Video index search system ............................... 18
Recording ............................................................... 19
Recording a TV program................................... 19
One-touch Timer Recording (OTR)................... 20
Timer recording ................................................. 20
Advanced function of VCR section ........................ 22
Stereo recording and playback ......................... 22
Second audio program (SAP) ........................... 22
Duplicating a video tape.................................... 22
Disc playback operation ......................................... 23
Disc ................................................................... 23
Setting setup language ..................................... 23
Playback procedure .......................................... 24
Special playback ............................................... 24
Zooming ............................................................ 24
Locating desired scene ..................................... 25
Marking desired scenes .................................... 25
Changing soundtrack language ........................ 25
Subtitles ............................................................ 25
Karaoke playback ............................................. 25
Changing angles ............................................... 26
Title selection .................................................... 26
DVD menu ........................................................ 26
Repeat playback ............................................... 26
Program playback (CD) .................................... 26
Random playback (CD)..................................... 27
MP3 playback ................................................... 27
Advanced function of DVD section ........................ 28
Parental control ................................................. 28
Temporary disabling of rating level by
DVD disc ........................................................... 28
Setting language ............................................... 29
Setting the aspect ratio of TV screen ................ 29
Setting on screen display .................................. 30
Status display of disc ........................................ 30
Dynamic Range Control .................................... 30
Progressive scan .............................................. 30
Language code list ................................................. 31
Problems and troubleshooting ............................... 32
Video head cleaning .............................................. 33
Specifications ......................................................... 34
6
2D81121A[E] (06-09) 6/4/04, 18:196
Parts and functions
Front
POWER CHANNEL
VIDEO IN L - AUDIO IN - R
POWER button
AUDIO (L/R)/
VIDEO IN jacks
Display window
VCR/DVD mode selector button
Cassette Loading Slot
EJECT button
VCR DVD
VCR/DVD
CHANNEL / buttons
VCR indicator
Play indicator
VCR indicator
Pause indicator
OPEN/CLOSE button
Remote sensor
Display window
REW (Rewind) button
PLAY button
STOP button
Disc tray
ENGLISH
DVD
VCR
DVD indicator
REC button
FF (Fast Forward) button
DVD indicator
REC indicator
TRK indicator
Video tape indicator
Number indicator (Title, Chapter, Track playing time or other information)
Progressive scanning indicator
Timer recording indicator
NOTE:
Some discs may be displayed wrong or e.g. chapter number, playback time, etc. may not be displayed.
Rear
DVD COAXIAL DIGITAL AUDIO OUT jack
DVD S-VIDEO OUT jack
AC power cord
DVD COMPONENT OUT jacks
S-VIDEO/COMPONENT Video selector switch
DVD/VCR common AUDIO (L/R)/VIDEO OUT jacks
DVD AUDIO (L/R) OUT jacks
RF OUT jack
DVD OPTICAL DIGITAL AUDIO OUT jack (dust protection cap)
CD indicator
PM indicator
RF IN jack
7
2D81121A[E] (06-09) 6/4/04, 18:197
Remote control
POWER [9]
EJECT [17]
0 – 9 [16]
SETUP [23]
VCR MENU [14]
CH / [9]
TRK/SET + / – [14]
Cursor Buttons [15]
DVD MENU [26]
STOP [17] [24]
SKIP [24]
INDEX + / – [18]
MARKER [25]
VCR/DVD [9]
OPEN/CLOSE [24]
TIMER REC [20]
INPUT SELECT [22]
PROGRESSIVE [30]
DISPLAY [15] [25]
RETURN [23]
TOP MENU [26]
ENTER [14]
CANCEL [21]
PLAY [17] [24]
PAUSE/STILL [18] [24]
SEARCH + / – [17] [24]
SLOW [18] [24]
AUDIO SELECT [22]
AUDIO [25]
REC/OTR [19]
ZOOM [24]
JUMP [25]
ZERO RETURN [18]
SUBTITLE [25]
ATR [18]
8
2D81121A[E] (06-09) 6/4/04, 18:198
CLOCK/COUNTER [18]
TV/VCR [14]
REPEAT A-B [26]
ANGLE [26]
COUNTER RESET [18]
PLAY MODE [26]
SPEED [19]
Inserting Batteries
Remote control / Power source
Open the battery
1
compartment cover in the
direction of the arrow.
Install two “AAA” batteries (not
23
supplied),
polarity diagram in the battery
compartment.
paying attention to the
Replace the compartment
cover.
Battery precautions
The precautions below should be followed when using batteries in this device:
1. Use only the size and type of batteries specified.
2. Be sure to follow the correct polarity when installing the batteries as indicated in the battery compartment.
batteries may cause damage to the device. To avoid a potential short circuit, insert the “–” end first.
3.
Do not mix different types of batteries together (e.g. Alkaline and Carbon-zinc) or old batteries with fresh ones.
4. If the device is not to be used for a long period of time, remove the batteries to prevent damage or injury from possible
battery leakage.
5. Do not try to recharge batteries not intended to be recharged; they can overheat and rupture. (Follow battery manufacturer’s directions.)
Reversed
Remote control basics
• Press POWER to turn the DVD/VCR on or off.
• Press CH or CH to move through the channels one channel at a time.
• The CH / and SET +/– are also used to navigate on-screen menu system.
• You can directly access specific channels using Number keys pad.
• Each press of VCR/DVD on the remote control, switches the screen between the VCR screen (VCR mode) and the DVD
screen (DVD mode).
ENGLISH
Operation
• Aim the remote control at the remote sensor and press control buttons to operate.
• Operate the remote control within 30° angle on either side of the remote sensor,
up to a distance of Approx. 5 meters.
