MC2864
User’s Guide
CD PLAYER, DUAL ALARM CLOCK,
STEREO AM/FM RADIO WITH DIGITAL
READOUT AND CALENDAR
Before operating this product,
please read these instructions completely.
SAFETY PRECAUTIONS
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOTREMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL. This Caution Marking and Rating Label are located at the bottom enclosure of the unit.
The lightning flash with arrowhead symbol within an
equilateral triangle is intended to alert the user to the
presence of uninsulated dangerous voltage within the
product’s enclosure that may be of sufficient magnitude to
constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is
intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in the
literature accompanying the appliance.
Invisible and hazardous laser radiation when open and
interlock failed or defeated.
FCC WARNING:
This equipment may generate or use radio frequency energy. Changes or
modifications to this equipment may cause harmful interference unless the
modifications are expressly approved in the instruction manual. The user could
lose the authority to operate this equipment if an unauthorized change or
modification is made.
Avoid direct exposure to beam.
LASER SAFETY: This unit employs a laser. Only qualified service personnel
should attempt to service this device due to possible eye injury.
CAUTION: USE OF CONTROLS, ADJUSTMENTS OR PERFORMANCE
PROCEDURE HEREIN MAY RESULT IN HAZARDOUS RADIATION
EXPOSURE.
SURGE PROTECTORS:
It is recommended to use a surge protector for AC connection. Lightning and
power surges ARE NOT covered under warranty for this product.
1
INFORMATION:
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
• Consult the dealer or an experienced radio/TV technician for help.
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
ATTENTION:
POUR ÉVITER LES CHOC ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE
LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISES ET POUSSER
JUSQU’AU FOND.
IMPORTANT SAFETY INSTRUCTIONS
Before using the unit, be sure to read all operating
instructions carefully. Please note that these are general
precautions and may not pertain to your unit. For
example, this unit may not have the capability to be
connected to an outdoor antenna.
1. READ INSTRUCTIONS
All the safety and operating instructions should be read
before the product is operated.
2. RETAIN INSTRUCTIONS
The safety and operating instructions should be retained
for future reference.
3. HEED WARNINGS
All warnings on the product and in the operating
instructions should be adhered to.
4. FOLLOW INSTRUCTIONS
All operating and use instructions should be followed.
5. CLEANING
Unplug this product from the wall outlet before cleaning.
Do not use liquid cleaners or aerosol cleaners. Use a dry
cloth for cleaning.
6. ATTACHMENTS
Do not use attachments not recommended by the
product's manufacturer as they may cause hazards.
7. WATER AND MOISTURE
Do not use this product near water–for example: near a
bathtub, washbowl, kitchen sink or laundry tub; in a wet
basement; or near a swimming pool.
8. ACCESSORIES
Do not place this product on an unstable cart, stand,
tripod, bracket or table. The product may fall, causing
serious injury and serious damage to the product. Use
only with a cart, stand, tripod, bracket or table
recommended by the manufacturer or sold with the
product. Any mounting of the product should follow the
manufacturer’s instructions, and should use a mounting
accessory recommended by the manufacturer.
8A. An appliance and cart combination should
be moved with care. Quick stops,
excessive force and uneven surfaces may
cause the appliance and cart combination
to overturn.
9. VENTILATION
Slots and openings in the cabinet and in the back or
bottom are provided for ventilation, to ensure reliable
operation of the product and to protect it from
overheating. These openings must not be blocked or
covered. The openings should never be blocked by
placing the product on a bed, sofa, rug or other similar
surface. This product should never be placed near or
over a radiator or heat source.
be placed in a built-in installation such as a bookcase or
rack unless proper ventilation is provided or the
This product should not
2
IMPORTANT SAFETY INSTRUCTIONS
manufacturer's instructions have been adhered to.
0. POWER SOURCES
1
his product should be operated only from the type of
T
power source indicated on the marking label. If you are
not sure of the type of power supply to your home,
consult your appliance dealer or local power company.
For products intended to operate from battery power, or
ther sources, refer to the operating instructions.
o
11. GROUNDING OR POLARIZATION
his product is equipped with a polarized alternating-
T
current line plug (a plug having one blade wider than the
other). This plug will fit into the power outlet only one
way. This is a safety feature. If you are unable to insert
the plug fully into the outlet, try reversing the plug. If the
plug should still fail to fit, contact your electrician to
replace your obsolete outlet. Do not defeat the safety
purpose of the polarized plug.
