MC7101
User’s Guide
CD Clock Radio with
Dual Alarm
Before operating this product,
please read these instructions completely.
SAFETY PRECAUTIONS
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER
SERVICING TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol within an
equilateral triangle is intended to alert the user to the
presence of uninsulated dangerous voltage within the
product’s enclosure that may be of sufficient magnitude to
constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is
intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in the
literature accompanying the appliance.
Invisible and hazardous laser radiation when open and
interlock failed or defeated.
FCC WARNING:
This equipment may generate or use radio frequency energy. Changes or
modifications to this equipment may cause harmful interference unless the
modifications are expressly approved in the instruction manual. The user could
lose the authority to operate this equipment if an unauthorized change or
modification is made.
Avoid direct exposure to beam.
LASER SAFETY: This unit employs a laser. Only qualified service personnel
should attempt to service this device due to possible eye injury.
CAUTION: USE OF CONTROLS, ADJUSTMENTS OR PERFORMANCE
PROCEDURE HEREIN MAY RESULT IN HAZARDOUS RADIATION
EXPOSURE.
SURGE PROTECTORS:
It is recommended to use a surge protector for AC connection. Lightning and
power surges ARE NOT covered under warranty for this product.
1
INFORMATION:
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
• Consult the dealer or an experienced radio/TV technician for help.
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
ATTENTION:
POUR ÉVITER LES CHOC ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE
LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISES ET POUSSER
JUSQU’AU FOND.
IMPORTANT SAFETY INSTRUCTIONS
Before using the unit, be sure to read all operating
instructions carefully. Please note that these are general
precautions and may not pertain to your unit. For
example, this unit may not have the capability to be
connected to an outdoor antenna.
1. READ INSTRUCTIONS
All the safety and operating instructions should be read
before the product is operated.
2. RETAIN INSTRUCTIONS
The safety and operating instructions should be retained
for future reference.
3. HEED WARNINGS
All warnings on the product and in the operating
instructions should be adhered to.
4. FOLLOW INSTRUCTIONS
All operating and use instructions should be followed.
5. CLEANING
Unplug this product from the wall outlet before cleaning.
Do not use liquid cleaners or aerosol cleaners. Use a dry
cloth for cleaning.
6. ATTACHMENTS
Do not use attachments not recommended by the
product's manufacturer as they may cause hazards.
7. WATER AND MOISTURE
Do not use this product near water–for example: near a
bathtub, washbowl, kitchen sink or laundry tub; in a wet
basement; or near a swimming pool.
8. ACCESSORIES
Do not place this product on an unstable cart, stand,
tripod, bracket or table. The product may fall, causing
serious injury and serious damage to the product. Use
only with a cart, stand, tripod, bracket or table
recommended by the manufacturer or sold with the
product. Any mounting of the product should follow the
manufacturer’s instructions, and should use a mounting
accessory recommended by the manufacturer.
8A. An appliance and cart combination should
be moved with care. Quick stops,
excessive force and uneven surfaces may
cause the appliance and cart combination
to overturn.
9. VENTILATION
Slots and openings in the cabinet and in the back or
bottom are provided for ventilation, to ensure reliable
operation of the product and to protect it from
overheating. These openings must not be blocked or
covered. The openings should never be blocked by
placing the product on a bed, sofa, rug or other similar
surface. This product should never be placed near or
over a radiator or heat source.
be placed in a built-in installation such as a bookcase or
rack unless proper ventilation is provided or the
This product should not
2
IMPORTANT SAFETY INSTRUCTIONS
ANTENNA
LEAD IN
WIRE
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810-20)
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
GROUND CLAMPS
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250, PART H)
NEC - NATIONAL ELECTRICAL CODE
ELECTRIC
SERVICE
EQUIPMENT
GROUND
CLAMP
S2898A
manufacturer's instructions have been adhered to.
0. POWER SOURCES
1
his product should be operated only from the type of
T
power source indicated on the marking label. If you are
not sure of the type of power supply to your home,
consult your appliance dealer or local power company.
For products intended to operate from battery power, or
ther sources, refer to the operating instructions.
o
11. GROUNDING OR POLARIZATION
his product is equipped with a polarized alternating-
T
current line plug (a plug having one blade wider than the
other). This plug will fit into the power outlet only one
way. This is a safety feature. If you are unable to insert
the plug fully into the outlet, try reversing the plug. If the
plug should still fail to fit, contact your electrician to
replace your obsolete outlet. Do not defeat the safety
purpose of the polarized plug.