AC Outlet
Wider Hole
and Blade
Polarized AC Cord Plug
(One blade is wider than the other.)
TO USE AC POWER SOURCE
Use the AC polarized line cord provided for operation on AC. Insert the AC
cord plug into a standard 120V 60Hz polarized AC outlet.
NOTES:
Never connect the AC line cord plug to other than the specified
•
voltage (120V 60Hz). Use the attached power cord only.
If the polarized AC cord does not fit into a non-polarized AC
•
outlet, do not attempt to file or cut the blade. It is the user’s
responsibility to have an electrician replace the obsolete outlet.
If you cause a static discharge when touching the unit and the
•
unit fails to function, simply unplug the unit from the AC outlet
and plug it back in. The unit should return to normal operation.
Approx. 5 meters
Power source
9
2D81121A[E] (06-09) 6/4/04, 18:199
Basic connections
Antenna to DVD/VCR connection
The DVD/VCR must be connected “between” the antenna and
the TV. First, disconnect the antenna from the TV and connect
it to the DVD/VCR. Then connect the DVD/VCR to the TV.
Below are 3 common methods of connecting an antenna system to a DVD/VCR. Find the type of antenna system you are
using and follow the connection diagram.
Example 1: Combination VHF/UHF antenna with 75 ohm
Example 2: Combination VHF/UHF antenna with 300 ohm
Example 3: Separate VHF and UHF antennas
VHF UHF
NOTE:
If both VHF and UHF antennas have 300 ohm twin lead (flat)
wires, use a combiner having two 300 ohm inputs and one 75
ohm output.
coaxial cable
75 ohm coaxial
cable
twin lead (flat) wire
300 ohm twin lead
(flat) wire
Combiner
75/300 ohm inputs
75 ohm output (not supplied)
300 ohm twin
lead (flat) wire
75 ohm coaxial
cable
IN
(ANT)
OUT
(TV)
DVD/VCR
Matching transformer
300 ohm input 75 ohm
output (not supplied)
IN
(ANT)
OUT
(TV)
DVD/VCR
IN
(ANT)
OUT
(TV)
DVD/VCR
DVD/VCR to TV connection
After you have connected the antenna to the DVD/VCR, you
must connect the DVD/VCR to the TV.
Below are 3 common methods of connecting your DVD/VCR
to a TV. Find the type of TV you are using and follow the connection diagram.
This DVD/VCR has a single 75 ohm output for connection to a
TV. If your TV has separate VHF and UHF antenna inputs (numbers 2 and 3 below), use a splitter to connect the DVD/VCR to
the TV for VHF and UHF reception.
Example 1: TV with single 75 ohm VHF/UHF antenna
Example 2: TV with 300 ohm UHF and 75 ohm VHF
IN
(ANT)
OUT
(TV)
DVD/VCR
Example 3: TV with 300 ohm UHF and 300 ohm VHF
IN
(ANT)
OUT
(TV)
DVD/VCR
input
75 ohm coaxial
cable (supplied)
(ANT)
IN
OUT
(TV)
DVD/VCR
antenna inputs
75 ohm coaxial cable
(supplied)
antenna inputs
75 ohm coaxial cable
(supplied)
Splitter 75 ohm input
75/300 ohm outputs
(not supplied)
Splitter 75 ohm input
300 ohm output
(not supplied)
TV
VHF/UHF
IN (ANT)
TV
UHF
VHF
TV
UHF
VHF
NOTES:
• A clear picture will not be obtained by the main unit unless
the antenna signal is good. Connect the antenna to the
main unit properly.
• For better quality recording, an indoor antenna or a
telescopic antenna is not recommended. The use of an
outdoor type antenna is required.
• If you are not sure about the connection, please refer to
qualified service personnel.
10
2D81121A[E] (10-17) 6/4/04, 18:1910
NOTE:
If a VHF or UHF antenna is used, set the TV/CABLE menu
option to the “TV” mode.
CABLE TV connections
Many cable companies offer services permitting reception of extra channels including pay or subscription channels. This DVD/
VCR has an extended tuning range and can be tuned to most cable channels without using a cable company supplied converter
box, except for those channels which are intentionally scrambled. If you subscribe to a special channel which is scrambled, you
must have a descrambler box for proper reception.
Example 1:
DVD/VCR
TV
IN
Incoming Cable
ALLOWS:*Recording of nonscrambled channels.
Use of the programmable timer.
*
Recording of one channel while watching another.
*
(ANT)
OUT
(TV)
VHF/UHF
IN (ANT)
ENGLISH
Example 2:
DVD/VCR
Converter/
Descrambler
IN
(ANT)
Incoming
Cable
OUT
(TV)
ALLOWS:*Recording of channels through the converter box
(scrambled and unscrambled).
Using the programmable timer to record only the
*
channel selected at the converter box.
PREVENTS:*Recording one channel while watching another.
Using the DVD/VCR tuner to select channels.
*
Example 3:
DVD/VCR
IN
(ANT)
Incoming Cable
OUT
(TV)
TV
VHF/UHF
IN (ANT)
NOTE:
To record from converter/descrambler, DVD/
VCR tuner must be tuned to the converter
output channel, usually channel 3 or 4.
TV
Converter/Descrambler
VHF/UHF
IN (ANT)
ALLOWS:*Recording of nonscrambled channels.
Use of the programmable timer.
*
Recording an unscrambled channel while watching any
*
channel selected at the converter box.
PREVENTS: Recording scrambled channels.
NOTE:
If you are playing a tape or using the tuner
built into the DVD/VCR, the converter must
be set to the video channel output of the DVD/
VCR (either 3 or 4).