12. POWER-CORD PROTECTION
Power-supply cords should be routed so that they are
not likely to be walked on or pinched by items placed
upon or against them, paying particular attention to
cords at plugs, convenience receptacles, and the point
where they exit from the appliance.
13. LIGHTNING
To protect your product from a lightning storm, or when
it is left unattended and unused for long periods of time,
unplug it from the wall outlet and disconnect the antenna
or cable system. This will prevent damage to the product
due to lightning and power-line surges.
14. POWER LINES
An outside antenna system should not be located in the
vicinity of overhead power lines or other electric light or
power circuits, or where it can fall into such power lines
or circuits. When installing an outside antenna system,
extreme care should be taken to keep from touching
such power lines or circuits as contact with them might
be fatal.
15. OVERLOADING
Do not overload wall outlets and extension cords as this
can result in a risk of fire or electric shock.
16. OBJECT AND LIQUID ENTRY
Never push objects of any kind into this product through
openings as they may touch dangerous voltage points
or short out parts that could result in fire or electric
shock. Never spill or spray any type of liquid on the
product.
17. SERVICING
Do not attempt to service this product yourself as
opening or removing covers may expose you to
dangerous voltage or other hazards. Refer all servicing
to qualified service personnel.
18. REPLACEMENT PARTS
When replacement parts are required, be sure the
service technician uses replacement parts specified by
the manufacturer or those that have the same
characteristics as the original part. Unauthorized
substitutions may result in fire, electric shock or other
hazards.
19. SAFETY CHECK
Upon completion of any service or repairs to this
product, ask the service technician to perform safety
hecks to determine that the product is in proper
c
perating condition.
o
20. WALL OR CEILING MOUNTING
The product should be mounted to a wall or ceiling only
as recommended by the manufacturer.
21. DAMAGE REQUIRING SERVICE
nplug the product from the wall outlet and refer
U
servicing to qualified service personnel under the
ollowing conditions:
f
a. When the power-supply cord or plug is damaged.
b. If liquid has been spilled or objects have fallen into the
product.
c. If the product has been exposed to rain or water.
d. If the product does not operate normally by following the
operating instructions. Adjust only those controls that are
covered by the operating instructions, as an adjustment
of other controls may result in damage and will often
require extensive work by a qualified technician to
restore the product to its normal operation.
e. If the product has been dropped or the cabinet has been
damaged.
f. When the product exhibits a distinct change in
performance–this indicates a need for service.
22. HEAT
The product should be situated away from heat sources
such as radiators, heat registers, stoves or other
products (including amplifiers) that produce heat.
23. NOTE TO CATV SYSTEM INSTALLER
This reminder is provided to call the CATV system
installer's attention to Article 820-40 of the NEC that
provides guidelines for proper grounding and, in
particular, specifies that the cable ground shall be
connected to the grounding system of the building, as
close to the point of cable entry as practical.
24. OUTDOOR ANTENNA GROUNDING
If an outside antenna is connected to the product, be
sure the antenna system is grounded so as to provide
some protection against voltage surges and built-up
static charges. Section 810 of the National Electric
Code, ANSI/NFPA 70, provides information with respect
to proper grounding of the mast and supporting
structure, grounding of the lead-in wire to an antenna
discharge product, size of grounding conductors,
location of antenna discharge product, connection to
grounding electrodes and requirements for grounding
electrodes.
EXAMPLE OF ANTENNA GROUNDING AS PER
NATIONAL ELECTRICAL CODE
3
Dear Customer:
A
S
S
O
C
I
A
T
I
O
N
EST. 1924
E
L
E
C
T
R
O
N
I
C
I
N
D
U
S
T
R
I
E
S
EIA
We
LISTENING
For A Lifetime
Want You
Selecting fine audio equipment such as the unit you’ve just purchased is only the start of your
musical enjoyment. Now it’s time to consider how you can maximize the fun and excitement
your equipment offers. This manufacturer and the Electronic Industries Association’s
Consumer Electronics Group want you to get the most out of your equipment by playing it at a
safe level. One that lets the sound come through loud and clear without annoying blaring or
distortion—and, most importantly, without affecting your sensitive hearing.
Sound can be deceiving. Over time your hearing “comfort level” adapts to higher volumes of
sound. So what sounds “normal” can actually be loud and harmful to your hearing. Guard
against this by setting your equipment at a safe level BEFORE your hearing adapts.