12. POWER-CORD PROTECTION
Power-supply cords should be routed so that they are
not likely to be walked on or pinched by items placed
upon or against them, paying particular attention to
cords at plugs, convenience receptacles, and the point
where they exit from the appliance.
13. LIGHTNING
To protect your product from a lightning storm, or when
it is left unattended and unused for long periods of time,
unplug it from the wall outlet and disconnect the antenna
or cable system. This will prevent damage to the product
due to lightning and power-line surges.
14. POWER LINES
An outside antenna system should not be located in the
vicinity of overhead power lines or other electric light or
power circuits, or where it can fall into such power lines
or circuits. When installing an outside antenna system,
extreme care should be taken to keep from touching
such power lines or circuits as contact with them might
be fatal.
15. OVERLOADING
Do not overload wall outlets and extension cords as this
can result in a risk of fire or electric shock.
16. OBJECT AND LIQUID ENTRY
Never push objects of any kind into this product through
openings as they may touch dangerous voltage points
or short out parts that could result in fire or electric
shock. Never spill or spray any type of liquid on the
product.
17. SERVICING
Do not attempt to service this product yourself as
opening or removing covers may expose you to
dangerous voltage or other hazards. Refer all servicing
to qualified service personnel.
18. REPLACEMENT PARTS
When replacement parts are required, be sure the
service technician uses replacement parts specified by
the manufacturer or those that have the same
characteristics as the original part. Unauthorized
substitutions may result in fire, electric shock or other
hazards.
19. SAFETY CHECK
Upon completion of any service or repairs to this
product, ask the service technician to perform safety
hecks to determine that the product is in proper
c
perating condition.
o
20. WALL OR CEILING MOUNTING
The product should be mounted to a wall or ceiling only
as recommended by the manufacturer.
21. DAMAGE REQUIRING SERVICE
nplug the product from the wall outlet and refer
U
servicing to qualified service personnel under the
ollowing conditions:
f
a. When the power-supply cord or plug is damaged.
b. If liquid has been spilled or objects have fallen into the
product.
c. If the product has been exposed to rain or water.
d. If the product does not operate normally by following the
operating instructions. Adjust only those controls that are
covered by the operating instructions, as an adjustment
of other controls may result in damage and will often
require extensive work by a qualified technician to
restore the product to its normal operation.
e. If the product has been dropped or the cabinet has been
damaged.
f. When the product exhibits a distinct change in
performance–this indicates a need for service.
22. HEAT
The product should be situated away from heat sources
such as radiators, heat registers, stoves or other
products (including amplifiers) that produce heat.
23. NOTE TO CATV SYSTEM INSTALLER
This reminder is provided to call the CATV system
installer's attention to Article 820-40 of the NEC that
provides guidelines for proper grounding and, in
particular, specifies that the cable ground shall be
connected to the grounding system of the building, as
close to the point of cable entry as practical.
24. OUTDOOR ANTENNA GROUNDING
If an outside antenna is connected to the product, be
sure the antenna system is grounded so as to provide
some protection against voltage surges and built-up
static charges. Section 810 of the National Electric
Code, ANSI/NFPA 70, provides information with respect
to proper grounding of the mast and supporting
structure, grounding of the lead-in wire to an antenna
discharge product, size of grounding conductors,
location of antenna discharge product, connection to
grounding electrodes and requirements for grounding
electrodes.
EXAMPLE OF ANTENNA GROUNDING AS PER
NATIONAL ELECTRICAL CODE
3
Dear Customer:
A
S
S
O
C
I
A
T
I
O
N
EST. 1924
E
L
E
C
T
R
O
N
I
C
I
N
D
U
S
T
R
I
E
S
EIA
We
LISTENING
For A Lifetime
Want You
Selecting fine audio equipment such as the unit you’ve just purchased is only the start of your
musical enjoyment. Now it’s time to consider how you can maximize the fun and excitement
your equipment offers. This manufacturer and the Electronic Industries Association’s
Consumer Electronics Group want you to get the most out of your equipment by playing it at a
safe level. One that lets the sound come through loud and clear without annoying blaring or
distortion—and, most importantly, without affecting your sensitive hearing.
Sound can be deceiving. Over time your hearing “comfort level” adapts to higher volumes of
sound. So what sounds “normal” can actually be loud and harmful to your hearing. Guard
against this by setting your equipment at a safe level BEFORE your hearing adapts.