NOTE: Whenever a Converter/Descrambler box is placed before the DVD/VCR, you must tune the DVD/VCR to the output
of the Converter/Descrambler box, usually channel 3 or 4.
2D81121A[E] (10-17) 6/4/04, 18:1911
11
Playback connections
The exact arrangement you use to interconnect various video and audio components to the DVD/VCR is dependent on the model
and features of each component. Check the Owner's Manual provided with each component for the location of video and audio
inputs and outputs.
Connect to a TV with Audio/Video Output
You can enjoy playback by connecting the unit to a TV.
Connect the unit to a TV equipped with audio input (L/R) and video input jacks using the supplied audio/video cable.
TV
DVD/VCR
Audio (L) Output
Audio (R) Output
Connect to a TV with S-Video Output (for DVD/CD playback)
If your TV has an S-VIDEO input, you can get higher quality by connecting it with the S-VIDEO output of the unit using the
S-video cable instead of connecting the video input of the TV to the VIDEO jack of the unit.
Video Output
AUDIO/VIDEO cable (supplied)
To Video
Input
TV
To Audio (R) Input
To Audio (L) Input
S-Video cable (not supplied)
DVD/VCR
To S-Video
Input
S-Video Output
S-VIDEO/COMPONENT
Video selector switch
Connect to a TV with Component Video Output (for DVD/CD playback)
You can enjoy high quality picture by connecting the unit’s COMPONENT VIDEO OUT jacks to the COMPONENT VIDEO IN
jacks of your TV with the COMPONENT video cables (not supplied).
DVD/VCR
Audio (L) Output
Audio (R) Output
AUDIO cable (not supplied)
To Audio (R) Input
To Audio (L) Input
TV
To Component
Video Output
NOTES:
• When you connect to a TV with S-video jack or component jacks, set the S-VIDEO/COMPONENT Video selector switch to
the desired position. And also you must select the corresponding video input on your TV.
• When connecting to a TV using the VIDEO or S-VIDEO jack, make sure that the PROGRESSIVE indicator on the
display window is not lit. If it is lit, the VIDEO and S-VIDEO outputs do not feed the correct signals and you cannot
see any picture. To turn off the PROGRESSIVE indicator, make the Progressive scanning mode inactive
(see page 30).
• When the component video input jacks on a TV is of the BNC type, use an adapter to convert a pin jack to a BNC jack
(not supplied).
COMPONENT VIDEO cable (not supplied)
To Component Video Input
12
2D81121A[E] (10-17) 6/4/04, 18:1912
Connect to a Stereo Amplifier with Audio Output
You can enjoy high quality audio by connecting the audio output to your amplifier.
Connect the AUDIO OUT jacks to any line-level inputs (such as AUX, DVD, CD, etc.) of an audio amplifier.
DVD/VCR
Stereo Amplifier
Audio (L) Output
Audio (R) Output
Connect to an AV Amplifier with built-in digital surround
If you are using an Amplifier with a built-in digital surround as follows, you can enjoy the various audio systems such as Dolby
Digital and DTS by using the Optical or Coaxial Digital Output.
Use this connection to connect an:
• AV amplifier with built-in *Dolby Digital decoder
• AV amplifier with built-in *DTS decoder
DVD/VCR
Video Output
Coaxial Digital Audio Output
Coaxial digital cable (not supplied)
AUDIO cable (not supplied)
Video cable (not supplied)
AV Amplifier with
built-in various
decoder as above
To Audio (L) Input
To Audio (R) Input
To Video
Input
TV
NOTE:
You may connect to a TV with a Component video cable (not supplied) or SVideo cable (not supplied) instead of a
video cable (not supplied).
ENGLISH
Connecting the optical digital cable
You may connect to an AV Amplifier with an Optical digital cable (not supplied) instead of a Coaxial digital cable.
When you connect the optical digital cable (not supplied), remove the dust protection cap from the rear panel.
When not using the optical digital cable, attach the dust protection cap to protect against dust.
NOTES:
•
The DVD OUTPUT jacks (OPTICAL, COAXIAL, AUDIO L/R, S-VIDEO and COMPONENT) are useful only for DVD section.
•
The VHS signal is output only from the composite jacks (DVD/VCR OUTPUT) and UHF/VHF OUT.
•
When you make the connections above, do not set DOLBY DIGITAL to DOLBY DIGITAL or DTS to ON on the AV Amplifier. If
you do, a loud noise will suddenly come out from the speakers, affecting your ears or causing the speakers to be damaged.
•
Caution for the optical digital audio output connector: Do not connect to an amplifier (with an optical digital input connector)
which does not contain a Dolby Digital or DTS decoder. Otherwise, any attempt to play DVDs may cause such a high level of
noise that it may be harmful to your ears and damage your speakers.
•
DTS audio will be output only from the COAXIAL or OPTICAL output. To hear DTS audio, DTS-Decoder is necessary.
•
When playing DTS-encoded CDs, only noise will be heard from the speakers or analogue stereo outputs.
•
Some DTS decoders which do not support DVD-DTS interface may not work properly with the unit.
2D81121A[E] (10-17) 6/4/04, 18:1913
13
〈+/-/ENTER/MENU〉
MENU
TIMER REC SET
AUTO REPEAT
ON OFF
ON OFF
SAP
CH SETUP
SYSTEM SETUP
〈+/-/ENTER/MENU〉
SYSTEM SETUP
CLOCK SET
LANGUAGE/IDIOMA/LANGUE
NO NOISE BACKGROUND
AUTO CLOCK
STANDARD TIME
DAYLIGHT SAVING TIME
ON OFF
ON OFF
Setting up the VCR section
Setting the video channel
To view playback of a recorded tape or DVD disc, or to
watch a program selected by the VCR's channel
selector, the TV must be set to channel 3 or 4 (video
channel).