To establish a safe level:
• Start your volume control at a low setting.
• Slowly increase the sound until you can hear it comfortably and clearly, and without distortion.
Once you have established a comfortable sound level:
• Set the dial and leave it there.
Taking a minute to do this now will help to prevent hearing damage or loss in the future. After
all, we want you listening for a lifetime.
We Want You Listening For A Lifetime
Used wisely, your new sound equipment will provide a lifetime of fun and enjoyment. Since
hearing damage from loud noise is often undetectable until it is too late, this manufacturer and
the Electronic Industries Association’s Consumer Electronics Group recommend you avoid
prolonged exposure to excessive noise. This list of sound levels is included for your protection.
Decibel
Level
Example
30 Quiet library, soft whispers
40 Living room, refrigerator, bedroom away from traffic
50 Light traffic, normal conversation, quiet office
60 Air conditioner at 20 feet, sewing machine
70 Vacuum cleaner, hair dryer, noisy restaurant
80 Average city traffic, garbage disposals, alarm clock at two feet
THE FOLLOWING NOISES CAN BE DANGEROUS UNDER CONSTANT EXPOSURE:
90 Subway, motorcycle, truck traffic, lawn mower
100 Garbage truck, chain saw, pneumatic drill
120 Rock band concert in front of speakers, thunderclap
140 Gunshot blast, jet engine
180 Rocket launching pad
Information courtesy of the Deafness Research Foundation.
4
2423 25 26 28 29 30 3127
12 1310 11 14 15 17
2
20 21 2216 1918
1 4 5 6 7 8 93
FRONT-LEFT
REAR-RIGHT
LOCATION OF CONTROLS
1. FUNCTION Button
2. TIME Button
3. CD Compartment
4. ALARM 1 Button
5. STOP (
6. SKIP/SEARCH
7. Play/Pause
8. SKIP/SEARCH
9. OPEN Button
10. DIMMER Switch
11. VOLUME Control
12. POWER Button
13. REPEAT Button
14. Left Speaker
15. ALARM MODE Button
16. SLEEP Button
17. Display
18. SNOOZE Button
19. ALARM 2 Button
20. Alarm 2 Display
21. Alarm 1 Display
22. PROGRAM Button
23. Right Speaker
24. TUNING Control
25. Band Switch
26. NATURE SOUND Switch
27. Battery Door/
28. AUX IN Jack
29. Headphones Jack
30. AC Cord
31. FM Antenna Wire
■) Button
l Button
®p) Button
(
m Button
(LOW/HIGH)
(AM/FM/FM ST.)
Compartment (Bottom
of Unit)
[Door Part No. 02100286400-0000*]
*Consumer Replaceable Part
(See page 23 to order.)
5
INSTALLATION
+–
+–
AC Plug
AC Outlet
AC CONNECTION
CAUTION: TO PREVENT ELECTRIC SHOCK,
MATCH WIDE BLADE OF PLUG TO WIDE
SLOT, FULLY INSERT.
Unravel the AC cord and connect it to a
conveniently located AC outlet having 120V and
60Hz only. “12:00” will appear in the display.
NOTE: If the AC plug does not fit into a
nonpolarized outlet, do not file or cut the wide
blade.
INSERTING BATTERIES
Two (2) “AAA” size batteries should be used to provide a backup for the clock and
alarm time for this unit as follows:
1. Open the Battery Compartment door by pushing in on the tab, then removing
the Battery Compartment door.
2. Insert two (2) “AAA” batteries as shown.
Alkaline batteries are recommended for the
longest playing time.
3. Replace the Battery Compartment door.
NOTES:
• The batteries are used to backup the clock
and alarm time when the AC plug is
disconnected or there is a power failure.
• If the batteries are low or no batteries are
inserted, "BATT. LOW" will blink in the
display.
Follow these precautions when using batteries in this device:
1. Use only the size and type of batteries specified.
2. Be sure to follow the correct polarity when installing the batteries as indicated in the
battery compartment. Reversed batteries may cause damage to the device.
3. Do not mix different types of batteries together (e.g. Alkaline, Rechargeable and
Carbon-zinc) or old batteries with fresh ones.
4. If the device is not to be used for a long period of time, remove the batteries to
prevent damage or injury from possible battery leakage.
5. Do not try to recharge batteries not intended to be recharged; they can overheat and
rupture. (Follow battery manufacturer’s directions.)