To establish a safe level:
• Start your volume control at a low setting.
• Slowly increase the sound until you can hear it comfortably and clearly, and without distortion.
Once you have established a comfortable sound level:
• Set the dial and leave it there.
Taking a minute to do this now will help to prevent hearing damage or loss in the future. After
all, we want you listening for a lifetime.
We Want You Listening For A Lifetime
Used wisely, your new sound equipment will provide a lifetime of fun and enjoyment. Since
hearing damage from loud noise is often undetectable until it is too late, this manufacturer and
the Electronic Industries Association’s Consumer Electronics Group recommend you avoid
prolonged exposure to excessive noise. This list of sound levels is included for your protection.
Decibel
Level
Example
30 Quiet library, soft whispers
40 Living room, refrigerator, bedroom away from traffic
50 Light traffic, normal conversation, quiet office
60 Air conditioner at 20 feet, sewing machine
70 Vacuum cleaner, hair dryer, noisy restaurant
80 Average city traffic, garbage disposals, alarm clock at two feet
THE FOLLOWING NOISES CAN BE DANGEROUS UNDER CONSTANT EXPOSURE:
90 Subway, motorcycle, truck traffic, lawn mower
100 Garbage truck, chain saw, pneumatic drill
120 Rock band concert in front of speakers, thunderclap
140 Gunshot blast, jet engine
180 Rocket launching pad
Information courtesy of the Deafness Research Foundation.
4
FRONT
REAR
LOCATION OF CONTROLS
1. TIME Button
2. HOUR Button
3. MIN (Minute) Button
4. CD DOOR OPEN
5. Display DIM Button
6. ALARM 1 Button
7. Tune/Skip/Search
8. STOP (■)/OFF Button
9. SNOOZE/SLEEP
10. Play/Pause
11. Tune/Skip/Search
12. Display
13. ALARM 2 Button
14. AM/FM/Power On
15. VOLUME Down Button
16. VOLUME Up Button
17. PROGRAM Button
18. CD MODE Button
19. Left Speaker
20. Right Speaker
21. PRESETS Button
22. SEEK Button
23. FM Antenna Wire
24. Stand
25. LINE IN Jack
26. DC 6V IN Jack
27. Battery Compartment
28. Headphones Jack
Switch
Button
Button
®p)/CD/
Power On Button
Button
Button
(Bottom of Unit)
(
m
l
Z
5
INSTALLATION
+– +–
AC ADAPTER CONNECTION
Connect the AC adapter (included) to an AC outlet having 120V, 60Hz AC only.
Plug the small end into the DC jack on the rear of the unit.
CAUTION: Do not touch the AC adapter with wet hands. Fully insert the plug
without exposing any part of the blade.
DC 6V
INSERTING BATTERIES
Two (2) “AAA” size batteries can also be used to power and/or to provide a backup
for the clock and alarm time for this unit as follows:
1. Open the battery door by pushing in on the tabs, then removing the door.
2. Insert two (2) “AAA” batteries as shown. Alkaline batteries are recommended
3. Place the battery door back on the compartment.
NOTE: The batteries are used to back-up the clock, alarm time and radio preset
memories when the AC adapter is disconnected or there is a power failure.
Z
for the longest playing time.
BATTERY PRECAUTIONS
Follow these precautions when using batteries in this device:
1. Use only the size and type of batteries specified.
2. Be sure to follow the correct polarity when installing the batteries as indicated in the
battery compartment. Reversed batteries may cause damage to the device.
3. Do not mix different types of batteries together (e.g. Alkaline, Rechargeable and
Carbon-zinc) or old batteries with fresh ones.
4. If the device is not to be used for a long period of time, remove the batteries to
prevent damage or injury from possible battery leakage.
5. Do not try to recharge batteries not intended to be recharged; they can overheat and
rupture. (Follow battery manufacturer’s directions.)
BACKLIGHT
If the power supply is connected to the DC 6V IN jack, the backlight will always
light on in the display.
6
1
2
1
2
1
2
TO LISTEN TO THE RADIO
OPERATION
1
Press the AM/FM/Power On button to
turn the unit on and select radio.
Repeatedly press the AM/FM/Power
On button to select AM or FM.
3
AUTOMATIC TUNING: Press and hold
the Tune/Skip/Search
button until the frequency in the display
starts to scan, and then release the
button; the tuner will search and then
stop on the next strong station it finds.