When a TV is connected with the 75 ohm coaxial cable only.
1 Press and hold 3 or 4 on the
remote control for 3 seconds
in the standby mode to select
CH 3 or 4. The selected channel number will flash on the display for about 4 seconds.
2 Turn ON the TV and set to CH 3 or 4 to correspond with
the channel selected in step 1.
3 Press POWER to turn on the DVD/VCR.
4 Press VCR/DVD to select the VCR mode. The VCR
indicator on the front panel will light.
5 Press TV/VCR to select the VCR position.
The VCR indicator will appear in the display.
6 Select any channel to receive a TV station in your area.
The channel number will appear on the screen for about
4 seconds.
For a push-button TV tuner
If CH 3 or 4 corresponding to the video channel cannot be
tuned on your TV, proceed as follows: set the VCR 3/4
channel selector and the TV to CH 3 or 4, play back a
prerecorded tape and tune the TV to receive a sharp color
picture from the video cassette recorder. Refer to your TV
owner's manual for details.
NOTES:
• When shipped from factory, the video channel is set to
CH 3.
• If the unit does not operate properly, or No key operation (by the unit and/or the remote control): Static elec-
tricity, etc., may affect the player's operation. Disconnect the
AC power cord once, then connect it again.
Setting the language
You can choose from three different languages
(English, French and Spanish) for the on-screen displays.
1 Press VCR MENU.
The VCR menu screen
will appear. Press SET +
or – to select the “SYSTEM SETUP” menu, then
press ENTER.
If you use the unit for the
first time and press VCR
MENU, instead of the main menu screen on the right the
“SYSTEM SETUP” menu screen in step 2 may appear.
2 Press SET + or – to select
the “LANGUAGE” option,
then press ENTER.
3 Press SET + or – to select
the desired language: English (ENGLISH), Spanish
(ESPAÑOL) or French
(FRANCAIS), then press
ENTER.
4 Press VCR MENU until the MENU screen is cleared.
NOTES:
• Both the VCR and the DVD have their own menu option
(See page 23).
• If no buttons are pressed for more than 60 seconds, the
MENU screen will return to normal TV-operation automatically.
14
2D81121A[E] (10-17) 6/4/04, 18:1914
Auto clock setting
The Auto Clock function will automatically set the builtin clock (Month, Day, Year and Time) when the DVD/
VCR is connected to an Antenna or Cable system and it
is turned off. As the DVD/VCR searches for a receivable
station in your area and it receives a broadcast signal
for Auto Clock, the Auto Clock needs several minutes
to set itself.
1 Connect the Antenna or Cable system.
• If you use a cable box, turn it on.
2 Plug the AC Power cord to the AC outlet.
3 Make sure the DVD/VCR is turned off.
• If you press POWER, the Auto Clock set is not effective.
4 Wait at least three minutes and press POWER.
5 Press DISPLAY to check the clock on the screen.
6 If the clock is not set, check the Antenna condition. The
Auto Clock may not function properly if the reception condition is not good.
Auto clock adjustment
The Auto Clock Adjustment will be performed at 12:00 PM
everyday if you turn off the DVD/VCR.
• If you use a cable box and you want the Auto Clock adjustment to be performed, the cable box must be left on.
• The Auto Clock Adjustment is not effective when there is a
difference of more than 5 minutes between the built-in
clock time and the actual time.
To set auto clock to off
When shipped from factory the “AUTO CLOCK” option is set
to ON.
But if you do not want Auto Clock set (Adjustment):
1 Turn on the DVD/VCR.
2 Press VCR MENU.
3 Press SET + or – to select the “SYSTEM SETUP’ option,
then press ENTER.
4 Press SET + or – to select the “AUTO CLOCK” option.
5 Press ENTER to select “OFF”.
6 Press VCR MENU repeatedly to return to the normal
screen.
• When the “AUTO CLOCK” is set to “OFF”, the Auto Clock
adjustment does not function.
• Set the clock manually (see page 16).
4 Press SET + or – to select your time zone, then press
ENTER.
ATLANTIC : GMT – 4 hours
(GMT: Greenwich Mean Time)
EASTERN : GMT – 5 hours
CENTRAL : GMT – 6 hours
MOUNTAIN : GMT – 7 hours
PACIFIC : GMT – 8 hours
ALASKA : GMT – 9 hours
HAWAII : GMT – 10 hours
AUTO : AUTO SET
5 Press VCR MENU twice to return to the normal screen.
NOTE:
To be able to select the standard time, the clock must first
be set by “AUTO CLOCK” once.
Daylight saving time setting
You can set the Daylight saving time automatically or
manually.
1 Press VCR MENU. Press SET +
or – to select the “SYSTEM
SETUP” option, then press
ENTER.
2 Press SET + or – to select the
“DAYLIGHT SAVING TIME”
option, then press ENTER.
3 Press SET + or – to select one of
the options, then press ENTER.
Press VCR MENU until the
MENU screen is cleared.
ON: for manual setting
(forward one hour)
OFF: for manual setting
(back one hour)
AUTO: for automatic setting
(read XDS in the signal)
When you want to set the Daylight Saving Time manually, on
the first Sunday in April you set to “ON”, and on the last Sunday in October you set to “OFF”.
MENU
TIMER REC SET
AUTO REPEAT
SAP
CH SETUP
SYSTEM SETUP
〈+/-/ENTER/MENU〉
SYSTEM SETUP
CLOCK SET
LANGUAGE/IDIOMA/LANGUE
NO NOISE BACKGROUND
AUTO CLOCK
STANDARD TIME
DAYLIGHT SAVING TIME
〈+/-/ENTER/MENU〉
DAYLIGHT SAVING TIME
á+/-
ON
OFF
AUTO
/ENTER/MENU
ON OFF
ON OFF
ON OFF
ON OFF
ñ
ENGLISH
To set standard time
In the rare event that you live within broadcast range of two
stations in two different time zones, the DVD/VCR may
recognize the wrong station for the Auto Clock set.