BATTERY PRECAUTIONS
6
2
1
1
2
2
1
TO LISTEN TO THE RADIO
OPERATION
1
Press the POWER button 1 to turn the
unit on. Repeatedly press the
FUNCTION button
radio; RADIO will appear in the display.
2 to select the
3
The time will appear on the display
when listening to the radio. To view the
station, press the TIME button; the
tuned station will appear for approx. 10
seconds and then revert back to the
time display.
2
Slide the Band switch 1 to select AM,
FM or FM STEREO.
Tune a station by turning the TUNING
control
signal is received the FM Stereo icon
will light.
2. When a strong FM stereo
4
Adjust the volume using the VOLUME
control
1.
To turn the unit off, press the POWER
2.
button
Antennas
FM: Unravel and extend the FM antenna wire for best reception.
AM: Turn the unit for better AM reception.
7
OPERATION (CONTINUED)
2
1
TO LISTEN TO THE NATURE SOUNDS
1
Press the POWER button 1 to turn the
unit on. Repeatedly press the
FUNCTION button
sounds; “NS” will appear in the display.
2 to select nature
3
Adjust the volume using the VOLUME
control.
2
Slide the NATURE SOUND switch to
the desired position (SONGBIRDS,
OCEAN SURF, GENTLE RAIN,
MOUNTAIN STREAM).
4
To turn the unit off, press the POWER
button.
: A good use of this feature is to use it in conjunction with the Sleep feature
Note
on page 20.
8
1
2
TO PLAY A CD
OPERATION (CONTINUED)
1
Press the OPEN button 1 and gently
insert a CD onto the spindle (label
side facing up) until it clicks. Close the
CD door. Press the POWER button
to turn the unit on.
3
Press the Play/Pause(®p) button to
start playback; “PLAY” will appear in
the display.
2
Repeatedly press the FUNCTION
button to select CD; “CD” will appear in
the display; the total number of tracks
will appear in the display.
2
4
TO PAUSE PLAYBACK, press the
Play/Pause (
“PAUSE” will appear in the display.
Press again to resume playback.
®p) button again;
CONTINUED ON THE NEXT PAGE
9
1
2
1
2
OPERATION (CONTINUED)
5
To skip to the beginning of the current
track/previous or next track on the disc,
press the Skip/ Search
button. To search forward or backward
through the tracks on the disc, press and
hold the Skip/Search
button.
l 1 or m 2
l 1 or m 2
7
Adjust the volume using the VOLUME
control.
6
The time will appear on the display
when listening to the CD. To view the
playing track, press the TIME button;
the track number will appear for
approx. 10 seconds and then revert
back to the time display.
8
When the disc is through playing, it will
stop. Press the STOP (
stop the disc before it is finished.
Press the POWER button
unit off.
■) button 1 to
2 to turn the
NOTES:
• If a disc is inserted incorrectly, dirty, damaged or not present at all, the display will
show, "--" will blink in the display and then “no” will appear in the display for approx. 10
seconds. Then, the actual time will appear in the display.
• When you press the SKIP/SEARCH
approx. 10 seconds then revert back to the time display.
• If the CD door is opened, "OP" will appear for approx. 10 seconds on the display.
l or m button, the track number will appear for
10
OPERATION (CONTINUED)
2
1
2
3
1
1
2
1
2
TO REPEATEDLY PLAY BACK ONE TRACK
1
With a CD inserted, press the POWER
button
Repeatedly press the FUNCTION
button
in the display; the total number of
tracks will appear in the display.
1 to turn the unit on.
2 to select CD; “CD” will appear
3
Press the REPEAT button 1 once;
“REPEAT” will appear in the display and
the unit will play the same track over
and over until the STOP (
pressed.
■) button 2 is
2
Press the Play/Pause(®p) button 1
to start playback; “PLAY” will appear in
the display. Press the SKIP/SEARCH
l 2 or m 3 button to select a track to
repeat.
TO REPEATEDLY PLAY BACK ALL
TRACKS
1
Follow steps 1 and 2 above, but do not
select a specific track. Press the
REPEAT button
ALL” will appear in the display and the
unit will play all the tracks on the CD
over and over until the STOP (■) button
2 is pressed.
1 twice; “REPEAT
TO CANCEL REPEAT MODE,
TO CANCEL REPEAT ALL MODE, press the REPEAT button once.
press the REPEAT button twice.