Repeat this step until the desired
frequency appears in the display. The
display will revert back to the time
display after five seconds.
l 1 or m 2
2
MANUAL TUNING: Repeatedly press
the Tune/Skip/Search
button to manually advance the
frequency in the display up or down
until the desired frequency appears.
The display will revert back to the time
display after five seconds.
l 1 or m 2
4
Adjust the VOLUME Up/Down buttons
1 as desired.
To turn the unit off, press the STOP
■)/OFF button 2.
(
Antennas
FM: Unravel and extend the FM antenna wire for best reception.
AM: Turn the unit for better AM reception.
7
1
2
3
4
OPERATION (CONTINUED)
RADIO PRESETS–Up to 9 AM and 9 FM
1
Press the AM/FM/Power On button to
turn the unit on and select radio.
Repeatedly press the AM/FM/Power
On button to select AM or FM.
3
Press the PROGRAM button again to
set the station in the selected
memory.
2
Select a station using the Tune/Skip/
Search
PROGRAM button
number will blink in the display. Within
three seconds, press the PRESETS
button
number appears in the display.
l 1 or m 2 button. Press the
3; the preset
4 until the desired memory
4
Repeat steps 2 and 3 to program up to
9 stations in each band, if desired.
TO RECALL: Follow step 1 above.
Repeatedly press the PRESETS
button to select a preset; the station
will automatically be tuned in.
NOTE: See the next page for Automatic Preset Seek.
8
OPERATION (CONTINUED)
2
1
AUTOMATIC PRESET SEEK
To have the unit automatically seek through the radio stations and program the
first 9 strong stations, perform the steps as follows:
1
Press the AM/FM/Power On button to
turn the unit on and select radio.
Repeatedly press the AM/FM/Power
On button to select AM or FM.
INSERTING A CD
1
Slide the CD DOOR OPEN switch to
the right and the CD door will open.
Gently insert a CD onto the spindle
(label side facing forward) until it
clicks. Close the CD door.
2
Press the SEEK button 1; the unit will
then seek through all of the radio stations
and program the first 9 strong stations.
When done, it will stop on the first preset.
Press the PRESETS button
to select a preset station.
2 repeatedly
FAQS: Do I need an adapter to play 3” singles?
No, simply insert the 3” single into the groove.
What is the maximum time for a CD in this unit?
The maximum time is 74 minutes.
9
TO PLAY A CD
1
2
1
2
OPERATION (CONTINUED)
1
With a CD inserted (see previous
page), press the Play/Pause
Power On button to turn the unit on
and select CD; playback will start
automatically.
®p)/CD/
(
3
To skip forward or backward through the
tracks on the disc, press the Tune/Skip/
Search
forward or backward through the tracks
on the disc, press and hold the Tune/
Skip/Search
l 1 or m 2 button. To search
l 1 or m 2 button.
2
If in the Stop mode, press the Play/
Pause (
start playback. TO PAUSE
PLAYBACK, press the Play/Pause
®p)/CD/Power On button again; the
(
elapsed track time will blink in the
display. Press again to resume
playback.
®p)/CD/Power On button to
4
Adjust the VOLUME Up/Down buttons
1 as desired. When the disc is through
playing, it will stop. Press the STOP
(
■)/OFF button 2 to stop the disc before
it is finished. Press the STOP (
button
2 again to turn the unit off.
■)/OFF
NOTES:
• If a disc is inserted incorrectly, dirty, damaged or not present at all, the display will
show, "no disc" for 5 seconds. Then, "no" and the actual time will appear in the display.
• When you press the Tune/Skip/Search
appear for three seconds then revert back to the time display.
• While playing a CD, press the TIME button to show the elapsed time briefly in the
display. When you press the TIME button, the CD playback track's elapsed time will
appear in the display for five seconds and then revert back to the time display.
l or m button, the track elapsed time will
10
OPERATION (CONTINUED)
1
2
2
1
2
1
TO REPEATEDLY PLAY BACK ONE TRACK
1
With a CD inserted (see page 9), press
the Play/Pause
button to turn the unit on and select
CD; playback will start automatically.
®p)/CD/ Power On
(
3
Press the CD MODE button 1 once;
“REPEAT” will appear in the display and
the unit will play the same track over
and over until the STOP (■)/OFF
button
2 is pressed.