To correct the situation:
1 Press VCR MENU.
2 Press SET + or – to select the “SYSTEM SETUP”
option, then press ENTER.
3 Press SET + or – to select the “STANDARD TIME”
option, then press ENTER.
2D81121A[E] (10-17) 6/4/04, 18:1915
NOTES:
• When shipped from factory, the “DAYLIGHT SAVING
TIME” option is set to “AUTO” position.
• When the clock is not set, Daylight Saving Time setting is
not available.
• When there is no Daylight Saving Time in your area, always
select “OFF” position in step 3.
15
Manual clock setting
You must set the date and time manually for Timer
Recordings, ON/OFF Timer and Daylight Saving Time if
the Auto Clock process did not set them correctly.
Example: Setting the clock to “8:30 AM”, 30th (SAT)
October, 2004.
1 Press VCR MENU.
Press
SET + or –
“SYSTEM
to select the
SETUP” option, then
press ENTER.
2 Press SET + or – to select the
“CLOCK SET” option, then press
ENTER.
3 Press SET + or – to set the month,
then press ENTER.
4 Set the day, year and time as in
MENU
TIMER REC SET
AUTO REPEAT
SAP
CH SETUP
SYSTEM SETUP
〈+/-/ENTER/MENU〉
SYSTEM SETUP
CLOCK SET
LANGUAGE/IDIOMA/LANGUE
NO NOISE BACKGROUND
AUTO CLOCK
STANDARD TIME
DAYLIGHT SAVING TIME
〈+/-/ENTER/MENU〉
ON OFF
ON OFF
ON OFF
ON OFF
step 3.
10
After setting the clock, date and time
starts functioning automatically.
MONTH
30 (SAT)
DAY
2004
YEAR
TIME
á+/-
/ENTER/CANCEL/MENU
8:30 AM
ñ
NOTES:
• After a power failure or disconnection of the power plug,
the time display will be lost. In this case, set the present
time again if the Auto Clock did not set correctly.
• To move cursor backward, press CANCEL.
Tuner setting
This DVD/VCR is equipped with a channel memory
feature which allows channels to skip up or down to the
next channel set into memory, skipping over unwanted
channels. Before selecting channels, they must be
programmed into the DVD/VCR’s memory. In addition to
normal VHF and UHF channels, this DVD/VCR can
receive up to 113 Cable TV channels. To use this DVD/
VCR with an antenna, set the TV/CABLE menu option to
the TV mode. When shipped from the factory, this menu
option is in the CABLE mode.
TV/CABLE selection
1 Press VCR MENU.
Press SET + or – to select the “CH
SETUP” mode, then press ENTER.
MENU
TIMER REC SET
AUTO REPEAT
SAP
CH SETUP
SYSTEM SETUP
ON OFF
ON OFF
Automatic memory tuning
The VCR can receive a maximum of 181 channels by
presetting the channels into memory.
1 In the “CH SETUP” menu, press
SET + or – to select “AUTO CH
MEMORY”, then press ENTER.
2 The DVD/VCR will begin memoriz-
CH SETUP
TV CABLE
AUTO CH MEMORY
ADD/DELETE
á+/-
/ENTER/MENU
ñ
ing all the channels available in
your area.
To add/delete channels
You can add the channels you want or delete the channels you do not want manually.
1 Press VCR MENU.
Press SET + or – to select the
“CH SETUP” mode, then press
CH SETUP
TV CABLE
AUTO CH MEMORY
ADD/DELETE
ENTER.
2 Press SET + or – to select the
á+/-
/ENTER/MENU
ñ
“ADD/DELETE” mode, then press
ENTER.
CH 003ADD
3 Select the desired channel to be
memorized or deleted using SET
+ or – button, or using Number
keys.
á
+/-/0-9/ENTER/MENU
ñ
4 Press ENTER to select the “ADD” or “DELETE”.
5 Press VCR MENU until the MENU screen is cleared.
Noise elimination
When you don't want to receive a weak signal broadcast, the Blue back screen can be obtained by selecting
the NO NOISE BACKGROUND “ON”. When the unit is
shipped from the factory, the NO NOISE BACKGROUND
is set to the “ON”.
1 In the “SYSTEM SETUP” menu,
press SET + or – to select “ NO
NOISE BACKGROUND”.
2 Press ENTER to select the “ON”
position.
3 Press VCR MENU until the MENU screen is cleared.
SYSTEM SETUP
CLOCK SET
LANGUAGE/IDIOMA/LANGUE
NO NOISE BACKGROUND
AUTO CLOCK
STANDARD TIME
DAYLIGHT SAVING TIME
〈+/-/ENTER/MENU〉
ON OFF
ON OFF
á+/-
/ENTER/MENU
2 Press SET + or – to select the
TV/CABLE mode.
3 Press ENTER to select the TV or
CH SETUP
TV CABLE
AUTO CH MEMORY
ADD/DELETE
CABLE mode.
The arrow indicates the selected
á+/-
/ENTER/MENU
mode.
TV - VHF/UHF channels
CABLE - CABLE TV channels
4 Press VCR MENU until the MENU screen is cleared.
16
2D81121A[E] (10-17) 6/4/04, 18:1916
ñ
ñ
Tape playback operation
Loading and Unloading a cassette tape
Use only video cassette tapes marked .
Loading
Push the center of the tape until it is automatically retracted
into the unit.