11
OPERATION (CONTINUED)
2
1
2
3
1
1
2
TO PROGRAM THE MEMORY (UP TO 32 TRACKS)
1
With a CD inserted, press the POWER
button
Repeatedly press the FUNCTION
button
in the display; the total number of
tracks will appear in the display.
1 to turn the unit on.
2 to select CD; “CD” will appear
3
Press the PLAY/PAUSE (®p) button
to begin playback. The unit will play all
the tracks in the order you
programmed them; both “PROG” and
“PLAY” will appear in the display.
2
Press the PROGRAM button 1 once;
“PROG” will blink and “1” (program
number) will appear in the display. Select
the first track to be played back using the
SKIP/SEARCH
("PROG" will not blink while the track is
being selected), then press the
PROGRAM button
step to program additional tracks, up to
32 tracks.
l 2 or m 3 button
1 again. Repeat this
4
When the disc is through playing, it will
stop. Press the STOP (
stop the disc before it is finished.
Press the POWER button
unit off.
■) button 1 to
2 to turn the
NOTES:
• To skip forward or backward through the programs, press the Skip/Search l
or m button.
• Programming is the ability to preselect the order in which a series of tracks will
be played.
FAQ: How do I clear the memory and exit the Program Playback mode?
While in the Program Stop mode, press the STOP (■) button; "PROG"
will disappear from the display.
12
OPERATION
2
1
TO LISTEN TO AN EXTERNAL UNIT
1
Press the POWER button 1 to turn the
unit on. Repeatedly press the
FUNCTION button
radio; RADIO will appear in the display.
2 to select the
3
The sound will be heard through this
unit’s speakers. Adjust the volume
using the VOLUME control.
2
Connect the external unit’s AUDIO
OUT jack to the AUX IN jack on the
rear of this unit via an audio cable (not
included). Turn on the external unit and
start playback.
NOTES:
• When you are done listening to
the external unit, disconnect the
audio cable from the AUX IN
jack (rear of unit).
• If the external unit's cable is
disconnected, this unit will turn
off automatically.
• To turn on the unit again
disconnect the audio cable and
press the POWER button.
HEADPHONES Jack
For private listening, plug headphones (not supplied) into the Headphones
jack on the rear of the unit. When the headphones are plugged in, the
speakers will be muted.
13
OPERATION (CONTINUED)
1
2
3
1
2
3
1
2
3
TO SET OR RESET THE ACTUAL TIME, YEAR AND DATE
1
With the power off, press and hold
the TIME button; the hour digits will
blink. Release the TIME button.
3
2
Within five seconds, press the
SKIP/SEARCH
set the present hour. Make sure to
set the correct AM/PM setting. When
done, press the TIME button
again; the minute digits will blink.
l 1 or m 2 button to
4
3
Within five seconds, press the
SKIP/SEARCH
to set the present minute. When
done, press the TIME button
again; the year will blink.
l 1 or m 2 button
CONTINUED ON THE NEXT PAGE
Within five seconds, press the
SKIP/SEARCH
to set the present year. When
done, press the TIME button 3
3
again; the month will blink.
14
l 1 or m 2 button
1
2
3
1
2
3
OPERATION (CONTINUED)
5
Within five seconds, press the
SKIP/SEARCH l 1 or m 2 button
to set the present month. When
done, press the TIME button 3
again; the date will blink.
TIME BUTTON
1
6
Within five seconds, press the
SKIP/SEARCH l 1 or m 2 button
to set the present date. When
done, press the TIME button 3
again; the time will then be set.
While the unit is off, press the
TIME button to view the year,
month and date in the Alarm 1 and
2 displays. After six seconds, the
displays will revert back to showing
the Alarm 1 and 2 settings (alarm
time and type).
15
OPERATION (CONTINUED)
1
2
4
3
3
4
2
1
2
1
1
2
4
3
TO SET OR RESET THE ALARM TIME
1
With the power off, press the desired
ALARM 1
hour and “AL1”/“AL2” will blink for five
seconds. "PM" will also blink if the time
is in the p.m.