2
Press the Tune/Skip/Search l 1 or m
button to select a track to repeat.
2
TO REPEATEDLY PLAY BACK ALL
TRACKS
1
Follow step 1 above. Press the CD
MODE button
will appear in the display and the unit
will play all the tracks on the CD over
and over until the STOP (
button
1 twice; “REPEAT ALL”
■)/OFF
2 is pressed.
TO CANCEL REPEAT MODE,
TO CANCEL REPEAT ALL MODE, press the CD MODE button three
press the CD MODE button four times.
times.
11
OPERATION (CONTINUED)
2
1
3
1
2
1
2
TO PROGRAM THE MEMORY (UP TO 20 TRACKS)
1
With a CD inserted (see page 9), press
the Play/Pause
button to turn the unit on and select CD;
playback will start automatically. Press
the STOP (■)/OFF button 2 to stop
automatic playback.
®p)/CD/ Power On
(
3
Press the PLAY/PAUSE (®p)/CD/
Power On button to begin playback.
The unit will play all the tracks in the
order you programmed them.
2
Press the PROGRAM button 1 once; “P
01” (program number), “00” track number
and the Program indicator will appear in
the display. Select the first track to be
played back using the Tune/Skip/Search
l 2 or m 3 button, then press the
PROGRAM button 1 again. Repeat this
step to program additional tracks, up to
20 tracks.
4
Adjust the VOLUME Up/Down buttons 1
as desired. When the disc is through
playing, it will stop. Press the STOP
■)/OFF button 2 to stop the disc before
(
it is finished.
NOTES:
• To skip forward or backward through the programs, press the Tune/Skip/
Search
• Programming is the ability to preselect the order in which a series of tracks will
be played.
FAQ: How do I clear the memory and exit the Program Playback mode?
l or m button.
While in the Program Stop mode, press the STOP (■)/OFF button; the
"PROGRAM" indicator will disappear from the display.
12
1
2
OPERATION (CONTINUED)
RANDOM PLAYBACK
1
To play the tracks on the CD in a
random order, while in the Stop mode,
press the CD MODE button three
times; “RANDOM” will appear in the
display.
TO CANCEL RANDOM MODE, press the CD MODE button twice.
TO CANCEL REPEAT ALL RANDOM MODE, press the CD MODE button once.
TO STOP PLAYBACK, press the STOP (■)/OFF button.
HEADPHONES Jack
For private listening, plug headphones (not supplied) into the Headphones jack on the rear of
the unit. When the headphones are plugged in, the speakers will be muted.
LINE IN Jack
By using a home audio connection cable (not included), you can listen to an external audio unit
through this unit’s speakers. Before making any connections, turn off the power to all equipment.
Press the AM/FM/Power On button or the PLAY/PAUSE (®p)/Power On button to turn the unit
to CD or Radio mode. Plug a connection cable (not included) between the LINE OUT jack on
the external audio unit and this unit's LINE IN jack (rear of the unit). (Do not connect it to this
unit's Headphone jack.) Then the unit will automatically turn to the AUX mode and the "AUX"
indicator will appear in the display. Turn on the external audio unit and start playback; the
external unit's output sound will be heard through this unit's speakers. Press the Volume
Up/Down button to adjust the volume level as desired.
To turn the unit off, remove the plug from the LINE IN jack, then press the STOP (
NOTE: If you are in Radio/CD mode, when you connect an external unit to the LINE IN jack, this
unit will automatically switch to AUX mode. If you remove the plug from the LINE IN jack, the unit
will resume to the mode it was in before the external unit was connected.
2
Press the PLAY/PAUSE (®p)/CD/
Power On button
randomly play each track on the CD
and then stop. If you want to randomly
playback the tracks repeatedly, press
the CD MODE button
“REPEAT ALL RANDOM” will appear
in the display.
1; the unit will
2 once more;
■)/OFF button.
13
OPERATION (CONTINUED)
2
1
TO SET OR RESET THE ACTUAL TIME
1
With the power off, press the TIME
button; the time will blink.
3
2
Press the MINUTE button 1 to set
the present minute and the HOUR
button
Make sure to set the correct AM/PM
setting.
2 to set the present hour.
Press the TIME button (or wait
approx. 15 seconds) and the time will
be set.
14
OPERATION (CONTINUED)
1
2
1
2
1
2
1
2
3
4
TO SET OR RESET THE ALARM TIME
1
With the power off, press the desired ALARM
1 1 or ALARM 2 2 button; the Alarm 1 or
Alarm 2 time and settings will appear.