Automatic power on and play
When loading a cassette tape without the erase prevention
tab intact, the unit will turn on automatically and playback will
start immediately.
Insert the cassette with its labeled side facing you.
An inverted video cassette cannot be inserted.
Unloading
To unload a video cassette, press EJECT on the remote
control, or press 5 (EJECT) on the unit.
Automatic eject
If the unit automatically rewinds the tape to the
beginning (AUTO REWIND FEATURE), the tape will
be ejected automatically.
To prevent accidental erasure
After recording, break off the erase prevention tab if you do
not wish to record over the tape.
Screwdriver
Cassette tape playback
Load a prerecorded tape (When loading a cassette tape
without the erase prevention tab, playback will start automatically).
To start playback
Press PLAY to begin playback.
“ ” will appear on the screen.
To stop playback
Press STOP once.
The tape will stop, but remain fully loaded and ready to play.
“ ” will appear on the screen.
NOTES:
• This unit selects the playback tape speed SP, LP or SLP
automatically.
• The Cassette tape and DVD disc can be played back simultaneously. If you press VCR/DVD, the tape playback and
DVD playback alternate with each other on the screen.
To rewind or forward the tape rapidly
Press REW or F.FWD in the Stop mode.
“ ” or “ ” will appear on the screen.
FORWARD/REVERSE PICTURE SEARCH
If you want to see the tape during REW or F.FWD mode,
press and hold the REW or F.FWD. The backward or
forward visual search picture will be seen on the screen.
Release to return to the REW or F.FWD mode.
ENGLISH
Erase prevention tab
To record again
Cover the hole with adhesive tape.
Be careful the tape does not extend past the edges of the
video cassette housing.
Adhesive tape
Tape Speed
SP (Standard Play)
2-2/3 hours 2 hours 1 hour
SLP (Super Long Play)
Video cassette tape
T-160 T-120 T-60
8 hours 6 hours 3 hours
Special playback
Picture Search
Reverse picture search function
Press REW x 1 or x 2 during the playback.
Forward picture search function
Press F.FWD x 1 or x 2 during the playback.
To return to playback: Press PLAY.
SPEED SEARCH TIMES
TAPE SPEED
SP (Standard Play)
LP (Long Play)
SLP (Super Long Play)
PICTURE SEARCH SPEED
PRESS ONCE
3 X
7 X
9 X
PRESS TWICE
5 X
9 X
15 X
Still Picture
Press PAUSE during playback. To resume normal playback:
Press PLAY.
17
2D81121A[E] (10-17) 6/4/04, 18:1917
Slow Motion
During playback press SLOW.
To return to playback: Press PLAY or SLOW.
Slow tracking and vertical lock adjustment
If noise bars appear in the picture during slow motion, press
the TRK + or – to reduce the noise bars.
If the still picture jitters excessively, press TRK + or – to
stabilize the still picture.
Frame by Frame picture
Press PAUSE during playback.
Press SLOW one by one: The picture advances frame by
frame.
To return to playback: Press PLAY or PAUSE.
Adjusting tracking condition
Automatic tracking adjustment
Whenever you insert a tape and start playback, automatic
tracking starts working and continuously analyzes the signal
to enable optimum picture quality during playback.
Manual tracking adjustment
If automatic tracking cannot eliminate noises well during
playback, press TRK +/– to eliminate the noises.
“MANUAL TR.” will appear. Press it briefly for a fine adjustment,
or press and hold for a coarse adjustment.
• Press ATR to reactivate automatic tracking again.
“AUTO TR.” will appear.
Repeat playback
The entire video tape will be played until its end. The tape will
then automatically rewind to the beginning and the playback
will be repeated.
1
Press VCR MENU. Press SET + or – to select “AUTO
REPEAT”.
Then press ENTER to se-
2
lect “ON” or “OFF”.
If “ON” is selected, the play-
back will be repeated endlessly.
Press VCR MENU until the menu screen is cleared.
3
if you press DISPLAY, “ ” will appear on the screen.
To start the playback, press PLAY.
4
The playback will be repeated endlessly.
To cancel repeat mode:
Follow the above step 1, then press ENTER to select the
OFF position. Press VCR MENU to return to the TV.
NOTES:
•
The audio output is muted during SPEED SEARCH, STILL,
FRAME ADVANCE and SLOW MOTION.
• During picture search mode there will be noise bars which are
caused by the system.
• The Special Playback will automatically change to playback
after approx. 5 minutes to protect the video tape against
excessive wear.
MENU
TIMER REC SET
AUTO REPEAT
SAP
CH SETUP
SYSTEM SETUP
ON OFF
ON OFF
ZERO RETURN function
This function makes tape-rewinding stop at the counter
00:00:00 position automatically.
Press DISPLAY.
1
The counter display shows the tape
running time during playback or recording.
Press COUNTER RESET at the
2
desired tape position. The counter
display will be reset to the
“00:00:00” position (e.g. the
beginning of recording).
Press STOP when playback or recording is finished.
3
Press ZERO RETURN.
The tape will be rewinded or fast forwarded and automatically stop at the “00:00:00” position.
VCR
VCR
The CLOCK/COUNTER-button
Press CLOCK/COUNTER. The clock and tape counter alternate with each other in the display.
NOTES:
•
If you rewind the tape beyond “00:00:00”, a minus sign
(“–”) will be displayed in front of the time.
•
When you load a tape, the counter will reset to “00:00:00”.
•
The counter does not function on nonrecorded (blank) sections of the tape. When you rewind, fast forward or play tapes
through blank sections, the counter stops.
Video index search system
This function enables you to locate the beginning of any
recording made on the VCR.