1 or ALARM 2 2 button; the
3
Within five seconds, press the
SKIP/SEARCH
set the alarm minute. When done,
press the ALARM 1
button again; the alarm’s function and
“AL1”/“AL2” will blink.
l 1 or m 2 button to
3 or ALARM 2 4
2
Within five seconds, press the
SKIP/SEARCH
the alarm hour. Make sure to set the
correct AM/PM setting. When done, press
the ALARM 1
again; the alarm’s minute digits and
“AL1”/“AL2” will blink for five seconds.
l 1 or m 2 button to set
3 or ALARM 2 4 button
4a
TO SET TO CD:
Within five seconds, press the
SKIP/SEARCH
select CD. Press the ALARM 1
ALARM 2
track; "ch" will appear, "1" & "ALR1" will
blink. Press the SKIP/SEARCH
m 4 button to select the track you
would like to wake to. Make sure the
volume is set as desired. Continue to
Step 5.
l 3 or m 4 button to
1 or
2 button again to set the
l 3 or
CONTINUED ON THE NEXT PAGE
16
1
2
1
2
3
OPERATION (CONTINUED)
1
2
2
1
4b
TO SET TO RADIO:
Within five seconds, press the
SKIP/SEARCH
select RADIO. Make sure the desired
band and station are set, and the
volume is set as desired. Continue to
Step 5.
l 1 or m 2 button to
4d
4c
TO SET TO NATURE SOUNDS:
Within five seconds, press the
SKIP/SEARCH
select NATURE SOUND. Make sure
the NATURE SOUND switch
the desired position and the volume is
set as desired. Continue to Step 5.
l 1 or m 2 button to
3 is set to
5
TO SET TO BUZZER:
Within five seconds, press the
SKIP/SEARCH
select BUZZER. Make sure the volume
is set as desired. Continue to Step 5.
l 1 or m 2 button to
CONTINUED ON THE NEXT P
Press the ALARM 1 1 or ALARM 2 2
button again; the alarm indicator and
the Wake Day indicator (“MON to FRI”,
“SAT & SUN” or “MON to SUN”) will
blink.
AGE
17
OPERATION (CONTINUED)
1
2
2
1
6
Press the SKIP/SEARCH l 1 or m 2
button to select the desired Wake Day
indicator (i.e., to set the alarm to go off
only from Monday to Friday, select
“MON to FRI”.)
8
NOTES:
• When the actual time matches the selected preset alarm time(s), if set to Radio,
Nature Sounds or Buzzer, the unit will automatically turn on for 60 minutes and then
shut off. If set to CD, without selecting a starting track, the unit will start playback on
the first track and play up to 60 minutes. If you select a starting track, the unit will only
playback the selected track and the tracks following it and then stop playback, up to 60
minutes. If you select a starting track higher than the track numbers on the CD, the unit
will start playback on the first track and play up to 60 minutes.
TO SHUT OFF THE ALARM, see TO SHUT THE ALARM OFF section on the next
•
page.
• While the alarm is sounding, if the other alarm reaches the alarm time, the first alarm
will stop sounding and the second alarm will start sounding.
• Make sure you have disconnected the headphones from the Headphones jack (rear of
the unit) and disconnected the audio cable from the AUX IN jack (rear of the unit);
otherwise, there will be no sound when the actual time matches the preset alarm time.
7
Press the ALARM 1 1 or ALARM 2 2
button again and the alarm will be set.
TO ACTIVATE ONE OR BOTH
ALARMS:
button once to activate Alarm 1, twice
to activate Alarm 2, three times to
activate both alarms and four times to
deactivate both alarms.
Press the ALARM MODE
18
OPERATION (CONTINUED)
2
1
TO SHUT THE ALARM OFF
1
SNOOZE
To shut the alarm off, press the POWER button
1 and the alarm time will be reset for the next
day. Press the ALARM MODE button
repeatedly until the ALARM 1 or ALARM 2
indicator disappears from the display to turn off
the alarm and not set it for the next day.
2
1
DIMMER BUTTON
1
The alarm can be temporarily turned off
manually by pressing the SNOOZE button
(“SNOOZE” & “AL1”/“AL2” will blink in the
display); the alarm will turn back on
automatically nine minutes later. It can be
repeated for one hour.
Slide the DIMMER switch to the LOW or HIGH position
to adjust the dimmer of the display.
19
1
2
3
4
OPERATION (CONTINUED)
TO ACTIVATE THE SLEEP FUNCTION
1
Press the POWER button to turn the
unit on. Tune the desired radio station,
select a nature sound or insert a CD as
previously instructed.
3
Select a desired sleep time (1 to 99
minutes) using the SKIP/SEARCH
or m 2 button. Press the SLEEP
1
button
3 to confirm the time setting;
“SLEEP” will appear in the display.