3
Repeatedly press the ALARM 1 1 or ALARM
2 button to select alarm off, alarm on for
2
buzzer, radio or CD.
NOTE: Make sure the corresponding
indicator (BUZZER/CD/RADIO) appears in
the display.
2
Press and hold the desired ALARM 1 1 or
ALARM 2 2 button; the alarm time will blink.
Press the MINUTE button
minute and the HOUR button 4 to set the
alarm hour. Make sure to set the correct
AM/PM setting. Press the ALARM 1
ALARM 2 2 button again (or wait approx. 15
seconds); the alarm time will stop blinking.
3 to set the alarm
1 or
4
If set to CD, within 5 seconds, set the track number
using the Tune/Skip/Search
the alarm time is reached, the unit will start playback
on the track that you selected and the tracks following
it, then stop.
NOTES:
• When you have selected a track number, after five
seconds, the track number will be set and the
actual time will appear in the display again.
• If the selected track is not available (i.e. there are a
total of 10 tracks on the disc but you have selected
track 11), when the alarm time is reached,
playback will start from the first track.
If set to Radio, within 5 seconds, set the band (AM or
FM) and the frequency using the Tune/Skip/Search
or m 2 button. When the alarm time is reached, the
1
unit will turn on the band (AM or FM) and the
frequency that you selected.
NOTE: When you have selected the radio band and
frequency, after 5 seconds, the radio frequency will be
set and the actual time will appear in the display again.
l 1 or m2 button. When
l
SEE NEXT PAGE FOR IMPORTANT ALARM NOTES.
15
OPERATION (CONTINUED)
NOTES:
• It is not necessary to set the volume level for the alarm. When the alarm
time is reached, the alarm volume level will be set to the default (Medium
Level) and it will increase one step every five seconds continuously until the
maximum volume level is reached.
• When the actual time matches the selected preset alarm time(s),
Radio or Buzzer
shut off. If set to CD, the unit will only play the tracks on the CD and then
shut off. If you select a starting track for the alarm, the unit will only playback
the selected track and the tracks following it and then shut off.
TO SHUT OFF THE ALARM, see TO SHUT THE ALARM OFF section on
•
the next page.
• While the alarm is sounding, if the other alarm reaches the alarm time, the
first alarm will stop sounding and the second alarm will start sounding.
• Make sure you have disconnected the headphones from the Headphones
jack (rear of the unit) and disconnected the audio cable from the LINE IN
jack (rear of the unit); otherwise, there will be no sound when the actual time
matches the preset alarm time.
, the unit will automatically turn on for 20 minutes and then
if set to
16
OPERATION (CONTINUED)
1
2
TO SHUT THE ALARM OFF
1
SNOOZE AND SLEEP
1
To shut the alarm off, press the desired ALARM 1 1 or
ALARM 2 2 button and the alarm time will be reset for
the next day. Press the desired ALARM 1
2 2 button repeatedly until the alarm time and the
ALARM 1 or ALARM 2 indicator disappears from the
display to turn off the alarm and not set it for the next
day.
SNOOZE: While the alarm is sounding, press the
SNOOZE/SLEEP button; the SNOOZE indicator will appear in the
display. Also, "10" will appear in the display for five seconds and
then revert back to the actual time. The alarm will turn back on
automatically ten minutes later.
press and hold the SNOOZE/SLEEP button. Keep holding the
button for approx. one second, "10" will appear in the display
indicating the alarm will turn back on after 10 minutes. Continue
holding the button for one more second, "15" will appear in the
display indicating the alarm will turn back on after 15 minutes.
Continue holding the button to set the SNOOZE time to "20", "25",
"30", etc., up to "60". Please note that once you release the button,
the time shown on the display will be the SNOOZE time and the
alarm will turn back on according to the SNOOZE time set.
To cancel the SNOOZE function, press the STOP (■)/OFF button
once; the SNOOZE indicator will disappear from the display.
SLEEP: With the unit in the CD or Radio mode, press the
SNOOZE/SLEEP button twice; "10" will appear in the display for
five seconds which indicates the unit will turn off after 10 minutes.