Recording an INDEX MARK
The Index Search function automatically records an INDEX
mark on the tape whenever a recording is initiated.
Index Search
77
Press INDEX
For Succeeding programs: Press INDEX
For Preceding programs: Press INDEX
(Additional press increases the INDEX NO. up to 9.)
When the INDEX
searching the INDEX NO. selected and finds the portion,
then playback starts automatically.
To stop the Index Search, press STOP.
NOTES:
When you record an INDEX mark at the very beginning of the
•
tape, the mark may not be found.
During INDEX search, the tape may stop and begin to play
•
at a slightly different location.
INDEX may not function properly with old or worn out video
•
tapes.
INDEX marks may not be found if it is extremely close to the
•
point where the search began.
In recording, if you stop recording temporarily, the INDEX
•
mark is not recorded on the tape.
66
7 or
6 during stop or play mode.
77
66
77
6 6
7 or
6 is pressed, the unit starts
77
6 6
77
7.
77
66
6 .
66
18
2D81121A[E] (18-23) 6/4/04, 18:1918
Recording
Recording a TV program
Recording and viewing the same TV program.
Load a cassette tape with the erase prevention tab intact.
1
The unit will automatically turn on.
Press SPEED to select the desired tape speed SP or
2
SLP.
The tape counter and SP or SLP will appear on the
screen for about 4 seconds.
3
Set the TV/CABLE option to the appropriate position
(See page 16).
Press Number keys or CH / to select the channel
4
to be recorded.
1-9 Press 0 twice and then 1-9 as required.
10-12 Press 0 first and then the remaining 2 digits
13-99 Press 2 digits in order.
100-125 Press the 3 digits in order.
VHF/UHF/CABLE CHANNELS
Example: To select 2, Press “002”.
in order from left to right.
Example: Press 012 for “12”.
Example: Press 22 for “22”.
Example: Press 110 for “110”.
TV CABLE
VHF
2-13
UHF
14-69
60-85 (AAA) (ZZZ)
VHF
2-13
STD/HRC/IRC
14-36 (A) (W)
37-59 (AA) (WW)
86-94 (86) (94)
95-99 (A-5) (A-1)
100-125 (100)(125)
01 (5A)
To stop recording
Press STOP to stop recording.
“ ” will appear on screen for about 4 seconds.
To stop recording temporarily
Press PAUSE/STILL to avoid recording unwanted material.
“ ” will appear on screen for about 4 seconds.
Press again to continue the recording.
NOTES:
•
The pause function will be released after 5 minutes to prevent
damage to the tape or the VCR. The VCR will change to the
STOP mode.
•
You can select a recording channel in the recording pause
mode.
Recording one program while watching
another
While the VCR is recording, press TV/VCR to select the TV
position.
The “VCR” will go off and recording will continue.
Select the TV channel you want to watch by using the TV
channel selector.
NOTE:
Some CABLE hookups do not permit viewing one channel
while recording another. See page 11.
To Display VCR operation Status
Press DISPLAY. The clock, day of the week and more informa-
tion will be indicated.
While watching TV
CLOCK
DAY OF THE WEEK
8:47
AM
MON
STEREO SAP
CH 125
CHANNEL
ENGLISH
Press REC/OTR.
5
“ ” will appear on the screen
for about 4 seconds and “REC”
will appear on the display.
INDEX
NOTES:
• If the erase prevention tab is removed, the tape will eject when
REC/OTR is pressed for recording.
• If you wish to watch the DVD playback during the normal
recording on VCR, press VCR/DVD to change to DVD mode
and perform the DVD playback (see page 24).
• You can not record disc material in DVD, Audio CD, etc. onto
a video tape with this DVD/VCR.
CH 110
00 : 00 : 00 SP
STEREO AND
SECOND AUDIO
PROGRAM (SAP)
While operating a tape
HI-FI
STEREO
AUTO
REPEAT
To cancel the display: Press DISPLAY until all indicators
disappear.
8:30AM MON
HI-FI
REAL TIME COUNTER
00 : 15 : 12 SP
TAPE
SPEED
OPERATING
MODE
TAPE IN
Auto Rewind feature
This VCR will automatically rewind the tape when the tape has
ended (except during OTR and TIMER REC). It will also eject
the tape.
19
2D81121A[E] (18-23) 6/4/04, 18:1919
One-touch Timer Recording (OTR)
The One-touch Timer Recording feature provides a
simple and convenient way to make a timed recording.
Example: One-touch Timer Recording for 30 minutes.
Load a cassette tape with the erase prevention tab
1
intact.
The unit will automatically turn on.
Press SPEED to select the desired tape speed SP or
2
SLP.
The tape counter and SP or SLP will appear on the
screen for about 4 seconds.
3
Set the TV/CABLE option to the appropriate position.
Press Number keys or CH / to select the channel
4
to be recorded.
Press REC/OTR. Press the button again to stop record-
5
ing after 30 minutes. Each additional press of REC/OTR
will increase recording time as shown in the chart below,
up to a maximum of 6 hours. The OTR and recording time
will appear on the screen for about 4 seconds. And, REC
will keep blinking in the display.
Press
Recording time Press
once
twice
3 times
4 times
5 times
NORMAL REC
0:30
1:00
1:30
2:00
6 times
7 times
8 times
9 times
10 times
Recording time
3:00
4:00
5:00
6:00
NORMAL REC
To cancel OTR
Press STOP or turn off the power.
“ ” will appear on screen for about 4 seconds.
NOTE:
If you wish to watch the DVD playback during the OTR, press
VCR/DVD to change to DVD mode and perform the DVD
playback (see page 24).
20
Timer recording
Timer recording can be programmed on-screen with the
remote control. The built-in timer allows automatic
unattended recording of up to 8 programs within 1 month.