When the time setting is reached, the
unit will turn off. Press the POWER
button
cancel the sleep timer; the unit will turn
off.
NOTE: If you press the SLEEP button
again during Sleep mode, the sleep
time will count from the beginning
again.
4 (or SNOOZE button) to
2
Press the SLEEP button and the sleep
time will appear in the display.
l
20
CARE AND MAINTENANCE
Caring for Compact Discs
• Treat the disc carefully. Handle the disc only
by its edges. Never allow your fingers to come
in contact with the shiny, unprinted side of the
disc.
• Do not attach adhesive tape, stickers, etc. to
the disc label.
• Clean the disc periodically with a soft, lint-free, dry cloth. Never use detergents
or abrasive cleaners to clean the disc. If necessary, use a CD cleaning kit.
• If a disc skips or gets stuck on a section of the disc, it is probably dirty or
damaged (scratched).
• When cleaning the disc, wipe in straight lines from the center of the disc to the
outer edge of the disc. Never wipe in circular motions.
• This unit is designed to play only discs bearing the identification
logo as shown here. Other discs may not conform to the CD
standard and may not play properly.
• Discs should be stored in their cases after each use to avoid
damage.
• Do not expose discs to direct sunlight, high humidity, high temperatures or dust,
etc. Prolonged exposure or extreme temperatures can warp the disc.
• Do not stick or write anything on either side of the disc. Sharp writing
instruments, or the ink, may damage the surface.
Cleaning the Unit
• To prevent fire or shock hazard, disconnect your unit from the AC power source
when cleaning.
• The finish on your unit may be cleaned with a dust cloth and cared for as other
furniture. Use caution when cleaning and wiping the plastic parts.
• Mild soap and a damp cloth may be used on the front panel.
21
TROUBLESHOOTING GUIDE
If you experience a problem with this unit, check the chart below before calling
for service.
SYMPTOM CAUSE SOLUTION
Unit will not AC cord not Check AC cord
turn on. connected. connection.
Disc will not play. CD Compartment Close CD Compartment
door not closed. door.
Disc inserted Reinsert disc correctly.
incorrectly.
Dirty or defective CD. Try another disc.
Moisture Wipe disc with soft cloth.
condensation on disc.
No sound. Volume setting is Increase volume.
set to minimum.
Defective disc. Try another disc.
Erratic playback. Dirty or defective Clean or replace disc.
disc.
Time reset to “12:00”. Batteries connected Check the batteries.
improperly, not connected or dead.
Clock not set. Set the clock.
Alarm does not Alarm is not activated Set and activate alarm as
turn on. or set properly. described on page 16.
Clock is not set. Set the clock.
AM or FM, no sound. Power is not on. Press POWER button
to turn the unit on.
Volume setting is Increase volume.
set to minimum.
22
SPECIFICATIONS
AUDIO
Frequency Range (AM)..................................................520–1710KHz
Frequency Range (FM)...................................................87.5–108MHz
CD SECTION:
Disc Diameter................................................................4.72” (120mm)
3.15” (80mm) Single CD
Optical Source.....................................................Semiconductor Laser
Wavelength ................................................................................780nm
GENERAL
Power Supply................................................................120V, 60Hz AC
Battery Backup ...................................... 2 x 1.5V “AAA” size batteries
Dimensions................................. 7.75 (W) x 2.5 (H) x 7.75 (D) Inches
Weight .......................................................................................... 3 lbs
Speaker...............................................................................2 x 8 ohms
FOR ADDITIONAL SET-UP OR OPERATING ASSISTANCE, PLEASE VISIT
OUR WEB SITE AT
WWW.MEMOREXELECTRONICS.COM
OR CONTACT CUSTOMER SERVICE AT (954) 660-7100.
PLEASE KEEP ALL PACKAGING MATERIAL FOR AT LEAST 90 DAYS IN
CASE YOU NEED TO RETURN THIS PRODUCT TO YOUR PLACE OF
PURCHASE OR TO MEMOREX.
FOR CONSUMER REPLACEABLE PART(S), SEE PART NUMBER(S) ON
THE LOCATION OF CONTROLS, PAGE 5, AND THEN CONTACT FOX
INTERNATIONAL AT 1-800-321-6993.
23
Memcorp, Inc.
Weston, FL
Printed in Hong Kong
Visit our website at www.memorexelectronics.com
0570-0286400-0001
Loading...