Repeatedly press the SNOOZE/SLEEP button to select the
SLEEP time, up to 60 minutes (i.e. , "20"–turns off automatically
after 20 minutes, "30"–turns off automatically after 30 minutes,
etc.). After 5 seconds, the SLEEP time will disappear from the
display. To view the remaining SLEEP time, press the
SNOOZE/SLEEP button once.
function, repeatedly press the SNOOZE/SLEEP button until "- -"
appears in the display. After five seconds, the actual time will
appear again and the SLEEP indicator will disappear from the
display.
OR While the alarm is sounding,
NOTE: To cancel the SLEEP
1 or ALARM
NOTE:
DISPLAY DIM BUTTON
1
Press the Display DIM button to adjust the dimmer of
the display. If the display is too dim, press the Display
DIM button for a brighter display. Press the Display DIM
button again to resume to a less bright display.
17
CARE AND MAINTENANCE
Caring for Compact Discs
• Treat the disc carefully. Handle the disc only
by its edges. Never allow your fingers to come
in contact with the shiny, unprinted side of the
disc.
• Do not attach adhesive tape, stickers, etc. to
the disc label.
• Clean the disc periodically with a soft, lint-free, dry cloth. Never use detergents
or abrasive cleaners to clean the disc. If necessary, use a CD cleaning kit.
• If a disc skips or gets stuck on a section of the disc, it is probably dirty or
damaged (scratched).
• When cleaning the disc, wipe in straight lines from the center of the disc to the
outer edge of the disc. Never wipe in circular motions.
• This unit is designed to play only discs bearing the identification
logo as shown here. Other discs may not conform to the CD
standard and may not play properly.
• Discs should be stored in their cases after each use to avoid
damage.
• Do not expose discs to direct sunlight, high humidity, high temperatures or dust,
etc. Prolonged exposure or extreme temperatures can warp the disc.
• Do not stick or write anything on either side of the disc. Sharp writing
instruments, or the ink, may damage the surface.
Cleaning the Unit
• To prevent fire or shock hazard, disconnect your unit from the AC power source
when cleaning.
• The finish on your unit may be cleaned with a dust cloth and cared for as other
furniture. Use caution when cleaning and wiping the plastic parts.
• Mild soap and a damp cloth may be used on the front panel.
18
TROUBLESHOOTING GUIDE
If you experience a problem with this unit, check the chart below before calling
for service.
SYMPTOM CAUSE SOLUTION
Unit will not AC adapter is not Check the AC adapter
turn on. connected. connection.
Disc will not play. CD compartment Close CD compartment
door not closed. door.
Disc inserted Reinsert disc correctly.
incorrectly.
Dirty or defective CD. Try another disc.
Moisture Wipe disc with soft cloth.
condensation on disc.
No sound. Volume setting is Increase volume.
set to minimum.
Defective disc. Try another disc.
Erratic playback. Dirty or defective Clean or replace disc.
disc.
Time reset to “12:00”. Batteries connected Check the batteries.
improperly, not connected or dead.
Clock not set. Set the clock.
Alarm does not Alarm is not activated Set and activate alarm as
turn on. or set properly. described on page 15.
Clock is not set. Set the clock.
AM or FM, no sound. Power is not on. Press AM/FM/Power On
button to turn the unit on.
Volume setting is Increase volume.
set to minimum.
19
SPECIFICATIONS
AUDIO
Frequency Range (AM)..................................................520–1710KHz
Frequency Range (FM)...................................................87.5–108MHz
CD SECTION:
Disc Diameter................................................................4.72” (120mm)
3.15” (80mm) Single CD
Optical Source.....................................................Semiconductor Laser
Wavelength ................................................................................780nm
GENERAL
Power Supply......................................DC IN Jack 6V, Center Positive
Battery Backup ...................................... 2 x 1.5V “AAA” size batteries
FOR ADDITIONAL SET-UP OR OPERATING ASSISTANCE, PLEASE VISIT
OUR WEB SITE AT
WWW.MEMOREXELECTRONICS.COM
OR CONTACT CUSTOMER SERVICE AT (954) 660-7100.
PLEASE KEEP ALL PACKAGING MATERIAL FOR AT LEAST 90 DAYS IN
CASE YOU NEED TO RETURN THIS PRODUCT TO YOUR PLACE OF
PURCHASE OR TO MEMOREX.
FOR PARTS AND ACCESSORIES, CONTACT FOX INTERNATIONAL AT
1-800-321-6993.
20
Memcorp, Inc.
Weston, FL
Printed in Hong Kong
Visit our website at www.memorexelectronics.com
Loading...