Example: Program a timer recording for the 26th day,
channel 125 (CABLE), 11:00 - 11:30 PM on timer program
number 1 (Tape speed: SLP).
Press VCR MENU. Select
1
the “TIMER REC SET”
option, then press ENTER.
Press SET + or – to select
2
one of the program line,
then press ENTER.
Press SET + or – to select
3
the date, then press
ENTER.
Set the start time, end time,
4
channel and tape speed as
in step 3.
NOTES:
• Press CANCEL to move cursor backward for correction.
• To record from external source set the channel to “L”. “L”
will appear next to CH 125 (or 69).
To enter other programs, repeat step 2 through 4.
5
• To return to the normal screen, press VCR MENU twice.
6
Press TIMER REC. The clock symbol( ) will appear on
the display and the VCR stands by for recording. At the
same time, VCR mode will change to DVD mode
automatically. You can use DVD even if the VCR is in the
Timer recording mode.
If you do not use the DVD, turn the power off.
The timer recording will start at 20 seconds before the
time you predetermined.
NOTES:
• If the clock symbol( ) does not appear on the display
in spite of the pressing of TIMER REC, the cassette may
not have been loaded yet. (see page 17)
• If the cassette is ejected in spite of the pressing of TIMER
REC, the erase prevention tab of the cassette may have
been removed. (see page 17)
NOTES:
• If the clock symbol ( ) blinks when the timer recording
ended, the TV program has not been completely recorded
because of an insufficient tape supply. Press TIMER REC to
cancel the timer program or press EJECT to remove the
cassette tape.
• During timer recording standby mode, the VCR mode cannot
be selected. To use the VCR, press TIMER REC at first, then
press VCR/DVD to change to VCR mode. After you use the
VCR,
press TIMER REC again to put the VCR into timer
recording standby mode.
• If you press TIMER REC during timer recording, the record
ing operation will
again within the programmed time, the recording operation will
start again.
• After a power failure or disconnection of the power plug, all
programmed recording settings and time display will be lost
upon resumption of power. In this case, reset the clock (see
page 16) and reprogram any timer recordings.
be interrupted. If you press TIMER REC
MENU
TIMER REC SET
AUTO REPEAT
SAP
CH SETUP
SYSTEM SETUP
á+/-
/ENTER/MENU
DATE START END CH
26(SU)11:00PM11
á+/-
/ENTER/CANCEL/MENU
ON OFF
ON OFF
ñ
:30PM125
SLP
ñ
2D81121A[E] (18-23) 6/4/04, 18:1920
Timer recording special case
Weekly (e.g. WKL-TU: each Tuesday) or daily (e.g. MO-SA:
Monday to Saturday) Timer recording
Follow the procedure of timer recording on the previous page.
At picture 3 press SET + or – repeatedly until the desired setting
appears. Then press ENTER.
When you press SET – repeatedly, the indicator at DATE will
change as follows, in this case the day is Friday.
The current day (Friday) SU-SA (Sunday to Saturday)
One month later
minus one day
MO-SA (Monday to Saturday)
MO-FR (Monday to Friday)
WKL-WE WKL-TH (Weekly Thursday)
(Weekly Wednesday)
DATE START END CH
WKL-WE
á+/-
/ENTER/CANCEL/MENU
ñ
In case Timer programs-overlap
•
Do not overlap timer programs as portions of the conflicting
programs will be lost. The first recording time has priority over
the next recording time as shown in the diagram below.
Program 1
Program 2
Program 3
Recording
Control Settings
8 : 00
Prog.1
9 : 00
Deleted Parts
Non Recorded Portion Parts
Prog.2 Prog.3
10 : 00
11 : 00
Confirmation / Cancellation of the Timer
recording
If the Timer has been activated, press TIMER REC to
1
deactivate the Timer. The clock symbol( ) will disappear. Then press VCR/DVD to change to VCR mode.
To confirm Timer program:
2
At picture 1 on the previous
page select the “TIMER REC
SET” option and press EN-
TER.
Then the timer program list
as right will appear on the
screen.
To cancel Timer program:
3
Press SET + or – to select
the unnecessary program,
then press CANCEL to cancel the program.
Press VCR MENU repeatedly until the TV-picture appears.
4
NOTES:
• If there are other timer record programs remaining, TIMER
REC must be pressed to reactivate the timer, otherwise the
remaining timer record programs will be ignored.
• You cannot confirm the Timer program during timer recording operation.
•
You can also correct the programmed setting in program
confirm mode.
At step 2 above, press ENTER to enter the program input
mode. Then press ENTER repeatedly until the item you wish
to correct blinks. Then correct the data with SET + or –.
Then press VCR MENU repeatedly until the TV-picture
appears.
DATE START END CH
26(SU)11:00PM11
á+/-
/ENTER/CANCEL/MENU
DATE START END CH
á+/-
/ENTER/CANCEL/MENU
DATE START END CH
26(SU)11:00PM11
–––––– –:–– –:–– –––
–––––– –:–– –:–– –––
–––––– –:–– –:–– –––
–––––– –:–– –:–– –––
–––––– –:–– –:–– –––
–––––– –:–– –:–– –––
–––––– –:–– –:–– –––
á+/–
/ENTER/CANCEL/MENU ñ
:30PM125
:30PM125
SLP
ñ
Ð
ñ
SLP
–
–
–
–
–
–
–
ENGLISH
NOTES:
•
The daily/weekly recording can be made continuously until
the recording is canceled or the tape reaches the end.
•
During timer recording the automatic rewinding mechanism
does not function.
2D81121A[E] (18-23) 6/4/04, 18:1921
21
Loading...